Search Documents

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By Arthur Phillips

THE normal method of preparing metallic alloys for commercial use involves the preparation of a melt containing the given components in the chosen proportions and allowing the homogeneous liquid mass to solidify in a mold of the desired form. The solidification is frequently accompanied by a segregation of the alloying elements in different parts of the casting. When the segregation is occasioned primarily by marked differences in density of the solid and liquid phases, it is termed "gravity" segregation. When the segregation conforms to a. selective freezing in harmony with the teachings of the equilibrium diagram of the alloy system-i.e., the lower melting phases are concentrated in the regions of the casting last to freeze-it is often referred to as " normal" segrega-tion. However, in many cases the lower-melting part of the system is concentrated in the parts of the casting first to freeze and the result in this case is termed "inverse" segregation. To complete the. terminology of the subject, normal segregation in a single phase is usually called "coring" and the word will be used in that sense in this paper. Inverse segregation, particularly when the liquid phase is exuded or sweated out on the surface of the casting, is sometimes called "location." Unfortunately, some ambiguity has arisen from the use of this term and it is perhaps advisable to confine its use to the dictionary definition; namely, "The separation of two phases by heat sufficient to melt one but not the other." The gravity and normal types of segregation are both well understood and to some extent are controllable by taking advantage of the most favorable cooling rate for a given casting condition. Inverse segregation has received considerable attention from several investigators- but none of the theories offered seem to account in a convincing way for the many examples of this type. The observations made in the present work on segregation in single crystals, and in some other castings, tend to support one theory of the mechanism of inverse segregation and definitely to

Jan 1, 1937

By G. T. Jackson

PROPERTY AND LOCATION THE Alaska Gastineau Mining Co.'s mine is located at Perseverance, about 4 mi. east of Juneau, Alaska. Its property consists of a group of claims, the lode system traversing these claims for a distance of 11,000 ft. (3352 in.). It is shown in Fig. 1. FIG. 1.-ALASKA GASTINEAU MINING CO.'S PROPERTY NEAR JUNEAU. The ore deposits occur in what is known as the Juneau gold belt. This gold belt can be traced for about 50 mi. northwest of Juneau and 40 mi. southeast. It consists of a single band, several hundred feet wide, in which stringers and veins of quartz, carrying gold, occur in a slate formation near its contact with some altered volcanic rock known as greenstone.

Jan 9, 1919

By Charles R. Austiuon, Carll H. Samans

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By Carll H. Samans, Charles R. Austiuon

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

NEW MEMBERS The following list comprises the names of those persons who became members during the period July 10, 1919, to August 10, 1919. BALL, C. LEONARD.. Cons. Engr., Suffern Co., Inc., 135 Broadway, New York, N. Y. BARRY, CHARLES W Box 502, Idaho Springs, Colo. BATTLE, JOEL ALLAN, JR., Min. Engr., U.S. Bureau of Mines, Room 2114, Interior Bldg., Washington., D. C. BEER, GUIDO, Compagnia. Italian, Dir Bronzi Speciali, C. I., B. S. La Direzione, Italy. BITLER, WILLIAM F., Management of Coal Properties, The Provident Life & Trust Co. of Philadelphia, 409 Chestnut St., Philadelphia, Pa. BLOOM, SETH W., Chief Engr,, Northwestern Min. & Exchange Co., 130 E. Sribner Ave., Du Bois, Pa. BOYDELL, W. Guy B., Min. Engr., Tul Mi Chung Mine, Care Seoul Min. Co. Whang Hai Do, Chosen. Korea. BRYAN, RUSSELL R.., Met., Sunnyside Min. & Mill. Co., Eureka, San Juan Co., Colo. CHIAPELLA, STEPHEN EUGENE 323 W. 30th St., Los Angeles, Cal. CONWAY, EDMUND JOHN, Exploration Engr., Granhy Consolidated Min., Smelt & Power Co., Ltd., Anyox, B. C., Canada. DEMOREST, DANA J Prof. of Met., The Ohio State Univ., Columbus, Ohio. EIDEMILLER, H. N., Geol., Benjamin C. Neely, Min. Lands & Leases, Crystal Falls, Mich.

