Search Documents

By Leo F. Reinartz

Part II of a four-part series on the history of steelmaking in the US, points out the inadequate safety and living conditions that existed in steel mills at the turn of the Century. Also defined are furnace and process developments. OPERATIONS in steel plants today are highly mechanized. Men work in light, clean, orderly melting shops, making it difficult for old timers to convince young men that primitive, hazardous conditions existed in steel plants at the turn of the century. Working conditions then were very poor as compared to present day standards. In small plants especially, sanitary, locker, and washroom facilities, first-aid practices and stations were un- known Accidents were frequent and severe. Workers had a fatalistic attitude toward getting hurt. He who had an accident was looked upon as a hero. A dirty bandanna often served as a bandage. Infections were frequent. Electric cranes were in their infancy and broke down often Cables had not as yet replaced chains. Pig iron and scrap iron were loaded by hand in the stockyard, and stockyard locomotives were un- known; mules served as the usual motive power. It was not unusual to see recorded a delay of ½ hr in charging a furnace because of a balky mule. Furnace operations A few plants had primitive charging machines, but most furnaces were charged by placing scrap or pig iron on the paddle of a long peel, which rested on a bar across the furnace door opening. Laborers at the handle end of the peel, using the bar as a fulcrum, would heave the material into the furnace by a down and sideward motion of the peel handle. In time they became expert in placing these materials in the furnace, but it was hard, hot work, and a long time was required for charging. Cold charges of 25 tons required more than 12 hr for melting and re- fining the steel. Ports, doors, and frames were not water cooled. The charging and working area in front of the furnace was covered with steel plates. They were hot and often warped by the intense heat of the un- insulated checker chambers directly below. In the summer, working conditions on the charging floor were almost unbearable. Silica refractories were of poor quality. Because of this, and the inadequate training of furnace men in fuel control and furnace operations, roofs, front and back walls, and ends burned out rapidly. Dolomite machines were unknown; consequently, furnace banks and hearths were fettled with dolomite by the use of hand shovels. The round system required six or more men. Each man took a shovelful of dolomite and, in his turn, deposited it on the back wall and bank by a dexterous forward swing and twist of the shovel. The upward swing of the shovel partially protected his face from the searing heat of the furnace coming out through the wide-open door. Considerable skill and stamina were required to do this job properly. Reverse valves, usually of the cast-iron butterfly type, were located below the charging floor. They were operated by long levers on the charging floor level men they became warped, because of heat and abuse, great strength and skill were required to reverse them. Furnace operations were difficult. The quality and quantity of producer gas coming from irregularly stoked, hand-operated gas producers was uncertain and unreliable. Furnace Linings and ports were quickly burned out. Poor bottom and side-wall refractories, indifferent and inexperienced crews, as well as irregular re-

Jan 1, 1961

By E. S. Davenport

IT is indeed an honor and a responsibility to have been selected to present the thirty-fourth in this series of Henry Marion Howe lectures, established to perpetuate the memory of a great teacher and one of America's outstanding scientists. Previous Howe lecturers have established high standards for this annual AIME event. It has been my good fortune to have enjoyed close association with five of these former lecturers; namely, Bain, Grossmann, Johnston, Sosman, and Vilella, all of whom have been prominently identified with the research activities of the organization with which I am connected. Some years ago I had an opportunity to examine a letter written by Professor Howe in 1904. This document was particularly interesting to me since I never had the privilege of personal acquaintance with Professor Howe and do not recall even having seen him during his long and active career. In view of the fact that the letter dealt, to some extent, with matters related to the subject of today's lecture, I would like to quote briefly from it. The letter is datelined, "Bad Kissingen, June 11, 1904." The salutation reads, "Dear Bradley," which suggests that it was probably addressed to Bradley Stoughton, who, I believe, was working with Howe at Columbia University at that time. The letter reads, in part, as follows: "Austenite and Martensite. I have not examined what Osmond says in his new book. His former remarks about austenite I found very confusing, indeed unintelligible. I think we can reconcile matters well enough for the present by assuming that martensite is a transition step between austenite at one end and ferrite and cementite at the other. Above critical range for steel of 0 to 1.80 carbon, austenite is normal state; below Ar1, ferrite and cementite are normal." The letter then continues with a discussion of Osmond's ideas on metallographic nomenclature, particularly his use of the terms martensite, troostite, and sorbite, including the following pointed comment: "For common purposes it seems to me unwise to drag them in, and much simpler to confine ourselves to the end stages Austenite Ferrite plus Cementite Osmond does not really know his own mind— or does not clarify his ideas to others—as to nomenclature." Thus we see that, as far back as 1904, the transformation of austenite, and the products of that

