Search Documents

By Pengfei Wang, Guorui Feng

With increase of cover depth, dynamic incidents, such as large gateroad convergences and coal bursts, are frequently encountered when mining deep longwall panels. It would be more adverse due to large inclination of the coal bed. Because of the shearer and armored face conveyor (AFC) sliding downhill, toppling of shields, disconnection of AFC to the stage loader are related to it. Tangshan coal mine is a typical deep, inclined coal mine situated in the east of China. The split-level longwall panel layout is being adopted for mitigating problems above, where tailgate entries of longwall panels are driven below gob edge and along the floor, while headgate entries are driven along the roof. Wire mesh and steel sets have been used empirically for support for tailgates for about a decade, which reduces the tunneling speed. In view of this fact, the paper serves to investigate the proper adjustment of the tailgate locations and to analyze the resulting stress and yield conditions according to support strategy. First, field measurements and observations were carried out. Stress data distributed within surrounding rock mass were obtained, especially within the roof since the roof consists of only a coal sheet with a thickness of 2–4 m. Roof pressure of the tailgate represents the pressure at the gob edge since it is below the gob edge. The convergence data were also collected. Numerical modelling using FLAC3D™ was conducted and validated by side abutment stress data. The double-yield constitutive model was used to simulate the gob. The finalized tailgate layout and design were determined through comparison of three scenarios. The research in this paper can help engineers choose the proper tailgate layout and support strategies for coal mines that are going to adopt a split-level longwall panel layout for mining deep, inclined longwall panels.

Jan 1, 2018

By Christopher Mark

The Analysis of Retreat Mining Pillar Stability (ARMPS) program has been used to evaluate room and pillar retreat mining layouts since it was first released in the mid 1990s. After the Crandall Canyon mine disaster focused attention on the importance of pillar design, ARMPS became an essential component in most Roof Control Plans developed by mine operators. In 2010, NIOSH released ARMPS version 6, which features a ?pressure arch? loading model for deep cover room and pillar mining. NIOSH has also provided general guidance for using ARMPS, including design criteria based on statistical analyses of an extensive case history data base. Many real-world retreat mining scenarios entail mining configurations that ARMPS does not directly address. Some of these situations that the MSHA Roof Control Division (RCD) has encountered in the course of its reviews of more than 100 ?complex and non-typical? plans are ? Unmined pillars are left at the mouth of a retreat panel that function as a ?composite barrier pillar? ? The floor is extracted on retreat, increasing the mining height ? More than one row of bleeder pillars is left in an adjacent, previously mined panel ? A retreat panel is located above or below a gob area in a previously mined seam ? Bleeder pillars are partially extracted on retreat RCD has developed solutions that allow these situations to be fitted into the ARMPS framework, and these are presented in this paper. Also discussed are some of the rules of thumb that have been developed for various input parameters, such as the treatment of inseam rock and slab cuts into solid coal.

Jan 1, 2011

By David H. Tang

Similar massive pillar failures were observed in two underground coal mines with different configurations of mine workings and overburden depths. Finite element models were used to analyze the causes and mechanisms of the pillar failure. The results of the analyses confirms the underground observation. For Case No. 1 the failure of coal pillar is mainly caused by a combined effect of smaller coal pillars under a large overburden and the interaction of multiple seam mining. For Case No. 2, the pillar failure was initiated by the weak roof rock but the ultimate pillar failure was caused by the splitting of pillars into very small size.