Jan 9, 1919

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By Charles G. Yale

(San Francisco Meeting, October, 1911.) A FEW years ago somebody connected with one of those self-constituted bodies of unofficial character, like a Chamber of Commerce, Board of Trade, or State Development Board, started a catch-phrase referring to California as " The Land of Sunshine, Fruit, and Flowers," and the railroad magazines and folders keep it steadily in use, working day and night. Yet it altogether ignores the substance which brought the State into the Union, which peopled it, and which made it famous through-out the world. You ladies and gentlemen who have come from what we here call "the East," have in your own States, no matter which one, sunshine, fruit, and flowers. But your Eastern States, having these things as we do, have not the gold that we do. Therefore, the old designation of "The Golden State," applied to California, should be revived, as being the most distinctive term. It is worthy of remembrance, too, that during the dark days of the civil war this State handed over $172,000,000 in yellow gold, and saved the credit of the nation. Gold-mining has been carried on in California since " The days of old, The days of gold, The days of 49," and it still continues. Since that historic year, and up to the end of 1910, the State has produced, in gold alone, $1,530,214,468. Since 1792 the entire United States production of gold has been $8,261,573,500, so that the single State of California has, in that period, produced within $201,144,564 of one-half of all the gold from Alaska, Arizona, Colorado, Idaho, Montana, Nevada, New Mexico, Oregon, South Dakota, Utah, Washington, and the Southern and scattering States. In other words, all the other 25 gold-producing States of the United States combined

Mar 1, 1912

By Louis D. Huntoon

After the completion, in 1905, of the Hammond Mining and Metallurgical Laboratory of the Sheffield Scientific School, Yale University, it became necessary to secure and assay a large assortment of ore-samples, and to arrange the results in such a manner as to admit of use with the least amount of work on the part of the instructor. At first, pulp-samples, together with their respective assays, were secured from the mines, smelters, and public aesayers, but this practice did not prove satisfactory. It was not only difficult to secure a suffciently large supply of material, but it was also impossible to secure the proper assortment required for instructing students. It involved considerable work for the donors to select the samples and furnish a record of the assays, and also for the instructors to examine each pulp and determine its character. Some of the samples did not contain a sufficient quantity of pulp for the student to check his work in case his first assay did not correspond to the record. In order to increase the number of samples and to vary the character of the material, pulp-samples were later mixed with barren rock and with sulphides, but this method also was unsatisfactory and has been discontinued. At present, small lots of ore are secured by gift or purchase from engineers, public assayers, and the managers of mines, mills, and smelters. These lots weigh from 10 to 100 lb. each, and are rarely finer than 0.25 in. in size. The larger samples permit of a careful study by the instructor in order to determine the best method of assaying to be followed. In universities in which assaying is taught the record of the samples should fulfill the following requirements:

Jan 1, 1910

[†AARONSON, ALFRED E., Vice-Pres., Mid-Co. Petroleum Co., Mid-Co. Bldg. Tulsa, Okla. &apos;18 ABADIE, EMILE R., Min. Engr Address wanted. &apos;76 ¦ABADILLA, QUIRICO A. Geol. Dept. Cia. Mexicans de Petroleo "El Aguila," S. A., Edifico "El Aguila," Esq., Calles Aurora y Comercio,] [ ]

Jan 1, 1925

NEW MEMBERS The following list comprises the names of those persons who became members during the period May 10 to June 10, 1914. Members ABE, ASAKA, Chief Min. Engr., Yamagano Gold Mine, Satsuma-Gori, Satsuma, Japan. ANDERSON, FRANK M., Geol Cartagena Refining Co., Cartagena, Colombia, S. A. BACON, MAURICE W., Genl. Mgr Stewart Mining Co. Butte, Mont. BACON, RAYMOND F., Chem Director, Mellon Institute, Pittsburg, Pa. BAKER, HAMILTON WALLACE, Min. Engr Fernley, Nev. VON BAYER, AUGUST HECTOR, Supt Kentucky Solvay, Coke Co., Ashland, Ky. BISHOP, WHEELER SCOTT, Research Chem Care Braden Copper Co., Rancagua, Chile, S. A. BOWEN, CHARLES GILMAN, Timekeeper 208 School St., Grass Valley, Cal. BOYER, SAMUEL L., Mine Operator, Mgr., Mike. Horse Min. Co., W. 2808 Boone Ave., Spokane. Wash.

