Search Documents

By Robert A. Stansbury

Keeping development ahead of retreat mining is a problem which occurs nearly everywhere longwall mining is used in the United States. As improved equipment technology has allowed the application of longwall mining to more difficult mining conditions, and with higher retreat rates, the problem has become more critical. Many factors determine development speed, including roof and floor conditions, mining heights, seam heights, and the number of entries. In an effort to maximize the rate of development and production from development sections, U. S. Steel's Gary District has used five entry, three entry, four entry and is planning two entry development panels at its different mines. With the introduction of various types of shield supports, it is now possible to utilize longwall mining in higher coal over 3 meters (10 feet), lower coal under one meter, in difficult roof conditions, and with soft floor. Improved shearers of 300 KW (400 HP) and more make cutting heights over 3 meters (10 feet) possible, and off pan shearers and improved Gleithobel plows make cutting less than 1 meter (40 inches) seam height possible. Longwall mining under these conditions puts an added strain on the ability to develop panels as fast as they are retreated. Poor roof conditions require a substantial amount of additional roof support to ensure that roof control in the head and tall entries will not hinder longwall retreat. The additional measures of longer bolts, resin bolts, point anchor resin bolts, roof mats, roof trusses, steel or wood cross bars, and roof grouting all place an additional burden on man power, installation time, and cost on the mining cycle. Additional roof bolting on development can cut the potential mining rate in half, and any roof falls cause significant delays to mining. Timbers and cribs can restrict ventilation and require more entries. Soft floor conditions can greatly impede development through tramming difficulties with shuttle cars and roof bolters, time required for cleaning and repairing roadways, and maintenance difficulties on equipment. High coal sometimes requires rib support to be Installed during the mining cycle, further cutting the mining rate. Mining low seams requires that roof or floor be mined in the head and tail entries as well as the track or tractor roadway entry to provide clearance of the longwall equipment. Mining this rock slows down the mining rate because of the extra material being mined and the extra wear and tear on equipment. To a large degree these conditions effecting development speed cannot be controlled.

Jan 1, 1981

By William E. Ford, Edward Salisbury Dana

This section includes one distinct group, the Stibnite Group, to which orpiment is related; the other species included stand alone. Pyr., etc. - In the closed tube melts and gives a dark red liquid when hot and a red- dish yellow solid when cold; in the open tube (if heated ver slow? ) sulphurous fumes, and a white crystalline sublimate of arsenic trioxide. B.B. on ciarcoaTburm with a blue Hame, emitting arsenical and sulphurous odors. Soluble in caustic alkalies. Artif. - Realgar is frequently noted as a sublimation product from furnaces roasting ores of arsenic. Crystals are produced when arsenic sulphide is heated in a sealed tube with a solution of sodium bicarbonate. Obs. - Realgar occurs usually in veins associated with silver and lead ores. It has been found in volcanic regions as a sublimation~duct. It has also been noted as a deposit from hot spring waters. It is often rtasociate wlth orplment. It occurs at Felsi5bBnya, Kapnik and NagyAg, Hungary; Allchar, Macedonia. Binnental, Switzerland, in dolomite. In the United States, at Mercur, Utah; in the Norris Geyser Basin, Yellowstone Park, as a deposition from the hot waters. Found at the Monte Cristo millin district, Snohomish Co., Washington: the namerealga7 is from the Arabic, Rahj af gh&r,powder of the mine. Use. - Was used in fireworks to give a brilliant white light when mixed with saltpeter and ignited. The artificial material is now used for this purpose.

Jan 1, 1922

By LEWIS F. THOMAS

MINING geologists and mining engineer, rarely give due thought to the geography of mining deposits. They realize, it is true that what may be ore in one place would be only worthless rock in another because f the in accessibility of a smelter r a market; and they may consider the lack of a supply of labor, or water, or power to carry on operations. But they do not think (of these things in terms of geography. Geography may be defined as the science of relationships between earth and man, so geographers are vitally interested in the how and why of mining as it is carried on at different place, having entirely different environment-. Such environments are geographic complexes or composites of natural and cultural elements, which are listed and briefly discussed in the following paragraphs.

