Search Documents

By Timothy C. Richmond

The Stillwater District is located in south central Montana approximately 75 miles southwest of Billings, the state's largest city. It lies along the northeast front of the Beartooth Mountains and is within the boundaries of the Custer and Gelatin National Forests. The district contains some of the nation's most spectacular mountain scenery. Montana's highest peaks, including 12,799 foot Granite Peak, rise a few miles south of the area. Much of the district is located on a gently undulating plateau which averages 8500 ft. above sea level, broken by hills up to 10,000 feet and slashed by glacially carved canyons, some of which are more than 3,000 feet deep.(Fig. 1) Immediately to the north and east, the land falls away to the Great Plains, stretching unbroken to the Mississippi River. Two major tributaries of the Yellowstone River, the Stillwater and Boulder Rivers, traverse the area and several large streams originate in the district itself. Access to the high mountain country and the adjoining Beartooth Primitive Area is restricted to a few horse and jeep trails continuing from the terminus of improved roads in the bottom of the Stillwater and Boulder Valleys. Hunters, fishermen and cabin owners make intensive use of the area along its improved transportation routes, but hikers seldom venture more than three miles beyond the end of the roads. People from the Billings area are the most frequent visitors.

Jan 1, 1974

By Neil D. Policow

Dewatering of the fine clean coal fraction, - 28 mesh (595 microns) represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the Screen Bowl Centrifuge has offered an economical alternative to filtration/thermal dryer combinations. The performance of Screen Bowl Centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Actual test comparisons with alternative methods show the Screen Bowl Centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1982

By James M. Stauffer

There are many types of filters designed to separate a solid from a liquid, including plate and frame presses, pressure leaf filters, gravity filters and vacuum filters. This discussion will be limited to continuous vacuum filtration and, specifically, to continuous rotary vacuum disc filters, drum filters and horizontal belt filters. The use of vacuum filtration can be advantageous in that: 1. The feed slurry can be delivered to the filter either by gravity or by a simple, inexpensive low pressure pump that only has to overcome the resistance of the feed piping system. 2. The filter equipment does not have to withstand high pressures. Consequently, a wide range of materials of construction, including plastic and fiberglas reinforced polyester (FRP), can be used in the fabrication. 3. After the form time, the filter cake is exposed to the atmosphere and the cake is accessible for further operations such as mechanical or physical dewatering, washing, and sampling on a continuous basis. 4. The discharge of the dewatered solids is continuous for directly feeding to the next operation; for example, a dryer. 5. Various methods of discharge can be fitted to the filter to effect optimum discharge of the dewatered cake solids. The principal of operation of a vacuum filter, regardless of type, is basically the same. The filter incorporates a filter medium supported on a drainage system and arranged so that the mixture to be separated (feed slurry) can be introduced to one side of the filter medium on which the solids are trapped and through which the liquid (filtrate) flows due to the applied vacuum.

Jan 1, 1979

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

By W. Szymanski

The United States contains one of the world's largest reserves of uranium. Domestic production and exploration activities, however, have declined since the early 1980s due to weaker-than-expected growth in nuclear power demand and to foreign competition. The main result has been that more costly and less productive conventional mines and mills have closed. Meanwhile, industry productivity as measured by uranium output per employee has increased threefold since 1980. At the end of 1992, only six plants, all nonconventional, were operating in the United States. Due to cost considerations and increased environmental awareness, any additions to existing capacity are expected to be met through nonconventional in situ leach plants.

Jan 1, 1994

By D. Legg

This is the first in a series of studies commissioned by the European Environment Agency that aim to raise awareness of the use of economic instruments and assess their effectiveness. The emphasis is on sharing good practice and increasing knowledge and understanding across European countries in this emerging policy area. A methodology for evaluating the effectiveness of economic instruments has been developed and this will examine whether the inclusion of economic instruments in complex policy packages can improve the overall performance, particularly as a prevention tool in terms of resource use and waste generation The focus for this initial study is the use of aggregate taxes in four EU countries which include the Czech Republic, Italy, Sweden and the UK so that a range of experiences (e.g. geographical, political etc.) can be included. The findings will be used to inform and influence future policy development in other EEA countries. The methodological approach is divided into two main sections: - Technical analysis, which covers quantitative and qualitative analysis. - Process design, i.e. who should be involved when, where and how. Process design is essential if the full learning benefits are to be gained from the technical analysis, which is the ultimate objective of these evaluations.

Jan 1, 2007

By Jeffrey R. Kelly, Paul M. Kubera, Richard A. Howk

Mixing of solid-liquid slurries is a unit operation that is widely encountered in the minerals processing industry. Applications may range from simple slurry storage in open tanks to complex chemical reaction systems under extreme conditions of temperature and pressure. The specific process requirements dictate both the degree of mixing required and the type of agitation employed to achieve the desired results.' Many continuous-flow process applications feature tanks operating in series to provide a discrete number of stages and a known residence time for the slurry. Because these tanks operate at a constant level in an overflow mode, the mixer must maintain uniform solids concentration and size distribution throughout the tank; failure to achieve uniformity results in accumulation of coarse solids in the tank, ultimately leading to a process or mechanical failure. Downward-pumping, axial-flow mixing impellers are widely employed to produce uniform solids suspension. The specific impeller type, number, size, and power draw is a function of each given situation. The use of high-efficiency, fluid-foil impellers (Figure I) has evolved as a recognized standard for these flow­controlled applications. Recent small-scale experimentation and full-scale experience has demonstrated that, when uniformity is required, capital and operating expense can be minimized by employing an additional upper impeller pumping in the upward direction.

