Search Documents

By C. S. Smith, Chih-Chung Wang

TURNBULL and his collaborators1,2 have developed the theory of homogeneous nucleation as applied, inter alia, to solidification of liquid metals. Vonnegut³ and Turnbull4 have shown that if a liquid metal is subdivided into small droplets a vast majority of them will undercool very considerably before solidification, generally to as low as about 0.8 of the freezing temperature on the absolute scale. The nuclei effective at small degrees of supercooling in bulk metal seem to be internal or surface heterogeneities, relatively small in number. If the metal is subdivided, those droplets that happen to contain such nuclei will solidify at a temperature not greatly below the true freezing point, but only a small part of the whole volume will be affected and the majority of the drops will under-cool to the much lower temperature at which homo- geneous nucleation occurs as a result of fluctuations. It occurred to one of the authors that an appropriate subdivision to give effective freedom from random nuclei is produced during the solidification of many alloys that contain a minor amount of a phase of low melting point, and that one might then expect marked undercooling of the distributed phase. Experimental: The alloys selected for initial study were copper with minor amounts of lead and bismuth, and aluminum with tin. In all these alloys, the major component freezes at a temperature not much below that of the pure metal, and there is little further change in constitution on cooling until the lower melting point constituent freezes in an almost pure state. Cooling curves were taken using the controlled heat flow method permitting approximate specific heats to be obtained. Chromel-alumel thermocouples were used, with the standard emf tables, since extreme precision was not needed. The crucible (3/4 in. id, 5/16 in. wall) was made of B & W K-20 insulating brick. It held about 10 cc of the alloy being investigated. The cooling rate was 2.5" to 2.9°C per min under a controlled temperature difference of 20°. Approximate specific heats were computed from the inverse rate curves together with data from a blank run and from a standard run with a copper cylinder of known heat capacity. The alloys for investigation were made from high-purity metals (99.99+pct) and cast into graphite molds. The castings were machined to fit the crucible and to provide a hole for the inner thermocouple. Cooling curves were taken after heating to a temperature about 50" above the melting point of the minor, lower melting-point, constituent. Results The lead phase in an alloy of copper with 5 pct lead did not undercool more than 3" below the melting point of lead (327°C) either as cast or after annealing to produce a new dispersion of the liquid phase. A copper-zinc-lead alloy with 23.75 pct zinc and 5 pct lead undercooled more but showed no thermal effect below 319°C. A cast alloy of copper with 5 pct bismuth undercooled to 249°C (M.P. bismuth 27l °C), but once solidification started it was completed at the same temperature. This was anticipated, since the bismuth forms a nearly continuous phase between the grains of copper, and a solid crystal nucleated anywhere would rapidly* con- sume the entire network of liquid, unless the physical continuity of the liquid were broken through volume changes, inadequate fluidity, or gas evolution. Similar arguments apply in the case of copper-lead alloys, where the lead-rich liquid forms a network along grain edges, though not grain faces. In both cases there would be a few isolated particles

Jan 1, 1951

By Herbert Clark Hoover, Lou Henry Hoover

DIFFERENT methods of parting gold from silver, and, on the other hand, silver from gold, were discussed in the last book; also the separation of copper from the latter and further, of lead from gold as well as from silver ; and, lastly, the methods for refining the two precious metals. Now I will speak of the methods by which silver must be separated from copper, and likewise from iron.1 The officina, or the building necessary for the purposes and use of those who separate silver from copper, is constructed in this manner. First, four long walls are built, of which the first, which is parallel with the bank of a stream, and the second, are both two hundred and sixty-four feet long. The second, however, stops at one hundred and fifty-one feet, and after, as it were, a break for a length of twenty-four feet, it continues again until it is of a length equal to the first wall. The third wall is one hundred and twenty feet long, starting at a point opposite the sixty-seventh foot of the other walls, and reaching to their one hundred and eighty-sixth foot.

