Search Documents

By J. Fournier, D. Fortin, F. Robichaud

Since milling began in 1988, the Laronde mill has been expanded several times, the most recent, increasing the milling rate from 5 000 to 7 000 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails in order to cope with high silver/gold ratio associated with the discovery of the Penna shaft. Since the commissioning of the Merrill-Crowe refinery in 2000, several modification and expansion projects were performed to reduce health and safety hazards. Remarkably, several of these improvements have contributed at increasing productivity and Net Smelter Return of the refinery while reducing worker's injuries. In 2004, the refinery was audited to evaluate and quantify the circuit performance. Metallurgical and mechanical operating conditions of the refinery are now understood and areas for further improvements are well defined. This paper describes some of the factors that have contributed to this improvement and describes how ergonomics and recovery can further be improved.

Jan 1, 2005

By Hrayr Agnerian

The fair market value of an exploration property is determined by its potential to host a mineral deposit. This potential is gauged by the results of previous exploration, exploration stage, meaningful past expenditures and remaining targets that are not yet tested. Values of exploration properties can be viewed as distinct points in a three-dimensional space defined by orthogonal axes, namely: Exploration Stage (x-axis); Cumulative Expenditures (y-axis); and Property Value (z-axis). In general, these values are estimated by applying activity factors on previous exploration expenditures, e.g. an activity factor of 100% for an active property with good potential and a factor of 50% for an active property but past expenditures have not upgraded the property. At certain periods, a market factor may also be applied to reflect the activity of mineral property acquisitions. For properties that do not exhibit any exploration potential, only nominal values are applied.

Jan 1, 1996

By K. D. Eng, W. T. Tierney

"During the past century, the development of vehicular transportation has benefitted tremendously from the performance improvement in engines in a situation where low-cost, plentiful fuel supplies were the order of the day. Engine advances were enhanced by and also dictated fuel modification to better adapt the energy source to the power plant.In discussing the several aspects of the change in approach from ""an engine and its fuel to a fuel and its engine"", the authors touch on the following areas:1. Description of an engine concept that provides the needed flexibility in fuel appetite at good efficiency to cope with future requirement s.2. The constraints placed on liquid fuel resource energy utilization efficiency by special engine-required fuel properties and the fuel efficiency of the various engine types available.3. Future vehicle engine fuel sources. This review will put into perspective the problem associated with the net energy available from future fuel sources under extensive research and development at present.4. A brief review of test data to show that fuel-tolerant and fuel-efficient engines are viable and that, in a fuel-resource-limited future, they can be a ""light at the end of the tunnel.""The Texaco Controlled Combustion System (TCCS)The TCCS is a unique means for stratified charge operation of an internal combustion engine in such a manner as to eliminate the requirement for octane or cetane number specification for the fuel. Octane rating is an empirical engine test method that evaluates a gasoline's resistance to spontaneous ignition or ""knock."" Cetane is based on a different engine test, which determines a diesel fuel's ease of spontaneous ignition . High cetane number enhances cold starting and permits high-speed diesel engine operation. As one would expect, the fuels in current use cover a band when the two values, octane and cetane, are plotted against each other."

Jan 1, 1982

By Paul J. Bourassa

Alin de pourvoir aux besoins d'hébergement des quel¬ques 1600 employes qui travailleront dans toutes les spheres opérationnelles de l'exploitation du gisement du Mont-Wright, ainsi que de leurs families, Quebec Cartier a dû, avec l'aide de conseillers reconnus, et /a participation de ses employes résidant a Gagnon, étudier tour les nouveaux établissements résidentiels nordiques des dernières années tout au Canada qui dans lee pays scandinaves afin d'être en position de coneepter une agglomeration moderne répondant a toes les besoins de see future résidants. Les pre¬miers residants ont pu passer Noel 1972, et maintenant les logements prévus et construits sont °coupes a 92%.

Jan 1, 1977

By Paul Guliov

Industrial clays, including a variety of bentonites and kaolinbased clays in southern Saskatchewan are hosted by Late Cretaceous and Early Tertiary sediments. Ofparticular significance are the deposits of swelling bentonite in the Cretaceous Bearpaw Formation and the kaolinitic clays of the Cretaceous Whitemud and Paleocene Ravenscrag Formations. Swelling bentonite is currently produced in the Wilcox-Truax area by Canadian Clay Products Inc. and yields at least seven different commercial products for a variety of applications. Kaolinitic plastic clays, including ball clay, stoneware and earthenware clay, as well as kaolin in southern Saskatchewan, have a long history of development and use. Products include common and face brick, refractory bricks and other shapes, chinaware, pottery, sewer pipe, chimney flue linings and tiles. Currently clay production is for out-of-province brick manufacturing and for pottery. Recent research and improved technology combined with expansion in certain areas of the global clay industry generally hold promise for a resurgence of a clay-based industry in Saskatchewan. Products of particular promise include: clay tiles; kaolin fillers and extenders; and aluminum as well as related by-products from kaolinitic clays based on the carbochlorination process.

