Search Documents

By Robert Williams

A description is given of a double heat treatment of 60-40 brass. Photomicrographs are included to show the changes that take place in the microstructure on reheating the water-quenched specimens. A wide variation in the mechanical properties may be obtained by the described heat-treatment method. ON SEVERAL occasions, when 60-40 brass is first obtained in the beta condition by quenching at about 825° C. and is then reheated, the writers have noticed that recrystallization will take place in the form of twin crystals at the grain boundaries of the original beta crystals. It was, therefore, thought that interesting results would be obtained if this twinning process was studied further, especially as to the temperature at which it first occurs. The material used in the investigation was a bar of extruded muntz metal, 1/2 in. in diameter, and of the following composition: Copper, 60.21 per cent.; zinc, 39.73 per cent.; lead, trace; iron, trace; tin, nil. Specimens I in. in length were sawed from this bar and a hole was drilled into the side of each specimen until it reached the center, and the tip of a platinum-platinum rhodium thermocouple was inserted. A small Hoskins' resistance-type electric furnace was used for heating the specimens. The specimens were first heated at 840°C. for 2 hr. and then quenched in cold water, in order to get the material entirely in the beta state. In every case, in the reheating process, the furnace was brought to the desired temperature before the specimen was introduced. The time occupied in preheating was from 20 to 30 min. By sawing back 1/4 in. on each side of the hole, two parts were obtained from each specimen

Jan 3, 1924

By T. L. Joseph

S. T. Killian (Johnstown, Pa.)—This is one of the finest papers I have read. Tying in stoichiometric calculations with furnace performance and practice is a step which had to be taken sooner or later. The noteworthy difference between Dr. Joseph's type of calculations and regular blast furnace calculations is that the Ib mol system is used as a basis. With the Ib mol system, weights, volumes, and chemical reactions can all be expressed in the same equation. In the paper, wind, ore, flux, and fuel are all expressed as lb or lb mols. Probably Dr. Joseph does not realize it, but the vague word coke appears only twice in the entire paper. Lb of C and Ib mols of C are followed through reactions but the word coke appears only as 1560 lb coke per ton of pig and 1700 lb of coke per ton of iron. Obviously in order to understand furnace reactions, the coke should be expressed as lb or lb mols of C. Furnaces can also be compared more easily. In some respects the paper is too thorough and too complete. The effects of the metalloids reduced into the iron upon the top gases represents a difference of less than 3 pct of the CO formed in the bosh. Due to the completeness of the calculations in relation to the CO/CO2 ratio, this was included and was necessary. However, the exclusion might have enabled more furnace men to follow the lb mol system of calculations through the blast furnace to a better degree. By considering only irons of similar analysis, this part of the calculations might have been omitted. However, if this had been done, total rewriting of the paper later would have been necessary in order to make the work complete as it is now. It also would not have been nearly as authoritative. In the paper, there appears the reaction: H2O + CO ? CO2 + H2 [I] Dr. Joseph states that he did not take this reaction into consideration in any calculations pertaining directly to the paper. The piobable reason- for this is that although it contains all the main reacting top gases except N2, it is rather inflexible since it is monomolecular in relation to each of the reacting gases and does not tie in with the gasification of C. Actually the reactions: H2O + C ? CO + H2 [2] 2H2O + C ? CO2 + H2 [31 and the solution loss reaction: CO2 + c ? 2c0 [41 tend to assume an equilibrium through the reaction: H2O + CO ? CO2 + H2 [I] which should be considered a balancing or equilibrium reaction. Reactions 2, 3 and 4 permit furnace conditions to balance with the CO/CO2 ratio and H2 formation. They tie in with the solution loss. Reaction 1 unites them chemically. Probably the best calculation to make at this time would be to try to find the relative importance of the CO2 from the flux and the H2 in the dilution on an actual furnace gas analysis. For this purpose the Dob-scha-Carnegie-Illinois paper—"Effect of Sized and Sintered Mesabi Iron Ores On Blast Furnace Performance" is chosen. This paper was presented before the blast furnace section of the AIME in 1948. This represents the best large scale furnace operation available to me. Unfortunately the changes were brought about by beneficiation of the burden and not by changes on one burden. In choosing the basis for the calculation in relation to the furnace, 100 mols of dry top sgas is chosen. This leaves something to be desired inasmuch as the nitrogen basis is changing but I believe it will be better understood than any other type and it is the easiest to use.