Jan 1, 1958

By H. Reiss

The zone-melting process in which redistribution of solute in a solid bar is effected by the passage of a molten zone is considered mathematically. Simple approximate techniques are developed for computing the manner in which redistribution occurs as molten zones continue to pass. The introduction of the "zone-melting flux" provides valuable insight into the nature of the phenomenon, as well as a central mathematical theme in terms of which the process can be discussed. Curves are presented for typical and general cases. AN extremely efficient purification technique was described recently by Pfann.1 Known as zone refining, it consisted of the slow passage of a series of molten zones, produced by external heaters, through a long solid ingot of the substance to be purified. Equations were given for the maximum separation attainable, and a numerical computation method was described for obtaining the concentration in the ingot after a given number of zone passes. The present paper offers an interpretation of the physical nature of zone melting in terms of a transport process in which formal diffusive and convec-tive flows occur. This interpretation, in addition to providing insight into the physical nature of the process, also provides a basis for its mathematical treatment. From this basis, useful equations are developed for the solute concentration in the ingot as a function of the number of zone passes. These are applicable particularly where large numbers of passes are necessary and where numerical computational methods might be laborious. All considerations will deal with the limiting form of the process, described by Pfann,' in which: 1—Diffusion in the solid is considered negligible. 2—Mixing in the liquid is supposed, complete. 3—The distribution coefficient, k, measuring the ratio (at equilibrium) of solute concentration in the solid to that in the liquid is supposed, independent of composition. In general, this paper will be concerned with a bar of uniform (actually unit) cross section, ex- tending in the x-direction from x = 0 to x = L, where L may be infinite. Zone melting is a transport process, and as such must admit of interpretation in terms of a flux of transported quantity. However, the progress of operation is not measured in units of time but in terms of the number of completed zone passes. Consequently, the zone-melting flux will be a rate, per unit pass, rather than per unit time. The description of this flux and the examination of its properties is given below. Zone-Melting Flux Fig. 1 represents an intermediate stage of the nth pass. Concentration C is plotted against distance, x. The molten zone with its back at the point x and front at x + I moves in the direction indicated by the arrow. As it moves, it leaves behind the nth

Jan 1, 1955

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now been changed. to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which have equal and undivided interests in the property. The land and building cost two million dollars. During the gear 1934, the constitution and By-laws of The United Engineering Trustees, Inc., were thoroughly revised and a better organization of its functions was affected: The Engineering Foundation and the Engineering Societies Library were made "departments? of the United

Jan 1, 1936

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

A. Bement, Chicago,Ill. (communication to the Secretary*):— Formerly it was the general practice of engineers to designate coal that is free from moisture and ash as " combustible," notwithstandirig that it contains oxygen and nitrogen. The origin of this practice was more particularly due to the requirements in connection with boiler-testing, which demanded a consideration of that portion of the fuel which took part in the combuition-process because results based on a unit of either moist or dry coal were not comparable, since both moisture and ash were recognized as variable quantities. Thus, a pound of " combustible " became a standard of value, and was treated as a constant before employing measurements of heating-power and calculating therefrom the percentage of efficiency. The recognition of this term " combustible " was an advance to be credited to the engineer rather than to the chemist, because the latter, not having to do with the interpretation of analyses in practice outside the laboratory, usually saw no reason for reporting results in terms other than those of the moist-coal composition. Some years ago I needed a table of fuel-composition in terms of moist, dry, moisture-free and ash-free coal, and of the combustible components. This table required the use of the word combustible in its proper sense, for the purpose of designating carbon, hydrogen, and sulphur, instead of including these three elements with oxygen and nitrogen, to which aggregate the term combustible was formerly applied. To make such a tabulation involved either the use of the inconvenient and cumbersome term, "ash- and moisture-free coal," or of some other representative term, and for this purpose I adopted the expression pure coal, which is short, simple, convenient, and technically correct. It is also harmonious, because it agrees