Jan 1, 2001

By X. S. Yuan

With the production increase of Oil Sand in Fort McMurray Alberta, more efficient tailings disposal has become a priority for Syncrude Canada Ltd. A lot of work on tailings research and development has been compiled to determine the most effective deposition to increase reclamation options, water re-use and thermal energy recovery. Efficient flocculation of fine oil sand tailings is the key technology for thickening. It was identified that flocculation of fine transition/marine ore tailings using a single flocculant was not effective. The thickener overflow contains 1-4% solids content compared with the target solids content of <0.5% obtained with Estuarine ore. As a result, novel processes for treatment of fine transition/marine ore tailings have been developed at Syncrude Bitumen Production Development since June 2004. While the conventional processes using a single flocculant, a single coagulation, or a coagulant-flocculant combination was ineffective for transition and marine ore tailings, the new processes including Coagulation-Flocculation-Coagulation (CFC), Flocculation-Coagulation (FC) and Flocculation-Coagulation-Flocculation (FCF) were acceptable options. The key components of these technologies consist of the recipe of chemicals and their adding sequence. With these technologies, almost all sub-micron clay minerals are aggregated together and settle as a whole, resulting in a clear supernatant of less than 0.1% solids.

Jan 1, 2006

By L. Chunpongtong

One of the challenges of mine planning is to determine the most cost-effective replacement time for aging equipment. The lifespan of equipment, such as haul trucks and shovels, deployed in mining operations varies due to the nature of the material and ground conditions in which it operates. For engineering economists dealing with aging equipment, the options become an economic trade-off between higher maintenance cost versus the cost of new equipment. The discount rate plays a significant role in this decision; the higher the rate, the longer the economically optimal lifespan. Therefore, the ultimate question is: ?How can the relationship between the discount rate and the economically optimal lifespan be expressed mathematically??

Aug 1, 2013

By E. A. Rychkun

"For the last 700years of recorded economic history, man has been subjected to alternating inflationary and deflationary patterns. Through this period of time, a severe deflationary pattern has developed approximately every 55 years, creating 12recordable occurrences. Through the last two centuries, this severe deflationary phenomenon has come to be known as a depression. As these depressions have repeated themselves regularly, they are cyclic. This in turn leads to the question of whether the 13th cycle will also repeat itself in the form of a depression. As this cycle is now 51 years old, we must consider the possibility at about 1984.In analyzing a 700-year record of consumer prices in Southern England, the 55-year cycle appears to vary in shape and intensity. This varying phenomenon is due to the effect of longer cycles upon which each one ""rides "". Because each cycle effectively rides on the next largest, which in turn rides on the next largest and so on, the combined measured effect of all cycles together at any point in time is always unique. This means that anyone cycle can never repeat itself in an exact identical manner. The combined effect therefore is what we observe in the form of prices and, as cycles interact, variations in deflation are produced . The ""science"" of economics attempts to quantify and develop theory on situations which are never identical and hence can be conservatively classified as a useless predictive tool.This means that more unconventional approaches may be required to predict our economic future. In looking at previous depression cycles, it is possible to recognize similarities in human behaviour patterns and hence the resulting economic movements. These behaviour patterns create major events or influencing factors which set the scene for a major deflationary condition. The way in which these factors occur, however, is not predictable. As more and more of these similar events are identified in each cycle, we can increase our confidence on the probability of the last event occurring (a depression). By also unravelling the set of larger cycles, we can determine the potential combined effect at any point in the future.This paper presents a system of cycles ranging from 800 years to 3 years which appear to operate in our economic system. By so doing, a long-term projection into the next century can be made. Finally, the paper deals with the main controlling similarities within the depression cycle, to show that a comparison with our current cycle implies that a major deflationary collapse in the mid 1980&apos;s is virtualy inevitable."