Jan 7, 1914

By P. S. Miller, S. H. Ash

EXTENSIVE and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past 10 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the succeeding face, constituting a round.1 Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons1 tunneling is more hazardous than mining in any branch of the mineral industry, On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One of these is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. THE DELAWARE AQUEDUCT The new Delaware aqueduct is a Manhattan project of some magnitude; when completed, it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1942

By B. S. Hickman

Using primarily quantitative single crystal X-ray techniques studies have been made of the precipitation of the metastable w phase in alloys of titanium with Mo, Mn, Fe, Cr, and Nb. It is shown that, in agreement with earlier work on the Ti-V system, the composition of the w phase during aging approaches a constant; the value varies from one system to another in a systematic manner with the electron concentmtion. Results relevant to the mechanism of w precipitation during quenching and during aging are presented and discussed. Results are presented to confirm that the w phase is coherent and the nzorphology of the Necipitates is described and discussed. PRECIPITATION of the metastable w phase in alloys of titanium is of interest because of its severe embrittling effect and also because of the enhancement of the superconducting properties which accompanies precipitation.1 The general features of w phase precipitation have been discussed by cuillan and by Bagaratskii et d3 The work described in this paper forms part of a general study of w phase precipitation which was undertaken to elucidate various unknown or controversial features of the process, namely: i) What is the mechanism of formation of the phase ii) How does its composition, morphology, volume fraction, and particle size vary with the type and content of the alloying element and with the heat treatment conditions? iii) What is the relation between the w phase and the equilibrium a phase? In a previous paper4 the results of a detailed study of w phase in Ti-V alloys were presented. It was shown that: U During aging the composition of the w phase approached a saturation value of 13.5 to 14.0 at. pct V. ii) w precipitated as cube shaped particles and once precipitation was complete, particle coarsening did not occur. iii) a phase formed initially by direct conversion of w-phase precipitates. In this paper similar measurements are reported on Ti-Mo alloys and some more limited data given on the Ti-Cr, Ti-Fe, Ti-Mn, and Ti-Nb systems. The results i.1 the six systems are then compared. It has been shown previously by electron microscopy that the w precipitates as ellipsoids in both the Ti-Nb system,&apos; and in i-o.&apos; Blackburn and williamsz3 have reported the precipitates in Ti-Fe, Ti-Cr, and Ti-Mn are cubic, i.e., similar to the Ti-V system.476 EXPERIMENTAL METHODS 1) Specimen Preparation. Samples of the compositions shown in Table I were prepared by arc melting. High purity electron beam zone refined titanium (Materials Research Corporation Grade I—total impurity content =250 ppm) was used; the other source materials are given in the table. A commercial Ti-8 wt pct Mn alloy was used for studies of this system. After homogenization the materials were rolled or cut into strip approximately 1/4 in. by 2 in.; the strip was then heated at temperatures of 1200" to 1300°C for several hours by passage of a direct current through the strip in an ultra high vacuum system (<10-torr) and then quenched by admitting high purity helium and switching off the current. This treatment resulted in crystals up to 2 in. by 2 in. by A in., almost all of which had a [100] direction nearly perpendicular to the plane of the strip. The crystals were cut from the strip by spark machining and their composition checked by lattice parameter measurements supported by chemical analysis. 2) X-Ray Diffraction Methods. Lattice parameter measurements were made using a modification of the single crystal spectrometer described by ond. In this technique the crystal angles for reflection on either side of a highly collimated primary beam are measured. Generally the 400 CuK, or the 400 CuKp reflections of the bcc lattice were used. In the as-quenched crystals a precision of 1 in 105 was obtained, but due to line broadening the parameters in aged materials could only be measured to 1 in lo4. This accuracy was, however, quite adequate for the purposes of these experiments and enabled the composition of the p phase to be obtained to 10.1 pct in all systems except Ti-Nb where the lattice parameter change with composition is very small. The precipitation and growth of the w phase was examined using a single crystal goniometer attached to a Phillips diffractometer. The relative intensities and line shapes of b-phase and w-phase reflections

