Search Documents

By J. Brent Hiskey

Carefully prepared gold-bearing arsenopyrite samples from different geographical locations were leached in alkaline cyanide solutions using an electro-dissolution technique. Special precautions were taken to utilize monosized and thoroughly characterized samples. The rates of iron, arsenic, gold and silver dissolution were measured as a function of temperature under controlled conditions in sodium cyanide media.

Jan 1, 1989

By Song Ning

The main mineral constituents of phase-transformed chalcopyrite are CuS and FeS2. CuS is more soluble than FeS2 in an acidic CuCl2 solution with presence of excessive NaCl, so that FeS2 could be removed as solid residue from a leached solution. The experimental results showed that the efficiency of the copper leaching is heavily determined by the following two factors: a) The degree of the chalcopyrite phase transformation to CuS and FeS2 b)The concentration of Cl during the leaching, specifically whether there is enough excessive Cl existed. I t was found that when the Cl in the solution is not excessive, the slowest step of the leaching is the dissolution of Cu2Cl2.

Jan 1, 2006

By Tang Chaobo

Employing manganese carbonate ore and zinc oxide dust as material, Mn-Zn compound oxide powder for soft magnetic ferrite was prepared by a serial methods, as follows: leaching by using sulfuric acid, removing aluminium and silicon by neutralization and flocculation method, using ammonium bicarbonate to co-precipitating Mn and Zn, calcinations and washing to removing impurity content. The optimal technical condition was obtained by experiments. The difficulty of removing impurity such as Si, Al, Ca, Mg, from leaching solution was solved. The impurity content in the production meets with the preparation standard of high quality soft magnetic ferrite. The compound oxide powder obtained in the experiment was made into lower power loss magnetic ferrite, the quality of magnetic ferrite meet the standard of PC40 which was established by TDK corporation.

Jan 1, 2006

By Doug Halbe

?Many are called, but few are chosen.? The biblical adage applies not only to life, but also to hydrometallurgical processes. There have been, in the past, many outstanding successes with new processes ? and also some dismal failures. What are the odds of success for a new process? When there have been problems, why? What can you do to make sure these problems don?t occur with your process? What effect will a slow startup have on project economics? How do financial institutions ? the people who loan your company money for the project ? feel about new processes and why? Is it possible to predict or estimate the time required to reach design parameters?and if so, how do you sell this estimate to management ? and financial institutions? Probably most important ? when do you start thinking about the answers to these questions?

Jan 1, 2003

By M. J. Collins, L. C. Trytten, K. R. Buban, I. M. Masters

Both pressure leaching of zinc concentrate, in an autoclave, and atmospheric leaching, in stirred tanks, have been employed in the expansion of zinc production at plants employing roast-leach-electrowin technology. These direct leaching methods result in the conversion of the sulphur in the feed to the elemental form, rather than to sulphur dioxide, decoupling zinc production from acid production. Atmospheric and pressure leaching methods are also readily implemented over a wide range of production rates. In choosing the best technology for expansion, capital and operating costs, zinc recovery, byproduct quality and the compatibility of recycle streams with the existing refinery must be compared. Leach testwork with several zinc concentrates using both methods has been performed by Dynatec. Recent results are presented, along with a discussion of their implications for process selection.

Jan 1, 2000

By Reinhold G. Schulze

Thiourea is being applied as an industrial leaching agent for gold and silver only in a few cases. A GIP technique was developed which eliminates most of the obstacles against its use. Omission of an acid treatment and mild conditions for precious metals stripping from the loaded carbon simplifies process conditions in comparison to cyanide CIP technique. Examples are given.

Jan 1, 1989

By H. Fukushima, T. Ohgai, N. Baba

The electrodeposition behavior of Zn and the morphology of the deposited Zn were studied in electrowinning solutions containing polymer additives such as gelatin and polyethylene glycol (PEG). The cathode potential was shifted in a less noble direction and the polarization resistance for Zn deposition increased with increasing concentrations and molecular weights of both gelatin and PEG added to the electrolytic solutions. However, when the molecular weights of these additives exceeded about lxlO4, the cathode was depolarized and the polarization resistance for Zn deposition decreased with increasing molecular weight. The crystal grain size and the (002) orientation of the deposited Zn became smaller when the concentration and molecular weight of the additives increased, and the cathode was polarized.

Jan 1, 2000

By Jae-Woo Ahn

Waste acids containing phosphoric, acetic, nitric and hydrofluoric acid were produced during the etching process of liquid crystal display and semiconductor manufacture. In recent years, the attention on the treatment of industrial waste acids has been increased considerably according to the reinforcement of the environmental regulations as well as the implementation of the economic considerations about the waste acids. Fundamental studies on the separation and regeneration of the mixed waste acids were conducted using Cyanex 923, Tri-octyle phosphate and 2-Ethylhexyl alcohol as an extractant by solvent extraction. It is considered that the extraction of liquid crystal display waste acids with Cyanex 923 and Tri-octyle phosphate, semiconductor waste acids with 2-Ethylhexylalcohol is applicable for the separation and recovery of acid. Finally, the acceptable recycling process from the multi-component waste etching acids was proposed.