Jan 1, 1980

By C. DeLong

"The Mt. Milligan porphyry copper-gold deposits are in central British Columbia, 155 km northwest of Prince George. Mineralized outcrops and float were discovered in the Mount Milligan area by prospecting. The most recent discoveries, which utilized lithogeochemistry, were in 1983. Areas containing the outcrops and float then were investigated by geological mapping, soil and lithogeochemical sampling, ground and airborne geophysical surveys, trenching and diamond drilling. This work led to the discovery of the Mt. Milligan Main deposit in 1987 and the Southern Star deposit in 1989. Extensive diamond drilling continued until 1991 and delineated a measured and indicated resource of 299 million tonnes grading 0.45 g/t Au and 0.22 % Cu from the combined deposits.The Mt. Milligan deposits lie within the Early Mesozoic Quesnel Terrane and are hosted by porphyritic monzonite stocks and adjacent volcanic rocks of the Takla Group. The Mt. Milligan Main deposit is centred around the MBX stock and Rainbow dike, and the Southern Star deposit around the Southern Star stock.Potassic alteration is extensive within the stocks and in volcanic rocks adjacent to the MBX stock and Rainbow dike. Propylitic alteration surrounds the potassic alteration and decreases in intensuy away from the stocks. Mineralization consists mostly of pyrite, chalcopyrite, lesser magnetite, and minor bornite, molybdenite and gold.Mineralogical zoning is well-developed within the deposits. A biotite-rich subzone forms the core of the potassic alteration zone and hosts most of the copper and gold. Numerous polymetallic veins lie within the propylitic alteration zone just beyond the limit of porphyry-style copper-gold mineralization."

Jan 1, 1995

By Keith Haddock

"The Sheerness Mine, a new surface coal mine located near Hanna, Alberta, went into full production in mid-1995. The mine, which is operated by Luscar’s subsidiary Forestburg Collieries (1984) Ltd., has the design capacity to supply up to 2.1 million tonnes of sub-bituminous coal per year to the adjacent Sheerness Generating station under a 30-year contract. This paper documents the construction phase of this project and highlights the major equipment purchases as well as the construction of the mine facilities. The paper also focuses on some of the areas where cost savings have been achieved that have allowed the mine to come on stream six months ahead of schedule, and under budget. Project ReviewMine DescriptionThe Sheerness Mine is located 25 km southeast of the town of Hanna in southeastern Alberta (Fig. 1). The mining property occupies the western portion of the Sheerness CoalField and borders the Montgomery Mine, operated by Manalta Coal Ltd. in the east, and Highway 36 in the west. The Montgomery Mine and the Sheerness Mine exclusively supply the total coal requirement of the adjacent Sheerness Generating Station. The station is owned jointly by Alberta Power Limited (APL) and TransAlta Utilities Corporation (TAU). APL is the operator. Manalta’s Montgomery Mine has supplied coal to the Sheerness Station since its opening in 1986. Coal is shipped by truck from the mines over a network of haul roads to the coal receiving hoppers located on the east side of Highway 36."

Jan 1, 1997

By M. Lahtinen

Traditionally, there have been three main methods for iron removal in the hydrometallurgical production of zinc. These methods are atmospheric precipitation of jarosite or goethite and pressurised precipitation of hematite. Jarosite precipitation is without doubt the leading and the most commonly used technology for iron removal. However, jarosite precipitation has some drawbacks, such as a low iron content (and, thus, high residue volume), high moisture content after filtration and often a high zinc content. These features make any environmentally acceptable way of using or disposing of jarosite more expensive, as compared to hematite and goethite. The importance of environmental regulations has grown in the zinc industry during the last decade, which will have an increasing effect on new investments. Hematite has several advantages over jarosite, such as a high iron content, low moisture and low zinc content. An important advantage of hematite is that it is suited for further use in the cement industry. However, until now the need for autoclave equipment has limited the spread and implementation of hematite precipitation in the zinc industry. Outokumpu Technology Oy has recently developed an alternative method for iron removal, which is the atmospheric precipitation of hematite. A patented method for precipitating hematite at atmospheric pressure is presented and compared with conventional methods for iron removal. The process conditions, the quality of the hematite precipitate and the environmental aspects are also discussed.

Jan 1, 2006

By M. Massinaei

Recently constructed circuits have included multiple stages of columns in a variety of applications, from roughing to cleaning. The Miduk copper concentrator (in south-eastern Iran) is one of the unique mineral processing plants which use column flotation cells as rougher. As the bulk of final concentrate is produced by rougher columns, optimized metallurgical performance of these cells is crucial. This paper will present the study and optimization of, a froth washing system of columns. For this purpose, the cross-sectional area of orifices was increased and their orientation altered. Concentrate assay for copper and silica, in addition to bias rate were found to be the assessment criteria. Modification of the wash water system resulted in increasing the purity of rougher and final concentrate. Negative bias and short-circuiting of wash water into the concentrate launder were the main causes of improper froth zone washing in the former system.