Jan 1, 1995

By Andreas Rubo, Stephen Gos

Over the past couple of decades several endeavours have been made to develop lixiviants with the intention of replacing cyanide in gold leaching. In 1980s these endeavours were largely economically driven, due to cyanide shortages at that time. In more recent times, the driving force has shifted to occupational health and environmental considerations. It is often argued that the high acute toxicity of cyanide alone makes it worthwhile considering to replace it completely by less toxic alternative lixiviants. This has led to having to consider more criteria in the choice of any alternative lixiviants, which have often not been taken into account in the past. The intention of this paper is to review these alternative lixiviants and also review the criteria, which have ultimately led to most of these lixiviants never having found any large scale application, if they passed laboratory stage at all. It is also intended to show, that by handling and treating cyanide in a proper manner, the overall profile for the use of cyanide compared to these alternative lixiviants is very favourable. The question to really be answered is whether there is actually any chemical or process applicable to gold leaching that does not show the high toxicity potential of cyanide and that is still favourable with regard to looking at a broader spectrum of criteria and not only acute toxicity.

Jan 1, 2000

By Victor F. Hollister

This section on case histories of discoveries of volcanic-associated and volcanogenic massive sulfide deposits is divided into a preliminary discussion of models and then into three parts: Kuroko- type, Anyox-type, and shale-hosted. The separation is made to accommodate the use of exploration models, and these may not coincide with genetic models discussed in the literature. The exploration models grew as knowledge was gained concerning ore guides and ore controls in the volcanic-related deposits. The evolution of the genesis of massive sulfide deposits in volcanic terranes from a replacement to a syngenetic hypothesis in the 1950s and 1960s necessitated changes in exploration approaches in ore search. The acceptance of a syngenetic origin for conformable or concordant sulfide masses led to more widespread adoption of stratigraphic ore guides. 'The occurrence of epigenetic stringer ore with and stratigraphically below many conformable massive sulfide deposits did not diminish the importance of stratigraphic ore controls. Proximal conformable sulfide masses were formed near their seafloor hot spring source and normally are underlain by epigenetic sulfides: whereas. distal conformable sulfide masses were deposited away from the hot spring and may have no associated feede; zone. Industry groups that early recognized the syngenetic nature of volcanogenic massive sulfides were responsible for discovery of some of the large and economically significant deposits. Ultimately, the rest of the geological profession accepted the leadership of the early iconoclasts.

Jan 1, 1991

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By T. Good

Twin roll sizers are neither compactly designed machines nor are they configured to accommodate underground mobility; in fact, twin roll sizers leave room for improvement in many aspects of the design. The DRC1200 capitalizes on the weaknesses of these machines to make a more productive, easily maintained, and compact twin roll sizer than current market offerings. These strides were made through the inception of the Hard Rock Extraction System (HRXS), which requires a mobile sizer as part of the system. After use of a third party sizer on the HRXS, potential improvements were evident. These improvements include improved structural design to reduce overall footprint and an optimized design to reduce operating cost.

Feb 23, 2014

By Steve Lloyd, Mary Anne Antonioli, Byron Darnton

The Pegasus Gold/Montana Tunnels Mine is a high­tonnage, low-grade, base and precious metal operation in Jefferson City, Montana. Gold heads are typically 0.02 opt with the dominant gold mineral being a native metal electrum quite rich in silver. Early research and development indicated the ore to be amenable to gravity concentration at a 10 to 14 mesh grind. Although full flow gravity preconcentration was considered as a flowsheet alternative, flotation was chosen as the main recovery process due to its apparent lower cost for capital and operating. At this early juncture, the option or concept of recovering coarse free gold by gravity was deemed unnecessary or irrelevant. The intermittent loss of free gold has been observed in the flotation tailing since mill start up. A comprehensive research program was initiated in 1990 to identify the magnitude of this loss and investigate alternatives for its recovery. Batch and pilot plant testing has ultimately led to a permanent gravity circuit being installed at the cyclone underflow. The circuit is designed to scalp out the liberated coarse gold contained in the ball mill circulating load. The final flowsheet consists of: a pinched sluice to upgrade cyclone underflow; a Tyler doubledeck screen to remove over­size from sluice concentrate; Knelson concentrators for roughing and cleaning of screen undersize; an Eriez wet drum separator to remove tramp metal from Knelson concentrate; a Sweco screen to size Knelson cleaner concentrate for tabling; and a Wilfley table to produce final concentrate for direct melting.

