Search Documents

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind's ingenuity.

Jan 1, 1997

By Robert A. Field

Static-Load Piledriving systems utilize hydraulic push to advance piles into the ground. Dynamic systems (ie. hammers and vibratory equipment) utilize impact, or vibration, to advance the piles. Static-Load systems are most commonly utilized in situations where noise or vibration would adversely affect the people, structures or equipment located near the site. Static-Load technology is most advantageous in situations where vibration, noise or access constraints make it difficult, risky or disruptive to utilize conventional piledriving systems.

Jan 1, 1995

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989

By Gao Dazhao

This paper presents some research results of pile foundation performance. Measurements on the bearing behaviour and driving effects of piles have been carried out during pile testing and pile driving. It has been found that the ratio of end resistance to the ultimate load depends on the pile length, and the ratio in general is less than 40% for single piles. However for pile group, the end resistance seems to be greater than skin friction. The characteristic curves of skin friction and end re­sistance appear as interaction between soils and pile. The contribution of skin friction to the pile bearing capacity not only depends on soil properties but also on the relative position of the soil layer. The pore pressure and the lateral pressure in ground have been observed during the stage of driving piles. Based on the available data, the radius of plastic region and the coefficient of pore pressure A can be found analytically. The pore pressure time process curves which may be used for practice have been predicted by means of numerical method.

Jan 1, 1991

By G. Price

The Building Research Establishment installed a base load cell in a driven cast-in-place pile prior to it being tested under vertical load. The monitored base loads were found to be significantly less than could have been predicted by current design methods. The less than expected capacity was attributed to the drilling out procedure. An electro-level system installed in a second similarly formed pile, provided detailed information on the performance of the pile under lateral load. The information obtained was used to check several current design methods for laterally loaded piles. The findings show the potential dangers of attempting to improve design parameters from only limited performance data.

Jan 1, 2010

By Qi Wang, Zengzhu Kang, Jianguo Liu, Guanglei Liu

"Due to the increase of automotive vehicles, available parking spaces become a new type of limited resource in central cities of China, especially in those old districts without visionary urban planning. Additional mechanical parking in underground space is an efficient solution to provide parking spaces under the situation where the urban space is constrained. Shichahai district is an old protected zone in Beijing which is close to the Forbidden City and there are many Hutong (alleyway) and Quadrangles (courtyard house). No spaces are available for car parking on the ground and all vehicles are parking in Hutong without order currently. The local government plan to do renovation work for this district and improve the residential environment. Several innovative solutions are studied including parking in deep shafts, parking under existing buildings by under-pinned method, parking under buildings by covered excavation method, parking under roads built together with utility tunnel etc. 5000 difference types underground parking spaces are planned to be constructed in the following three years. Project examples are also introduced in this paper. INTRODUCTIONCar parking resources are very limited in central cities, especially in old districts without planning for increasing automotive vehicle volume. Traffic get worse when cars park on the side of the roads or move slowly to find parking spaces. Investigation shows the normal (parking space/ automotive vehicle volume) ratio is about 1.2 in most big cities such as New York, Tokyo and Hong Kong, while this ratio is only 0.5 in Beijing. One solution is to move cars out of central cities. But there are still huge parking requirements for the citizens living in central cities. Shichahai district is an historic protected zone in Beijing which is close to the Forbidden City and there are many Hutong and Quadrangles (refer to Figure 1 for project location). No spaces are available for car parking on ground and all vehicles are parked in Hutong without order currently. The local government had a plan to do renovation work of this district and improve the residence environment. 5000 different types of underground parking spaces are planned to be constructed in the following three years. One project designed and to be constructed by Zhongyan Technology will be introduced in this paper. Other innovative solutions will be introduced briefly as well."

Jan 1, 2017

By Richard A. Forth

During the construction of the Island Line (ISL) in Hong Kong between 1982 and 1986 piled foundations of a building were encountered in a tunnel drive. As the tunnel alignment could not be changed work was temporarily suspended whilst grouting took place beneath the pile cap. The tips of the piles were then cut off. The normal precast concrete lining segments were replaced by the "stiffer" spheroidal graphite iron segments and tunnelling resumed. Settlement of the building was found to be under 10 mm due to the tunnel drive and no damage was reported to the building.