Jan 1, 1952

By R. E. Allen

ONE of the most unusual oil field engineering accomplishments of the past two years is the development and rapid advance in the directed drilling of wells. Directed drilling as referred to herein is the controlled steering of the drill stem in the required direction to a given location in the oil sand. The deliberate drifting of holes is an act so far removed from what has been considered good drilling practice that all of the old questions of correlation, drillability and production difficulties are revived. Only a few years ago, during the boom days of Seminole and Santa Fe Springs, the crooked-hole problem, as it was then called, occupied a primary position among the topics of the day in the fields of California and the Mid-Continent. The net result of all the discussion and study at that time was the conclusion that oil wells should be drilled with as little deviation from

Jan 1, 1933

Mr. Joseph P. GAZZAM,Germiston, Transvaal, So. Africa (communication to the Secretary*) :—About fourteen years ago, in southeastern Missouri,I used a method for the wet determination of lead which closely resembles the modified sulphate-chromate method described by Mr.. Guess. The principal difference, however, is, that after dissolving the lead chromate in hydrochloric acid, the chromic acid is determined by means of a standard solution of ferrous sulphate. The method, which I believe is still in use in southeastern Missouri, was found to be convenient and accurate for the determination of lead in the ores and various products of the mills and furnaces in that district, but it was never used for complex ores. A number of determinations of lead in mill-tailings were made in the year 1891; a few of these results are given in Table I. Table I.—Determinations of Lead in MilL-Tailings by Wet Assay.

Jan 1, 1905

By J. French Robinson

A review of production in the Eastern District for 1930 is necessarily brief. Drilling operations were curtailed, due to economic conditions, which in turn reduced production. However, in spite of these conditions, there have been a few outstanding developments which surpass any of recent years. The development of a field in Chautauqua and Cattaraugus counties, New York, has been rapid and probably reached its peak of production in 1930. The gas in this field comes from the White Medina Sand (Silurian), at an average depth of 2600 ft. Some of the wells had an open flow of 20,000,000 cu. ft. of gas per day,' with an original rock pressure of 965 pounds2 per square inch. Another area developed during 1930 was the Tyrone field, in Tyrone Township, Schuyler County, New York. This field was discovered 2nd is practically controlled by the Belmont Quadrangle Drilling Corpn. of New York. The production is from the Oriskany Sand (Devonian), which is found at an average depth of 2100 ft. The field covers approximately 2000 acres, and to date has 14 producing gas wells. The largest well had an open flow of 15,000,000 cu. ft. and an original rock pressure of 740 Ib. The gas from this field is impregnated with sulfur, and requires washing before it is marketed. Because little is known of the Oriskany Sand, a brief description may be of interest. This sand outcrops at Oriskany Falls, New York, and has a thickness of 10 to 12 ft. Its texture is coarse grained, it is composed mostly of quartz and is a regularly bedded sandstone. At Yauger's Wood, in Cayuga County, New York, it is exposed and shows a thickness of 26 feet. The discovery of the Tyrone field led to much prospecting in the New York and the northern part of Pennsylvania, and as a result of this search, the Allegany Gas Co. struck a large gas well in Farmington Township, Tioga County, Pennsylvania, which created considerable excitement through the Eastern District. The gas was encountered at a depth of 4010 ft., and tested 20,000,000 cu. ft. open flow, with a shut-in pressure