Jan 1, 1941

By D. J. Carney, E. Richard Randolph, E. Van Meter, J. J. Oravec, Stanley H. Ward, Gerald J. Anderson, Rolland L. 203-000-000-005 Blake

DURING the last 30 years the inductive electromagnetic method has been used chiefly in the search for massive sulphide mineralization. This application has met with varying degrees of success and in recent years has resulted in discovery of several large orebodies. Little has been written concerning its use in exploration for soft iron ores, but one of the present authors has reported on experiments with massive magnetic deposits.' To augment the exploration tools available to geologists in delineating iron orebodies, Cleveland-Cliffs Iron Co. and McPhar Geophysics Ltd. undertook in 1953 to apply the inductive electromagnetic method to Cleveland-Cliffs properties in the Lake Superior region. As a result of this project, equipment has been developed that enables simultaneous transmission of two audio frequency waves, and the field technique and interpretative procedure involved have furthered exploration in the district significantly. Thus far, inductive electromagnetic application in the Lake Superior region has been only a development tool, that is, it is used to locate obscured contacts and faults as a part of property expansion and development. However, its application to primary reconnaissance of unexplored areas may be feasible in the future. The method has assisted in placing drillholes efficiently, and the elimination of excess drilling foot-ages and/or actual elimination of unnecessary holes has amply justified the expense of the geophysical survey. Cost of the field work involved is comparable on a per station basis to the cost of a magnetometer or superdip survey. Since observations require no reduction, i.e., are directly interpretable, overall expenditure is low, and the scope and detail of the survey can be adjusted in the field as geological- geophysical correlation becomes evident. To a great extent, this eliminates the second-guessing so commonly arising after office calculations are completed on data obtained with other types of geophysical surveys. This unique feature of field interpretation and its associated intimate feel of the project area, is, perhaps, one of the most valuable aspects of the inductive electromagnetic method as applied to iron ore exploration. Basis of Method Fundamentally, the method involves transmission of an alternating electromagnetic wave, of a chosen audio frequency, which permeates the ground materials in the vicinity of a transmitting, or primary, coil, see Fig. 1. This wave, or field, induces an electric current in any conductor on which it is incident. The flow of an alternating current in a conductor sets up its own, or secondary, radiating electromagnetic field. These two fields form a resultant whose configuration depends on the following characteristics of the subsurface conductors: 1) size, 2) shape, 3) electrical conductivity, 4) magnetic permeability, and 5) frequency of the transmitted wave. To a lesser extent the resultant is also dependent on material adjacent to the conductor, topography, and surface conductivity. For illustrative purposes, the primary, secondary, and resultant fields may be represented by vectors. In operation, the direction of the resultant vector is measured by a small receiving coil tuned to the frequency of the transmitted wave. Generally speaking, the method can be compared to the transmission and reception of the familiar radio broadcast, with special variations permitting measurement of the effect on reception of intervening materials. Field Technique Mechanics of field operation are simple. The mast is set up in a vertical position and is then guyed in place. The transmitting loop then is raised by means of a sheave at the top of the mast and the coil connected to the motor-generator. A special plane table is clamped into position on the mast and the loop is plumbed. The plane table is oriented according to a grid system established over the project area. By means of this plane table it is possible

Jan 1, 1956

By AIME AIME

At the Annual Meeting of the Institute, February, 1908, the following amendments to the Constitution were proposed for action at a future business meeting (see Trans., XXXIX, xxvii) To Art. II. After the first sentence of this Article, add the following sentence « These classes may be subdivided by the Council, according to profession, length of membership, nationality, or other conditions not inconsistent with the provisions of this article." To Art. III. In the first line, substitute " fifteen " for "ten " dollars. At the Annual Meeting of February, 1909, action upon these amendments was postponed to the next business meeting (see Bulletin No. 27, March, 1909, p. xiv). Of these two amendments, the first has been withdrawn, as unnecessary-the subdivision thereby authorized being already practicable without such amendment. The second amendment will be acted upon at the next Annual Meeting, February 15, 1910, and the Secretary has been instructed to call the attention of members to the subject in such a way as to secure a general vote upon it. A special circular, now being prepared by the Secretary, will shortly be sent to all members. Year Book of the Institute. The Year Book of the Institute for 1910 is sent to all members and associates with this issue of the Bulletin. In addition to the lists of members enrolled Jan. 1, 1910, and arranged both alphabetically and geographically, this annual contains lists of officers, council, corporation, past officers, meetings, and notices concerning publications; also the constitution and by-laws of the Institute, and blank forms for proposal of mem-

