Search Documents

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By W. Hume-Rothery

IN recent interesting papers,1,2 Bardos et al. have described ternary Laves phases of the type A2(BsSi) and A4(B5Si3) where A = titanium vanadium, niobium, and so forth, and B = manganese, iron, cobalt, or nickel; other more complex formulae have also been established. In these phases, silicon plays the part of the smaller B atom of a Laves phase AB2, and the interatomic distances show that the effec- tive silicon radii lie between 1.16 and 1.21Å, and are thus very much smaller than the metallic radius of silicon for CN = 12. It does not seem to have been pointed out that these small atomic radii are almost the sape as the normal covalent radius of silicon (1.174Å). If, therefore, silicon acts as an acceptor of electrons as suggested by Bardos et al.,1 it appears to do so, not by the building up of a negatively charged silicon ion which would be large, but by the formation of what are very nearly or may be actually normal covalent bonds. Since a covalent bond contains two electrons, its formation would reduce the number of electrons available for bonding in other parts of the structure, and in this way the effect of silicon in stabilizing the o phase at high electron concentrations might be understood.

Jan 1, 1965

By Alan Stanley

THE Maclntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.1 Pigment plant production demands that the MacIntyre mill produce a 44.7 pct. TiO2 ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the Maclntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from one level to the next.. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the, physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO2 has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO2 has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the Maclntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO2 was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiO2 a constant gravity would invariably be obtained, and as the TiO2 value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct TiO2 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO2 value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO2 and as the specific gravity increased the trend was for the TiO2 assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. [ ] Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1952

By P. H. Mell

THE little village, from which this formation receives its name, is situated on a bluff of the Alabama River, 175 feet above water level. This bluff is a portion of high table land that begins in the western portion of Choctaw and extends through Clarke and Monroe counties. We find points on this ridge more than 100 feet higher than Tuscaloosa, and nearly as high as the Tennessee River at Tuscumbia. Through this the Alabama River cuts its way, exposing a beautiful cross-section of the strata, of which the accompanying sketch may give some idea. The fossils are found about 75 feet below the surface and 100 feet above the level of the river. There are seven distinct strata. 1. The lowest, extending from the water's edge up the bluff 80 feet, is a soft calcareous rock containing about 15 per cent. of carbonate of lime, with occasional specks of mica. In this a few Ostrea, Turritellce, and Flustrce were found, but so friable as to fall to pieces when handled. 2. Next comes a stratum varying from 2 to 8 feet, consisting of

Jan 1, 1880

By H. S. Munroe

To those familiar with ore-dressing practice, it is hardly necessary to dwell upon the importance of the jig. Within its proper sphere no substitute has been found that does the work as well or as cheaply. Its capacity is large, it requires but little attention, and the losses are small. In one form or another, it is the principal machine used in the concentration of low-grade ores, and for the separation of one metallic mineral from another; and it is almost the only machine used for the purification of coal. The present paper is a study of the action of the jig in the light of results obtained in the Lake Superior copper mills, ad at the St. Joseph Lead Co.'s dressing-works, in Missouri; and a description of experiments undertaken with the view of reproducing and isolating the conditions of jigging, in order to develop the laws which underlie the process. There are two recognized systems of jigging, the English and the Continental or German. The English system is a development of the hand-jigging formerly employed in Cornwall and other metalliferous districts of England, and introduced by English miners to this country. In this method the crushed ore, coarse and fine together, is first jigged oh a

Jan 1, 1889

By Herbert Clark Hoover, Lou Henry Hoover

MANY persons hold the opinion that the metal industries are fortuitous and that the occupation is one of sordid toil, and altogether a kind of business requiring not so much skill as labour. But as for myself, when I reflect carefully upon its special points one by one, it appears to be far otherwise. For a miner must have the greatest skill in his work, that he may know first of all what mountain or hill, what valley or plain, can be prospected most profitably, or what he should leave alone ; moreover, he must understand the veins, stringers1 and seams in the rocks2. Then he must be thoroughly familiar with the many and varied species of earths, juices3, gems, stones, marbles, rocks, metals, and compounds4. He must also have a

Jan 1, 1950

By J. J. Rutledge

I. Description of the Clinton Ores and Associated Rocks. The Clinton rocks in Stone valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.' A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the upper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Jan 1, 1910

