Search Documents

By Henk E. Brassinga

In Rotterdam a number of underground parking facilities have been built and are under development in the inner city, and in the suburbs. These parking facilities are located at already densely built areas. The design of these constructions has to take into account the impact of the building activities and that of the final construction on the surroundings. In this paper some examples of the different building methods of newly realized underground parking facilities are described, and problems that occurred during the construction are pointed out. In the soil conditions as present in Rotterdam the cost effectiveness of underground facilities can be improved by deepening the parking facility, and at the same time reducing the surface area so that the total parking volume remains constant. In this way the total volume of the diaphragm walls and the costs of the project is reduced.

Jan 1, 2006

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Donald Bruce

The three types of specifications which are used for micropile work are: ? Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. ? Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. ? Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications. Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.

Jan 1, 2004

By Joint Micropiles Committee

"The three types of specifications which are used for micropile work are: • Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. • Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. • Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications.Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.The owner, designer and contractor will together be responsible for the tasks associated with the design, installation, acceptance, and performance of the micropiles. The installation of micropiles requires specialized equipment, techniques, and appropriate workmanship. Not every detail of the work can be specified, and not every potential problem can be anticipated. Therefore, a contractor who has demonstrated experience in micropiles must be selected to execute the work required."

Jan 1, 2004

Jan 1, 1989

By Stanley A. Schwartz

In the Piedmont, heavily loaded structures are generally supported by either drilled piers or one of several pile types. The choice of drilled piers or piles is typically one of comparative costs. The cost of a drilled pier foundation is usually the more difficult to predict because of the greater impact that variable conditions and construction monitoring have on cost. Poor specifications, related to the drilling equipment, procedures and bearing level, can also result in large cost extras. In the southern Piedmont, straight shafts are typically extended down to hard rock to achieve primary support in end-bearing: when bells are required, they are often constructed manually. In some eastern and northern Piedmont locations the thickness of the decompossed rock zone is significant and considerable skin friction can be mobilized. Typically piers are constructed in holes temporarily cased with steel liners. The bottom is cleaned of loose material and water, and then evaluated by a geotechnical engineer to confirm the design bearing pressure (and friction, where appropriate) or recommend alternative construction measures.

Jan 1, 1988

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989

By S. Doombos

To convert the railway-bridge across the Oude Maas between Dordrecht and Zwijndrecht into a vertical lifting bridge, a drastic adaptation of the existing piers is necessary. Extra piles have to be placed quite close to the present piers to bear the extra weight of lift-towers and bridge-sections. This article describes the special technology applied to drive steel tubular piles l800 mm. in diameter and 36 m. in length vibration-free into position. At the same time a method of pile-point-reinforcement has been applied to minimize the settlements.

Jan 1, 1989

By Zhang Baoshan

In this paper, the forced features and dynamic behaviors of stone-column composite foundation are concisely related. The characteristics of Rayleigh wave method is summarised. This method is proposed in which, the stress ratio of the stone-column to the surrounding soil and the bear­ing capacity of the composite foundation are determined. Through the engineering cases, it is shown that, checking and evaluating the composite foundation in this method, is feasible, with high speed and low cost.

Jan 1, 1991

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

By Kenneth Pidgeon

The Boston Marine Industrial Park (BMIP) Boat Section, which is part of contract C04A2 of the Central Artery/Tunnel (CA/T) project, is currently under construction in South Boston, Massachusetts (Fig. 1). The Boat Section is approximately 900 feet long and varies in width from about 135 to 185 feet (Fig. 2). The depth to the top of the Boat Section base slab varies from about 28 to 31 feet below final ground surface and about 23 to 26 feet below normal ground water levels. The Boat Section is supported on 578 anchors drilled into the underlying bedrock each designed for a working load of 630 kips. Design and Construction Team The owner of the project is the Massachusetts Highway Department (MHD). The owner's representative is the Management Consultant, Bechtel/Parsons Brinckerhoff. The section design consultant (SDC) consisted of HDR Engineering, Inc. with GEI Consultants, Inc. as the geotechnical subconsultant. The general contractor was the joint venture of Kiewit, Perini, Atkinson, and Cashman. The boat anchors were installed by the subcontractor Delta Geotechnical Services, Inc.

Jan 1, 1994

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By Robert Thurner

The underground car park "Admonterhof in the historical centre of Graz is an example for the technical and economical success of a complicated structural design using a concept on the basis of the observational method. The intention to built a 20 m deep excavation beneath a protected monument was accompanied by some essential issues: the preservation of the existing state avoiding extensive displacements by means of a girder grid of reinforced concrete, its support on large bored piles and small steel-tube piles with possible active compensation of differential settlements, the excavation support in none built-up areas with secant bored piles, the underpinning of existing buildings with different structures by means of jet grouting. Furthermore the hydraulic gradient and the permeability of a rock formation in a part of the excavation had to be explored with the purpose to control the inflow of groundwater with a level difference of more than 10 m.