Jan 1, 1950

By W. H. Bassett, J. C. Bradley

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. 11 is suggested that the materical is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the shad. Figures 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent. Structure of Protuberances The segregation of oxide between grains in the interior of the cast bar, not far from the "set," is shown in Figs. 5 and 6. In general, the amount of cuprous oxide begins to increase at a point about 0.01 in. below the normal surface of the casting, i. e., the base of the drop; but it does not attain maximum concentration in the main body of the metal. Vertical sections, Figs. 7 to 12, show that there is a definite line of large cuprous-oxide globules at the base of the drops. Horizontal sections at this place show that these large globules lie in a thin billowy

Jan 1, 1926

By C. H. Mathewson

THIS paper was prepared upon request as a contribution to a symposium covering the manufacture, properties, and uses of the important non-ferrous metals. In approaching a subject as broad as this, there is a natural desire to build up a comprehensive and finished production which shall constitute a dependable source of information on all questions properly belonging to this branch of metal technology. There are, however, a number of circumstances, apart from the mere routine of labor and thought involved, which operate rather effectively against the possibility of completing such an ambitious program at the present time. First of all, as far as any public record of results is concerned, the commercial rolling, drawing, and forming of zinc with relation to changes of structure and properties-and this we consider to constitute the elements of metal technology-might as well be an unpractised art. We have never seen a published photomicrograph showing the structural characteristics of either hard or soft sheet or strip, although the structure of castings has been frequently described, and other coarse-grained structures resulting from hard-hammering and annealing have been reproduced. Thus, an author in this field must proceed to his task without much assistance from the literature, and the outcome can represent only a personal estimate of principles, facts, or findings, and not a summary

Jan 9, 1919

By James J. Bean

HE task of measuring the specific gravity of the -*- operating medium in a heavy-media separation system has never presented a particularly difficult problem because the medium is fairly stable and the overflow of the separatory vessel, as well as its underflow, can be sampled easily and accurately and the specific gravity of the suspension determined easily by weighing a known volume. However, while this method is simple and accurate it does require the operator to take the sample by hand and to weigh it and there is considerable temptation to avoid the periodic sampling if everything seems to be going well, or if something is occupying the attention of the operator. Furthermore all operators do not sample in exactly the same manner and considerable practice is required for two operators to be able to "check" each other to the last few hundredths, particularly if the sample is cut underneath the drainage screen where location of the point of sampling and load on the screens tends to influence the determination. While none of the above presents much of a problem, we have all recognized that some mechanical method of continuous measurement and recording would be advantageous since the operator would merely have to glance at the meter to check the gravity and to have an indication of the trend of any changes. Also if the instrument were of the recording type, a permanent record would be available for the guidance of the superintendent. The Eagle-Picher Mining and Smelting Co. was the first heavy-media user to actually install such a recording meter. In 1946 they installed in their Central Mill at Cardin, Okla., a specific gravity recorder manufactured by the Bristol Co. of Water-bury, Conn. R. A. Barnes, of the Bristol Co., working with E. H. Crabtree, Jr. and Elmer Isern, of Eagle-Picher, made the application and worked out the problems of sampling and measuring. Their attempts to measure the specific gravity of the medium in the cone itself were not entirely successful and they resorted to an outside sample tube for actually making the determination. Because of the particular flowsheet used, it was possible to tap off from the medium return pipeline a stream of medium and divert it into the sampling tube, which was provided with a constant level overflow and a spigot underflow, and into which the bubbler tubes dipped. The Eagle-Picher installation was successful and its possibilities were recognized by the Mineral Dressing Laboratory of the American Cyanamid Co. It was decided to install a similar unit in the heavy-media pilot plant to investigate further its possibilities. Chief among these was the continuous record which it was felt would be proof of the steadiness of the gravity in a heavy-media cone, something which is not always appreciated by POtential users. Because the heavy-media pilot plant is required to operate at a wide range of specific gravities, it was realized that the unit would have to record all gravities from 1.25 to 3.50, and do it to the nearest 0.01. It would not be necessary to record all of this wide range on a single chart and the method selected was to have 4 bands, each band range overlapping the other a small amount and calibrated so that with standard charts one division would represent 0.01 sp gr. A shift from one band to another could be arranged without alteration of the instrument itself, being accomplished by a simple change in the bubble-tube lengths, as described later. Accordingly, a recording type instrument was purchased and installed. Because there were some advantages in doing so, the first installation attempted to measure the gravity of the cone proper by placing the bubble tubes in the cone. This was not at all satisfactory and the second scheme utilized a fixed vertical screen at the surface of the cone, and an external sample-tube arrangement. We were particularly anxious to make this work as we felt it would be advantageous to measure the top level of medium where the separation was actually being made, but we were doomed to disappointment because it was impossible to keep the screen clean of float. Since the top gravity of the cone is the most convenient place to sample for control, a launder about 2 in. wide was installed longitudinally beneath the

