Search Documents

By R. Heikkilä

Today road construction sites utilize more and more information modeling in design phases as well as model based 3-D machine control systems in site operations. For main contractor, the management and control of all the site operations is a demanding task including also many challenges created by continuously developing new technology. In the paper, the main requirements for successful dynamic site management are introduced. The dynamic management means real-time possibilities for information acquiring, transfer and further utilization of the information in the management. An integration model to expand the current way of management and the utilization of present 3-D machine control systems is introduced. Different practical test results using two new different dynamic management systems are presented and evaluated. The first experiments and the results have been provided using the prototype system developed in a research project called DigiINFRA by the University of Oulu and Technical Research Center of Finland. Also, there have been tested a new commercial management system developed recently in Finland. In the conclusion, an expectation for the next generation for more dynamic road construction management methods is concluded.

Aug 1, 2013

By F. H. Edmunds

Introduction This paper, it is hoped, will serve as an introduction to further work upon the origin of the soils and to a more complete interpretation of the geology of Saskatchewan from a study of the soils of the Province. The great difficulty that is encountered in mapping the structure of the prairie regions of the west must be evident to all who have made the attempt. The rarity of good exposures, due to the extensive coverings of glacial drift, is the greatest obstacle, making it difficult to determine the exact stratigraphical position of such exposures as may be found. In many cases palæontological evidence is lacking, or, if available, our present knowledge of the stratigraphy is insufficient to justify division of the formations into horizons; and until many of these formations have been subjected to petrographic investigation, little can be done in using lithological differences as an aid to the correlation of the usually sparse outcrops met with in the Province. Topography may be of the utmost value as an indication of geological structure when considered in conjunction with other evidence. It does not necessarily follow that, because an area in Saskatchewan has resemblances in surface configuration to an area of oil-producing land in Texas, there is sufficient justification for sinking money in wells without further investigation. Such - investigation should include the study of available soil maps.

Jan 1, 1929

By Jean-François Dorion

In an underground mine rock reinforcement elements and surface support units are often exposed to conditions that make them susceptible to corrosion. These unfavourable conditions include high relative humidity, the presence of dust and various other particles in the atmosphere, splashing of water and gases from blasting and diesel equipment. The corrosion of support systems is often associated with a loss in capacity that can be a major safety and economic concern in underground mines. A support system is composed of several components such as bolts, mesh, plate, retaining nut, cable ties. Every individual component can deteriorate due to atmospheric or aqueous corrosion and consequently can damage the integrity of the support system. This paper reports the results of a 5-yr study on the loss in capacity of individual support and reinforcement components at selected underground hard rock mines. As part of this investigation corrosion coupons were installed at selected locations at participating mines. A number of these coupons were recovered at regular time intervals and analysed for any signs of corrosion and subsequently tested to quantify any loss in capacity. The testing of the corrosion coupons was complemented by similar tests on recovered mesh and friction bolt specimens from the site. The collected data have provided useful insights on the factors that contribute to the corrosion of support systems. This knowledge can aid in the selection of appropriate support strategies and a reliable assessment of the predicted useful life of a support system and the need for rehabilitation.

Jun 1, 2012

By J. Nalaskowski

A study of the interfacial properties of the basal plane and the edge surfaces of talc is described in this paper. The isoelectric point measured at the two different crystallographic planes by the streaming potential method was found to be similar and exists at about pH 3.0. In the case of the edge surface the zeta potential increases at higher pH values which can be attributed to the hydration of magnesium ions at the edge surface. The atomic force microscopy (AFM) colloidal probe technique was used to measure interaction forces. For such experiments a 20 um talc particle was attached to the AFM cantilever and forces between the edge of the talc particle and two different crystallographic planes of talc were measured at various pH values. These measurements, while being qualitative due to the poorly characterized contact area, show differences between the properties of the base plane and edge of the talc and correspond to the results from streaming potential measurements. Finally, the differences in the hydration of the basal plane and the edge of talc are revealed from molecular dynamics (MD) simulations. The basal plane of the talc is much less hydrated than the edge, as can be seen from the water density distribution functions, which correlate quite well with the contact angle measurements at the basal plane surface and the edge surface of the talc sample.