Jan 1, 2006

By G. Azimi

Calcium sulphate precipitation, mainly as gypsum, during neutralization of acidic hydrometallurgical process solutions can lead to excessive scaling problems. In this work, a self-consistent fundamental chemical model is presented based on the OLI software platform. The model employs the new Mixed Solvent Electrolyte (MSE) activity coefficient model of OLI. A thermodynamic database has been developed and calibrated on experimental data from metal sulphate solutions. The model predicts very well the solubility of calcium sulphate within a wide temperature range and can be used to assess the scaling potential of a particular process stream composition. The effect of temperature, acidity, and divalent metal concentration on the solubility of calcium sulphate in multi-component process streams is also simulated and discussed.

Jan 1, 2006

By R. W. Lee

The first prototype plant using the Imperial Smelting Process commenced operation in 1950. It is timely therefore to review the developments that have occurred with the process over the past half-century. A major advantage claimed initially for the process was its ability simultaneously to recover zinc and lead from bulk concentrates. This has remained a fundamental advantage, but it has been extended by the increasing treatment of secondary materials containing zinc and lead. This has been facilitated by the development of hot briquetting and tuyere injection. These techniques and their impact on the technology of the operation will be described. The other major advantage claimed for the process was its potential to achieve new levels of productivity in the pyrometallurgical smelting of zinc. This has been realised with operating furnaces producing up to 400 t/d of zinc. The technical developments that have enabled this scale of operation will be reviewed.

Jan 1, 2000

By Ahmet Geveci

In this work it is aimed to assess the plant analytical data which appeared during efforts to decrease the effect of carry-over slag (basic oxygen furnace slag) that can not be prevented to leak during tapping of steel in the ladles. While the amount changes, carry-over slag that escaped to ladle, consists of appreciable amount of reducible oxides (?FetO? and MnO) which act as oxygen source for steel bath. By using aluminum dross, containing %30-35 metallic aluminum, which is a non-recoverable process outcome (discard) for most of the aluminum factories, slag reduction behavior will be analyzed together with other parameters such as reaction time, initial amount of total Fe+MnO, amount of reducing agent and reducing effect of soluble aluminum in steel bath while obtaining a slag composition which promotes higher desulphurization capacity and inclusion removal for liquid steel.

Jan 1, 2006

By K. S. V. L. Narasimhan

Recently developed high energy permanent magnets SmCo5, Sm2Co17, Nd2Fe14B offer an interesting study of magnetic phenomenon. This publication discusses briefly the evolution of these magnets and the origin of the coercive force. Atomized SmCo5 coarse particles (150 to 300 microns) exhibit unusually large coercive force contrary to the experience in cast alloys. A brief discussion of utilization of these magnets into devices is also presented.

Jan 1, 1992

By S. Vellinga, G. H. R. Janssen, C. J. N. Buisman, C. F. M. Copini

Non-ferrous metallurgical plants are often confronted with the need to neutralize bleed streams or effluents containing sulfates. The treatment of these streams could produce large amounts of gypsum. With a biological sulfate-reduction process, the production of gypsum is avoided and the metals can be recovered as sulfides. In this paper, the biological treatment of an industrial stream is presented. The bleed solution from a roaster gas scrubber was treated by means of a two-step process. First, the acid was neutralized with calcine. The resulting zinc sulfate solution was converted to ZnS with bacteria using PAQUES-THIOPAQ® technology. The precipitated ZnS was de-watered to 70 wt% solids, and was returned to the roasters. The quality of the effluent stream complied with the environmental regulations.

Jan 1, 2000

By V. K. Kalyani

The present paper discusses a three layer feed forward artificial neural network (ANN) model, trained using the error back propagation algorithm, has been established to simulate the column flotation circuit used for beneficiation of Sillimanite. Parameters such as superficial air velocity, wash water rate, froth height, % solid, feed velocity, sodium silicate and oleic cid are considered as process operating variables and % yield of Sillimanite is the output of the experiment. The results from the ANN modeling, involving the non linear relationship between inputs and outputs, indicate good agreement with experimental observations. The network model validates the experimentally observed trends. The optimal model parameters in terms of network weights have been estimated and can be used for computing parameters of the process over wide-ranging experimental conditions.

Jan 1, 2006

By Hazoor Singh Sidhu

Materials degradation due to corrosion is the major problem in power generation equipment, gas turbine, fluidized bed combustion, industrial waste incinerators etc. Some super alloys have been developed, but they are unable to have different properties to meet the demand of today?s industry. Therefore, a composite system of a base material providing the necessary mechanical strength with a protective surface layer different in structure and/or chemical composition can be an optimum choice in combining material properties. Thermal spray coating of the components before they put into service by suitable surfacing alloy and with suitable coating method can increase the life of these components several fold. Choice of right coating method and alloy for a particular application is extremely important to get the desired service life. The corrosion of some materials and the role of HVOF thermal spray coatings to counteract the same have been reviewed, with an aim to understand the phenomena along with various applications.