By L. A. Willey

IN 1953, a method for filtering a liquid phase from solid phases while in equilibrium at elevated temperatures was devised at the Alcoa Aluminum Research Laboratories. Since then, it has been applied to the investigation of liquid-solid equilibrium in metallic systems. In application, the method simplifies the centrifuge filt.ration procedure as developed by Scheil and described by Gebhardt Fig. 1 shows a sketch of the filtering apparatus located within a thermal analysis furnace. It consists of a stainless steel filter crucible A, into the bottom of which a porous carbon filter disk B, 1 3/4 in. diam by 1/4 in. thick, is sealed to the shoulder and rim with carbonaceous cement. The base of the filter crucible, machined to an angle, fits into a tapered seat at the mouth of a stainless steel vacuum chamber C. A connecting tube from the vacuum chamber to a vacuum line also serves as a means for supporting the apparatus from the base of the furnace. An alundum crucible D of 25 ml capacity is placed with- in the vacuum chamber below the filter for collecting the filtrate. Two thermocouples E, in stainless steel protection tubes, which extend from 1/16 to in. above the center of the filter, are mounted on the rim of the filter crucible. One thermocouple is used in differential connection with the furnace control thermocouple to regulate rates of heating and cooling. The other serves as a means for recording the temperature of the alloy prior to filtering. A suitable mold coating is used on exposed surfaces of stainless steel parts to guard against attack upon these parts as well as to avoid contamination of the alloy samples. A mold wash prepared from precipitated CaCO, is suitable for aluminum alloys. The porous carbon for the filter disks and the carbonaceous cement, grade 200 (graphite base), were obtained from the National Carbon Co. Porous car-bon, grade Nos. 10 to 60, has been employed. Grade No. 40, however, appeared to give the optimum advantages in operation. In operation, an alloy sample is remelted and heated to about 50°C above its liquidus temperature. At the same time, the filter apparatus is preheated to about the same temperature. The alloy then is cast into the filter crucible.

Jan 1, 1957

By W. F. Netzeband

Jan 1, 1927

By Robert Linton

Tats paper deals with work that has been carried on for over three years by the management and staff of the North Butte Mining Co. in an effort to standardize mining methods, to eliminate lost motion in the operating organization, and to improve the efficiency of the individual workman. Naturally, much of this work is an adaptation of ideas suggested by other mining operations or by practice in manufacturing and other productive industries. The studies, however, have developed some features that it is believed are new. Both new and adapted features are given in detail. The normal capacity of the North Butte mines is about 2000 tons per. day. Hoisting is done principally through the Granite Mountain shaft, which is 3740 ft. (1140 m.) deep and equipped with an electric hoist capable of hoisting 200 tons per hour from a depth of 4000 ft. (1219 m.). The lowest stoping level is the 3400-ft. The Granite Mountain shaft is connected with the Speculator shaft, about 850 ft. (259 m.) south, and with the Gem, about 1150 ft. (350 m.) east, which are 3000 (914.4 m.) and 2000 ft. (609.6 m.). deep, respectively. These two shafts are equipped with reversible fans for ventilation. The Speculator has a; steam hoist with a capacity of 150 tons per hour from the 3000-ft. level. The Granite Mountain shaft is concrete lined from the 1600-ft. to below the 3000-ft. level and gunited with cement from the 1600-ft. level to the surface. Sections of the Speculator shaft with a total combined length of 500 ft. (152.4 m.) are also concreted. There are approximately 36 miles (58 km.) of drifts and crosscuts in the mine, in which there are 15.2 miles (24.5 km.) of track. At normal capacity, about 75 stoping faces, 20 raises, and 30 sill development faces are working. Stoping is usually by the standard square-set method. Where the size of the oreshoot and character of. the walls permit, the rill (or cut-and-fill) system is employed.