Jan 1, 1984

By Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs. Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads. Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

Jan 1, 1999

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coalfields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwall face. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 1, 1999

By Stephen P. Signer

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In sonic cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20.000 microstrain. However, electrical continuity to many gages was lost, and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

Jan 1, 1998

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By Zhaohui Wang, Jiachen Wang

"Effective surrounding rock control is a prerequisite for realizing safe mining in underground longwall faces. In the past three decades, longwall top-coal caving mining (LTCC) and single pass large height longwall mining (SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increase the difficulty of ground control. Longwall face failure is a common problem in underground mining, which is induced due to low strength and high fracture density of the coal seam. Moreover, the stiffness of main components included in the surrounding rock system also greatly influences longwall face instability. Correspondingly, the surrounding rock system is developed for LTCC and SPLL faces in this paper. Mechanical conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata, and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between its ultimate bearing capacity and the load imposed on it. The influence of coal strength, stiffness of the coal seam, roof strata, and hydraulic support, as well as the movement of roof structure, are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.INTRODUCTIONThe concentration of coal mining in China is gradually shifting to the west region, and there are a large number of thick coal seams in the newly formed coal mining area. Therefore, the surrounding rock control problems related to mining of thick coal seams will become the focus of research in the field of mining engineering in the future. There are two kinds of mining methods for thick coal seams in China, including single pass large height longwall mining (SPLL) and longwall top-coal caving mining (LTCC). Both methods can accomplish the goal of excavating the full thickness of thick coal seams at one time. SPLL mining benefits from the improvement of the development level of associated equipment. The appearance of large hydraulic supports and high power shearers ensure that the height protected by the hydraulic supports and the height of the sheared coal are the same as the coal thickness. LTCC mining benefits from mining technology advantages. The thick coal seam is divided into two sub-layers, and the working face is normally installed in the bottom layer, while the top coal is caved under the compressive forces due to mining. Therefore, there is a scraper conveyor at the front of the hydraulic support for transporting the sheared coal and another one at the tail for transporting caved top coal. Both SPLL and LTCC methods realize one-off recovery of thick coal seams."

Jan 1, 2018

By André Zingano

Pillar collapses have been studied for several years and can be classified into two types: nonviolent squeeze or violent pillar collapse, i.e., controlled or uncontrolled pillar collapse. Underground coal mines in Brazil are considered shallow mines, because the overburden thickness varies between 20 and 400 meters. For this reason, the coal pillars should be designed as permanent pillars to avoid subsidence and groundwater problems. In the last two years, various pillar collapses occurred, one being a violent collapse and the others being squeeze collapses. All these collapses were considered massive pillar collapses because many pillars were involved. In the violent pillar collapse case, the width¬to-height (w/h) ratio was less than three; although, the pillar safety factor (SF) was more than 1.3. There was a collapse of about 100 pillars in less than three hours. The objective of this study is to determine the mechanism of pillar collapse for this violent pillar collapse. Convergence monitoring and numerical modeling were applied to combine field data and theory to simulate the pillar collapse. Convergence field measurements introduce the arc-effect behavior for the roof. The results showed that other factors besides pillar geometry caused the pillar failure. Other parameters, mainly dip of the coal seam and presence of fractures and faults may affect the strength and failure mechanism of a pillar.

Jan 1, 2004

By Mark F. Sindelar, Yi Luo, Hua Jiang, Michael T. Shook

"Convergence of roof and floor in underground mine openings is a common occurrence. This convergence not only adversely affects the ability of workers, equipment and supplies to travel through the mine, it also reduces the effectiveness of the mine ventilation system, which is essential for the dilution of methane gas and airborne respirable dust. While installing secondary standing supports to control floor and roof convergence, such supports, by nature, partially obstruct a portion of the airway. These added obstructions inhibit the ability of the ventilation system to operate as efficiently as it could by increasing the resistance in and reducing the cross-sectional area of the airway.This study introduces and demonstrates the benefits of The Eye CAN™ standing roof support, which controls floor and roof convergence and is less obstructive to air flow than conventional wooden cribs. Laboratory findings show that the normal resistance of a supported lined airway is reduced by using this new product from Burrell Mining Products, Inc., while providing the same roof support characteristics of an established product-The CAN®. Load vs. displacement curves generated from laboratory tests demonstrated that this new product behaves with the same roof support characteristics as others in The CAN product family. Ventilation data gathered from a simulated mine entry was then used for computational fluid dynamics (CFD) modeling. The CFD analysis showed an improvement with The Eye CAN versus other accepted forms of standing roof support.This proof-of-concept study suggests that, when using this new product made by Burrell Mining Products, Inc., not only will the convergence from the roof and floor be controlled, but airway resistance will also be reduced.INTRODUCTIONOne of the basic elements of underground mining is the necessity to support the mine roof. It is well-known that easier reserves have been mined so that today's underground mines present challenging conditions. Factors influencing roof support decisions include mine depth, mining method, overburden composition, and agency regulations. Mining engineers, therefore, have to balance three objectives: safety, engineering, and cost. While safety is obviously paramount, and engineering often complements safety, the cost effectiveness of any product, method, or device warrants additional consideration in today's harsh business climate. Avenues for adaptation and improvement are found at the intersection of the three objectives."