Jan 1, 1910

By William E. Ford, Edward Salisbury Dana

IN the representation of crystals by figures it is customary to draw their edges as if they were projected upon some definite plane. Two sorts of projection are use8; the ah- graphic in which the lines of projection fell at right angles and the chirographic where they fall at oblique angles upon the plane of projection. The second of these projections is the more important, and must be tr2atcd here in some detail. Two points are to be noted in regard to it. In the first place, in the drawings of crystals the point of view is supposed to be at an infinite distance, and it follows from this that all lines which are parallel on the crystal appear parallel in the drawing. In the second place, in all ordinary cases, it is the complete ideal crystal which is represented, that is, the crystal with its full geometrical symmetry as explained on pp. 10 to 13 (cf. note on p. 13). In general, drawings of crystals are made, either by constructing the figure upon a projection of its crystal axes, using the intercepts of the different faces upon the axes in order to determine the directions of the edges or by constructing the figure from the gnomonic (or stereographic) projection of the crystal forms. Both of these methods have their advantages and disadvantages. By drawing the crystal figure by the aid of a projection of its crystal axes the symmetry of the crystal and the relations of its faces to the axes are emphasized. In many cases, however, drawing from a projection of the poles of the crystal faces is simpler and takes less time. The student should be able to use both methods and consequently both are described below.

Jan 1, 1922

By Dennis H. Laubscher

INTRODUCTION The selection of mass mining methods is the situation facing not only planners of new operations, but also those involved with cur- rent operations, including the eventual change from open-pit to underground. Increasing ground control problems on many mines, plus a better understanding of dilution and ore loss problems have meant a review of current mining methods and support techniques. Experiments are only successful if conducted in the right mining environment and on the right scale. Mining personnel have been known for their conservatism and will tend to persevere with an established method rather than change; often, hidden costs will obscure the correct economic assessment. An established mining sequence is not necessarily correct in the long term. However, recommendations to change are usually met with opposition because of inconvenience, temporary production problems and the desire for a trouble-free guarantee. In any planning exercise, care must be taken that time and money are not wasted in trying to achieve the unattainable. During the decision-making period, production personnel must be involved, and, if possible, they should visit similar omrations to that proposed. Co-operative production personnel will help ensure success. Descriptions of mining methods are available in technical papers and books, and it is not intended to discuss this aspect, but, rather, the various factors which must be recognised before arriving at a final selection. In another paper presented at this Conference (Heslop and Laubscher, 1981) factors affecting ore recovery and dilution are discussed in greater detail for various cave mining methods. PRELIMINARY CONSIDERATIONS Comprehensive Geological Data. Geological information is available during the exploration stage, but, often, core from exploration drilling is not analysed with the selection of a mining method in mind. Drilling costs are high, therefore the maximum benefits must be derived from this operation. Holes which have not intersected ore may provide data on possible shaft sites, and 35 mm colour slides of core, sound logging and geomechanics classification, will provide a record which can be used with confidence at a later date. Intersections of the various rock types should be kept for future study; for example, is weathering likely to be a problem, bearing in mind that this can be accelerated in the warm, humid atmosphere of an underground mine. The accumulation of data required to select a mining method starts with initial geological work in the target area, whether this be surface mapping or a diamond drill hole. Publications. As technical papers, reports and books are used in the selection of mining methods, an appeal is made to authors to describe the geological environment so that readers can relate to their own conditions. Not enough emphasis is given to the problems experienced and the techniques employed to overcome them. Follow-up papers are seldom written and we should be prepared to discuss our failures. Diagrams are often misleading, as the ideal and not actual situations are depicted. The caved ore/waste interface is not a straight line, and whereas this may not be significant in a diagram of a 200-117 draw height, it certainly is in sub-level caving with draw zones only 1 - 2 m width but up to 20 m high. SUMMARY OF FACTORS AFFECTING THE SELECTION OF UNDERGROUND MASS MINING METHODS (a) Regional rock stresses and mining geometry. (b) The geomechanics rock mass classification of the orebody and surrounding rock mass. (c) Ratio of the surface area of the ore/unpay interface to the contained ore which determines ore losses and dilution. (d) The cavability and fragmentation data of the ore and hangingwall. (e) The mineral distribution in the orebody and its dilution zone.

Jan 1, 1981

By Arthur F. Colombo, Donald W. Frommer

With the opening of the Tilden mine near Ishpeming, MI, a new era in iron ore beneficiation was begun. A description of a U. S. Bureau of Mines investigation is summarized to illustrate the selective flocculation-deslime-flotation process developed by the Bureau and used at the Tilden concentrator, which is also briefly described. The operating parameters for the selective flocculation-cationic flotation of an oxidized taconite from the Mesabi range are discussed. A water reclamation system using lime and a cationic flocculant was applied to reclaim the effluents from a 900-pound-per-hour flotation pilot plant. About 80 percent of water requirements were recovered, and the calcium content of the reclaimed water was found to be more important than clarity in influencing the selective flocculation and flotation processes. Although reclaimed waters with about 10 ppm calcium registered turbidities of approximately 5,000 ppm SiO2 equivalents, the concentrates produced using these waters contained 64 percent Fe and 55.0 percent SiO2 and had accompanying iron recoveries of 75 percent. Lower grade concentrates resulted from using reclaimed water with higher calcium contents and lower turbidities.