Jan 1, 1931

US 4,132,635 -In the froth flotation beneficiation of low- grade siliceous iron oxide ore, an aqueous pulp of undeslimed ore is conditioned first with a reagent formed by incorporating a water-soluble polyvalent metal salt into an aqueous solution of sodium silicate and then with oleic acid or other anionic collector and optionally pine 011 or other frother. The conditioned pulp is subjected to flotation to concentrate Iron oxide values in the froth D. C. Yang, assigned to Michigan Technological University Jan 2, 1979 7 pp (209-1 66) Filed 1-1 3-77 (759,094) Drawing below.) [ ] US 4,133,038-In the froth flotation beneficiation of copper sulfide ore or other ores, an aqueous suspension of a mineral sample of uniform grain size and composition is conditioned with a strongly adsorbable collector in an amount which is a fraction of the amount sufficient to create a monomolecular layer on the mineral grains, and the conditioning continued until the entire amount of collector is adsorbed The conditioned pulp is subjected to flotation, the floated particles separated at timed intervals, and the flotation rate coefficient determined. By varying the degree of adsorption in repeated treatments, the dependence of the flotation rate coefficient on the degree of adsorption may be determined A Nieml Jan 2, 1979 10 pp (364-502) Filed 12-7-77 (858,353) Priority Finland, 5-26-75 (75/1,525) Same: British 1,533,723, dated Nov 29, 1978 Same Canadian 1,065,066, dated Oct 23, 1979 US 4,133,746System and method for maintaining substantially steady state conditions in the froth flotation beneficiation of copper ore, molybdenum ore, or other metal ores The mass flow of flotation concentrate from the cell is monitored continuously, and the rate of admission of aeration air into the pulp in the cell is varied inversely with respect to variations in the mass flow control of rougher flotation cells is accomplished with a single valve G W Dopson, assigned to Magma Copper Co Jan 9, 1979 6 pp (209-1) Filed 11- 23-76 (744,306

Jan 1, 1980

By William Greenawalt

The Greenawalt electrolytic copper extraction process is applicable to suitable oxide ores, sulfide ores and concentrates, and low-grade matte. The process is self-sustaining in acid on sulfide ores or concentrates, on mixed ores, on high-grade oxidized ores; and on low-grade oxidized ores the amount of acid to be purchased or manufactured is greatly reduced. The ferric iron is under easy control, and copper may be effectively deposited from solutions of any acid or iron content likely to be used in copper leaching. From 60 to 75 per cent. of the copper may be removed from the solution in passing through the electrolytic department, before returning the solution to the ore. The amount of copper requiring chemical precipitation, from the waste and foul solutions, is only about 5.0 per cent, of the total copper produced, and this 5.0 per cent. is converted into the electrolytic metal in the regular operation of the process. The entire process can be made practically automatic, and can be carried out mechanically. There is no uncertain departure of any kind in the application of the process; no unusual or unproved apparatus is used. EVER since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydro-electric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods.

Jan 1, 1924

By Brian R. Castle, James J. Scott

INTRODUCTION Referring to a ground support system as a 'band-aid' borders on getting cute, but the application of cable slings in U.S. mining is somewhat analogous. Where problems in the roof or rib require additional support, the versatile cable sling is the answer in a variety of conditions. To fully understand how and why cable slings are used today we must briefly review their development history. Much of the thrust over the last five to seven years in ground support fixtures has been the development of hybrid systems. Taking the best of two or more existing roof bolt fixtures and marrying them into a new fixture which exhibits the good characteristics without the bad of the parent systems. Resin point anchored mechanical bolts, continuous threaded rebar bolts, and others have all be- come important fixtures in rock mass stabilization. HYBRID GROUND SUPPORT SYSTEM The cable sling system is also a hybrid, both in its parentage and in its ground support characteristics. See figure 1. Cable slings combine the techniques of cement. grouting high-strength cables, Friction Rock Stabilizers, and truss-like suspension into a versatile and high- strength ground support system. 1/2" high-strength cable is cement grouted in place in a manner similar to pre-