Jan 1, 2016

By Gabriel Walton, Sankhaneel Sinha

"Rib failures are a major hazard in underground mining. When pillars are subjected to loading, extensile cracks are generated parallel to the excavation boundary, which can manifest as rib falls. A common mitigation measure is to install supports, especially bolts, normal to the rib surface. The type and spatial distribution of these supports along the pillar is often based on experience rather than comprehensive analysis. Since conducting field experiments is often impractical and expensive, a convenient alternative is to perform 3D numerical modeling. In this study, FLAC3D has been used to capture the interaction of rib bolts and the failure processes governing the stability of pillars. An associated goal is to determine whether, at all, a continuum software is capable of modeling the effect of supports. The modeling involved two important steps: selection of a proper constitutive model, and, explicit simulation of rock bolts. Based on precursory work in the last decade, an S-shaped strength criterion was chosen that can describe the tensile fracture mechanism of rock at low confinement and shear failure mechanism of rock at high confinement. The built-in pile structural element in FLAC3D is a simplified representation of the complete bolt system. Hence, the different components of a rock bolt (i.e., steel, grout, steel-grout interface, and grout-rock interface) have been explicitly modeled within the rock mass and then tested for its ability to replicate the ground-support interaction behavior. INTRODUCTION Rib failure-related hazards and injuries have plagued the mining industry for decades (Mohamed et al., 2016; Iannacchione and Prosser, 1998). In highly stressed environments, excavation parallel cracks are the primary initiators of skin instability. In absence of any support, this failure can indirectly destabilize the excavation by increasing the exposed span of intersections and roadways. Over the last two decades, there have been numerous injuries (fatal and non-fatal) due to rib failures in underground coal/non-coal mines."

Jan 1, 2017

By Christopher J. Brown

"Proper ground stability in gate roads has been a critical aspect of success in longwall mining. In particular, the tailgate has proven to be one of the more active mine areas that needs to be managed (Barczak, Dolinar, and Mucho, 1999). As longwall tailgate support technologies continue to be developed and improved, Strata Worldwide has worked to design and manufacture a revised Propsetter to provide additional support capacity and enable applications at greater mine heights. The support is targeted for tailgate applications; however, it can also be used for roof support in various types of mining environments. This paper describes the design changes for enhancing the support capacity of the Propsetter to more closely align its performance with other support technologies currently being employed in longwall tailgates. Balancing changes to each design aspect of the Propsetter was key to successfully improving the roof support load capacity while maintaining controlled deformation. Increasing the load capacity would allow a mine to improve support efficiency with a smaller, less intrusive support compared to support alternatives and to reduce the cost per foot of supported entry. The target support capacity was 80 to 100 tons at two inches of deformation to more closely match the performance of competing tailgate supports, such as the 24-inch-diameter CAN®. To achieve this goal, changes were made to all design aspects of the Propsetter: diameter, wedge cut depth and angle, pod size, and confinement rings. Test results from the NIOSH Mine Roof Simulator verified that these design changes were successful in increasing the capacity of the Propsetter to the 80- to 100-ton range at two inches of deformation. INTRODUCTION Roof support is one of the most fundamental elements of the underground mining process. As materials are removed from the earth, geological conditions will almost always require some form of roof support to keep the extraction area open and stable. Coal mining environments often experience difficult geological conditions that require both primary and secondary forms of roof support to keep the mining environment safe and economical. The secondary support system serves as additional support in the case the primary support system is inadequate. If designed properly, the secondary support system will also assist in maintaining integrity of the immediate roof beam (Barczak, 2000)."