Jan 1, 1976

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The microhardness of single crystals of tungsten disilicide has been investigated by the Knoop method. The average random room-temperature hardness of the WSi, matrix was 1350 kg per sq mm. Hardness crnisotropy was noted with respect to plane and indenter orientation as determined by single-crq.stal X-rny studies. Annealing at 1600" and 1800°C decreased the average hardness to 1310 and 1230 kg per sq tnm, respectively, and produced a second phase identified by X-ray diffraction and electron-microprobe analysis to be wSio.7. Ball-impact experiwzents produced rosettes at 850°C. Optical and electron microscopy showed evidence of slip and cross slip and twinning produced by microhardness indentations. Prismatic (100), [001] slip was found and cor~elated with hardness data. THE present study was undertaken to investigate the hardness anisotropy of as-grown and annealed single crystals of tungsten disilicide. The existence of the silicide WSiz in the W-Si system has been well-established and its structure thoroughly investigated zachariasen2 found WSi, to have a tetragonal C type of structure, similar to that of MoSi, with lattice parameters a = 3.212A, Kieffer et al. studied the W-Si system and measured the density and microhardness (at a 100-g load) of both polycrystalline WSi, and WSi,.,. The values found were 9.25 g per cu cm and 1090 kg per sq mm for WSi,, and 12.21 per cu cm and 770 kg per sq mm for WSi0.7, respectively. According to Samsonov et a1.5 the microhardness of polycrystalline WSi2 is 1430 kg per sq mm (at a 120-g load). EXPERIMENTAL The WSi, single-crystal boules investigated in this paper were grown by a Verneuil-type process using an electric arc by the Linde Division of the Union Carbide Corp.6 The largest specimens were 8 mm in diameter by 16 mm long. The crystals had an average density of 9.01 g per cu cm with a tungsten • silicon content of 99.9 wt pct. The major impurities were: 87 ppm O, 41 ppm N. 54 pprn C, 500 ppm Zr, 50 ppm Na, and 50 ppm Mn. The crystals were silicon-poor, the average silicon content being 22.20 pct (stoichiometric value is 23.40 pct), and tungsten-rich, the average tungsten content being 77.70 pct (stoichiometric value is 76.60 pct). As-received single crystals were ground and analyzed by powder X-ray diffraction technique using Cu Ka radiation. Laue and layer line rotation patterns were obtained on cleaved sections of WSi, single crystals. Electron-microprobe traverses of representative crystals were done using a Phillips-AMR electron microanalyzer. Carbon replicas were used to prepare electron micrographs. This work was done with a JEM-6A electron microscope. Prior to the metallographic examination, the specimens were mounted in Lucite and then polished for short times on polishing wheels using 9-, 3-, and 1-p diamond-grade pastes. Finally they were fine-polished with Linde A powder for 24 hr on a Syntron vibratory polisher. The samples were etched with 4H 2 O:1HF:2HNO3, which is a medium fast-acting etchant. The combination 1HF:2HNO3:5 lactic acid is also a satisfactory etchant. Annealing runs for selected specimens were made at 1600" and 1800°C for 3 hr at 1.0 to 3.0 x 10-5 mm Hg. A Brew tantalum resistance furnace with WSi2 powder for setters was used. The WSi2 powder was the same as that used for the crystal growth. Temperatures were measured with a calibrated W, W-26 pct Re thermocouple and a microoptical pyrometer. Powder X-ray diffraction, emission spectrographic, and electron-microprobe analyses were done after the annealing runs. For microhardness measurements a Tukon Microhardness Tester Type FB with a Knoop indenter was used. Although measurements were taken at loads ranging from 25 to 1000 g, the 100-g load was chosen as the standard load. All measurements were taken at room temperature. Only indentations of cracking classes 1 and 2 were considered.' DISCUSSION OF RESULTS Powder X-ray diffraction analysis showed the as-received crystals to be single-phase WSi2. Laue and layer line rotation patterns obtained on cleaved sections of WSi2 single crystals proved them to be tetragonal WS 2 2 The results also indicated that the c axis of the crystal was oriented parallel to the boule or growth axis. Electron-microprobe traverses across the matrix of the as-grown crystals showed them to be homogeneous WSi,. Optical and electron microscopy of etched crystals, however, revealed that they contained minute amounts of the "golden" and the "blue" second phases as opposed to the "white" or WSi2 phase. These two second phases were concentrated in inclusion and etch-pit