Jan 1, 1983

By Thomas T. Read

EVERYONE engaged in the teaching of mining engineering will, I suppose, agree that the most difficult subject to teach is "Mining Methods." One primary difficulty is that the students taking the course have either had no previous experience in mining, or else they have had; either seeming to be somewhat of a drawback. The students who are unfamiliar with mines find it difficult to visualize underground conditions, as described and illustrated with sketches and maps, while those who have had underground experience seem to 'find it difficult to visualize anything much different from that which they have already seen. This reminds one of the remark about the Presbyterian doctrine of predestination, to the effect that "you are damned ,if you do; and damned if you don't."

Jan 1, 1930

By George C. Lipsey

FOR many years the mining of coal and other minerals occurring in sedimentary formation has been planned according to information obtained by diamond drilling. Placer mines have used churn drills for sampling and estimating deposits, and some metal mines have used the method either wholly or in part. The diamond drill method, therefore, although not entirely new, has come into more prominence in the last few years. Several large-scale developments now being planned or in the production stage have used this method in varying degree. This paper will describe the operations of the Howe Sound Exploration Co., Ltd. at Snow Lake, Manitoba, where a gold mine was developed and equipped for mining and milling wholly on the basis of diamond drilling results. The property has been in operation nearly 3 years, so that results can be compared with the estimates and assumptions made from the diamond drilling. In developing the subject it is necessary to outline as briefly as possible the normal method of mining, from discovery to production stage. Table I sets forth these various stages, the methods of financing, the percentage of total cost, and the relative time interval required for each section of the work. The plan presented in this table cannot be applied to all mining developments, but it gives a basis on which to work. In Stages 2 and 3 the investment is moderate, and if the property does not respond favorably the options or interests can be terminated. Stage 4 represents a sizeable investment, and it is more difficult to drop the property after this part of the operation is completed. Stages 2, 3, and 4 may be repeated several times by diflerent groups or companies before Stage 5 is reached, but when Stage 5 has been started the total capital investment must be provided and there can be no turning back. It will be noted that there is a total of 116 units of investment in the overall cost if one company proceeds with Stages 2, 3, 4, and 5 in order. Stage 4, however, consumes time which is important when markets are being considered. Bringing a property into production when metal prices are low is much more difficult than when the prices are high, and if this stage can be set aside production is attained more quickly. When Stage 4 is eliminated the total becomes 86 units of cost for Stages 2, 3, and 5, but an adjustment of 14 units must be added to Stage 5. These 14 units represent the useable value of Stage 4. Thus Stage 4 represents an investment of 30 units if carried on before Stage 5, but 14 units if included with Stage 5. This is accounted for by the fact that development work can be accomplished more cheaply under Stage 5, since everything that is done is planned on a production basis with permanent services. Stage 4 must of necessity be governed by expenditures, and a great many temporary services, including housing and power plants, must be provided. The prospect shaft is a small one, and drifts,