Jan 1, 1970

By Elizabeth L. Robinson

INTRODUCTION The financial structure of the mining industry has changed strikingly over the last thirty years. The changes that have taken place in the last ten years include both the acceleration of adverse trends in familiar balance sheet numbers and ratios, and the subtle but extensive increase in the complexity and diversity of funding sources, both on and off the balance sheet. The objectives of this paper are: 1. to briefly trace the evolution of trends in the mining industry&apos;s financial structure; 2. to focus in more detail on changes in the last decade; and 3. to analyze those trends both within the framework of capital structure theory, and in the context of changes in business and economic conditions. This survey focuses primarily on the mining companies listed on the major U.S. stock exchanges, since financial data for these firms are readily available. The producers of minerals are a diverse lot, however, and the quantitative data on "the mineral industry" as characterized in this survey fails to encompass the financial arrangements for the bulk of production worldwide, whether owned by governments or private-sector enterprises. Even large portions of the U.S. minerals industry - subsidiaries of still larger firms, medium-sized privately-held companies, and the small miners - were not included in the quantitative part of the analysis. THE EVOLUTION OF THE INDUSTRY&apos;S FINANCIAL STRUCTURE In the aftermath of the business failures of the Great Depression, most borrowers and lenders considered minimal debt on the balance sheet the soundest policy. By the 1950&apos;s, however, a body of literature was developing which demonstrated that the use of leverage could improve the value of the firm, given a corporate tax structure which allows interest, but not dividends, to be deducted from income. Optimal Capital Structure The objective of undertaking a new project is to improve the wealth of the current owners of the firm. If internally-generated funds are insufficient to allow growth at the desired rate, the company can raise funds either by issuing new equity, or by incurring debt. The most attractive source is the one which will provide the funds for the lowest cost. Both stockholders and lenders expect to receive compensation for use of their funds at a rate which reflects two things: (1) the return they could earn in alternative investments, and (2) the riskiness of the projected return. Factors which increase business risk include the variability of demand, sales prices and input prices, and "operating leverage", or the proportion of fixed to variable costs. In addition, from the investors&apos; point of view, the use of financial leverage concentrates risk onto the shareholders, because lenders enjoy a prior claim in the event of bankruptcy. So although financial leverage can increase a project&apos;s expected rate of return, and therefore, presumably, earnings per share, too much debt will be perceived as uncomfortably risky by equity investors, and have a negative effect on stock prices. In theory, then, there should be an optimal level of debt which the firm&apos;s managers should seek to obtain in its financial structure. The desirable proportion of debt should in general be lower for a firm with a higher inherent business risk. In addition to their own judgement, financial managers are sensitive to the attitudes of lenders, rating agencies, and investment bankers in setting financial targets (Scott and Johnson). In practice, financial structure will also depend upon the company&apos;s growth rate and level of profitability, and conditions in the capital markets at a given time.

Jan 1, 1985

By R. Philip Hammond

Monazite has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent—thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. Occurrence Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatite~ and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. Composition of Monazite As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium Table i.—Typical Analysis of a Monazite Sand (India). Per Cent Thorium oxide............................. 8.1 Cerium oxide.............................. 30.6 Lanthanum oxide........................... 15. 7 Neodymium oxide.......................... 10.5 Praseodymium oxide........................ 2. 9 Samarium oxide............................ 1.0 Europium. gadolinium, and terbium oxides.... 0.7 Yttrium oxide.............................. 0.4 Dysprosium, holmium, erbium. thulium, ytterbium. and lutecium oxides................. 0. 1 Silicon oxide............t................... 2.4 Calcium, aluminum, and iron oxides.......... 1.0 Uranium oxide............................. 0.3 Phosphorus pentoxide....................... 26. 2 a The values given for the rare earths following samarium are approximate. being based upon analyses of concentrated fractions derived from monazite. The composition given represents Travancore monazite carefully freed from other minerals. goup of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1948

By R. Philip Hammond

Monazite has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent—thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. Occurrence Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatite~ and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. Composition of Monazite As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium Table i.—Typical Analysis of a Monazite Sand (India). Per Cent Thorium oxide............................. 8.1 Cerium oxide.............................. 30.6 Lanthanum oxide........................... 15. 7 Neodymium oxide.......................... 10.5 Praseodymium oxide........................ 2. 9 Samarium oxide............................ 1.0 Europium. gadolinium, and terbium oxides.... 0.7 Yttrium oxide.............................. 0.4 Dysprosium, holmium, erbium. thulium, ytterbium. and lutecium oxides................. 0. 1 Silicon oxide............t................... 2.4 Calcium, aluminum, and iron oxides.......... 1.0 Uranium oxide............................. 0.3 Phosphorus pentoxide....................... 26. 2 a The values given for the rare earths following samarium are approximate. being based upon analyses of concentrated fractions derived from monazite. The composition given represents Travancore monazite carefully freed from other minerals. goup of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1948