Jan 8, 1920

By A. H. Daane, R. L. Myklebust

The yttrium-manganese system has been investigated by thermal, metallographic, and X-ray diffraction methods. There are three intermetallic compounds present: YMn2 which melts congruently, YMn4, which undergoes syntectic decomposition, and YMn,, which undergoes peritectic decomposition. The compound YMn4 is ferromagnetic at room temperature with a Curie temperature of 214°C. There are eutectics at 25.2, 60.9, and 82.0 wt pct Mn which melt at 878°, 1100°, and 1075°C, respectively. Crys-tallographic data are given for YMn4, and YMn12 . The terminal solid solubilities are low. In a general program of study of yttrium metal in this laboratory some alloy systems of this metal with elements of the first transition period have been examined. This work was originally instigated by experiences in cladding yttrium with jackets of some protective metals such as Inconel for high-temperature service in air.' In some cases a low-melting phase was observed to form between the Inconel and the yttrium resulting in failure of the samples. In characterizing this reaction, a survey was made of the systems of yttrium with chromium, manganese, iron and nickel,, and it was found that a eutectic was formed between these metals and yttrium on the yttrium-rich side of the system. This present study of the Y-Mn system was carried out to examine in more detail the alloying nature of yttrium, and to correlate trends that have been observed in previous related studies. It was observed by Voge13 that in the systems of lanthanum, cerium, and praseodymium with each of the metals in the first transition series, the tendency to form compounds diminished in the order nickel, cobalt, and iron while no compounds were formed with manganese, chromium, or titanium. Beaudry and Daane4 observed a similar behavior in the systems of yttrium with some members of the first transition series except that the tendency for compound formation was greater. Both the Y-Ti5 and Y-Cra systems consist of simple eutectics, while in the Y-Fe,7 Y-CO, and Y-Ni4 systems, there are four, eight, and nine compounds, respectively. In addition to the above trends, the similar atomic radii and electronegativities of yttrium and thorium invite a comparison between their alloying behaviors with a common element such as manganese. In crys- tallographic studies, Florio et al.' have identified three intermediate phases in this system which are ThMn2, Th6Mn23, and ThMn,,. Gschneidner and Waber10 have examined published information on alloy systems of the rare-earth metals and have correlated this information with current alloying theory. From their study, they predicted that the Y-Mn system would contain one intermetallic compound. On the basis of this prediction, the trend in the alloying behavior of yttrium with the elements of the first transition series and the alloying behavior of thorium with manganese, one might expect from one to three intermetallic compounds to form in the Y-Mn system. A consideration of Hume-Rothery's rules of alloying based on size-factor, electronegativity, and valency suggested a small terminal solubility and possible compound formation. The present study was undertaken to confirm these predictions of low terminal solid solubility and compound formation and to establish the general alloying behavior of yttrium with manganese. EXPERIMENTAL Materials. The manganese used in this investigation was obtained from the Foote Mineral Co. as electrolytic plates of 99.9 pct stated purity; the yttrium metal was prepared in this laboratory. Table I gives the analyses of these materials. For the solubility studies at the yttrium-rich end of the alloy system, distilled yttrium, whose major impurity was 200 ppm Ti, was used. Preparation of Alloys. The alloys were formed by comelting the two metals in an are-melting furnace under an atmosphere of argon. The buttons thus formed were inverted and remelted three to five times to promote homogeneity. Due to the high vapor pressure of manganese, it was assumed that the weight lost during are-melting was all manganese. This assumption was based on the very good agreement observed between calculated compositions and chemical analyses of several alloys. The compositions of the dilute alloys used for solid solu-