Jan 1, 2006

By John M. Rapkoch

In the continuing search for copper matte converting methods, commercially available and feasible choices remain Peirce-Smith Converters, Hoboken Converters, Mitsubishi Converting, Ausmelt converting, and Outokumpu/Kennecott Solid Matte Oxygen Converting (?Flash Converting?). While each alternative improves on Peirce-Smith Converters? limited fugitive gas capturing capability, the Peirce-Smith Converter is relatively easy and economic to operate and has an unmatched ability to accept valuable but difficult-to-handle material such as scrap anodes and purchased scrap copper. Recent experience with designing, building, and starting up an ISASMELT facility, applied in primary smelting of copper concentrates, has led the authors to speculate on how suitable the ISASMELT process would be for copper converting, given its low fugitive gas release and its ability to accept a variety of feed types. This paper reviews the potential metallurgical challenges posed by converting copper matte in an ISASMELT vessel and considers possible engineering and design challenges posed by the inclusion of this technology into a new or refurbished copper smelter.

Jan 1, 2006

By D. N. Wilson

The potential risks of working with lead have been recognised for centuries, but it is only with the development of sensitive measuring techniques in relatively recent years that it has been possible to establish effective approaches for the monitoring and control of lead exposure. This paper examines the principal control measures employed today - lead in air and lead in blood - and reviews the evolution of numerical standards, with particular reference to the latest understanding of health effects. In addition to lead, a large number of other metals are commonly encountered when producing lead and zinc - both primary and secondary - and the health effects of many of these are discussed. Modern hygiene practices and technologies, which have proved successful in reducing worker exposures, are reviewed. The paper concludes with a look at how exposure standards are likely to change in the near to medium future

Jan 1, 2000

By G. Roy Chaudhury

Adsorption techniques are comparatively low cost and effective for treatment of arsenic contaminated drinking water. Various adsorbents such as alumina, ferrihydrite and manganese ores have been used, but there has been little investigation of modifying the structure of ferrihydrite to improve its adsorptive efficiency of As(III) and As(V). In the present study the incorporation of manganese oxide into the ferrihydrite structure was carried out and the prepared materials used in arsenic adsorption experiments. The compounds were X-ray amorphous, but TGA/DTA and FTIR analysis showed some structural characteristics. Sorption studies reported in this paper indicate the excellent arsenic removal properties of the manganese/iron compounds with a loading capacity of 0.3 mmol/g. Adsorption follows first order kinetics and the results fitted to adsorption and mass transfer models. Arsenic levels in water containing 1 mg/L As(V) were reduced by 50% in 20 minutes and 90% in 60 minutes using 1 g/L manganic ferric oxyhydroxide.

Jan 1, 2003

By A. Mejias, M. A. Garcia, G. Diaz

During 1997 and 1998 two successful zinc feasibility studies, Skorpion and Sanyati, were carried out by Tecnicas Reunidas based on the modified ZINCEX® technology. The technical viability of each project was proved during more than 600 h of continuous running in a pilot plant. The Skorpion zinc project would recover 150,000 t SHG Zn/y from an oxidized zinc ore of a Namibian mine. The economical study showed that the plant would have the lowest production costs in the world. The Sanyati zinc project would treat a bleed from an existing copper refinery in Zimbabwe to recover 5,000 t SHG Zn/y. In the first case the electrowinning cellhouse was supplied by Union Miniere and in the second by Tecnicas Reunidas. This article highlights the pilot plant results and the advantages of the proposed process over conventional zinc production practices.

Jan 1, 2000

By Larry Southwick

In the early 1940's, the Caron ammonia ? ammonia carbonate leach process was used to produce nickel from Mayari ores at the Nicaro plant in Oriente Province, Cuba. While plant operation was generally successful, it was not broadly economical and was shut down. The plant was later restarted in the 1950's and a number of investigations initiated to resolve the more serious operational and performance issues. Processing steps studied included iron reduction (chemistry ? nickel and iron, reductant, equipment), ore variability (homogeneity and consistency of mineral concentrations, serpentine vs. laterite), leach solution strength, nickel recovery (temperature ? reduction and leaching, reoxidation) and a variety of other topics. These studies and their findings will be discussed. Caron himself obtained good results on these ores in the laboratory. They could not be duplicated in the field, the reasons for which will be reviewed. (Note: the ore looked like garden dirt; charcoal made from palm trees was one of the reductants attempted; and ammonia was the leach solution. Mixing the three, so to speak, was to yield nickel.)

Jan 1, 2006