Jan 1, 1909

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby

By N. J. Grant, E. Gregory

The creep rupture properties of wrought aluminum powder products made from five grades of sintered aluminum powder were investigated at temperatures from 400° to 900°F for rupture times up to 1000 hr. The effect of stress concentrations on materials of this type was investigated by means of notched creep rupture tests. A tentative correlation was obtained between the creep rupture properties and the structure as revealed by electron micrographs. SEVERAL papers have been published recently concerning the production and properties of wrought aluminum powder products and their possible high temperature applications. Most of the published work in this field has come from abroad, notably Switzerland, and articles by Irmann and his colleagues were summarized in English recently.'.' Most of the papers published by Dr. Irmann are principally concerned with the retention of properties (by a product which is produced from extremely fine flake powder and is subsequently hot extruded) after heating to high temperature for prolonged times. The powder may be in atomized or flake form, and during hot working the applied pressure is reported to plastically deform the aluminum powder, thus breaking the oxide skin and welding the particles together. Irmann attributes the remarkable properties to the dispersion of oxide inclusions. Specifically, the product described by Irmann is one labeled SAP (Sintered Aluminum Powder) in which the initial flake powder is so fine that at least 50 pct of the flakes have one dimension of 2 microns or less. The composition of the starting aluminum shows in percent, Fe, 0.18; Si, 0.19; Zn, 0.06; Ti, 0.03; Cu, Mn, Mg, all nil; balance Al, approximately 99.5 pct. Aluminum is not the only material that has been found to have increased resistance to deformation at elevated temperatures when produced by powder metallurgy. It has been reported by Middleton, Pf eil, and Rhodes- hat platinum has a higher recrys-tallization temperature when produced by powder metallurgy and exhibits peculiar properties, many of which are similar to those of the aluminum powder products. Difficulties were encountered in explaining the reason for the strengthening in the case of platinum since the existence of the oxide is doubtful. The authors attributed the special properties to "a small amount of suitably dispersed porosity." This theory was supported by von -~eer-leder4 in the discussion to the paper, and the similarity between this method of hardening and that suggested by Rohner in his theory of age hardening was pointed out. R. de Fleury5 attempted to explain some of the properties in terms of the modulus of elasticity and elastic limit of alumina and aluminum while von Zeerleder examined the relationship between the yield strength and the reciprocal of the powder particle size. Boenisch and WiderholtQ dealt mainly with the corrosion resistance of the powder aluminum material and compared it with other aluminum alloys. The diffusion rates of other metals in SAP and pure aluminum have been compared by Seith and Lop-mann.' They showed that the alloying metals diffuse particularly quickly in SAP possibly due to the very fine grain size. The properties of the Alcoa products were given by Lyle.' The creep rupture properties of SAP and two of the Alcoa experimental powder products were compared by Gregory and Grant hnd it was shown that these products are vastly stronger at 900°F than are the best cast and wrought alloys at 600°F. Since the publication of these data, the authors have investigated two further aluminum powder products and it is the object of this paper to show how the high temperature creep rupture properties of the five materials vary with oxide content and with the structure as revealed by electron microscopy. Materials One of the five products, SAP, a sintered aluminum product, was supplied by the Societe Anonyme pourl Industrie de l,Aluminium, Neuhausen a/RHF, Switzerland, through Dr. R. Irmann, while the others, M276, M257, M293, and M255 were supplied by the Aluminum Company of America as experimental powder metallurgical products. M255- and M293 were made from coarse and fine atomized powders, respectively. The other materials were made from flake powders with significant differences in oxide content, the details of the type of powders used in the manufacture of these materials