Jan 1, 2007

By J. M. Hong, H. K. Zheng, R. Hu, C. B. Zhou

The Jinping-I double curvature arch dam, located in the middle reach of the Yalong River and with a maximum height of 305 m, is the world highest dam of the same type that has been completed. Since the second and third periods of the reservoir impounding, after which the reservoir water level was raised by about 200 m, a significant amount of leakage was observed out of the drainage holes deployed in the lowest drainage tunnel at the left-bank abutment at EL. 1595 m, with a pressure of 0.3 MPa at one typical hole when it was blocked. In this study, a number of analyses including water quality analysis, digital borehole imaging, tunnel geological mapping and in-situ groundwater monitoring were performed to investigate the source of leaking, the leakage passages and the performance of the grouting curtains. An inverse modeling procedure combining the orthogonal design, finite element forward modeling of the transient seepage flow, artificial neural network and genetic algorithm was invoked to further evaluate the permeability of the foundation rocks whose permeability was underestimated in design, using the in-situ measurements of flow rate and piezometric head. The geological structures that lead to the leakage were identified and the seepage flow behaviors in the dam foundation and the left bank abutment were assessed. Given the connectivity nature of the sub-vertically oriented fractures that induce the leakage event, it is found that some of the drainage holes with relative larger amount of discharge could be closed or blocked for reducing the amount of leakage without remarkably increasing the pore water pressure in the foundation rocks.

Jan 1, 2015

By Descarreaux. Jean

"The Abitibi volcanic belt was sampled along a cross section extending from Matagami to a point east of Rouyn. A few samples were also collected in Louvicourt township, Quebec. The major elements were determined for 344 samples, and rock names were defined using normative minerals. The analytical data were studied by means of variation diagrams. The Abitibi volcanic belt is characterized by rocks belonging to both the tholeiitic and calc-alkaline magmatic series, but they show some differences as compared to some typical reference series, particularly those from Japan. Basalt is the predominant rock type and accounts for 44 per cent of the sampled outcrops. The volcanic rocks are relatively poor in K2O and TiO2. Regionally, the volcanogenic copper-zinc mineralization is associated with the calc-alkaline volcanic sequences. Locally, within such sequences, some types of abnormal deviations from the averages are recognized only in association with the copper-zinc mineralization. The anomalies are ascribed to hydrothermal alteration consisting of the introduction of MgO and removal of N a20; enrichment in K20 is also observed where zinc mineralization predominates. Examples of such anomalous zones show that, in places, this alteration phenomenon can be quite extensive. Petrochemical characteristics can be used as geochemical ore guides in exploration programs."

Jan 1, 1973

By D. R. Reeves

This paper describes the geophysical Jogging of coal that is being carried out for the National Coal Board in the United Kingdom. An explanation of the technique is given and results are presented showing estimations of seam thickness to within ±0.5 in. and ash content to accuracies of ±2.5 per cent. The basic method of interpretation is outlined and some conclusions regarding the conditions of roof and floor material which may be deduced from the logs are explained. An indication of future developments in this field, including the identification of coal type and moisture content, is given.

Jan 1, 1971

By J. F. K. Brown

WHEN I first received the kind invitation extended to me by the Mining Society of Nova Scotia, I read over very carefully the suggested title-"The importance of long-distance planning and budgetting in modern methods of mining, and the advisability of working to some definite plan". I came to the conclusion that I might as well confess my inability to handle properly such a vast and intricate subject within the scope of any one paper. More properly, I think a round-table discussion should be indulged in-a sort&apos; of symposium carried on in similar fashion to the World Power and Coal Conferences- you know, a committee for this, a committee for that, and, finally, a committee to see what the committees are doing. Weil, your Secretary&apos;s suggestion is just like that- much too comprehensive for any half-hour&apos;s presentation. As a paper, also, it either becomes too general and therefore uninteresting, or i.t descends into detail and describes means and methods to the end desired, which have little attraction because they were designed to meet quite different conditions than those my audience would mentally be considering. Of the two evils facing me, I have chosen the one that sticks to the generalities. Your Secretary&apos;s query almost automatically divides itself into two distinct phases: First, the importance, and second, the advisability, of planning. Let us dwell for the moment on the second, because, if we can prove advisability, that leads to desirability and, finally, to doing. Proving is the difficult part of the little problem. Here was something I, personally and as a mining engineer, had been battling for all my corporate life without being able to prove it to anybody. Then I saw the way out of that. I perceived I could put that little question of advisability on another basis altogether-:put it in the class of "coming- some day- soon" whether you or l or anybody else liked it or not; call it, if you please, mandatory, certain, necessary, enforceable planning. All of which means that the problem of advisability has rather suddenly become the very practical one of "how to do it". Why?