Jan 1, 1962

By K. E. Brown, F. W. Jessen

By utilizing an 8,000-ft experimental field well equipped with 10 gas-lift valves and 10 Maihak pressure recorders, gas-lift tests were conducted with port sizes ranging from 5/16 through I in. The well was equipped to provide accurate means of measuring surface pressures, temperatures, quantity of injection gas and fluid production. The tests were conducted in 2%-in. OD tubing, and the well was making 95 per cent water. A complete evaluation of gas-lift-valve port sizes shows the relationship of per cent recovery, gas-liquid ratios, minimum pressure created at the operating valve and horsepower requirements for each port. The length of time necessary for the fluid in the tubing to reach equilib.rium conditions after each cycle was recorded. Fallback of fluid at depths of 477, 969, 1,685, 2,493 and 4,290 ft was noted. For each port size, pressure loads of 2.50, 300, 350, 400 and 450 psi were lifted with a valve operating at approximately 550 psi at 6,000 ft. Gas-liquid ratios for each load were varied from excess gas to a gas volume per cycle whereby the load failed to reach the surface. Numerous curves are presented in evaluating the accumulated dara. The results show a 1-in. port to be the most efficient under all conditions. The production of intermittent liquid slugs against different-sized surface chokes was evaluated. These tests were conducted from a 7/16-in. ported valve at 4,072 ft. Tests indicate that, when possible, a %-in. in diameter choke or larger should be used at the surface. In the past few years most of the advancement in gas-lift operations has been made in continuous-flow operations. Yet, it is estimated that at least 70 per cent of the wells on gas lift in the United States are of the intermittent type. Since the term "slug flow" is sometimes used in both intermittent- and continuous-flow operations, it would be well to distinguish between the two types of flow. Continuous-flow gas lift is defined as a method whereby the fluids are produced at a continuous rate at the surface. This generally requires a continuous injection of gas through a surface choke; however, various other control devices sometimes are installed to eliminate freezing, to shut-off gas during natural flow periods, etc. The actual flow of fluids in the tubing may be of the slug type (one of many flow patterns known to exist in continuous flow). Intermittent flow is defined as a method of gas lift whereby the liquid is produced in separate piston-type slugs. Perhaps this type of flow could best be thought of as a ballistic-type flow where the liquid leaves bottom as a piston, propelled by a slug of expanding gas. Gas generally is injected through some type of control at the surface at predetermined intervals. However, the valve may have characteristics whereby gas can be injected through a small choke and still result in a ballistic-type flow. The purpose of the experimental work was to evaluate the most efficient port size to be used on the operating valve for the ballistic type of lift and, in addition, to establish the importance of utilizing a surface choke large enough to allow slugs to be produced without detrimental effects. This work is part of a compre- hensive study of both intermittent-and continuous-flow gas lift, representing a joint project conducted by the Ohio Oil Co., the Sun Oil Co., Otis Engineering Corp, and The U. of Texas. The problem of evaluating port sizes has been given little previous attention. Some work undoubtedly has been done which has not been published to date. Some tests were conducted when the wireline, mechanically-opened valve (Nixon) first came on the market. This valve was capable of utilizing full tubing area as its port size. It is known that this was a very efficient valve, but to the authors' knowledge the results of tests have never been published. EXPERIMENTAL EQUIPMENT These tests were conducted on an actual field well, the Ohio-Sun Unit Well No. 2-E, in the North Markham-North Bay City field, Matagorda County, Tex. The well incorporated 23/8-in. OD tubing and produced 95 per cent water. Since the running of equipment was to be quite elaborate and expensive, a well was selected in which both intermittent- and continuous-flow tests could be conducted. This particular well was capable of producing in excess of 1,000 B/D of liquid (95 per cent salt water), yet with a 3/64-in. in diameter bottom-hole choke, production was controlled to 82 B/D. Most of the intermittent tests were conducted at this low rate. Figs. 1 and 2 show all the surface and down-hole equipment. As can be seen, every attempt was made to insure that ample equipment was available for reliable testing procedures. Fig. 1 shows the surface testing equipment. The input gas was controlled first by a regulator, then

