Search Documents

By D. Milne, G. Snell

"A new method to predict stope hangingwall failure in underground excavations is proposed. This method compares movement rate for stope hangingwalls, determined from changes in strain or deformation, with changing opening geometry. This geometry is represented by the effective radius factor (ERF), a measure of relative distance to supporting abutments from an opening surface point. This strain-ERF (SERF) approach is applied to an instrumentation program for Brunswick mine near Bathurst, New Brunswick. The SERF method for this case study predicted failure at an ERF of 13.9 m and hangingwall failure actually occurred at an approximate ERF of 12.4 m.RÉSUMÉ Cet article propose une nouvelle méthode permettant de prévoir la rupture de l’éponte supérieure des chambres d’abattage dans les excavations souterraines. Cette méthode compare la vitesse de mouvement des épontes supérieures des chambres d’abattage, déterminée à partir des changements aux niveaux des contraintes ou de la déformation, à la géométrie variable de l’ouverture au jour. Cette géométrie est représentée par le facteur du rayon effectif (ERF, de l’anglais Effective Radius Factor), une mesure de la distance relative jusqu’aux appuis latéraux de soutènement à partir d’un point de la surface d’ouverture au jour. Cette approche contraintes-ERF (SERF, de l’anglais strain-ERF) est appliquée à un programme d’instrumentation pour la mine Brunswick située près de Bathurst, dans le Nouveau-Brunswick. Pour cette étude de cas, la méthode SERF prévoyait une rupture à un ERF de 13,9 mètres (m); la rupture de l’éponte supérieure s’est effectivement produite à un ERF d’environ 12,4 m.INTRODUCTIONUnderground stope design can be improved with the installation of field instrumentation. The most commonly used instrumentation for monitoring rock mass behaviour around open stopes is extensometers. The y-axis of Figure 1 represents how the changing rate of movement, measured using either displacement- or stress-type instruments, can be observed over time. The magnitude of movement measured by extensometers can give an approximation of the load on installed support (Milne, Pakalnis, & Lunder, 1996) and a changing rate of movement can indicate approaching instability."

Jan 1, 2018

By Peter Cunningham

Teck Facts and Figures ? Employ more than 14,000 around the world, includes: ? Over 8,600 in Canada (close to 7,800 in British Columbia) ? Close to 2,000 in Chile ? Over 2,700 in Peru ? Approximately 600 in U.S. ? Hundreds more in exploration around the world ? Total capital expenditures ? $1.8 billion for 2012

Aug 1, 2013

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By L. Don Leet

Abstract Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. The nature and magnitude of vibrations from various sources have been investigated and certain applications of the knowledge thus gained have been made. Vibrations from blasting have been measured on special equipment over a range from an electric blasting cap at a few feet, through the largest quarry shot in history to date ( 1,-362,985 lb.), to the first atomic bomb, in uew Mexico on July 16th, 1945. Laws relating amount of explosive to amount of vibration at different distances have been developed and tested. Special studies have been made of the effects of vibrations on buildings, particularly from the standpoint of possible structural damage. Recorded vibrations are used to study the effects of modern short-period delay shooting. It ?has been found that short-period delay firing is extremely effective in reducing vibrations under the right conditions, but with certain limitations. In quarry shooting, there appears to be a minimum number of holes below which vibrations are not appreciably reduced by short-period delay firing. In several instances this minimum has been near 7. Vibrations in the ground from rock bursts and the effects of mining in stresesd ground have been studied both underground and on the surface in a search for a rock burst warning system. Introduction Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. Analyses of blasting records have been yielding increasing funds of information of practical as well as theoretical interest. The nature and magnitude of the vibrations have been investigated with special reference to their effects on structures.