Jan 1, 2006

By H. Perez, A. Lavoie, V. Prévost, P. Létourneau, P. Lind

The Home smelter is a custom copper smelter located in Rouyn-Noranda, Quebec. In 2005, the smelter produced 145,000 t of copper containing 807,000 oz of gold, 20,388,000 oz of silver in addition to 515,000 t of sulphuric acid. Recently, a flexible flow sheet has been developed incorporating the intermittent use of the Noranda Continuous Converter allowing for the increasing or decreasing of production based on market conditions, while attaining 90% or greater sulphur fixation regardless of operating mode. For 2006, the smelter is operating in full production mode and production is expected to be approximately 185,000 tm of copper. Mechanical modifications, process changes, metallurgical concepts, minor element treatments, and operational techniques that have allowed the smelter to develop this flexibility are presented. Current efforts to increase the productivity of the converter aisle and anode furnaces as well as improvements being made to address fugitive emissions are also discussed.

Jan 1, 2007

By J. Ellis Thomson

For many years the value of qualitative microscopic investigation has been recognized in both of the fields of pure and applied science. In particular, its aid has been invoked in the determination of rock specimens in thin section, and some at least of the interrelations of minerals present in any one section have been observed and, to a limited extent, applied for the solution of different problems. During the past decade this form of research has also been diverted to the determination of ore minerals in polished section, with some observation of their structural relations. Microscopic research of a quantitative character, on the other hand, while started nearly one hundred years ago, has found but a limited application in petrography and has scarcely been used at all in the more modern science of mineragraphy. This is very largely due to the methods employed, since most of them consumed too much time and were, in addition, too laborious to encourage many workers in their use. The details of procedure for these earlier methods will be found in another paper by the writer, and will be omitted from this discussion as being of small interest to practical mining men.

Jan 1, 1930

By Jiachen Wang

Longwall top-coal caving mining is one of the major mining methods for extracting thick coal seams in China. The top-coal caving longwall mining was began to use in the 1980s in China, and got the rapid development. The development of the top-coal caving mining technology in China, the achievements and the theoretical aspects progress of this method are described in detail in this paper. And the main technical model of China's top-coal caving mining is introduced in this paper. This paper also introduces the application of large-cutting-height mining in China and the technical level it has reached.

Aug 1, 2013

By P. Mageau-Béland, È. -M. Proulx, M. -C. Patoine

Over the past six decades, Hatch has helped several industrial processing facilities in debottlenecking their operations, allowing them to produce more with the same equipment, to reduce and even eliminate expenditure investments, or to increase the return value of their expansion projects. These successes result from the application of a proven analysis approach that can be applied to any industrial facility. A five-stage methodology is discussed and demonstrated with a specific example of a nickel concentrator optimization study. The first stage is an observation stage which allows to meet key actors at the plant, develop mutual understanding of problems, understand operating philosophy, and efficiently collect large amounts of operating and maintenance data. Following is a data compilation stage during which data is analyzed over a representative time period to identify parameters that significantly affect the production, to evaluate data reliability and to define the focus of the upcoming analysis. Quantitative metrics are defined using statistical tools such as pivot tables, histograms, percentiles and MDR (Maximum demonstrated production rate during 3 to 7 consecutive days). Then, the production bottlenecks are identified by a thorough analysis of the facility’s control philosophy, process throughput, equipment capacity, availability, downtime causes, and interaction between components of each circuit. Understanding the maintenance practices and frequency of planned shutdown is also critical to this analysis. Opportunities for improvement are identified in collaboration with the operation, maintenance and engineering teams, ranked as a function of their impact on the bottlenecks and prioritized. The final and most critical stage involves engagement with the plant stakeholders, namely the operators and the maintenance staff members, to present the results of the analysis and obtain their participation in the implementation of the solutions. The benefits of the case study translated into: 10% production capacity gain, improved maintenance planning and avoidance of several million dollars of investment.

Jan 1, 2016

Shafts are the most important workings in the underground mines. Their technical state to a large extent determines the safety and efficiency of mining operations. However, in many cases periodically performed inspections show unsatisfactory technical state of the shaft lining (local defects, cracks, cavities, losses of the outer surface of the lining or, in case of the bricks, losses of the masonry). The most common cause of these types of damage is progressive deterioration of the lining material, impact of aggressive mine waters, impact of mining operations, deformation of the lining due to the rock mass saturation, seismic activity or periodic freezing of the lining in the upper part of a shaft. The paper presents legal requirements associated with the use of mine shafts in Polish coal mines as well as the ways and range of their control. Furthermore, examples of typical damage to shaft lining and ways to repair it, such as additional bolting, filling cavities or a wire mesh and shotcrete installation, are shown. In the final part, the paper presents a short example of a shaft, in which damage to the lining was one of the main causes of the shaft's failure. Due to the damage to the shaft lining, at the depth of approx. 65.0 m, the shaft was spontaneously filled with overburdened soil material. It resulted in a large crater to come to the surface, which, in turn, caused damage to the buildings and facilities present in the impact zone. On the surface the diameter of the crater was approx. 60.0 m, its depth approx. 11 m and the estimated volume was of about 30,000 m³. The disaster also caused disturbance in the ventilation of two neighbouring mines and the increase in methane hazard. Given the size of the crater, the measures to eliminate consequences of the catastrophe were undertaken in several stages.