Jan 1, 1951

By James J. Bean

HE task of measuring the specific gravity of the -*- operating medium in a heavy-media separation system has never presented a particularly difficult problem because the medium is fairly stable and the overflow of the separatory vessel, as well as its underflow, can be sampled easily and accurately and the specific gravity of the suspension determined easily by weighing a known volume. However, while this method is simple and accurate it does require the operator to take the sample by hand and to weigh it and there is considerable temptation to avoid the periodic sampling if everything seems to be going well, or if something is occupying the attention of the operator. Furthermore all operators do not sample in exactly the same manner and considerable practice is required for two operators to be able to "check" each other to the last few hundredths, particularly if the sample is cut underneath the drainage screen where location of the point of sampling and load on the screens tends to influence the determination. While none of the above presents much of a problem, we have all recognized that some mechanical method of continuous measurement and recording would be advantageous since the operator would merely have to glance at the meter to check the gravity and to have an indication of the trend of any changes. Also if the instrument were of the recording type, a permanent record would be available for the guidance of the superintendent. The Eagle-Picher Mining and Smelting Co. was the first heavy-media user to actually install such a recording meter. In 1946 they installed in their Central Mill at Cardin, Okla., a specific gravity recorder manufactured by the Bristol Co. of Water-bury, Conn. R. A. Barnes, of the Bristol Co., working with E. H. Crabtree, Jr. and Elmer Isern, of Eagle-Picher, made the application and worked out the problems of sampling and measuring. Their attempts to measure the specific gravity of the medium in the cone itself were not entirely successful and they resorted to an outside sample tube for actually making the determination. Because of the particular flowsheet used, it was possible to tap off from the medium return pipeline a stream of medium and divert it into the sampling tube, which was provided with a constant level overflow and a spigot underflow, and into which the bubbler tubes dipped. The Eagle-Picher installation was successful and its possibilities were recognized by the Mineral Dressing Laboratory of the American Cyanamid Co. It was decided to install a similar unit in the heavy-media pilot plant to investigate further its possibilities. Chief among these was the continuous record which it was felt would be proof of the steadiness of the gravity in a heavy-media cone, something which is not always appreciated by POtential users. Because the heavy-media pilot plant is required to operate at a wide range of specific gravities, it was realized that the unit would have to record all gravities from 1.25 to 3.50, and do it to the nearest 0.01. It would not be necessary to record all of this wide range on a single chart and the method selected was to have 4 bands, each band range overlapping the other a small amount and calibrated so that with standard charts one division would represent 0.01 sp gr. A shift from one band to another could be arranged without alteration of the instrument itself, being accomplished by a simple change in the bubble-tube lengths, as described later. Accordingly, a recording type instrument was purchased and installed. Because there were some advantages in doing so, the first installation attempted to measure the gravity of the cone proper by placing the bubble tubes in the cone. This was not at all satisfactory and the second scheme utilized a fixed vertical screen at the surface of the cone, and an external sample-tube arrangement. We were particularly anxious to make this work as we felt it would be advantageous to measure the top level of medium where the separation was actually being made, but we were doomed to disappointment because it was impossible to keep the screen clean of float. Since the top gravity of the cone is the most convenient place to sample for control, a launder about 2 in. wide was installed longitudinally beneath the