Jan 1, 1951

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2004

By Charles Tkaczuk

In order to remain competitive the mining industry must keep up with changes in technology. Many innovative technologies from the mining perspective are commonplace in other industries. A ?Global? review of technologies will often reveal existing technologies that can be innovatively applied in the mining industry. Industries, which are rife with proven solutions include, medicine, biotechnology, security, manufacturing, telecommunications, etc. This paper addresses the communications aspect of mining where greater productivity, lower costs and the ability to quickly react to mining related events is obtained through an increase in remote monitoring and operating control. A review of the communications systems in place globally reveals technologies that, with minimal modification, can be immediately applied to the mining environment. We discuss the concept, advantages and implementation of existing communications technology from an industry that is not usually associated with the mining industry. This technology will form the basis of a solid platform on which can be built a state-of-the-art process monitoring, control, and communication system. This lays the groundwork for providing one solution to the underground mining industry?s most difficult problem, establishing a reliable, maintainable and cost-effective underground bi-directional wired/wireless data, video and analog communications system. We need look no further than our own doorsteps to find such a solution. The cable that you see coming from the simple green or brown box on the boulevard into your home contains hundreds of television broadcast channels, FM radio channels and data channels. And if you have a set-top box, you are in control of it all. The Cable Television Broadcast Distribution System suppliers of today are at the leading edge of converging all the different methods of communications onto a common carrier, coaxial cable or fibre optic cable. There is no fundamental difference between providing a reliable communications network to a city/neighbourhood/home/personal computer than there is to a mining operation/underground level/equipment or person. The principle is the same. Only the application is different. Realizing this, we can capitalize on the efforts of other industrial sectors, to solve our communications problem. Where else can you find a solution to a problem that is mature, having been developed with the input of thousands of engineers, and having hundreds of millions of dollars spent on research and development, manufacturing, distribution, global presence and engineering support?

May 1, 2003

Automation Defined ?Using self-operating equipment to reduce human exposure to the mining environment and routine or repetitive work.?-Atlas Copco Terminology: ?Manual Operation ?A vehicle being operated by a person ?in the cab?. ?Radio Remote Control (RRC) ?A vehicle being physically operated by a person through a Line Of Sight (LOS) or Video-Remote equipment. ?Tele-Remote Control ?A vehicle being physically operated by a person at an operator station which is not necessarily located near the vehicle?s working area. ?Autonomous Operation ?A vehicle under self control with the possibility of human supervision and override.

Oct 1, 2010

By A. McLean, L. Gao, Z. Shi, Y. D. Yang, K. Chattopadhyay, G. F. Zhang

Levitation melting of metals is one of the emerging applications of magnetic and electric fields in liquid metal refining. The varying magnetic field generates induced current inside the metal droplet and leads to the Joule heating effect and Lorentz force against gravity. This contactless process can avoid contamination from the crucible and can be used to produce high-purity materials. Visualization of the levitation melting process is difficult, and thus generally investigated by mathematical modeling. In the present study, a three-dimensional mathematical model of metal levitation was developed using finite element method for proper understanding of the levitation process. The effects of harmonic magnetic field frequency, coils power input, and sample size on levitation nickel droplet were investigated. Temporal evolution of temperature fields were predicted directly though the model. Levitation and balance condition of the droplet were investigated as well.

Jan 1, 2015

By W. de Klerk, M. B. Thorpe

Golden Star Resources Bogoso operates in Ghana’s Western Region. The gold recovery plant includes; a flotation circuit producing a concentrate for the BIOX® process that oxidizes sulphides before a CIL circuit; and a dedicated CIL circuit. BIOX® uses bacteria, therefore water from the BIOX® and CIL plants remained separated; CN water could not be introduced into the flotation / BIOX® circuit. The operation built a process water inventory with high TDS and installed a process water treatment plant (PWTP). Water was released in compliance the permits but containing some thiocyanate. The PWTP brine was returned to the TSF, further exacerbating the TDS. The operation experienced a drought removing the traditional water sources; the team evaluated the options to maintain production - various water streams were laboratory tested provided options for water use. The paper presents the story (treatment chemistry and process chemistry) of continued operations by treating stored water and PWTP discharge water with peroxide; brine usage within the CIL circuit, which increased gold recovery (laboratory testing) and reduced the TDS. Water flows were further modified to include hydraulic tailings re-mining to a CIL circuits. Details of the recovery, basic chemistry and costs savings are provided.