Aug 1, 2013

By D. R. Boyle

"The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite _ arsenopyrite _ galena _ Bi-Sb sulfosalts _ chalcopyrite _ tetrahedrite group _ sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was transported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By D. R. Boyle

"Abstract - The Murray Brook precious metal (Au, Ag) gossan deposit is one of nine supergene mineral deposits that have developed over polymetallic massive sulfide deposits in the Bathurst Camp of New Brunswick. Reserves consist of 1.9 Mt of gossan containing 1.53 g/t Au and 65.9 g/t Ag. The supergene zone at Murray Brook consists of six distinct units: a) altered massive sulfide, b) pyrite-quartz sand, c) massive sulfide gossan, d) disseminated sulfide gossan, e) ferruginized wallrock, and f) leached bedrock. The massive sulfide gossan constitutes the main body of economic mineralization and consists of goethite, primary quartz, secondary amorphous silica, K-Fe-Pb-As- Sb-Ag hydrated sulfate and oxide minerals (beudantite, plumbojarosite, jarosite, bindheimite, scorodite), trace cinnabar, and cassiterite of primary origin. The order of stability of sulfide minerals during oxidation was pyrite > arsenopyrite > galena > Bi-Sb sulfosalts > chalcopyrite > tetrahedrite group > sphalerite.Two mass balance techniques (isovolumetric and conservative element) indicate elemental depletion in gossan relative to primary ore in the order: S>Cd=Zn>Cu=Mn>Na=Ca>Fe=Al=V> Mg= K=Se=Hg>Pb>Ti>Ag>Mo=P>Ba; and enrichment in the order Au>As>Sb>Si>Bi. Tin, as cassiterite, is conservative.Mineralogic and paleomagnetic data suggest that the gossan deposit formed under a warm temperate climate throughout the Pliocene. The rate of oxidation and the compositional nature of the ore was significantly influenced by: a) the position of the primary sulfide zone in a downward moving hydrological system, b) primary sulfide composition and zonation that promoted the development of a strong electrochemical oxidation system, and c) pronounced intercalation of carbonate and sphalerite mineralization in sulfide zones, which promoted rapid development of secondary porosity, permeability and downward flow of oxygenated groundwater.During progressive oxidation and physico-chemical erosion of the gossan zone, Au was trans- ported downward in groundwaters, probably as a Auo colloid complex, to be concentrated in the lower horizons of the gossan profile. The precipitation of Au was greatly increased in the pyrite/arsenopyrite zones. Gold concentration was multi-cyclic with continual dissolution and nucleation of the metal until final concentration in the void structures of the gossan. Leaching experiments and microprobe analyses indicate that Au is present in the gossan as submicron composite sols of Au-Ag-silica."

Jan 1, 1995

By R. Panchadhara, P. A. Gordon

"A non-local formulation of the classical continuum mechanics theory called peridynamics is used to study driven dynamic fractures in the near wellbore region. The controlled application of pressure on the inner walls of the borehole can create multiple fractures that initiate from the borehole and propagate radially outwards. The number of fractures and their final length is primarily controlled by the loading conditions and the in-situ stress state. It is the objective of this study to use a novel numerical technique called peridynamics to investigate: 1) the influence of loading conditions on the fracture pattern, and 2) the effect of in-situ stress anisotropy on fracture propagation. In peridynamics, the momentum equation from the classical theory of solid mechanics is replaced with the integro-differential momentum equation of peridynamics. As a result, discontinuities in the body, such as fractures, occur spontaneously. The material is represented by a continuum body with material points that interact non-locally with all other points within a specified distance. Fractures evolve using a damage evolution law, wherein, damage at any point is represented as the ratio of the number of broken bonds in the current configuration to the total number of bonds in the undeformed configuration.Simulations are performed on simplified test cases and the results are compared to relevant experimental and numerical studies found in the literature. It is shown that the loading rate significantly influences the number of fractures initiated from the borehole as well as their extent. Low loading rate produces fewer fractures, whereas, high loading rates produce longer and a greater number of fractures from the borehole. The numerical method successfully predicts the fracture pattern obtained from a wide range of loading conditions. Predictions also indicate that the resultant fractures are shorter when in-situ stress is applied. Numerical results show that the fracture extension is largest in the direction perpendicular to the minimum compressive stress for the range of loading rates used in this study."