Jan 1, 2006

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

When selecting a solution for improving resiliency at facilities, such as airports, utility and transit sites, there are many options to protect structures and equipment against potential flooding. Each case involves an evaluation of the several key factors such as: design flood parameters, the geography and geological conditions below the site, the facility, and the layout of buildings and equipment to be protected. Upon reviewing these conditions and conducting a cost analysis of various options, the most suitable approach to protecting a facility can be determined. This paper will compare the conditions at various New York City sites, and give detail to the solutions utilized at these sites to improve resiliency and protect each facility. Flood wall types varied as did the strategies for raising critical equipment, to meet the Federal Emergency Management Agency (FEMA) and American Society of Civil Engineers (ASCE) 7 guidelines. Due to granular soil conditions, some sites may experience soil seepage below the flood wall resulting in the need for underground cut off systems. The authors will also present detail regarding the solutions used to control seepage. Various cut off systems will be discussed such as grouting and sheeting, explaining the factors that may impact the choice of systems. Another consideration in flood resiliency is the potential for a buoyancy condition on basement slabs when localized flood barriers are employed on first floor doors and windows. The authors will discuss the potential impacts of this condition on facilities and methods to mitigate this issue. 1. INTRODUCTION New York City is an urban coastal Metropolis with varied geology and low land areas. This includes but is not limited to sandy soils at Coney Island and the John F. Kennedy Airport. Soft marshes are found near Flushing Queens and LaGuardia Airport. Heavy rains and coastal storms caused disruption to daily life and heavily affected the economy of this vibrant City. For instance, in lower Manhattan business was interrupted in the Financial District. Power outage was widespread; commuter trains and subways were stopped and put out of service. Additionally, numerous residential homes were damaged in Coastal Neighborhoods such as the Far Rockaways and Staten Island. 1.1. Superstorm Sandy Flood Statistics On October 29, 2012 Superstorm Sandy impacted numerous facilities in the New York City Metro area. The resulting damage cost New York City more than $42 billion in repair costs. $33 billion was allocated to repair housing and infrastructure, and $9 billion was allocated to protect transit systems1. One of the major issues that impacted the city in terms of its preparedness was the high flood surge. The surge surpassed the former base flood elevation and reached as high as 13.88 feet (above mean lower low water - MLLW) in Battery Park at 9:24pm that evening. Tottenville, Staten Island experienced more damage where the water was recorded at +16 (North America Vertical Datum of 1988 - NAVD88), which is equivalent to 18.7 feet above MLLW (see Fig. 1). Not only was the surge at record levels, the waves in New York Harbor were also at record level where some buoy stations recorded waves of up to 32.5 feet. The City released “A Stronger, More Resilient New York” in June 2013, a plan laid out to rebuild communities impacted by Sandy and improve the resiliency of the infrastructure and buildings in New York City. Figures below help to illustrate the extent of the inundation relative to the projects being discussed.

Jan 1, 2018

By Charles F. Seemann

It is with considerable trepidation that I set out to defend "litigation" to Design Professionals (DPs), as a better method of resolving disputes than arbitration, in the light of my personal feeling that an increasing amount of America's productive process is being squandered in litigation. Newer methods of dispute resolution, particularly arbitration, are fashionable, and opponents of these schemes risk being viewed as cynical or self-serving. My quandary is heightened since for some smaller disputes, arbitration seems clearly the better choice. I must concede, for example, that when the cost of dispute resolution--i.e., the cost of the process (such as arbitrators fees, attorneys fees, etc.), plus the cost impact of the non-productivity of involved employees--approximates the amount of the dispute, controlling that cost may be as important as a correct resolution. This principle is particularly true for small disputes arising during the progress of a project; it is probably more cost-effective for all parties to resolve their disputes quickly than permitting the dispute to drag out.

Jan 1, 1988

By BRETTMANN TRACY

Jan 1, 2000

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960's. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000

By Michael W. Neill, O&apos

Drilling slurry has become an effective aid to the construction of drilled shafts in caving and/or waterbearing soils. Historically, drilling slurry made of bentonitic clay and water was first used in the US in water well drilling as early as 1889. In coastal Texas drilled shaft contractors began using slurry, often made of on-site clay mixed with potable water, in the years following World War II, on a relatively routine basis. This type of slurry was used to "process" boreholes, in which the borehole was drilled "in the dry" until water or unstable soil was encountered, after which water and on-site clay were introduced into the borehole and mixed in place with the auger or other drilling tool. Drilling then continued under a slurry consisting of the uncontrolled mixture of clay and water until the excavation had reached a relatively impermeable and cohesive material. At this point, a steel casing was dropped into the hole and sealed into the lower stratum of impermeable geomaterial (soil or rock). The slurry inside the casing was bailed or pumped out, drilling continued to plan depth in the dry, a reinforcing cage was set in the partially cased borehole, concrete was placed and the casing was withdrawn. Some soil-slurry was undoubtedly trapped between the casing and the borehole wall, but the quality of that slurry was usually of no concern, because engineers of the period usually viewed drilled shafts as nothing more than deeply buried footings. Any unejected slurry would only serve to lower side shearing resistance, not yet considered in design, but would have no effect on end bearing. In the 1960 's the effectiveness of soil-slurry came into question because it was often ineffective in maintaining borehole stability at marginal drilling sites and because the economy of using shaft resistance, in addition to end

Jan 1, 1991

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000