Jan 1, 1953

By George C. Lipsey

FOR many years the mining of coal and other minerals occurring in sedimentary formation has been planned according to information obtained by diamond drilling. Placer mines have used churn drills for sampling and estimating deposits, and some metal mines have used the method either wholly or in part. The diamond drill method, therefore, although not entirely new, has come into more prominence in the last few years. Several large-scale developments now being planned or in the production stage have used this method in varying degree. This paper will describe the operations of the Howe Sound Exploration Co., Ltd. at Snow Lake, Manitoba, where a gold mine was developed and equipped for mining and milling wholly on the basis of diamond drilling results. The property has been in operation nearly 3 years, so that results can be compared with the estimates and assumptions made from the diamond drilling. In developing the subject it is necessary to outline as briefly as possible the normal method of mining, from discovery to production stage. Table I sets forth these various stages, the methods of financing, the percentage of total cost, and the relative time interval required for each section of the work. The plan presented in this table cannot be applied to all mining developments, but it gives a basis on which to work. In Stages 2 and 3 the investment is moderate, and if the property does not respond favorably the options or interests can be terminated. Stage 4 represents a sizeable investment, and it is more difficult to drop the property after this part of the operation is completed. Stages 2, 3, and 4 may be repeated several times by diflerent groups or companies before Stage 5 is reached, but when Stage 5 has been started the total capital investment must be provided and there can be no turning back. It will be noted that there is a total of 116 units of investment in the overall cost if one company proceeds with Stages 2, 3, 4, and 5 in order. Stage 4, however, consumes time which is important when markets are being considered. Bringing a property into production when metal prices are low is much more difficult than when the prices are high, and if this stage can be set aside production is attained more quickly. When Stage 4 is eliminated the total becomes 86 units of cost for Stages 2, 3, and 5, but an adjustment of 14 units must be added to Stage 5. These 14 units represent the useable value of Stage 4. Thus Stage 4 represents an investment of 30 units if carried on before Stage 5, but 14 units if included with Stage 5. This is accounted for by the fact that development work can be accomplished more cheaply under Stage 5, since everything that is done is planned on a production basis with permanent services. Stage 4 must of necessity be governed by expenditures, and a great many temporary services, including housing and power plants, must be provided. The prospect shaft is a small one, and drifts,

Jan 1, 1953

By Frank Haas

THE public generally has-become aware that there is something wrong with the coal industry and a clamor has arisen for an explanation if not a remedy for this disorder. It is only reasonable that this Institute be looked to for a diagnosis to show the way for some other .agency to prepare the patient for prescription or operation. The subject is extensive, widely diversified, and beyond the efforts of an individual to cover completely; one of the objects of this paper is the initiating of a symposium on the non- technical factors essential to an understanding of the bituminous coal industry. The present condition of the coal industry cannot be described in a few words but, in effect, it resolves itself into a simple statement: The average coal operator is losing money notwithstanding a firm conviction on the part of the consumer that he pays too much for his coal. Without enumerating the many and varied. factors which contribute to this condition, this paper will be devoted to the interrelation of taxation and ownership of coal and its effect on finance

Jan 1, 1930

By R. R. Knuckey

HAVING been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout. the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. DESIGN OF SEPARATOR The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed paddle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the paddles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1943

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By Gareth Thomas

The analysis of Kikuchi pattersns of exct ovientalions from single cryslals and paired Kikuchi lines from single and overlapping crystals is shown to be useful and quanlitalve and is applied to Phase transfovnzcitions including ordering, spinodals, mavten-silic, and nuclealion and growth pyocesses. 112 pinciple, the analysis of exacl orientations enables the crystal system and the Bravais lattice of a crystal to he determined. The advantages of the davk-field imaging technigure for detecting vevy small precipitates are also described. ALTHOUGH Kikuchi electron-diffraction patterns were first observed nearly 40 years ago,' little systematic application seems to have been made of them, until fairly recently during electron microscopy, when their usefulness in contrast experimen and for determining exact orientations8'9 has been pointed out. With the availability of gonio-metric specimen tilting stages it has now become possible to make much wider use of diffraction patterns, particularly the Kikuchi pattern, which is the main subject of this paper. The treatment presented here is not exhaustive but it is hoped that it will stimulate more use of Kikuchi patterns during electron-microscopy investigations. The Kikuchi pattern is formed as a result of Bragg diffraction of the inelastically scattered electrons produced during the interaction of the beam and thick specimens, The important feature of these patterns is that they give an accurate representation of the symmetry of the crystal being investigated, so that it is possible to identify crystal systems and even the Bravais lattice. This means that new structures, e.g., formed in phase transformations, may be identified during normal electron microscopy, so that Kikuchi-pattern analyses considerably extend the uses of the electron microscope. Recent work has also shown that dark-field images are more informative than bright-field images, particularly, for observing small precipitates. The second part of this paper discusses some applications and advantages of dark-field imaging in studies of two-phase systems. 1) DIFFRACTION PATTERNS 1.1) Spot Patterns. Electron-diffraction spot patterns have their limitations because of the importance of the form factor on the intensities and shape of the reciprocal lattice points. Because of the extension of these points into relrods, reflections are possible over a large angular range (+5 deg) and the patterns from thin regions can be complicated because second-layer relrods intersect the reflecting sphere. Spot patterns can thus give only an approximate idea of the crystallography unless the foil is tilted into exact orientation. In this case the spot pattern is symmetrical, with equal numbers of spots on the positive and negative zone directions about the origin. Such cases are necessary for structural analyses and have been used recently to determine the crystal structure of the ordered Ta64C phase." Exact orientation means that the plane of the reciprocal lattice lies exactly normal to the incident beam as shown in Fig. 1(b). It should be noted that in exact orientations the angle of reflection is less than the exact Bragg angle 9 so that the reciprocal lattice points lie to the outside of the sphere, Fig. 1(b). This deviation is denoted by the parameter s and in the usual convention4 s is negative for exact orientations and, of course, zero at the exact reflecting position shown in Fig. l(a). In order to avoid secondary reflections from thickness relrods it is advantageous to work in thicker regions of foils. Diffraction from thick regions may also produce Kikuchi patterns and as dis-