By J. J. Frawley, W. J. Childs

The dynamic nucleation of supercooled bismuth and Bi-Sn alloys has been studied over a frequency range of 15 to 20,000 cps. For low-frequency vibration, a minimum vibrational energy was required for enhancement of nucleation. Above this critical energy, the dynamic supercooling was less than static supercooling showing that vibration promoted nucleation. The amount of dynamic supercooling continued to decrease with increasing vibrational energy until a minimum or threshold value was reached. This minimum value of supercooling for nucleation remained constant joy all further increases in vibrational energy. For higher frequencies, similar results were observed. This behavior has been related to the necessity of cavitation for dynamic nucleation. When a liquid is cooled to a temperature below its equilibrium melting point, the solid phase is more thermodynamically stable. However, for solidification to occur, a two-step process, nucleation and subsequent growth of the solid phase, must occur. When a liquid is supercooled, that is cooled below the equilibrium melting point, the controlling process for solidification to begin is the rate of nucleation. Once nucleation has occurred, the solidification process is controlled by the rate of growth. Nucleation can be induced by two factors: either by a catalyst or by the use of mechanical shock. Numerous investigators1-4 have studied the effect of nucleation catalysis but much less systematic study has been made of nucleation by mechanical shock waves. The influence of vibrations on grain size in castings and ingots has been studied by many authors but no clear understanding of the mechanism or accurate prediction of the effect has been presented.5 It would be intuitively expected that the further the departure from equilibrium (i.e., the greater the supercooling), the easier it would be to induce nucleation. This has been quantitatively demonstrated both by walker6 and later by Stuhr,7 that the greater the degree of supercooling the easier it is to nucleate by a shock wave. Stuhr also attempted to obtain the mechanical energy required for nucleation of bismuth as a function of supercooling. He vibrated a crucible containing supercooled metal at low frequencies and various amplitudes and noted the corresponding dynamic supercooling obtained. The amount of supercooling was inversely proportional to the mechanical energy applied. Limitation of his experiment was the problem of the confinement of the liquid in the crucible without splashing and minimizing other unwanted modes of vibration. Tiller et al.8,9 did similar work on tin and Sn-Pb alloys using an electromagnetic stirring device. Their conclusions were that the magnitude of the magnetic field strength did not affect the amount of undercooling at which nucleation was initiated. While conclusive experimental results have been lacking to explain this effect of mechanical vibration on inducing nucleation, a number of theories have been proposed. Two of these theories are discussed below. 1) The Change in Melting:- Point Locally Due to the Change in Pressure (Clapeyron Equation). According to Vonnegut10 the most plausible explanation for the nucleation of a supercooled melt by cavitation is the effect of changing the melting point by a change in pressure. For materials where the volume decreases on solidification, an increase in pressure raises the melting point; for materials which expand on solidification, the melting point is raised for a decrease in pressure, i.e., rarefaction. Using the Clapeyron equation, the melting point of a metal can be calculated as a function of pressure. If it is assumed that the equation can also be used to calculate the temperature of nucleation of a supercooled melt as a function of pressure (i.e., the temperature of heterogeneous nucleation will increase with pressure at the same rate as the melting point), the amount of supercooling required for nucleation will be constant at all pressures as shown in Fig. 1. It is obvious that an isothermal change which results in an increase in melting point results in an equal increase in supercooling. This increase in supercooling may now be sufficient for nucleation. A pressure of 80,000 atm was calculated, using the Clapeyron equation, as the pressure required to increase the temperature of nucleation of nickel by 200°C. According to Lord Rayleigh,11 this very large pressure could be generated for a very brief period of time by the collapse of a cavity. This pressure wave is radiated in all directions from the collapsed cavity. If the temperature of the melt is slightly below its equilibrium melting temperature at atmospheric pressure, stable growth can follow; that is, once nucleation occurs, growth becomes the main driving force of the solidification process. This proposal has been extended to water which expands on freezing by assuming that nucleation occurs during rarefaction following the pressure pulse. This negative pressure pulse should follow immediately after the positive pressure pulse with its magnitude approaching the critical tensile strength of the liquid. The negative pressure developed during this period would raise the melting point of water and thus promote nucleation. Hunt and jackson12 have suggested this for water. Similarly, it could be postulated that bismuth which also expands on freezing could be nucleated during the negative pressure pulse. 2) Nucleation by a High-pressure Phase. An extension of the Clapeyron equation to systems where density decreased on freezing at atmosphere pressure has been proposed by Hickling.13 The phase diagram for water initially shows the well-known decrease in

Jan 1, 1969

By J. S. Diller

In 1827, chromite was discovered near Baltimore by Isaac. Tyson, Jr., who initiated the mining of chrome ore and later (1845) the manufacture of chromium compounds in this country. From 1828 to about 1560 the United States, supplanting Russia, supplied chromite for most of the world. Chrome deposits were found also in California, and the Tyson Company shipped ore to Philadelphia by way of Cape Horn. In 1848, J. Lawrence Smith, an American in the employ of the Porte, discovered large bodies of chromite in Asia Minor. They were developed in 1865 and became the chief source of the world's supply for a number of gears. The discovery of the large high-grade bodies in New Caledonia., and later in Rhodesia, with other foreign sources, gives at present an abundant supply for all demands. For a number of years before the great war. the United States produced only a few hundred tons of chromite annually, for local use, but during the war the demand for domestic ore resulted in a production of more than 82,000 long tons of crude ore in 1918, and it was demonstrated that the United States has reserve deposits equal to a war demand of several years' duration. Now that the war is over, the country is con-serving its domestic supplies by employing higher-grade but cheaper ore from foreign countries.