Jan 1, 1955

By Joseph C. McCaskill

The writer assumes that this volume is not intended to serve as a source of statistics on international trade and that the reader is not interested in wading through a lot of statistical tables copied from the various reporting agencies. Generalizations therefore are made whenever possible and not always is the source of the information meticulously cited. The United Nations regularly publishes trade data on mineral commodities. E. J. Gealy, and C. L Kimbell, of the U S Bureau of Mines (USBM), work with these data and estimate that they cover approximately 78% of total mineral commodities traded. In addition the General Agreement on Tariffs and Trade (GATT) publishes analyses of certain trade data The most complete report of production and trade in minerals 1s probably the international volume of the U.S. Bureau of Mines Yearbook The latest available edition is for 1968, and some of the data in this edition cover only as late as 1967. Unless otherwise stated, the source of data used in the chapter is this Yearbook Other staff members of the Bureau were most helpful and cooperative They are not to be held responsible for conclusions or points of view to be found in the chapter. THE NATURE AND SCOPE OF INTERNATIONAL TRADE The two and a half decades since World War II have witnessed an unprecedented growth international commerce The end of the war found the world economy seriously crippled. Many countries had suffered severe war damage; international trade was disrupted and nations had to resort to exchange controls and bilateral trading arrangements. The postwar recovery, however, was remarkably rapid Within two decades, world Income more than doubled, and world trade which was less than $60 billion in 1948 exceeded $200 billion in 1968, 8 and reached $278 billion in 1970.18 The growing world trade contributed to world prosperity which in turn fostered growth of trade. This dramatic growth of international commerce was made possible by the progressive liberalization of trade and capital movements by the major trading nations of the world which began immediately after the War and has not yet completely lost its steam. The modern-day stimulus of the expanded trade movement was the enactment by the Congress of the United States in 1934, of the

Jan 1, 1976

By J. D. Hanawalt

Significant strides were made in the year 1948 leading to further recognition of the place of magnesium as a common commercial metal, rather than as just a premium aircraft material. One of the factors contributing to this recognition was the price stability and, in many cases, price reduction of magnesium products in 1948. In contrast to most other metals, manufacturing advances in magnesium outweighed the effects of increased labor and other costs. At the present time, many magnesium extrusions, die castings, and permanent mold castings can be purchased as cheaply as their aluminum counterparts in these forums, though competitive prices for sheet still await the inauguration of a modern tandem rolling mill for magnesium, such as has already been demonstrated.

Jan 1, 1949

By J. H. Yang, K. E. Gray

Results of single-blow bit-tooth impact tests on saturated rocks under elevated confining pressures and zero pore pressure were reported in a previous publication.1 This paper presents an extension of the earlier work to include a study of crater formation during tooth impact on both gas- and liquid-saturated Berea and Bandera sandstones at elevated confining and pore pressures. The basic data obtained were force-time, displacement-time, velocity-time and force-displacement curves during crater formation. Crater volume was also measured and the mode of crater formation determined. Bit tooth geometry, depth of penetration and velocity of impact were held constant. Results indicate that, with pore fluid present in the rock, failure trends from brittle to ductile as pore pressure is increased at constant confining pressure (pore pressure and borehole pressure were equal) For a given rock type, the mode of crater formation was dependent not only upon the nominal effective stress, but also upon the fluid which saturated the rock pore space. When confining pressure and pore pressure were equal (zero nominal effective stress), bit-tooth impact resulted in brittle failure for nitrogen-saturated Berea, and brittle to transitional failure for nitrogen-saturated Bandera; when saturated with liquid both rocks failed in a ductile manner at zero nominal effective stress. INTRODUCTION Dynamic wedge penetration tests have been conducted by investigators in several fields, but the failure mechanism of rock under dynamic stresses is not understood completely. The complex action of drilling bits, even considering the action of a single tooth, may be considered as a combination of drag bit and rolling cutter action. Thus, as a first step in understanding rock breakage in oil well drilling, single chisel impact and rock planing are of fundamental importance. For example, Gray 2 and Crisp3 studied drag bit cutting action at brittle stress states. Simon4 and Hartman5 studied the reaction of rocks to vertical impact by means of drop tests. The depth of penetration, crater volume and force-vs-time curves during crater formation were observed. The significance of indexing single-bit impacts has been noted.4,6-8 Gamer et al,9 reported impact tests on impermeable Leuders limestone at atmospheric and elevated confining pressures. In all cases the tests were accomplished on dry rock and pore pressure was considered to be zero. The importance of both confining pressure and pore pressure on the failure characteristics of rock was described. 10-12 It was found that the yield strength and ductility of porous rock depend on the state of stress under which the sample is tested. The importance of pore pressure on drilling rate in microbit experiments was noted by Cumingham and Eenink. l3 Robinson 12 also pointed out that in drilling the most important parameter in rock failure is the effective stress, where effective suess is defined as confining pressure pc minus pore pressure pp. The effect of pore pressure and confining pressure on rock strength was also noted by Serdengecti and Boozer 14 in strain rate tests, and by Gardner, Wyllie and Droschackl5 in elastic wave studies. Until recently all reported wedge impact studies under simulated wellbore stress states have been conducted on dry rock. Maurer 16 reported impact tests on samples saturated with deaerated water. Borehole and formation fluid pressures were equal in these tests except when mud was used in the borehole. With mud in the borehole and a high borehole-to-formation fluid pressure differential. Maurer observed "pseudoplastic" crater formation. Podio and Grayl reported impact tests on Berea and Bandera sandstone saturated with pore fluids having wide ranges in viscosities. In Podio and Gray's tests, confining pressure was elevated, but pore pressure and borehole pressure were held fixed at atmospheric pressure. The presence of