Jan 1, 1965

By A. C. Losekamp, R. M. Fincel, J. B. Conway

TANTALUM like several other metals exhibits a great affinity for or reactivity with certain gases. Tested in atmospheres which are not completely pure this metal becomes contaminated by certain impurities (notably nitrogen, oxygen, and hydrogen) with a resultant change in various properties. Well-known are the drastic changes in hardness, ductility, and electrical resistivity. Also previously recorded are the distortions of the lattice1,2 accompanying the increased content of oxygen and nitrogen in tantalum. This pronounced affinity for certain gases along with the significant property variations thereby produced makes it necessary to observe additional experimental precautions in making various property determinations with tantalum. Some recent measurements of the linear thermal-expansion characteristics of tantalum have made this point quite emphatically. Failure to observe the greatest precautions in reducing the contaminating influence has led to some extremely distorted results. Not only does such operation lead to different heating and cooling curves during the thermal-expansion measurements, but upon cooling to room temperature the sample is found to have suffered a permanent (actually semipermanent since the specimen can be returned to its original length by a 3-hr degassing treatment in vacuum at 2300°C) elongation. In addition, subsequent heatings will not follow the initial heating curve unless the expansion measurements are based on the actual specimen length at the beginning of the heating cycle. These thermal-expansion measurements were made by positioning the specimen horizontally at the longitudinal midpoint of a 20-in.-long, 4-in.-diam resistively heated tungsten tube furnace. The specimens were in the form of 20-mil sheet formed into a sharp U-shape about 0.3 in. in width and 0.3 in. in depth. Fiducial marks in the form of 0.010-in. holes drilled at either end of the 2.5-in.-long sheet specimens were viewed by a paired filar micrometer telescope system mounted on an Invar bar on the top of the furnace. Tests were made in helium with temperatures measured by a Pt/Pt-lORh thermocouple to 1000°C; above 1000°C temperature was measured by means of an optical pyrometer sighted into a black-body hole drilled into the specimen-holding fixture in the vicinity of the specimen. Previous tests with black-body holes drilled in a 0.25-in.-diam rod specimen had confirmed the temperature uniformity between specimens and specimen-holding fixture in this furnace. A typical thermal-expansion curve for arc-cast tantalum in helium is shown in Fig. 1 for the case where no attempt is made to remove all the impurities from the cover-gas atmosphere. The initial heating curve appears smooth and has a shape characteristic of all metals. However, it is known that the sample begins absorbing impurities at temperatures above 1000°C which are sufficient to distort the lattice and lead to specimen lengths which are somewhat larger than would be obtained in the absence of contamination. During the cooling cycle the expansion curve is seen to be significantly different from the heating curve. This is due to the impurity content causing a semipermanent (i.e., permanent until the impurities are removed by vacuum degassing) deformation which will not allow the speci-