Jan 1, 2015

By Y. P. Malhotra, JE. C. Carter

"Syncrude's overburden removal requirement ranges from 20 million to 30 million bank cubic metres per year to meet tarsand demands for the production of 129,000 barrels of synthetic crude oil per day. The economic tar-sand lies beneath a variable thickness of overburden materials, composed of silts, clays, some sands of lacustrine origin, wind-deposited sand dunes, and out-wash sands and gravels.For the removal of overburden, Syncrude commissioned its own mobile equipment fleet in January 1981. This fleet consists of two Demag 241 hydraulic shovels, ten Titan 33-15B trucks and support equipment. Prior to this, all overburden removal was being carried out by contractors.This paper presents an overview of overburden removal at Syncrude, with particular reference to the performance of its own fleet.IntroductionThe Syncrude Tar Sands Plant was officially opened on September 15, 1978. After an expenditure of approximately $2.26 billion, the second and the largest commercial tarsands plant was on stream toward a permit production rate of 129,400 barrels of synthetic crude oil per day. The Syncrude Plant, a joint venture of six oil companies, the federal government and the Alberta government, is a major step forward toward the goal of Canadian energy self-sufficiency.The Mildred Lake operation of Syncrude Canada Ltd. Is located 40 km north of Fort McMurray and 480 km northeast of Edmonton in the Province o f Alberta.Synthetic crude oil leaving the plant is a blend of two-third s gas oil and one-third naphtha. The two streams combine in a pipeline and flow to Edmonton. The product takes six days to make the journey, arriving at four locations in the city Imperial's Strathcona Refinery, Gulf's Edmonton Refinery, the Interprovincial pipeline terminal and the Trans-Mountain pipeline terminal. Each Syncrude owner receives a share of oil equal; to its percentage of ownership in the project. At the present time, the oil is being utilized by Canadian refineries from Vancouver to Montreal."

Jan 1, 1983

By L. A. Homeniuk, R. Bonnar

"The Athabasca Basin has been the scene of an intense exploration effort since the late 1960s, resulting in the establishment of this area as one of the major uranium districts in the world.The A thabasca Group is of Helikian age and unconformably overlies metamorphic rocks of Aphebian and Archean age. Most of the known uranium deposits have a close spatial relationship with the unconformity, graphitic meta-sediments, major northeast-trending structures and the basin edge. It should be noted that, in regard to the latter, some of the Cluff Lake deposits are exceptions.The pre-Helikian rocks underlying the Athabasca Group have been divided into six Iithostructural domains. The known uranium deposits are concentrated in the Wollaston and Mudjatik domains in the southeastern portion of the basin.The orebodies typically have a narrow high-grade portion below the unconformity and a broader, lower-grade disseminated zone in the overlying sandstone. Over-all grades average over 1% U3O8 and our estimate of known reserves totals more than 400 million pounds of contained U3O8. Some of the deposits have high concentrations of other metals, including nickel, arsenic, cobalt and gold. Ubiquitous chlorite and clay alteration is characteristic of the orebodies.Other Proterozoic basins in Canada of similar ages and having analogous geological settings to the Athabasca have received far less attention. Although little of the known uranium mineralization in these basins is related to the Helikian unconformity, there may be an exploration potential for deposits similar to those of the Athabasca basin.IntroductionThe Athabasca sedimentary basin is located within the Churchill Structural Province of the Canadian Shield in Northern Saskatchewan. The basin is elliptically shaped and is approximately 800,000 square kilometres in area.The objective of this paper is to summarize the various elements in the genesis of the unconformity-type uranium deposits of the Athabasca Basin and to evaluate the comparative potential of other Proterozoic basins to host similar unconformity-type deposits."

Jan 1, 1982

By Scott Rosenthal

?EMESRT History ?Design Philosophies (DP?s) ?Industry Successes ?Participation Thinking Differently Earth Moving Equipment Safety Round Table ? Use a critical mass to influence Marketing ? Define ?Problems?not ?Solutions? ? Leave the OEM designers to develop solutions Work within the companies to improve purchasing

May 1, 2010

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By Saba Gharedash

In this study the results of a series of numerical simulations which are conducted for one of the tunnels of the Mashhad metro line 2 project are presented to evaluate the role of tunnel face support pressure and soil strength parameters on deformation of tunnel lining and face deformation. To achieve this goal, comparative numerical simulations of a mechanized tunnel advance in soft non- homogeneous soil on top of the ground water table and beneath the building are conducted and sensitivity analysis is performed. Development of a step by step tunnel construction process is modeled using a three dimensional finite difference model (FLAC3D) taking into account all the relevant components of shield tunneling. In order to understand the mechanism of the effects of a variety of support pressures on face deformation and lining stresses, numerical simulations are conducted. It is found that the use of different face supports causes a considerable influence on the forces of tunnel lining. In addition, it is revealed that building weight help to change the stress paths and the stress distributions in the tunnel lining.