By Robert Adams

Secondary or scrap materials appear at all stages in the industrial process and in a bewildering variety of forms, grades, and values. It is useful to begin analyzing them by dividing the broad concept of "Secondary Supply" into three parts First, the concept must encompass the stock, or pool, of secondary materials. In the process of satisfying his wants, man produces desired products from the materials and natural resources found around him. As long as the rate of production is greater than the rate of obsolescence of a given product, the total stock or pool of materials embodied in that product will increase in size This stock concept relating to secondary materials is directly analogous to the "resource" concept used for primary raw materials in the preceding chapter, and includes all materials embodied in existing products (Obviously, this excludes those materials which are destroyed in the consumption process, viz , fuel oil burned to provide heat.) Consumption of a primary material in a productive process tends to reduce the resource base of that primary material In direct contrast, however, the production or use of products increases the resource base of the secondary material. Thus, we find that a country which has no resource of a primary material can, by importing products that contain the material, build up a large enough stock to provide a basis for secondary recovery. The estimated growth of the pool of copper in use in the United States through 1967 is shown in Table 5.B.1.a The estimate of 39 3 million tons at the end of 1967 includes only technologically recoverable copper and is, therefore, somewhat less than the stock concept described previously, which does not distinguish between recoverable and unrecoverable material. Nevertheless, Table 5 B.1 does give an idea of how a nation's secondary resource of a material can grow over the years. A second aspect of the concept of secondary supply is the generation of secondary materials. This includes materials generated as scrap in production as well as the movement of a material out of the stock of existing products via wear, damage, or obsolescence The quantity of materials generated is usually either nearly or completely independent of the technologic capabilities and economic forces which prevail in the secondary recovery market.b The justifications for and the qualifications to this statement are considered later. The final aspect of the concept of secondary supply consists in the secondary recovery process It is at this point that the technologic and economic forces of the secondary recovery market become the controlling fac-

Jan 1, 1976

By Howard V. Sears

ArcHodrilling (Arcuate Hole Drilling) of short radius overhead curved holes from within the working level with a new, small-diameter in-the-hole drill produces tangible, assayable chip samples from the entire height of the projected mine level where the hole arcs down immediately in front of the working face. Drilling through the projected level with diamond coring tools produces samples showing the competence of roof and floor strata as well as the geological and economic characteristics of the ore. Hand-portable solid state electronic surveying instrument has been developed to survey the ArcHole and a convenient nomograph plotting record sheet converts survey digital readouts to hole inclination in degrees, to radius of curvature in feet, and to attitude of the plane of curvature from vertical in degrees, all without calculation. The ArcHodrilling system offers a tool with which the exploration geologist can more nearly assess the true potential of old mining properties being reexamined and to reduce the number of surface diamond drill holes needed to secure development data about new ore bodies. It gives the mine geologist an opportunity to secure those data at a fraction of the cost of drilling from the surface. The mining supervisor has a convenient, cheap tool to look ahead to know what he will be mining tomorrow. The mill supervisor has an opportunity to reduce his mineral loss in tailings by being able to anticipate the grade of his mill feed.