Jan 1, 1937

By D. O. DeGagné, J. F. Archibald

Spray-on polymer linings, as partial or full replacement for traditional forms of area rock support, have seen rapid growth in interest within Canada. A wide variety of lining types, ranging from polymer chemical to water-based cementitious materials, have been developed and commercially introduced to the underground mining market. Following approximately one decade of development work, several general conclusions have been reached regarding the performance of this class of area support media, these being that: health and safety assessment of the broad range of materials has shown the majority of them to be acceptable and safe for underground use; significant ground support potential can be offered by them, being equivalent to or better than capabilities offered by traditional support forms such as bolt-and-screen or shotcrete, and; their abilities to be rapidly deployed and provide near instantaneous support restraint offer considerable operational and cost benefits to underground operators. A review of currently available liner materials, their historic development within the Canadian mining industry, and overviews of support, health and safety, operational considerations and cost benefits are provided in this paper.

Jan 1, 2001

By Jaeheon Lee, Junmo Ahn, Isabel F. Barton

"Newmont’s Mike prospect, currently undeveloped, is a blind Cu-Au(-Zn) deposit on the Carlin Trend, containing >8.5 M oz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn as Carlin-type gold and polymetallic Cu-Zn minerals in Paleozoic lower-plate carbonates and shales. This project was undertaken 1) to examine the effectiveness of different lixiviants for leaching the Mike supergene Cu-Au ores via bottle roll tests, and 2) to determine what ore minerals resist dissolution in each leaching agent by comparing the mineralogy and chemistry of head and tail samples. Sulfuric and sulfurous acids were used to leach copper and cyanide was used to leach gold. Thiourea, glycine, and other lixiviants were used to leach both base metals and precious metal. QEMSCAN and SEM study of six samples of different ore types and grades indicate that the Au occurs as varieties of native gold, including auricupride and electrum. Major Cu minerals are native Cu, cuprite, malachite, chrysocolla, and conichalcite (Ca-Cu arsenate), with locally significant Cu in jarosite and goethite. Gangue mineralogy is dominated by quartz, sericite, chlorite, alunite, smectite and kaolinite, K-feldspar, and iron oxides (sensu lato). Results of bottle roll tests and leach residue mineralogy will be presented and discussed at the conference.INTRODUCTION Resource and Geologic Setting The Mike deposit is a large, blind Cu-Au(-Zn) deposit in the Maggie Creek district of the Carlin Trend of Nevada, USA, near the Gold Quarry mine (Figure 1). The mineral inventory, based on drilling, is 8.568 Moz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn at average grades of 0.72 g/t Au, 0.34 wt% Cu, and 2.13 wt% Zn (inventory for a cone at $400/oz Au and $0.80/lb Cu by Norby and Orobona, 2002)."

Jan 1, 2017

By W. J. Cherones

This paper describes the history of the development and application of the electric mining shovel in open-pit mining, dea1ing particularly with far-reaching advancements in three primary areas: metallurgy, mechanical design and electrical systems. Hoist drives and crowd drives, including the Magnetorque and Electrotorque systems, and the integral propel drive are given close attention.

Jan 1, 1972

By Floyd B. Bowen

Pumping methods are used, almost exclusively, to transport materials in the mining, beneficiation and chemical processing of phosphate rock in the Florida phosphate pebble field. Matrix pumping systems capable of pumping 15,000 g.p.m., transporting 15,000 long tons (dry) per hour, are now in use. They utilize 16-by 48 Yz -in. pumps, driven by 1.250-h.p. motors, discharging into pipelines 20 inches .in diameter .and sometimes several miles in length. As an average, it is necessary to pump 3 tons of matrix to the beneficiation plants, and to dispose of 2 tons of sand tailings and clay as waste, in order to produce 1 ton of shipping-grade rock. The washers and flotation plants, where the clay and phosphate and silica particles are separated, require the movement of large volumes of slurries with densities ranging from 2-3 per cent to 45 per cent solids, by weight. Extensive waste disposal systems require the pumping of dilute clay slurries in quantities of up to 50,000 g.p.m.,

Jan 1, 1963