Jan 1, 2017

By Robert C. Speck

Floor heave or deformation of the mine floor into the mine opening is a problem which has plagued coal mines in this country and others. In mining areas where room and pillar mining is practiced, floor heave generally occurs when the stress applied to the floor material by a coal pillar exceeds the bearing capacity of the floor strata. When the floor strata beneath the coal pillar fail, the pillar moves downward and displaces the material under it. This material, in turn, moves outward and upward into the mine opening (Figure 1). As the underlying materials fail, the load supported by the coal pillar may be transferred to adjacent pillars. If these are marginally stable, they too may become overloaded and push into the floor. Thus, floor heave can spread through a large portion of the mine in a progressive manner. As the pillars push into the floor, differential movement and flexure of the roof strata may cause them to weaken and fail, resulting in subsidence of the ground surface above the mine. This paper describes the problem as it was manifested in the Zeigler Coal Company No. 5 and Murdock room and pillar coal mines near Murdock, Illinois, and reports the results of a U. S. Bureau of Mines- sponsored study conducted by the University of Missouri-Rolla. During the course of the study, floor heave in the two mines hindered the transportation of men, machines, and coal to and from the working mine-face, interrupted ventilation plans, drastically increased roadway maintenance costs, intensified safety and strata control problems, destroyed large pieces of equipment, and, several times, pre- vented access to otherwise minable coal resources. The ultimate objective of the study was to develop one or more simple procedures to allow detection of a potential floor heave problem during the exploration phase of mine design--before initiation of production mining.

Jan 1, 1981

By Craig Byington

The stress-field orientation mapping and analysis (SOMA) technique for determining the operative stress field near mine workings and its relationship to various fracture sets is described using Dickenson-Russell Coal Company's Laurel Mountain mine as an example. Carried to its practical application, this technique ultimately defines the optimal orientation for the mine workings wherein pillars, rather than rock bolts or other roof support methods, dominantly shoulder support of the highest-probability, potential, roof-fall blocks. It also provides a predictive tool describing local variability in rock deformation and in secondary roof support methods. Fracture discontinuities within a rock mass, either as pre¬existing natural fractures or as mining-induced fractures, are uniquely necessary for every brittle-deformation ground failure including roof falls. Prediction and mitigation of roof falls requires quantifying the interaction between the fracture sets and the operative principal-compressive¬ stress-axis orientation (olo). The SOMA technique utilizes the interaction between fractures and 61o, specifically their dilation or closure, to calculate the orientation of 610, and to estimate the orientations of 62o and o3o. A stereonet program is used to organize and statistically analyze the fracture data, and then to determine the optimal orientation for the mine workings. The final step in the SOMA technique involves modeling the Laurel Mountain mine using a 2-D, finite-element, modeling program. This assures that the interpretations regarding the optimal working orientation closely match the deformation features observed in the mine. It also provides a predictive tool describing highly variable stress and strain partitioning, seemingly erratic rock-bolt failures and the interactions between different sets of mine workings within different coal seams. The critical importance of including the fracture sets is well illustrated in the Laurel Mountain mine where the effects of earlier mining of an underlying seam is contrasted in both a fractured and otherwise identical non-fractured model to illustrate the consequences of ignoring fractures in a predictive roof-fall model.

Jan 1, 2004

By Gennaro Marino

Documented case histories are studied where data were found on the initial collapse of the overburden above the longwall panels. Under this scenario, the most controlled conditions exist for assessing the span capacity of the overburden (i.e., before failure the roof spans to fin coal abutments on two to all four sides). In an attempt to correlate theory to field observations, data are used on the overburden lithology, and the depth, width, and face advance of the panel, as well as, the subsidence conditions noted on the surface. The subsidence measured on the surface is used to determine when complete failure in the over- burden rock has occurred.