Jan 1, 1973

By J. W. Hickman, E. A. Gulbransen

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By W. H. Herrnstein, J. B. Clark, E. C. Utley, A. J. McEvily

The ratio of the endurance limit (10' cycles) to tensile strength of age-hardened aluminum alloys is approximately 0.3, whereas the ratio for annealed alloys is about 0.5. The lower value for the age-hardened alloys has been associated with the instability of coherent precipitate during cyclic loading, but it has not been definitely established whether this instability is due to overaging or reversion during cyclic loading. The results of the present investigatzon support the reversion viewpoint. In this work specimem of 2024-T4 aluminum alloy were aged for 16 hr at 150°C after cycling for 10 pct of the life at 25.000 psi. These specimens were then tested to failure and exhibzted a marked increase in fatigue life. It is proposed that during the early stages of fatigue in this alloy dislocations cut through the coherent precipitate and bring about the reversion of the precipitate. Subsequent aging at 150ºC induces reprecipitation in the precipitate-free zones so that the weakened regions are strengthened and the fatigue life is extended. It Is recognized that the fatigue strengths of precipitation hardened aluminum alloys are unusually low relative to their tensile strength.'-= This feature is illustrated in Fig. 1 where it can be seen that age-hardened alloys have lower fatigue ratios (the ratio of the fatigue strength to the tensile strength) than those in the annealed or cold worked state. Further, as shown in Fig. 2, the more an alloy is dependent upon precipitation hardening for its total strength, the lower is the ratio of the fatigue strength to the tensile strength. This state of affairs has been associated with an instability of the metastable metallurgical structure of precipitation hardened aluminum alloys during cyclic loading. Evidence2 in support of this view is that the fatigue ratio increases in these alloys as the test temperature is lowered, thereby indicating that thermo-mechanical instability, rather than some other factor such as a non-uniform distribution of precipitate, is the factor responsible for the low fatigue ratio at room temperature. Two mutually exclusive proposals have been ad- vanced to account for this instability. Hanstock has proposed that overaging takes place during cyclic loading, and in support of this view, Broom et a1.2 have indicated that an overaging process might be promoted by the large numbers of vacancies which are created during cyclic loading. The creation of vacancies by radiation4 has been shown to lead to rapid overaging. Hanstockl obtained visual evidence of overaging in an aluminum alloy after cyclic loading, but in this instance it has been pointed ou? that because of the high frequency used (60,000 cpm) the observed effect may have been due to normal high temperature precipitation around energy dissipating cracks. Efforts to discern visual evidence of overaging in this alloy at lower test frequencies were not successful.3 The alternative postulate3 is that reversion takes place during cyclic loading and leads to localized soft spots at which fatigue cracks are readily initiated. Evidence for this process has recently been provided by Polmear and Bainbridge5 who demonstrated metallographically that regions depleted of precipitate were created during cyclic loading of an aluminum alloy. Inasmuch as precipitate particles bordering the depleted region had not grown in size, it was concluded that the solute atoms which had constituted the missing particles had gone back into solution. No mechanism for the reversion process was presented. The present study was undertaken to investigate further the conditions leading to instability during cyclic loading, and to determine whether reversion or overaging had taken place as a result of cyclic loading. BACKGROUND AND TEST PROCEDURE In order to differentiate between the processes of reversion and overaging, rest periods at an elevated temperature, which ordinarily would insure additional precipitation, were used in this investigation. It was expected that after a period of cyclic loading an elevated temperature rest period would result in a decrease in the remaining life of the specimen if overaging were occurring during cyclic loading, whereas in the case of reversion, reprecipitation would occur and the fatigue life would be extended. Such an expectation is based on the assumption that the crack-nucleation phase is a significant portion of the total fatigue life, and that such a treatment is of influence in the crack-nucleation stage and is relatively unimportant thereafter.

Jan 1, 1963

By D. Kramer

HASEN1 has published a phase diagram for the zirconium-nickel system. This phase diagram has been redetermined by Hayes, Roberson, and paasche2 in the range 0 to 50 at. pct Ni. Recently, Smith and Guard3 have published a tentative diagram for the