Jan 9, 1919

By E. L. Jr. Spain

This study was undertaken primarily to determine the reasons for certain varia-tions in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates it some cases exhibited marked differences in specific gravity, crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents.

Jan 1, 1937

By B. W. Gandrud

WET-PROCESS coal-washing tables as we know them today have been in use in this country for approximately 25 years. The literature records only a few table installations worthy of note prior to adoption of the present-day differential-motion table. According to Phillips,' six Campbell bumping tables were being operated by the St. Bernard Coal Co., Earlington, Ky., in 1893. As late as 1923, according to Richardson, 72 such tables were in operation in the Rosedale washery of the Cambria Steel Co., at Johnstown, Pa. Bumping tables probably were not used to any considerable extent except in the plant at Earlington, and at two or three plants in Pennsylvania, but they may be considered as forerunners of the present-day coal-washing table. The transition from bumping tables to the type of tables now in use signalized a revolutionary change iii table design. The advantages of the new design over the old were so outstanding as to make its adoption inevitable. BUMPING TABLES Bumping tables, as the name implies, utilized a bumping action for conveying the refuse and discharging it over the refuse end. The tables were hung from rods attached to overhead supporting beams. A shaft and cam arrangement at one end of the table served as ,the actuating mechanism and imparted to the table an endwise, back-and-forth, swinging motion. A bumping block was fixed in the proper position at the shaft end, so that the table would strike against it at the end of each backward swing. The hanger rods or stirrups were so adjusted as to give the table a slight uphill slope toward the refuse end; that is, the end next to the driving mechanism. The feed box was near the upper end of the table and designed to spread the mixture of coal and water over the width of the table. Wash water was added a short distance below the feed box. With the table in motion and coal mixed with water being fed to it through the feed box, a certain amount of stratification took place, depositing heavy refuse at the bottom of the bed in contact with the surface of the table. Constant bumping and a certain amount of

Jan 1, 1943

By B. G. Klugh

In a paper before the Institute at Wilkes-Barre, Pa., June, 1911,' Mr. James Gayley discussed the application of this process to iron-bearing materials. The same author² described the results of operations at the plant at Birdsboro, Pa. The purpose of the present paper is to present further discussion of some techuical details involved in the operation of this plant, and of the theoretical and practical relations of this product to blast-furnace practice. Since Oct. 1, 1911, the Birdsboro plant has been in operation at the blast-furnace of the E. & G. Brooke Iron Co. The results have been highly satisfactory, although the material treated, being chiefly the flue-dust currently made by the furnace or taker] from the accumulated stock-pile, was excessively high, and yet not uniform, in carbon, so that the desirable control or regularity of the amount of fuel in the mixture treated could not be maintained. Nothing could more forcibly demonstrate the flexibility of the process than the fact that, under these conditions, the sinter produced was, in all cases, of excellent quality. The Dwight & Lloyd process, as such, slid its present highly-developed mechanical appliances were described by Mr. Gayley in the paper above mentioned. While the repetition of some particulars will be unavoidable in this paper, it will be confined to features bearing upon the metallurgical principles involved. According to the principle of the process, the finely-divided iron-bearing material to be sinterecl is intimately nlixed with