Jan 1, 2014

By J. E. Amadi-Echendu, F. Stober, J. Ndlovu, L. R. Nelson

The Polokwane Smelter Complex (PSC) relies on a single 68MW high-intensity six-in-line furnace to smelt a planned 650 000 t/a dry concentrate to produce a platinum group metals (PGM)-bearing matte. As typical of a greenfields venture, considerable attention was paid to the project development and implementation stages of design, engineering, construction and commissioning. Somewhat unusual though, was the role of a dedicated multi-disciplinary "Operational Readiness" and support team, comprising the owners team and specialists from the furnace designer, HATCH, to effect a safe and rapid ramp-up to the design smelter capacity of 68MW. The challenges encountered in developing an effective partnership will be discussed. The modus operandi and roles of the "Operational Readiness" team during the design, procurement, construction and commissioning stages as well as that of the operational support team within the overall ramp-up objective will be presented. The "Operational Readiness" team was responsible for:

Jan 1, 2005

By M. Cossette, P. C. A?tcin

At present there is considerable confusion in the asbestos industry with regard to density and porosity measurements of asbestos. In order to clarify the situation, various notions of porosity and density are defined by means of simple schemes and clear symbols are proposed to denote them. An experimental procedure is then preposed and outlined, which is based upon Archimedes' principle. Experimental conditions at each stage of the method are explained clearly in order to minimize the opportunity for errors. Finally, the results of a study on the porosity and density of asbestos minerals having various characteristics are presented.

Jan 1, 1972

By Derrin A. Auerswald, Jacolien P. Wyethe, Nanne M. \/egter

Base and precious metal refineries often produce effluent solution and slurry streams containing between 50 mg/L and several grams per liter of base metals. Metals have historically been precipitated from these streams with lime to produce effluent streams at pH values between 8 and 9. This effluent treatment process generally does not remove alkali and alkali-earth metals or halides efficiently and with more stringent environmental legislation, more sophisticated effluent treatment plants must be considered which could for example incorporate sulphate removal with ultra-filtration, or the SavminTM process, followed by reverse osmosis for the removal of halides. The flowrates of effluents are often high and if base metals can be recovered before neutralization, the revenue generated from this stream can reduce the cost to produce clean water significantly, and in the case where high concentrations are disposed of, result in a profitable operation. As an add-on to an existing the plant the recovered metal is upgraded and recycled to the plant, but the production of a saleable metal can also be considered. Technology selection for metal recovery depends on the composition and flowrate of the effluent, but could incorporate resin-in¬pulp or other ion-exchange technology; precipitation as sulphides, hydroxides or carbonates; or solvent extraction. This paper describes, as a case study, the technology selection process and uses data from Zincor. Zincor is a division of Exxaro Base Metals (Pty) Limited, a subsidiary of Exxaro Resources Limited.

Jan 1, 2011

By K. Horikawa, S. Kitahata, H. Kobayashi

"It has been clarified that the Al-5%Mg alloys containing 200 mass ppm of sodium showed grain boundary (GB) fracture, even when tested at room temperature, as well as at high temperatures (~500°C). SEM/EDX study revealed that the GB fracture was associated with the segregation of sodium on grain boundaries of the Al-Mg base alloys. Differential scanning calorimetry (DSC) revealed that the GB fracture at room temperature of Al-Mg alloys was caused by sodium segregation in the solid state. It was also shown that the tendency of the GB fracture strongly depended on the heat treatment; the alloys after the solution heat treatment showed severe GB fracture compared with the alloys after the homogenizing treatment. Moreover, it was shown that the GB fracture at room temperature by sodium segregation was suppressed by the addition of bismuth or indium. The suppression of the GB fracture by the additional elements was believed to be the scavenging effects by forming the sodium bearing compounds in grains.INTRODUCTIONIt is widely known that Al-Mg base alloys containing high amount of magnesium(~5 mass%)show better workability at room temperature, while that the alloys show grain boundary (GB) embrittlement at higher temperatures ranging from 200 to 500°C, depending on grain size(Otsuka, 1984), sodium impurity level(Ransley, 1959, Okada, 1997, Horikawa, 2001)and testing strain rate(Yamada, 2012). In the case of coarse-grained Al-5%Mg alloys (~300 ?m), 2 mass ppm of sodium causes severe GB fracture around 300°C, however, the Al-5%Mg-2ppm alloy does not show GB fracture at room temperature. It has also been shown that the GB embrittlement caused by 2ppm of sodium was suppressed by the additional elements, such as bismuth (Talbot, 1995), antimony (Ueda, 1997) and indium (Horikawa, 2012). Basedon these facts, we have concluded that the GB embrittlement at higher temperatures of Al-Mg alloys is attributed to the synergy effects of GB segregation of atomic sodium and GB sliding. For the GB embrittlement mechanism of Al-Mg alloys, involvement of low melting point metallic phases has been pointed out (Lynch, 2002),since the GB embrittlement appeared only at high temperatures. Up to date, the effects of high amount of sodium addition more than 2 ppm on GB fracture were not fully investigated in Al-Mg alloys. In the present study, the effect of 100 ppm ordered sodium impurity on GB fracture of Al-5%Mg alloys was examined, together with the effect of another additional elements."