Jan 1, 1960

By J. H. Wiggins

Granting that about 600,000,000 bbl. of light oil will be produced in the United States this year and taking the Bureau of Mines' statement that 71/2 per cent. of the total crude production will be lost before the finished gasoline is shipped from the refinery, the volumetric evaporation will be 45,000,000 bbl. of the cream of the gasoline. This is a ConseNative figure and is equivalent to 1,890,000,000 gal. The real value of this liquid is at least 150 per cent. of the value of an equal volume of motor fuel. At only 10 c. per gal., the value lost is $189,000,000; at 15 e. per gal. the loss is $283,000,000. If 750,000,000 bbl. of light and heavy oil are produced here this year and the average price per barrel is $1.333, the gross return to producers will be $1,000,000,000 and the net returns about $200,000,000, if the cost of production is only $1 per barrel. Thus, the evaporation bill is about 20 per cent. of the gross income and is equal to the net income of the crude-oil producers. Two other comparisons with popular phases of the petroleum industry will help give an adequate conception of the evaporation problem. These are: cost of preventing evaporation compared to cost of cracked gasoline and volume of gasoline evaporated compared to volume of gasoline manufactured from natural gas. When gasoline is manufactured from heavy oils by the cracking process, there are two important divisions of the total cost of the product: the manufacturing cost, such as plant cost, operation, maintenance, etc., and the cost of the barrel of heavy oil, from which the cracked gasoline is made. In preventing evaporation loss the cost first mentioned enters into the total cost, but the second cost is eliminated; that is, no charge is necessary for stock from which to manufacture the saving. A detailed analysis of these two costs on a large scale shows that the net income from a dollar spent in preventing evaporation loss from the lease through the refinery is twice the net income from a dollar spent in cracking. Of

Jan 1, 1924

By N. K. Chen, R. Maddin

In the extension of molybdenum single crystals at room temperature, the slip planes were found to be of the type (1101; the slip direction <111>. Theories of plasticity of body-centered cubic metals have been examined, and an explanation based upon planes of highest atomic density seems plausible to explain the plastic behavior of molybdenum single crystals. IN body-centered cubic metals, slip has been reported to occur on several planes; these are of the type {110), {112), and (123). Andrade has correlated&apos; the operative slip planes in body-centered cubic metals with the testing temperature relative to the melting point. In this correlation, if T is the absolute temperature at which slip takes place and Tm the absolute melting point, then the acting slip planes in body-centered cubic metals may be arranged as shown in Table I. However, deviations from this correlation have been reported in iron and iron-silicon alloys2 and also in molybdenum deformed at a temperature around 2400°C." In the case of iron and other body-centered cubic metals or alloys in which all three slip planes have been reported to be active at any one temperature, the crystallographic mechanism of slip is not well understood. Numerous investigators in this field have assumed that the resolved shear stress is a deciding factor. Such considerations were given by Gough in his experiments with repeated torsion of iron single crystals4 and recently by Opinsky and Smoluchowski in their study of iron-silicon alloys," and will be dealt with later in this report. A third possibility is that slip lines in body-centered cubic metals may be formed by alternate slip on nonparallel (110) planes and not by slip on any plane of higher indices. This was advanced by Elam in the case of ß brass." Since (1101 planes are planes of highest atomic density in the body-centered cubic structure, this hypothesis would be in accordance with the plastic behavior of metals in other systems, namely, face-centered cubic and hexagonal close-packed. Experimental evidence in support of this hypothesis is lacking. Nevertheless the work of Barrett, Ansel, and Meh12 has definitely demonstrated that the slip resistance on {110} planes in iron is very much smaller compared with that on (112) and (123) planes. In the present investigation, molybdenum single crystals were carefully documented as to the operative slip planes and lattice reorientations after plastic extension at room temperature. In three crystals studied, (110) planes were found to be active invariably rather than the (112) planes, which were previously reported for molybdenum at this temperature&apos; and predicted by Andrade&apos;s theory.&apos; In two other cases (112) and (123) planes seemed to operate together with (110) planes as active slip planes. However, it is believed, after careful analysis of crystallite and lattice rotations, that slip on (112) and (123) planes may be spurious. Particular reference will be made to the formation of asterism, lattice rotation, and crystallite rotation in an attempt to show that slip apparently observed on {1121} and (123) planes is actually slip on nonparallel {110} planes. Materials and Treatment Sintered molybdenum rods ? in. in diam, obtained from the Fansteel Metallurgical Co., were reported to have a purity of 99.9 pct.* One specimen, Mo-13, ¼ in. in diam, was supplied by Westinghouse Electric Corp. Single crystals were prepared, using the technique devised by Chen, Maddin, and Pond." Mo-13 was ¼ in. in diam x 7 in. long with a reduced gage section of 0.200 in. in diam x 3 in. long. The center of

Jan 1, 1952