Aug 1, 2013

By J. Dubinski

Underground mining of copper ore in the Legnicko-Glogowski Copper District basin generates a number of seismic events, whose energy often exceeds 108 J (Butra, 2010). The number of tremors and their location shows that the area of rock mass involved in the deformation and failure processes significantly exceeds the area of mining operations. Locations of seismic foci of high energy tremors, as well as the aftershocks that accompany them, extend hundreds of metres, confirming that processes to restore the energy balance of rock mass occur in a short amount of time and over a wide area. Thus, an area of similar size should be considered in predictive analyses of the tremor?s position. It should be emphasized that a large portion of the rock mass still has a level of freedom resulting from the way the rock mass is held together and its geometric continuity. This level of freedom is dependent on the scale and duration of mining, the number and size of natural structures, and rock mass pressure, including gravitational pressure constricting individual fragments of rock mass in the area (Burtan, 2012). It can therefore be assumed that in real conditions, areas where mechanical strength of the layers has been exceeded may be located a considerable distance from each other and do not necessarily need to coincide with the working area location. In this sense, a rock mass influenced by mining exploitation is essentially a rock mass in which numerous fragments with concentrated energy exist simultaneously. Energy will be released within these rock mass areas each time rock mass strengths are exceeded by the induced stress changes related to mining operations. This paper presents a discussion on how to predict the location of seismic activity areas based on a change of position of seismic energy equivalents. This parameter is calculated for a given set of seismic tremors with defined foci coordinates. For a given set of seismic tremors, the location of seismic energy equivalents may be used for predicting the location of high-energy seismic events.

Aug 1, 2013

By C. E. Cartwright

That the construction of the Pacific Great Eastern railway has not been accompanied by an immediate and great development of traffic is not due to lack of natural resources in the district traversed, but to conditions that have delayed their development. Prior to the commencement of construction of the railway there was no inducement to prospect for any other mineral than gold, on account of lack of transportation. The war began soon after the commencement of construction; diverting practically all capital that might have been available for opening up the country; and since the war, capital has continued shy of new investments. If the war had not occurred it is probable that prospecting and development would have been carried out concurrently with the railway construction. Moreover, much of the district is covered deeply with drift, marine and alluvial deposits, rendering prospecting for lode mines a more expensive and slower proceeding than can generally be undertaken by the ordinary prospector, without capital. On the other hand, the presence of large porphyry dykes, granitic intrusions, and the finding of rich float in places are indications that rich miIY.ral deposits probably exist in several localities in the Lillooet district, in the Cariboo proper, and also nearer the coast. Two or three mines producing the tonnage of the? Britannia would materially alter the earnings of the railway and pay interest on the bonds. There are, however, other possibilities, in addition to large metaliferous mines, in the non-metallic minerals of the district.

Jan 1, 1925

By A. Bouajila1

Minerals processing organisations will be more and more under intense competitive pressure. Major changes are being experienced with intense respect to resources, processes, production strategies and markets. As result of international competition, only the most productive and cost-effective operations will survive. That is why operators in the minerals industry have always aimed to obtain better performance from their processes along the mineral extraction cycle starting from exploration up to the smelting step if any. A principal ingredient and perhaps the most important one in the process of evolution toward improved productivity is the achievement and implementation of an error-free production synonym of an ignorance-free operation. This is, at the same time, a guarantee for quality, a minimising factor for waste materials production, handling and disposal, and a maximising factor for labour utilisation. The notion of ?error or ignorance-free? -usually identified as a ?made in Japan? manufacturing mythology, will sound, at first impression, like a pious ideal, to be striven for but impossible to attain. Nevertheless, the introduction of measurement and detection technology in the minerals industry along the last century should benefit from the today?s sensors and control systems that explosively expanded beyond their traditional production base into far-ranging commercial ventures. The fastness and spread of those technologies will play an important role in the survival of innovative plants. Their role in information assimilation, and control of operations to maintain an error-free production environment, will help many plants to stay effective on their competitive course. In this paper the feasibility of the zero process ignorance concept as applied to the comminution circuits will be discussed and the challenge behind this ambitious move toward improved productivity will be outlined. Examples of pre-competitive R&D projects started at COREM in order to fulfil this prerogative will be presented.

May 1, 2001