Jan 1, 1965

By H. A. Schwartz

FROM time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion1 of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composition: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213° to 1132° C., the latter figure agreeing with Gontermann's data .2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the metastable diagram, from a temperature somewhat below the eutectic freezing point to a temperature below Ar1 and for a graphitic-carbon content from practically nothing to the original total carbon of the specimen (see Fig. 6). More especially we desired to locate the line in the stable diagram corresponding to the Acm line of the metastable system, which is designated by analogy, the Atm line (tm from temper carbon) ; also to determine the location of Aim with respect to Acm toward their lower extremities at Ar1 in order to determine whether or not graphitization is completed by the separation of an iron-carbon eutectoid analagous to pearlite in the iron-cementite system. This would involve further a comparison of the locations of the stable and metastable A1 points.

Jan 8, 1922

By G. M. Gay, R. L. Perrine

This paper describes a method of numerical computation for three-dimensional, unstable, miscible displacement behavior useful for heterogeneous systems, as well as for more ideal conditions. In the method, flow equations are first linearized by a perturbation approach. The basic flow process is separated and a solution for its behavior readily obtained. The remaining problem of deviations from the basic flow caused by non-ideal conditions is then subjected to numerical analysis. Results obtained from use of the method are also presented. Although conditions assumed in the test cal-culations were severe, results show the type of dispersing flow expected and appear quite satisfactory. The method has eliminated or reduced in importance problems of oscillating values near steep fronts, excessive computer smoothing, etc. A unique advantage of the method is that the source of variations from ideal behavior can be observed. ,The one serious drawback results from the algebraic complexity of the perturbation approach, and the need for second-order terms to be retained in calculations of interest. Fewer array points are available and more computer time is required than would be desired. However, these difficulties are also experienced with other approaches to the solution of three-dimensional dispIacement problems. INTRODUCTION Prediction of behavior of the miscible displacement process within a porous medium for any system of engineering importance is plagued by a number of difficulties. With typical fluid properties the displacing fluid has the lower viscosity, and there is a natural tendency toward flow instability. The problem of predicting instability is compounded by the fact that every real system is heterogeneous. Permeability will vary from point to point — not entirely systematically, and yet not in a random fashion leading to a readily defined average. Furthermore, permeability is unlikely to be isotropic. These permeability properties, which are characteristic of any real porous medium, accentuate the effects of flow instability. Another factor to be considered is that flow dispersion accompanies the displacement process in a porous medium. Mechanistically, dispersion is due to the fact that flow between any two points in the medium follows multiple tortuous paths, each characterized by slightly different flow properties. The fact that the coefficient characterizing dispersive properties of the real medium JS a tensor with variable elements complicates matters. Further difficulties arise because the parabolic influence, while not negligible, is small. Thus, there is a tendency toward steep and uneven displacement fronts along which dispersion smoothing must be represented accurately. Yet frequently used numerical analysis schemes may tend toward either instability, oscillation or excessive smoothing, none of which gives the desired accurate picture of flow behavior. Thus, while many experimental and analytical studies of the process have been made, predictions of actual performance are still subject to considerable uncertainty and possible improvement. This paper reports on part of a study which attempts to develop improved methods for solution of the flow equations describing the miscible displacement process. Of necessity, the calculations were performed on a large digital computer. A three-dimensional system is represented, and the coefficients defining dispersion and permeability can be varied in a manner representative of a real system. Because the differential equations are nonlinear, a first step is to linearize them using a perturbation approach. Objective of this approach has been to separate the basic flow which would occur in an ideal system and for which predictions are readily made. Then the numerical analysis, which is necessarily complex, is directed toward solution of the perturbation equations. These equations state how the basic flow is modified

Jan 1, 1967

By J. F. K. Brown, E. E. Roecker

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944