Jan 1, 1951

By J. E. Hilliard

Various methods are given for estimating the number per unit volume and average size of convex particles from measurements on a projection through a slice of the structure. The determination of the size distribution is considered specifically for spherical particles. The results are applicable to any type of transmission microscopy and also to the correction of measurements made by reflected light on semitransparent materials. WITH the advent of electron transmission microscopy, the metallurgist is confronted with the problem of relating a projected image to the three-dimensional properties of the structure. This paper deals with the estimation of the number per unit volume and size of particles dispersed in a matrix. The case of convex particles will first be treated (the results will be applicable as approximations to particles of more general shape) and then spherical particles will be considered specifically. The latter represent a special case frequently encountered in practice and one which is also amenable to a calculation of the effect of overlap on the observed particle-size distribution. Although the present treatment was prompted by the needs of the electron microscopist, the results are applicable to transmission studies with any type of radiation. In addition, they can be used in the analysis of semitransparent materials by reflected light, the depth of light penetration corresponding to the thickness of the slice or section used in the transmission studies. 1) CONVEX PARTICLES 1.1) General Expression for N,. We will suppose that a "center" (such as the center of mass) is assigned to each particle. The convention used for defining the center is immaterial providing it does not depend on the orientation or location of the particle. Consider a slice through the structure having a pair of parallel faces a distance t apart. It will be assumed that the slice is randomly located with respect to its perpendicular distance from some fixed point, but it is not necessary to assume that its orientation is random. Our problem is to deduce the relationship between the number of par- ticle images seen on an orthogonal projection through the slice with the number, Nv, of particles per unit volume in the original structure.* *Symbols are listed in the Table. The expected number of particles with centers lying within the slice is Nvt per unit area. In addition, there will be elements in the slice contributed by particles whose centers lie without. The number of such elements will be the same as the number of intersections occurring on a two-dimensional plane through the structure; namely N~K, where K is the mean distance, Fig. 1, between tangent planes to a particle averaged over all particles, i.e., Where Ni is the number of particles of class i having the same shape and size, and pi (4, 8) is the probability that an i particle will have a given orientation with respect to the slice. If the particles are randomly oriented, then K is independent of the orientation of the slice and equal to the mean cali-per diameter. The total number of particle elements in the slice is therefore Nv(t + K) per unit area, but fewer will be seen as separate images on the projection plane because of overlap. If MA is the number of elements "lost" by overlap, the number of images per unit area will be NA = Nv(t + K) -MA 121 MA is a function of the slice thickness and must vanish at t = 0. As t increases, NA at first increases, reaches a maximum, and thereafter decreases as the overlap term MA becomes predomi-

Jan 1, 1962

By Eugene A. Mizikar

A mathetnatical model of heal transfer in continuously cast steel slabs is described. The model, consisting of a unidimensional transient conduction equation and boundary condition equations, has been pvogrammed for computer solution. Temperatuve and solidification profiles calculated for a 6-in. slab, being cast under several conditions of secondary cooling, are presented and compared. Calculated solidification profiles are in agreement with reported expevinle~ztal values. For the mold zone, the predicted slab shell thickness can be described by: Resuilts of the study indicate that multibank spray cooling followed by radiant cooling should be employed when solidifying thick slabs with minimum surface temperature of 1600°F. Under these conditions, a 6-in. slab can be expected to solidify in about 8.3 min. Computer results also indicate that radiant cooling can replace spray cooling during solidification of the final 30 pct of slab with little increase in overall solidification time. CONTINUOUS casting has come to the forefront of the steel industry in recent years because of economic advantages resulting from increased yields and elimination of several processing steps. Considerable work, however, remains to be done regarding modifications to the process and operating procedures. Both a lack of operating plants in this country and the experimental difficulties associated with direct measurements on moving castings have made determination of solidification rates and temperature distributions difficult. An alternate approach is to mathematically simulate heat transfer in a continuously cast section, and then calculate the temperature distributions as a function of the controllable variables of the process. Simulation of heat transfer during solidification requires that a nonlinear mathematical problem be solved. As pointed out by Ruddle,' there are two mathematical approaches to the problem- the analytical approach and the numerical approach. While the analytical approach is certainly the more elegant of the two, it does require a number of inexact assumptions because of the complexity of the problem. For example, noteworthy analytical treatments of heat transfer in continuous casting have been developed by Savage Hills,3 and pehlke4 only by making one or more simplifying assumptions such as invariant thermophysical properties, constant heat-transfer coefficients in the mold, and linear temperature profiles in the shell. Simplifying assumptions such as these can introduce considerable uncertainty in the validity of results calculated with analytical solutions. Numerical solutions, which are considerably more versatile, appear to be better suited for solving solidification problems. Complex variations in the boundary conditions and variable thermophysical properties can be handled readily with this technique. Whereas numerical computations can be long and tedious when done by hand, results can now be obtained quite rapidly with the use of either the digital or analog computer. Several numerical models of heat transfer in continuous casting have been published. In 1963, Adenis, Coats, and Ragones published a numerical model used to calculate temperature distributions in direct-chill-cast magnesium billets. More recently, Donaldson and Hess 6 presented results obtained with a numerical computer model of heat transfer in continuously cast steel billets. In the present study, a model of unidimensional heat transfer in continuously cast slabs is presented. The method of solution on a digital computer is also included. Calculated temperature distributions and solidification profiles for various schemes of secondary cooling along with attempts to verify the model are also discussed. MATHEMATICAL MODEL The schematic representation of the slab continuous casting process in Fig. 1 illustrates that the slab passes through three distinct zones of cooling. Accordingly, the mathematical model consists of three parts: 1) solidification in the mold; 2) solidification in the spray cooling zone ; 3) solidification in the radiant cooling zone. Heat-Transfer Equations. The model was developed bymaking a heat balance on a horizontal slice of slab over the time period required for the slice to proceed from the liquid metal meniscus in the mold to the cutoff station. As shown in Fig. 2, the imaginary slice extends from the center line to the surface of the slab. As the slice moves downward, heat is conducted from the center line to the surface of the slab at a rate governed by the surface boundary condition and thermophysical properties of the metal in the slice. The following partial differential equation describes the conduction of heat in a medium moving at velocity U in direction Z:

Jan 1, 1968

[Acker Drill Co., Inc. 997 Bauer Advertising, Inc. Allen -Sherman-Hoff Pump Co. Third Cover Dee Carlton Brown, Advertising Allis-Chalmers Mfg. Co. 911 Compton Advertising, Inc. American Cyanamid Co * James J. McMahon, Inc. American Manganese Steel Div., American Brake Shoe Co. 933 Fuller & Smith & Ross, Inc. Anaconda Copper Mining Co. * Kenyon & Eckhardt Inc. Carlon Products Corp. 910 Penn and Hamaker. Inc.]

Jan 1, 1952

By E. T. Turkdogan, L. J. Martonik, R. J. Fruehan

Electrochemical measuretnents of the solid oxide electrolyte galvanic cells CY-Cr2O3 I ZrO2 (CaO) 1 O (in Fe alloy) CY-Cr2O3 I Tho2 (Y2O3)I O en Fe alloy) have been made at 1600°C (2912°F) in order to test the Performance of such cells at liquid steel temperatures. The oxygen pvobe (cell) consists of a disk of ZrO2 (CaO) or Tho2 (Y2O3) electrolyte fused at one end of a silica tube filled with a mixture of Cr-Cr2O3 which is the reference electrode. Upon immersion in liquid steel, the electromotive force readings achieve a steady value within a few seconds, and remain steady for 30 win or more. The perforwzance of the probes has been tested using Fe-O, Fe-Si-O, Fe-Cr-O, Fe-V-O, and Fe-Al-O alloys; the oxygen contents of liquid steel derived from the measured electromotive forces are in satisfactory agreement with those determined by arulysis. Use of the probe in the deoxi-datiorz of steel, in laboratory experiments, is discussed. The results indicate that there is insignificant electronic conductivity in ZrO2(CuO) at oxygen activities down to those corresponding to 10 ppm in steel. At lower oxygen activities, probes tipped with ThOn (Y2O3) disks perform satisfactorily at oxygen activities down to 1 ppm O or less. THE key to the control of deoxidation of steel is a sensing device to measure rapidly the concentration of oxygen in liquid steel in the furnace, ladle or tun-dish at any desired stage of deoxidation. The analysis of the cast steel by the neutron-activation or vacuum-fusion method gives total oxygen as oxide and silicate inclusions. This analysis is important for guidance to steel cleanliness; however, such a postmortem is of little value in the control of deoxidation of liquid steel. At the General Meeting of the American Iron and Steel Institute in New York, 1968, Turkdogan and Fruehan' presented a paper on the preliminary results of the work done in this laboratory on rapid determination of oxygen in steel by an oxygen probe. Details of the work done in this laboratory leading to the development of a galvanic cell for the determination of oxygen in liquid steel, and the results of the tests made are given in this paper. It was through Wagner's contributions, since the early Thirties, to the physical chemistry of semiconductors in general that it ultimately became possible to construct galvanic cells for application at high temperatures. In 1957, Kiukkola and wagner2 successfully demonstrated the use of several solid electrolytes in measuring the free energies of several chemical reactions, in particular, the use of lime-stabilized zir-conia in high-temperature oxidation reactions. Starting 7 years later, a number of papers appeared in the technical literature3-' demonstrating possible applicability of galvanic cells for the determination of oxygen in liquid steel. In the earliest work, Japanese investigators3j4 experimented with various types of reference electrodes, e.g., graphite-saturated liquid iron at 1 atm CO or Ni-NiO mixtures; the results obtained, though promising, were not of sufficient accuracy. Except for the work of Baker and West,6 all other investigators5,7,8 showed that ZrO2(CaO) electrolyte could be used for this purpose. The main part of the galvanic cell used by Fischer and ~ckermann' and by schwerdtfeger7 (the latter work was done in this laboratory), consisted of a ZrO2(CaO) tube, -1 cm ID, closed at one end, with a platinum contact wire fixed mechanically inside the closed end. The tube was flushed with a gas of known oxygen