By G. W. P. Rengstorff, R. B. Fischer

A study was made of the effect of impurities on the bend ductility of cast molybdenum. High purity molybdenum was repared by re-melting under high vacuum. The ductility of "transverse-grain" specimens indicated that intergranular brittleness decreased with an increase in purity of the metal. THE production of as-cast molybdenum with high ductility at room temperature would make working of the metal easier and increase the usefulness of the as-cast metal. Furthermore, a .knowledge of the factors that influence the ductility of as-cast molybdenum might be applied to the problem of making fusion weldments having satisfactory room-temperature ductility. Individual grains of commercial as-cast molybdenum are slightly ductile at room temperature. However, the presence of carbides at the grain boundaries may cause the metal to fracture in a brittle manner. This behavior has been discussed.&apos; The amount and distribution of the impurities in as-cast molybdenum would be expected, from previous research on the metal, to have considerable influence on its ductility. Some effects of oxygen and carbon on the mechanical behavior of the metal were discussed by Parke and Ham,2 Woodside,3 and Zappfe. Landgraf, and Worden.4 Parke and Ham2 found that, if a sufficient number of molybdenum oxide particles were present at the grain boundaries, the intergranular cohesion was reduced to the extent that arc-melted molybdenum would rupture intergranularly during hot forging. They also found that if the oxygen content was less than 0.003 pct, the cast molybdenum was hot forgeable. It is suspected, however, that forgeable molybdenum may contain a small amount of oxide that could reduce the ductility of the as-cast metal at room temperature. Also, there is the possibility of the unfavorable distribution of other impurities having a detrimental effect on the ductility of cast molybdenum. The results of a study of the influence of purity on the room-temperature ductility of cast molybdenum are presented here. Vacuum Arc-Melting to Produce High Purity Mo One way of determining the effect of impurities on the ductility of molybdenum is to prepare and test metal as free of all impurities as possible. Accordingly, the present investigation was undertaken with this in view. Arc melting in high vacuum (less than 0.1 micron of mercury) was chosen as the method for reducing the impurities below the concentrations occurring in commercial molybdenum. Commercial arc melting of molybdenum is carried out at about 50 microns pressure. During the arc melting, carbon and oxygen in the metal react to form carbon monoxide. By virtue of the vacuum process, the partial pressure of carbon monoxide is maintained at such a low value that the reaction greatly lowers oxygen and carbon contents. An excess of at least 0.03 pct C is used in commercial arc melting to insure that the oxygen content will be below 0.003 pct. The excess carbon remaining after the deoxidation step forms carbides on freezing. Some of the carbides precipitate at the grain boundaries and, as will be shown, have an unfavorable effect on the room-temperature ductility. In the present work, only the small amount of carbon (0.003 pct) contained in the commercial powder-metallurgy molybdenum used for melting stock was present. Partial removal of oxygen from the melt probably occurred as the result of the volatilization of molybdenum oxides, or by distillation of oxygen at the high melting tem-