Jan 1, 1913

Jan 1, 1907

US 4,134,618-Method for restoring an underground reservoir subsequent to the solution mining of an ore body of uranium, copper, nickel, vanadium, molybdenum, silver, rhenium, or selenium. Clean water a cycled through the mined area, via the injection and production wells used during mining, at a flow rate sufficient to entrain residual dissolved solids. The solids are separated at the surface and disposed of, e g., in a deep disposal well, while clarified water is recycled C A. Kossack, assigned to Atlantic Richfield Co. Jan 16, 1979 4 pp. (299-5) Filed. 12-29-77 (865,646) US 4,155,982-In situ leaching of a subterranean uranium ore deposit The ore is leached with a dilute aqueous solution of ammonium bicarbonate containing a small amount of hydrogen peroxide in order first to convert tetravalent uranium in the ore to the hexavalent state and second to dissolve the hexavalent uranium preferentially to the other metals or elements commonly occurring In such ore The uranium- enriched leach liquor IS brought to the surface, and the uranium recovered by means of adsorption on a particulate ion exchange resin, elution with an acid, and treatment with ammonia to precipitate relatively pure ammonium diuranate. G G. Hunkin, T P. Fife, and J R Stano, assigned to Wyoming Mineral Corp. May 22, 1979. 13 pp (423-7). Filed: 10- 9-74 (51 3,445). Same: Canadian 1,027,849, dated Mar. 14, 1978. US 4,157,847-In the mining of sulfur by the Frasch process hot water accumulating above subterranean sulfur from previous mining operations is recycled downward to contact and heat additional solid subterranean sulfur. Advantageously, pressurized and superheated drive water from above ground is commingled with the underground water to raise its temperature before it is recycled downward R. L Williams, R L Latiolais, J. L Gabriel, and R. L Bouis, assigned to Freeport Minerals Co June 12, 1979. 13 pp (299- 6) Filed 7-28-77 (81 9,879). US 4,158,76%1n this method for determining the uranium content of a solution obtained in the solution mining of an underground uranium ore deposit, the intensity of gamma radiation from the Th-234 daughter of U-238 emitted by the solution is determined as it impinges on a scintillator after being passed successively through filter foils of a ytterbium- tin alloy, a lutecium-tin alloy, and a hafnium-zirconium alloy This scintillation is evaluated as a measure of the uranium content To assure that the uranium-thorium conversion has reached a stable state, the measurement should be made about three months after the uranium solution has been produced R C Smith, assigned to Westinghouse Electric Corp. June 19, 1979 11 pp. (250-255). Filed. 10-20-77 (843,770).

Jan 1, 1980

By J. F. Evers, S. Sadiq, F. W. Preston, G. W. Swift

Proper scaling of unsteady-state flow in laboratory gas reservoir models can be achieved if the permeability/fractional porosity ratio is less than 0.5 md. Porous media meeting this specification can be obtained from mixtures of sand and Portland cement provided (1) the water/cement ratio is in the range of 0.35 to 0.40, (2) the sand/cement ratio is in the range of 1/1 to 2/1, (3) the sand grain size is in the range of 48-100 to 18-28 mesh, (4) the mortar curing time is 7 days or more and (5) the cured mortar is dried under vacuum to reduce the temperature level employed during the drying process. The areal homogeneity of the mortars tested is reasonably good, although significant trends in vertical permeability were noted. The Klinkenberg and non-Darcy coefficients of mortar are such that proper scaling of these effects in the laboratory model could be expected. INTRODUCTION A long term deliverability prediction for a gas well is generally based on data determined from flow tests that are of short duration relative to the producing life of the well. These data, together with an estimate of gas reserves in place, form the basis for establishing the parameters of the mathematical model used to predict performance at future times. Results obtained from a mathematical model represent only an interpretation of the physical process being modeled. Experimental verification of the production process from discovery to abandonment is needed where production occurs under carefully controlled conditions. Ideally, one might consider such an experiment to be conducted in the field. Even if the cost of such an experiment could be justified, the time required would make it impractical to consider. However, if the time scaling problem could be handled properly, an experimental model of the gas reservoir production process could provide the necessary data to study the mechanisms of the production process in a reasonable time period. An experimental model has been designed and constructed using the data of this study as a basis. The model reservoir system consists of one producing well located at the center of a right-circular cylinder of porous material. Ten to 15 observation wells are located at strategic offset positions from the producing well. These wells, and the producing well, are fitted with pressure transducers so that the pressure-time history can be recorded at various radial and azimuthal positions in the drainage area during the entire production life of the system. Time is scaled in the model so that the time required to produce gas from discovery pressure to abandonment pressure is about 2 hours. This compares with a 20-year producing life in the model's field counterpart and gives a time scale factor of approximately 1:100,000. DESIGN CRITERIA To establish design criteria for the experimental model, the reservoir is considered to be a finite right-circular cylinder of radius rr, and height h with a producing well of radius rw located at the center and completed through the producing formation. This reservoir consists of a porous medium which has a uniform permeability k and gas porosity and the gas contained in the reservoir has density p, viscosity µ and molecular weight M. Initially, the pressure at all points within the reservoir is uniform at po. and the reservoir temperature is T. Since the reservoir production process has been demonstrated to occur in two distinct transient modes for either Darcy or non-Darcy flow,l it is