Jan 1, 1965

IN order that you may be expert in every phase of this art of parting, I wish to caution you upon twelve points, all necessary, so that you may know beforehand what may happen to you and what provision you must make to obtain good results. Understand that the gain derived from this art lies in carrying out the work that you wish to do accurately and with profit, which means nothing other than working with certainty and seeing that there is no loss of gold or silver [69v] or substance of anything that is valuable in itself. For, since everything lost is silver or gold, it is valuable however little. it may be, and many little things obviously make one large one; for gain increases gain, and loss, loss. Therefore, you will have as your first task to seek to have the materials that you are to use for making the aqua fortis of as perfect a nature as possible. I tell you this because the saltpeter is often weaker and of worse quality than the alum. For this reason it is necessary to make an effort to have it not only well refined and free from earthiness but also of a nature as powerful as pig [dung] saltpeter, the color of which tends strongly toward yellow. In order to work better, you also refine this again before you put it to use, as I shall tell you in its place. Likewise, see if you can get alum of the red kind that comes from the Levant or from Cartagena, for it costs less and is more powerful. Furthermore; see that you have a good number of well-formed cucurbits of properly purified glass not too large and of, equal content and size. Above all, see that they contain, no indentations, bubbles, folds, or scratches, especially, in the, body or in the bottom, because they break easily and the nature and great force of the acid pierces them by eating away, and makes a little hole. For this reason, cucurbits. are always divided into four grades; one is taken for making aqua fortis, another for drying the waters when they are laden with silver, the third for recovering the acids from the separations, and the fourth are either rejected as useless or dangerous, or are saved for recovering the whites or for some other service. Whoever wishes to practice this art well should remember to keep a large supply of cucurbits, receivers, and alembics. The third is the precaution which one must take in luting them; first, to

Jan 1, 1942

By L. T. Leyson, U. C. Tainton

Some time ago, at ameeting of the Institute Prof. J. W. Richards1 said, "I take exception to the statement that all the factors in the production of electrolytic zinc were known long ago.... There is possible in my opinion an improvement of perhaps 50 per cent. in the new electrolytic processes." An examination of the literature of the subject will show the justness of Professor Richards' contention. The work of the earlier investigators was carried on in the shadow of difficulties that, today, are hardly more than memories. We seldom hear now of zinc sponge, that bête noir of the electrolytic-zinc pioneers. Zinc sponge was the name given to a peculiar, soft, black, non-adherent form of zinc deposit that was utterly useless for melting into ingot form. At the big plant at Cockle Creek, New South Wales, in 1897, Edgar Ashcroft2 said that the solution in the plant would suddenly, and without ascertainable cause, go' "bad" and begin to deposit spongy zinc. The most delicate, even spectroscopic, methods of analysis were unable to detect any difference between "good" solution and "bad" solution; either form might change to the other on being kept for a while. When it is added that an outbreak of this insidious disease (which appeared to be infectious, or at least contagious) could be dealt with only by discarding the solution and washing out all tanks and pipe lines, some idea may be gathered of the troubles of the zinc electrometallurgist in what may be spoken of as the "sponge age" of electrolytic zinc. Thanks to the efforts of a number of investigators, we are today able to diagnose with considerable certitude the nature of the malady that puzzled Ashcroft and his co-workers. The researches of Mylius and

Jan 1, 1924

By Thomas T. Read

REVIEWING the events of the year in mineral industry education, a certain amount of either amusement or irritation, depending upon one's viewpoint, can be derived front the section dealing with mining engineering in Walter B. Pitkin's "New Careers for Youth" which appeared during the summer. On p. 102 Prof. Pitkin says "The mining engineer is disappearing .. . because . . . the profits of mining decline rapidly with the age of the mine." In his "Are Too Many Students Taking Mining Courses?" published in the May issue of this journal, W. B. Plank presents statistics showing that there was some decline in student enrollment in mining and metallurgical courses in 1932-3 and 1933-4, compared with 1930-31, but that the decline was proportionate to that in all lines of engineering study combined. Informal reports from Institute officials that have visited tinning schools during the fall indicate that nearly all schools showed an increase in enrollment for the current school year. Pre else statistics will be made available by Prof. Plank at the Annual Meeting. His study last year provided, for the first time, accurate and complete information on the enrollment in mining schools, as well as the number of various courses and the degree granted, and it will be interesting to have comparable figures for this year. Prof. Pitkin's views on the future opportunities for mining engineers were discussed at some length - on pages 439-4.40 of the November issue of MINING AND METALLURGY.