Jan 1, 1953

By T. L. MacKay

Oxidation rates of single-crystal and poly crystalline zirconium in oxygen at temperatures from 307° to 815°C obey the parabolic rate law for short ex-posure time, 4 to 6 hr. The activation energy for the oxidation of single-crystal zirconium between 420° and 790°C is 42.6 ± 0.7 kcal per mole, and in the temperature range 307" to 600°C the activation energy for oxidation of poly crystalline zirconium is approximately the same. The high-activation energy is indicative that diffusion through the bulk oxide film is the primary mode of mass transport for both types of metal. The higher oxidation rates for poly -crystalline zirconium in this temperature range were attributed to differences in the orientation of the grains in the metal with respect to the oxidizing surfaces. Above 600°C, vain growth was observed in polycrystalline zirconium, and the oxidation rates approached those of single-crystal zirconium. ThE kinetic data of previous oxidation studies1-&apos; of zirconium in oxygen have been interpreted by both parabolic and cubic rate laws. There is some evidence that there is a transition from the parabolic to the cubic rate law at prolonged exposures, but the question is still controversial. For the parabolic rate law activation energies are reported in the range 18.6 to 35 kcal per mole, and for the cubic rate law in the range 38 to 47 kcal per mole. So far as the mechanism of zirconium oxidation is concerned, inert marker studies10,11 have indicated that the oxidation proceeds by oxygen (anion) diffusion through the oxide film toward the metal-metal oxide interface. Pemslerl2 observed that the orientation of the grains in the zirconium metal substrate affected the rate of formation of the oxide film on the surfaces of the grains and that the orientation dependence of the corrosion rate persisted beyond the initial stages of reaction. The rate of oxidation was a minimum when the c axis of the grain was parallel to the surface of the sample, and rose to a maximum when the c axis was inclined at about 20 deg to the plane of sample surface, and decreased again at higher inclinations. cox13 observed that in 300°C steam a thin oxide film was formed initially on zirconium and that this oxide film, which exhibited interference colors, became dark first along the grain boundaries and then over the whole surface in an inhomogeneous manner as the film thickened. Cox proposed a mechanism in which oxygen diffused along preferred paths created by grain boundaries in the metal and formed a much thicker film at or near the grain boundary than on the central zone of the grain. In the present study, the oxidation rates of single crystals of zirconium were measured in oxygen and compared with the oxidation rates of polycrystalline zirconium of the same bar stock. It was felt that such a comparison would elucidate the role of grain boundaries in the metal substrate. SAMPLE PREPARATION Single crystals of zirconium were prepared by following the procedure of I3apperport,14 starting with 1/4-in. rod purchased as crystal-bar zirconium. Zirconium rods 2 in. long were wrapped in tungsten foil and sealed in quartz tubes at pressures of less than 10-6 mm of mercury. Large single crystals were grown by thermal cycling above and below the a-/3 transformation temperature, 862°C. Several specimens were simultaneously subjected to the same cycling procedure, heating to 1200°C, holding for 4 hr, then cooling in the furnace and holding at a temperature of 840°C for 5 to 10 days. This cycle was repeated five or six times for each set of specimens. The grain size of the crystal-bar zirconium before thermal cycling was between 10 and 30 p. Fig. 1 shows the microstructure of an end section of as-received crystal-bar zirconium. A longitudinal section of each zirconium rod after thermal cycling was polished and examined under polarized light, see Fig. 2, and the largest single crystals were selected for this study. Zirconium rods 1/8 in. in diameter and 1/2 in. long with spherical ends were machined from the single crystals and from the as-received bar stock. An X-ray examination showed that the c axis of the single crystals made either a 34-deg or an 89-deg angle with the rod axis. The specimens were chemically etched for 2 min in solution consisting of 15 parts hydrofluoric acid (48 pct), 80 parts nitric acid, and 80 parts water. The chemical polish removed 1 to 2 mils from the surface. EXPERIMENTAL The Sartorius vacuum microbalance used in this study has a sensitivity of 0.5 pg and a capacity of

Jan 1, 1963

By C. R. Keyes

Discussion of the paper of C. R. Keyes, presented at the Chattanooga meeting, October, 190S, Bulletin No. 26, February, 1909, pp. 119 to 166. E. R. BUCKLEY, Flat River, Mo. (communication to the Secretary*) :-Some statements in the paper of Mr. Keyes relative to the nature and formation of the Ozark lead- and zinc-deposits seem to me erroneous and misleading, and I respectfully present the following criticisms, placing Mr. Keyes&apos;s original statements in quotations. Referring to the Ozark dome: (P. 127.) "It is a region that has been repeatedly upraised and planed off, until in the middle portion the oldest known&apos; rocks only are exposed." Does he mean that the St. Francois mountains, which have always been considered as lying on the eastern flank of the Ozark dome, are the middle of the dome? Or does he mean that the Cambrian rocks of the generally-accepted middle are the oldest known rocks ? Certainly not the latter, and if the former, his idea of the middle of the dome is not in accord with that of others who are familiar with the region. (P. 138.) " . . . the ore-deposits are definitely associated with, or localized by, geologic structures of some kind that .produce in effect basins in which&apos; the underground waters are impounded, or their flow retarded." This statement does not appear to be altogether consistent with the facts, since the ore- bodies of the Joplin district, as the rule, occur in those parts of the Mississippian formation which have a tendency to accel¬erate the flow of ground-water rather than retard it. I might name the open, breeciated ground near Joplin, Webb City, and Oronogo as especially noteworthy illustrations. The ore-bodies, everywhere, occur in positions where there must have been a free and copious circulation of dilute lead- and zinc-solutions in the presence of reducing constituents. The inequalities in the distribution of the ore-deposits are

Oct 1, 1909