Jan 1, 1987

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By C. C. White

Much benefit can be achieved by a mining company and a manufacturer if both parties can communicate effectively with each other and assist in product development; mutually beneficial ideas and products will develop. This communication can best be achieved if both parties have the opportunity of having on their respective staffs, specialists whose function is to improve the use of products used in mine development. Although a great wealth of roof control knowledge has long existed among mine operators, until recently there was not an abundance of joint development of roof control material by manufacturers and mine operators. This was perhaps due, in past lean years, to the preoccupation of mine management with other overwhelming problems that arise in mining. Manage¬ment had little time for the lengthy process of product development. Until recently, only a few of the largest mining companies had fulltime personnel devoted to roof control. A bolt manufacturer who is invited to work with an operator's roof control people in developing new material is lucky indeed in that he learns what is wanted and he acquires the benefit of the operator's knowledge and experience. He has only to come up with a satisfactory product at an acceptable price - which is not always easy: The development of new products is usually costly and time consuming, and many new products fall by the wayside. In the case of point anchors, however, this product is here to stay. The advantage of point anchors over mechanical anchors is now a proven fact. This advantage is due to less bleed off and higher ultimate load capacity of the resin point anchors. Point anchored bolts have proven to be superior to fully grouted bolts in many areas. We at Birmingham Bolt Company are fortunate in that we have been involved in joint efforts to develop point anchors with several coal companies from whom excellent advice and direction was received. It is appropriate to mention before continuing that the use of point anchors began in the 1960's in Europe and became widespread only recently in the United States. They fall in two categories, point anchors and combination point anchors. These categories have been defined by the Bureau of Mines as follows: (1) point anchors having 24" of grouted length and (2) combination anchors having 24" or more of grouted length. In the present nomenclature, all are anchored with resin or some sort of cementing compound between the rebar or tensioned element and the wall of the hole. The latest development includes an expansion shell as well as rebar, the purpose of the expansion shell being to facilitate installation without the delay necessary in use of types that require a waiting periond for setting of the resin before tightening. (See figures #1 and #2.

Jan 1, 1982

By Steve P. Signer

A study of rock support interaction mechanics was conducted by the U.S. Bureau of Mines at the Jim Walter Resources No. 7 Mine, Brookwood, AL. Bolt loads and entry deformation were monitored at four sites in a tailgate roadway. Two sites were areas supported by fully grouted resin bolts, and two sites were supported by tensioned bolts that used resin-assisted mechanical anchors. The yield capacity of the tensioned bolts was 37 pct higher than that of the grouted bolts. To monitor loads, instruments were mounted on 16 bolts, which were installed during entry development in the standard bolt pattern. Additional instrumented bolts were installed as supplemental support just prior to the headgate pass of the first longwall. Instruments to measure roof movements included three-point roof extensometers and convergence stations. Readings were taken during section development and as each longwall panel passed the test area. The fully grouted bolts showed localized loads that were higher than loads on the tensioned bolts; however, overall loading magnitudes were similar. Many sections of the fully grouted bolts passed the yield point of the bolt steel (98 kN or 22,000 lb). However, the maximum strain measured at any loca¬tion was 50 pct of the ultimate strain, and there was adequate bolt length to transfer the high loads into the rock. Significant bending was detected at many points along the length of the bolts and seemed to be the most significant mechanism in support-rock interaction. Loads on the tensioned bolts did not exceed the yield point of 160 kN (35,000 lb). Entry deforma¬tion, supplemental bolt loading, and general entry degradation appeared to be slightly less at the tensioned bolt sites. Local geology and in situ horizontal stress were also observed to affect con¬ditions at the test sites.

Jan 1, 1993

By Weijia Guo

With the exploitation of coal resources, a large area of land had been affected by surface subsidence, causing conflicts between man and land to become more conspicuous by the day, affecting the life of general public, and constraining further development of the land. This paper predicts the subsidence areas according to the 10-year mining plan of the Jibei mining district as an example. A plan of environmental management was developed based on sciences and practical economics.

Jan 1, 2006

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010