Jan 1, 2017

By Yoginder P. Chugh

This paper discusses design of sprays systems for dust control around a continuous miner (CM) in about 4.2 m (14 ft.) high mining areas with about 1.0 m to 2.0 m (3-6 ft.) of out-of-seam dilution mining. The challenges included low air volumes and velocity at the end of the line curtain, dust produced from out-of-seam dilution rock being very fine with 50% of the particles less than 10 micron, poor capture of aerosol through scrubber suction inlets, dust escaping through the sides of the loading pan in mining high areas, overloading of dust-laden air in the wet-scrubber, and dust rollback toward workers. The challenges were resolved through CFD modeling of airflows; improved line curtain installation, redesign and varying the spatial locations of spray systems as compared to low mining height areas. Water sprays on CM is the primary engineering control for dust control in coal mining. In 2010, the authors developed several spray system concepts for dust control (Chugh, Patwardhan, Gurley, & Hirschi (2009), Chugh & Gurley (2009), Chugh 2012). These included increased contact time between dust particles and water droplets, improved potential for the dust aerosol to be sucked in through suction inlets, and reduced dust-roll back to the operators and workers. CFD modeling was used to understand airflow patterns around mining areas and to identify spatial locations for sprays to minimize dust exposure of CM operator (CMO), haulage unit operator (HUO), and workers downwind of the operating CM in the last open crosscut (LOXC). Face area ventilation plays a key role in dilution and removal of dust generated by mining operations. High mining heights and large pillar sizes associated with longwall mining reduce the air volume reaching the face area to achieve good dust dilution.

Aug 1, 2013

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By Clyde Williams

If you would allow me some liberties, I would re-state the title of this talk as Scientific Research, Our Greatest Resource, because that title would represent more clearly a present-day conception of the metals and minerals situation. It is a subject worthy of careful consideration. Canada and the United States are so similar and interdependent in their national economies that, in the following discussion, examples of conditions in the United States may? be interpreted to apply to Canada as well. Moreover, it is a striking fact that the per capita value of mineral production in Canada and the United States in 1940 was almost the same. Therefore, in the consideration of this subject, I have made no attempt to differentiate between the two countries. The consumption of the world's mineral resources in the last few decades, and particularly during World War II, has been so enormous as to require some form of magic to ensure the continued progress of civilization in the face of a diminishing supply of these resources which are so critically essential. As Dr. C. K. Leith pointed out in 1941, industrial expansion has been so great that, during the first forty years of this century, the world used more of its mineral recourses than in all preceding history. And this did not include the all-out consumption during the succeeding five years of war.

Jan 1, 1947

By A. I. Collins, D. Danninger

Newmont has installed advanced control and online optimization on the dry grinding circuit and both roasters on its Carlin Trend refractory ore treatment plant. Subsequently, Newmont has developed a master plan for institutionalizing advanced control and optimization on all its processing units. Newmont is committed to a program of applying advanced control and optimization from crushing of ore to pouring of gold. This paper describes Newmont's experience with implementing advanced control and optimization and the benefits received. In addition, identification of advanced control and optimization opportunities and their economic justification is discussed.