Jan 1, 1935

By J. A. Heskett

NEW ZEALAND is dependent on the outside world for its ferro goods, yet it can boast of at least two well-defined iron-ore deposits; namely, Para Para limonite, 3 Fe203 + 21120 also found as lower hydrated oxides, and Taranaki iron-sand, a combined magnetite and ilmenite, 2FeO + 2Fe203 + FeO + Ti02. The former is of massive variety and the FIG. 1.-VIEW OF WORKS SHOWING IRON-SAND DEPOSITS, ALSO WHARF AND BREAK¬WATER IN THE DISTANCE. latter granular and mixed with various proportions of fine shell and siliceous sand well water-worn. This latter deposit forms the greater portion of the beach sands of the west coast of the North Island of New Zealand. It is so fine that the whole of a sample passed through a sieve of 40 meshes to the inch. The ilmenite cannot be detected by the microscope, as in the titaniferous ores of the Adirondacks, nor can it be magnetically separated, as in the titaniferous ore of Natashkwan, Canada. To all appearances it is a chemical compound of the double oxides of iron and titanium and not a mechanical mixture, as is the ore of the Adirondack deposits.

Jan 8, 1920

By Dennis K. Mortensen

Startup of the 9000 tpd Sacaton concentrator is expected to increase Asarco's domestic copper concentrate capacity by 21%. The plant site is located due west of the mining operations, consisting of both crushing and concentrating facilities. Arthur G. McKee & Co. served as the prime contractor for the project. The Sacaton mineralization contains both sulfide and oxide ores. Primary mineral constituents are chalcocite, azurite, malachite, chrysocolla, and minor amounts of silver and occasional gold. Sulfides are distinguished from oxides when more than half the total copper content is in the form of a sulfide copper mineral. While non-sulfide copper minerals are considerably less prevalent throughout the orebody, they tend to occur quite intimately with the sulfide minerals, particularly in the upper zones of the mineralization. For this reason the decision was made to treat all the ore in a flotation circuit using existing sulfidizing methods.

Jan 11, 1974

By J. M. Callow

THE results obtained by pneumatic flotation throughout the country on all classes of ore, and. the tonnage now being treated by this particular method, speak for themselves. Its advantages over the so-called agitation process are now established by facts and data from practice. The comparative efficiency of a rapidly revolving paddle, as a means for aerating an ore pulp, and of a cycloidal or turbine blower for the same purpose, would seem to be so obvious as to leave no room for discussion. Practitioners in this art are to be congratulated on the acquisition of the valuable literary contributions that have recently been made on the theory of. flotation by Messrs. Ralston, Van Arsdale, Taggart and Beach, and others, and the very valuable and able articles, by Messrs. Laist and Wiggin on "Flotation Concentration at Anaconda, Mont.," by, Dr. Rudolf Gahl- on the "History of Flotation at Inspiration," and by David Cole on "The Advent of Flotation in the Morenci District." It is not within the province of this article to attempt an answer to the various issues raised in regard to the theory, or to defend the one advanced by me a year ago. But since discussion usually benefits the profession, a reply will be made to some of the statements made by the last-named writers. COMPARATIVE SENSITIVENESS AND ATTENDANCE Concerning 'the article, "Flotation Concentration at Anaconda, Mont.," by Laist and Wiggin, a little explanation is in order. It should be stated that; with the exception of about 24 days at the end of the testing 'period, the Callow experimental plant at Anaconda was not run under my direction. This perhaps accounts for some of the conclusions drawn on page 562 of the descriptive paper. The conclusion that the use of acid seems to be of considerable advantage, calls, for some comment. While the tests conducted by the Anaconda Copper Co. do show acid to be, of considerable benefit, this is a consequence of using acid sludge as a flotation agent. My belief has always been that the Anaconda

Jan 2, 1917

By P. D. Merica, H. Scott, R. G. Waltenberg

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903—1911 by A. Wilm1,2 and have been described by him and by others. 3, 4,5.6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from tempera-

Jan 1, 1921

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923