Jan 1, 2002

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By K. Englehardt

J BERESFORD introduced the subject of the paper which is the use of polymeric slurries to support the sides of diaphragm wall and bored pile excavations during construction. In the opinion of the authors the use of a suitable polymeric fluid offers financial and technical advantages compared with traditional bentonite based slurries. Under quiescent conditions a support slurry must have the following properties. - sufficient viscosity to support the sides of the excavation, to prevent infiltration into soils and to hold loose soil particles in suspension. - when agitated it should thin quickly to assist pumping transfer and cleaning and allow free passage of the grab or drill. - viscosity should be low enough during concreting to facilitate placement but high enough to prevent contamination of the concrete.

Jan 1, 1991

Jan 1, 1990

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

By W. F. Van Impe

The design of piles and of pile groups has remarkably progressed over the past two decades. The in­creasing complexity of the building concept implements a more rational approach of the deep foundation capacity and its interaction with the structure. Moreover, the understanding of the soil characteristics relevant to deep foundation behaviour, is continuously in progress because soil parameters are always more accurately determined; which also contributed a lot to the recent developments in pile capacity design. At last, due to the increasing sensitivity of buildings to deformations, continuous attention must be also paid to pile group settlements. The aim of this report is to discuss some of the mentioned more important pile design developments.

Jan 1, 1994

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By Pan Shisheng

Amodified load transfer method computing the displacement, axial compression, skin resistance, toe resistance, and other static bearing behaviours of piles, is propoesd in this paper. Through deriving a new concrete computational method with simple integration, many complex factors, such as different soil properties of each layer in layered soil, variation of soil parameters with the changes of the depth, different elastic moduli of piles under different loads, and even different areas in the same pile, can all be easily considered. This method fits in with many types of piles, including friction and point bearing piles, precast and cast-in-situ piles. Observation of static loading test on pile is given, and the computed values from the modified load transfer method are found to agree with practical measured results.

Jan 1, 1991

By A. K. C. Chan

Recent hotel investment projects in China often involve very tight programmes for design and construction. An example given in this paper involves a 24-storey reinforced concrete hotel tower with 460 bedrooms and a 3-level podium commercial complex. The building is supported by relatively widely spaced columns and shear walls below which 88 number large diameter piers were excavated through fill, silty and bouldery clay on to dolerite and slate at depths between 15 to 3 0m below ground level. Whereas much experience has been accumulated in Hong Kong, hand-excavated pier foundation was only adopted for the first time in Dalian. This paper describes and discusses the various factors influencing the choice of the type and design of the foundation system. The criteria for determining appropriate founding levels are then explained. During installation, revisions to the acceptance procedure were made to cater for local conditions. Emphasis is placed on the role of the geotechnical engineer in making on-site decisions during construction. The advantage of the foundation system in accommodating on-site changes resulting from local complex ground conditions is demonstrated. The pier foundations were successfully completed ahead of programme.

Jan 1, 2010

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

By Mauricio Terceros, Martin Achmus, Freddy Lopez

The massive use of deep foundations had a remarkable influence in the building industry in the 20th century. Piles and micropiles made possible to erect thousands of civil structures around the world, changing quintessentially the urban and rural landscapes. Especially in urban areas, the ongoing development requires not only new infrastructure, but also to increase the capacity and/or to extend the serviceability of existing structures (buildings, bridges, etc.). Factors such as the change of use of existing facilities or the requirement to comply with updated building regulations confront Civil Engineers with the question, whether to tear down and build new structures, or to reinforce the existing structures from their foundations. Micropiling has enabled designers to come up with technical feasible solutions to retrofit the existing deep foundations, making the structural reinforcement a real option, even under considerable changes in the loading conditions. The following article presents an overview of an intervention project, where micropiles were designed to reinforce the original pile foundation of an existing building, enabling it to be reused with a different structural function. This paper will focus mainly on the analysis of the interaction between the existing piles and the reinforcing micropiles, especially in terms of settlements’ compatibility. Finally, the adopted solution, with its correspondent design considerations and execution process will be presented.

Jan 1, 2018

By Peter J. Nicholson

A new method of constructing retaining walls, in-situ, prior to excavation has been developed. This "Vertical Earth Reinforcement Technique" VERT, has been demonstrated at a full scale test wall at the National Geotechnical Experimentation Site at Texas A&M University. This 10 meter high wall, was constructed of elements of soil mixing in an array that forced composite behavior between the soil mixed elements and the in-situ soils. Inclinometers and extensometers were used to verify the performance of the wall. The construction and results of the testing are presented.

Jan 1, 1998