Jan 1, 2005

By G. Vibert Douglas

"Gold occurs in Nova Scotia in three ways, saddle reefs, fissure veins, and fossil placers. Of these the saddle reefs are the commonest. They have been the source of most of the gold and have also been the subject of most of the literature on the gold occurrences.The Meguma or Gold-bearing series of Nova Scotia is a conformable succession of quartzite's and slates, possibly Precambrian in age, which have been folded into a number of anticlines and synclines that strike (Fig. 1) roughly east and west. This folding has been termed Acadian and is probably a westward continuation of the Caledonian revolution in Britain. It may have started in the Ordovician and continued through the Silurian and into the Lower Devonian. It was followed by the intrusion of the great Devonian granite batholiths. It is thought that the mineralization is connected with the late phases of the cooling of the granite. As the name saddle reef implies, the veins form on the crests and flanks of the anticlines, possibly in the synclinal troughs as well. The beds favoured by the solutions are the slates. The reason for this is apparent when it is realized that in order to fold over 30,000 feet of sediments (the thickness of the Meguma according to E. R. Faribault) through p radians of arc it is necessary to have a differential movement between the top and bottom beds of p times the thickness of the sediments. In the case of the Gold-bearing series, in which strong quartzite beds lie between incompetent slate beds, most of this differential movement was taken up in the slates. The evidence for this is the remarkably fine drag folding and the intense shearing and comminution of some of the beds of slate (Fig. 1). The quartzites exhibit some shearing and faulting, but there is little doubt that the greater permeability lay along the incompetent slate beds. The mineralizing solutions followed these beds and also passed from one slate bed to another through a joint or fault in the intervening bed of quartzite. These joining veins are called angulars in Nova Scotia. Within the veins the gold is in shoots and the real problem is to find out what controls the position and extent of the shoots."

Jan 1, 1954

By George B. Saunders

The mines in western Canada producing steam coal will find a better opportunity this year to market their product in Winnipeg - for two reasons: First, the new wage schedules, signed with local unions at each mine, have enabled them to reduce the selling price materially. Second, the duty on slack coal coming in from the United States has been raised to 50 cents, which is equal to the duty on run-of-mine coal. This has had the effect of raising the cost of mine-run to .the importer. Formerly, it was the practice to bring in slack coal under a duty of 14 cents and lump coal under a 53-cent duty and, by judicious mixing of the two, manufacture a mine-run coal at an average duty cost of about 22 cents. Fortunately, through efforts of the Alberta Government, and other friends of the Canadian coal trade, the Federal Government was persuaded to adjust the duty on slack coal as indicated. While it will be found that the Manitoba market, this season, is slightly more easy of access we have still a long way to go before we reach the desired goal. Geographically and economically the Manitoba market should belong to western Canada. However, it has been found a very profitable market for United States mines because large tonnages of coal can be shipped, practically at the convenience of the mines, via the Great Lakes, during seasons of slack business. They will therefore not relinquish this market without a struggle.

Jan 1, 1925

By D. Milne, P. Germain, G. Sauriol

"The practical determination of optimum stope geometry has, until recently, been an art relying primarily on experience at a given operation. Due to the complex and variable nature of rock masses in situ, stopes are often designed either very conservatively, resulting in excess development, or non-conservative resulting in excessive dilution and, in some cases, in loss of ore reserves.The Geomechanics group of the Mining Technology Division, Centre de Recherche Noranda, uses a combination numerical modelling and empirical design techniques to optimize allowable stope geometries. The above methodology allows the optim ization of stope geometry for varying rockmass classifications within an operation or between different operations. Such techniques require the development of a thorough geotechnical database at each operation and are best used when calibrated to the specific operation through back analysis.This paper discusses the above optimization techniques in light of specific examples from the Noranda Group. The design methods, limitations and results are discussed.INTRODUCTIONMine design has traditionally referred to production planning, general facility layout, (i.e. ore passes, crusher stations, main haulage drifts, etc.) and ventilation design. The dimensioning and sequencing of the stopes and pillars, however, has been almost solely based on trial and error and precedent practice.More recently, numerical stress analysis has received much more attention as part of the design process. It is common now at many operations to look at the effect of proposed stope layouts and sequences on stress redistribution through the surrounding mine workings. Through calibration of actual stope and pillar behaviour in situ, one can then relate the model predictions to support requirements, safety problems, etc."

Jan 1, 1989