partial pressure, e.g., air, CO-CO2 or H2-CO2 mixtures; gas along with the platinum lead wire served as the reference electrode. The oxygen contents derived from measured electromotive forces agreed reasonably well with the oxygen contents determined by vacuum-fusion analysis. It is evident from recent investigations that the electromotive force technique using a solid oxide electrolyte is fundamentally well suited for the determination of oxygen in liquid steel. However, it is equally clear that the cell arrangement of the type as commonly used is in need of considerable improvement, as it exhibits several shortcomings for industrial and even laboratory use. 1) Because of its size, the zirconia tube, though stabilized, has a poor resistance to thermal shock. 2) Fine pores and microcracks, which are invariably present in zirconia tubes, are detrimental to the satisfactory operation of the cell, particularly when gas reference electrodes are used. 3) Air or carbon dioxide reference electrodes give rise to high electromotive force readings; as a result, the determination of oxygen in steel becomes less accurate. For higher accuracy, the oxygen partial pressure of the reference electrode should be in the range similar to that of oxygen in steel. 4) Even in laboratory experiments, difficulties are experienced when flushing the tube with gases and maintaining the proper gas flow rate. Fischer and Ackermann,' who used air as the reference electrode, reported that when the flow rate was too low, furnace gases would leak into the electrolyte tube, therefore lowering the oxygen potential and measured electromotive force. The required flow rate in order to avoid leakage depended on the tightness of the electrolyte tube which varied with different tubes, thus making it difficult to predict in advance the required flow rate. However, if the flow rate is too high the inside wall of the electrolyte tube would be cooler than the wall

Jan 1, 1970

By George W. Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell-with certainty what mineral rights exist within any area that is not covered by patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go. through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, by $miner of the old school, as of no value. Think of the litigation over rights of possession on the Com-stock lode—12 leading companies involved 'in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service—such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselvesand their money at a safe distance,

Jan 1, 1915

By Henry Rawdon

THE METHOD of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallographists. The usual procedure1,2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas. (chlorine, hydrochloric acid or similar gas) for. a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced' by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being ad-mitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo.

Jan 2, 1920

By Arthur A. Center

HIGH GRADE zinc stocks were reported short early in 1943, but not Prime Western. Maximum production of High Grade was expected to be reached before the middle of the year, and demands of new brass mills were to take all of the increase. In February three premiums (A, B, C) of 2 3/4c. per lb. of zinc in ore were announced to encourage production from high-cost mines, the number of premiums being in proportion to estimates of ore-production costs.

Jan 1, 1944

By Richard Akerman, Frederick Prime Jr

[THE attention now being paid both in this country and Europe the greatest economy in the working of the blast furnace, and the eagerness with which all thoughtful men in the iron business look for any new information which will tend to throw light on this subject, is a quite sufficient excuse for presenting this paper to the American Institute of Mining Engineers.] I. It must be borne in mind that when two bodies unite to form a chemical compound, heat is almost always evolved. In order to

By R. A. David, D. J. Vink, D. L. Katz

A phase diagram showing boundary curve and quantity of liquid in the two-phase region was determined for a mixture of natural gas and natural gasoline in the region of its critical conditions. The temperatures and pressures of phase measurements were in the range of 85 to 212 F. and 1300 to 2600 Ib. per sq. in., respectively, with the critical conditions at 169.5 F. and 2615 Ib. per sq. in. abs. Color phenomena were observed in the region of the boundary curve from 102' to 192 F. Approximate densities of the single-phase and two-phase regions and analysis of the system are included. Boundary curves between the single-phase and the two-phase regions have been determined for several binary mixtures containing hydrocarbons. 2,3,4.6,7,10,11,12,14 These investigators did not report the relative amounts of liquid and vapor within the two-phase region. The equilibrium values obtained from the dew-point and bubble-point data can be used to compute the lines showing percentage of liquid on the pressure-temperature phase diagram8 but the positions of the lines near the critical temperature and pressure are uncertain. Relative amounts of vapor and liquid were obtained for a gasoline and a naphtha1 within the two-phase area but not in the region of the critical temperature and pressure. The bubble-point and dew-point lines, as well as the percentage liquid lines within the two-phase region, were determined by visual observations in glass apparatus. Apparatus An arrangement of the apparatus is given in Fig. 1, showing the Jerguson gauge A with glass windows B. Pressure was supplied by the

Jan 1, 1940

By R. A. David, D. L. Katz, D. J. Vink

A phase diagram showing boundary curve and quantity of liquid in the two-phase region was determined for a mixture of natural gas and natural gasoline in the region of its critical conditions. The temperatures and pressures of phase measurements were in the range of 85 to 212 F. and 1300 to 2600 Ib. per sq. in., respectively, with the critical conditions at 169.5 F. and 2615 Ib. per sq. in. abs. Color phenomena were observed in the region of the boundary curve from 102' to 192 F. Approximate densities of the single-phase and two-phase regions and analysis of the system are included. Boundary curves between the single-phase and the two-phase regions have been determined for several binary mixtures containing hydrocarbons. 2,3,4.6,7,10,11,12,14 These investigators did not report the relative amounts of liquid and vapor within the two-phase region. The equilibrium values obtained from the dew-point and bubble-point data can be used to compute the lines showing percentage of liquid on the pressure-temperature phase diagram8 but the positions of the lines near the critical temperature and pressure are uncertain. Relative amounts of vapor and liquid were obtained for a gasoline and a naphtha1 within the two-phase area but not in the region of the critical temperature and pressure. The bubble-point and dew-point lines, as well as the percentage liquid lines within the two-phase region, were determined by visual observations in glass apparatus. Apparatus An arrangement of the apparatus is given in Fig. 1, showing the Jerguson gauge A with glass windows B. Pressure was supplied by the

Jan 1, 1940

By Richard Akerman

(Translated by FREDERICK PRIME, JR., Professor of Metallurgy in Lafayette College, Easton, Pa.) [THE attention now being paid both in this country and Europe to the greatest economy in the working of the blast furnace, and the eagerness with which all thoughtful men in the iron business look for any new information which will tend to throw light on this sub¬ject, is a quite sufficient excuse for presenting this paper to the Amer¬ican Institute of Mining Engineers.] I. It must be borne in mind that when two bodies unite to form a chemical compound, heat is almost always evolved. In order to

Jan 1, 1873

By Alexandre Mitinsky

The theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,l that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably due to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually assumed, though incorrectly, that the proportional limit is determined by the ultimate strength. In Germany the poin't at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining the elastic limit by alternately loading and unloading the test specimen is a lengthy process and time has in itself a very considerable influence on the results of physical tests.

Jan 1, 1916

By S. C. Carapella, E. A. Peretti

DURING a literature survey of the indium-zinc phase diagram, controversial reports on the composition of the eutectic point were encountered. The value reported in the investigation of Wilson and Perettil and in a later investigation by Valen-tiner' was 4.0 wt pct zinc. The most recent work recorded on this system consisted of an exhaustive survey of alloys by Rhines and Grobe8 in which they indicate a value of 2.8 wt pct zinc for the eutectic composition. To clarify this aspect of the diagram, a series of alloys were prepared by melting the respective constituents in a glass test tube under a covering of mineral oil and slowly cooling the melt in a furnace. The zinc used was Baker's C.P. and had the following analysis: insoluble in H2SO4—0.0l pct; pb—0.001 pct; Fe-—0.001 pct. The indium, which was supplied by the Indium Corporation of America, had a purity of 99.9'7 pet with the following impurities: Cu—0.002 pct; Pb—0.006 pct; Sn—0.01 pct; Zn—0.01 pct. The alloys were prepared for metal-lographic examination using a technique already reported' and a new value of 2.0 ± 0.1 wt pct zinc was observed. An alloy containing 2.00 wt pct zinc was also made by melting the constituents under a vacuum. In both of these methods of alloy preparation the losses can be kept extremely small. Again, the characteristic eutectic structure was obtained, assuring confidence in this value. The accompanying micrographs are presented in support of this point. Fig. la represents an alloy containing 4.00 wt pet zinc, and reveals excess zinc particles, which precludes the value of both Wilson and Peretti, and Valentiner. Fig. lb, gives the structure of an alloy containing 2.2 wt pct zinc, also showing the presence of excess zinc. Fig. lc is a micrograph of a typical structure of the eutectic observed in several sections of the 2.0 wt pct alloy. In the 1.8 pet zinc alloy, fig. id, the definite presence of the primary indium can be noted. From these re-

Jan 1, 1951

By R. G. Grieves, G. Thodos

A method is presented for the accurate calculation of the cricondentherm and cricondenbar pressures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain six and quite possibly any number of components including paraffins, isoparaffins, olefins, acetylenes, naphthenes and aromatics. The approach is similur to that used for calculating critical pressures and cricondentherm and cricondenbar temperatures. The critical pressure, the normal boiling point and the approximate vapor pressure behavior of each component are all that art required. A stepwise culculation procedure is necessary for mixtures containing more than two components. From an analysis of 22 binary systems and 118 mixtures, the average deviation of calculated cricondentherm pressures from reported values is 2.4 per cent. For nine multicomponent mixtures the average deviation is 1 per cent. Considering 19 binary systems and 108 mixtures, the average deviation of calculated cricondenbar pressures from reported values is 1.7 per cent. For 15 multi-component mixtures, the average deviation is 2.2 per cent. INTRODUCTION A knowledge of the phase behavior in the critical region of multicomponent hydrocarbon mixtures is of value both in industrial processing operations and for the optimum operation of gas condensate reservoirs. Accurate methods of calculating the critical temperatures and critical pressures4,6,7,8,9,23 and cricondentherm and cricondenbar temperatures6p10 of multicomponent hydrocarbon mixtures are available in the literature. If the cricondentherm and cricondenbar pressures could be calculated with equal accuracy, the entire phase diagram of a multicomponent hydrocarbon mixture could be well approximated. The work of Etter and Kay6 is limited to systems containing the normal paraffins and has not been tested on systems containing a heavier component than heptane. In addition, the development of their multicomponent equations is based upon a limited number of mixtures containing from three to six components. Silverman and Thodos have considered systems containing both paraffinic and non-paraffinic hydrocarbons, but their correlation is limited to binary systems and is highly inaccurate for methane systems. Eilerts has done extensive work on the cricondenbar pressure; he has produced an excellent correlation for binary systems. However, his procedure for multicomponent mixtures is chiefly useful for highly complex mixtures requiring a knowledge of the vapor-liquid equilibrium behavior of the mixtures; he has not considered the cricondentherm pressure. The objective of this study was the development of an accurate and rapid method for the calculation of the cricondentherm and cricondenbar pressures of multicomponent mixtures containing all types of hydrocarbons and having a wide volatility range. The approach that was adopted is similar to that used by Grieves and Thodos for cricondentherm and cricondenbar temperaturesl0 and for critical pressures.9 However, methane systems had to be considered separately and a modified stepwise calculation procedure was utilized for the cricondertherm pressure. The correlations were developed in a manner similar to those for critical pressures and cricondentherm and cricondenbar temperatures. Based upon binary data reported in the literature it was observed that the ratios of cricondentherm and cricondenbar pressure to the pseudocritical pressure (molar average), pt/ppc and pp/ppc, respectively, in two-component systems depended upon the mole fraction of the low-boiling component and upon the diversity in properties of the two components. A dimensionless boiling-point parameter Tb,/Tb was chosen to represent the diversity in properties of the components. For a binary system, Ti,'is the molar average of the normal boiling points of the two components involved. For a multicomponent system it is either the molar average of the normal boiling points of all of the components involved or the molar average of the normal boiling point of the pure low-boiling component and of the atmospheric boiling point of the low-boiling-free mixture of

Jan 1, 1965