Jan 1, 1992

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By Smart Chika Obiora, Anthony Chukwu

Lead and zinc have been mined for over 90 years in parts of the Lower Benue rift in southeastern Nigeria. However, there has been little interest in the sustainability of the environment and the inhabitants of the host communities. Adverse effects include soil and food crop contamination, lack of education, poor healthcare, unemployment, and no access to potable water. This work suggests practicable mitigation strategies to ameliorate these negative effects and promote environmental sustainability.

Jul 1, 2023

By B. Karatzoglou

The penetration of sustainability principles in business practices has introduced the necessity for a simultaneous integrated assessment of the corporate economic, environmental and social performances. Continuous technological, political and legal evolutions indicate that Sustainable Development (SD) principles will soon have to be implemented in all sectors of the Greek corporate reality, among them in the Mineral and Mining Industry. However, the ultimate criteria for the evaluation of a company?s performance remain its profitability and its market value. Managers, shareholders, financial intermediaries, all alike, emphasize and base their decisions on the various accounting produced ratios of return (ROA, ROE, ROCE, Residual Value) included, or produced by data found, in the financial statements of the companies. This paper offers evidence that the traditional accounting ratios discourage the implementation of investment plans that aim at improving the environmental performance of companies and therefore can be inadequate and misguiding for SD applications. International studies have consistently traced a positive relationship between the environmental performances of firms and their financial positions. Yet, the fact that investors tend to reward proactive companies by increasing their corporate values is disregarded by the return ratios, which usually set up the basis for management rewards and bonuses. The book value of the firm assets and owners? equity from which such ratios are produced diverges strongly from the real corporate value, defined as the traded amount for the stock of a firm. There is an urgent need for an adjustment of the return ratios so that they can record the positive economic impact of a more sustainable attitude and encourage decision makers towards this direction.

Jan 1, 2003

By Kenneth L. Myers

The net balance of the inflow and outflow of water in a tailings storage facility has major economic implications in any large mining and milling operation. In a net precipitation environment it can control the ultimate size and storage capacity of a facility or dictate the need for an expensive treatment and discharge program. In a net evaporation environment it can control the extent of the water rights acquisitions required for makeup water and dictate the number and size of expensive wells and pumping and delivery systems. The elements considered in a water balance analysis include the anticipated production rate, the water content of the slurry used to deliver the tailings, inflow from precipitation and snowmelt, and losses from evaporation and seepage. The mine can exert significant control over only one of these elements: the production rate. All others are subject to considerable uncertainty from month to month and year to year. The traditional approach is to analyze in a spreadsheet environment by making simplifying assumptions and using monthly mean or "average" values for precipitation inflows and evaporation losses. Often the analysis will be repeated with values subjectively assigned to represent a "wet" year or "dry'' year. The probabilistic approach uses the same basic spreadsheet model in conjunction with a probabilistic simulation add-in program allowing probability distributions to be substituted for any of the deterministic variables. The resulting analysis shows the full range of variation possible for each parameter of interest (i.e., available return water, makeup water required, storage, seepage losses) and estimates the exceedance probabilities for each. The potential uses and advantages of the probabilistic approach are discussed.

Jan 1, 1992

The adsorption of gold onto activated carbon in iodide solutions has been studied. The adsorption rates were determined as a function of temperature, salt concentration and pH as well as activated carbon concentration. A kinetic model was also developed for the adsorption. The adsorption rate was believed to be controlled by a mixed mechanism of film diffusion and pore diffusion, but the film diffusion had a major contribution to the overall rate. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1993

By John F. Shea

When tunnel boring machines were first developed, the J. F. Shea Company elected not to use them until some of the bugs were worked out. When we did take the plunge, we learned a great many lessons in tunneling; amongst others, that tunneling with a TBM is more an art than a science. One of the most important factors that contributes to a successful TBM tunnel is the geology. A machine can be designed to handle almost any type of ground; however, if the ground is not uniform, compromises in design must be made to enable the machine to handle the various ground conditions. Even when the geologic formations are well defined, it is still impossible to predict how the formations will react when it is penetrated by a tunnel. This is where the design and performance of a tunnel boring machine runs into trouble. When the reactions are adverse, the contractor is left with three alternatives; park or pull the machine and drive conventional, fight through the formation with no changes, or modify the machine. We have made all three of these choices. The first, on the Tonner Tunnel in Southern California, we encountered an extremely tough sandstone where progress was measured in inches per day. Ultimately, we pulled the machine and drove conventional tunnel. The second, on the Vat Tunnel in Central Utah, another element was added to the geology - water, which we encountered in excess of 1,000 gpm at the heading. It was impossible to adapt the machine to handle this much water, so we have been carrying out a program of grouting ahead of the machine and then driving tunnel with the tunnel boring machine.

Jan 1, 1981

By J. S. Jaspal

Mining of thin coal seams is both difficult and uneconomical. As a result, most of thin-seam coal reserves in the U. S. are not being mined. It is estimated that nearly 910 Gt (K. Unrug, 1985) of coal reserves exist in 355 to 710 mm thick seams. The Bureau is attempting to develop new techniques for mining 150 to 1065 mm thick coal seams. This paper summarizes the research work on existing thin-seam mining techniques, testing on small and full scale physical models of the Bureau slot mining concept, and computer modeling of the full-scale process.

Jan 1, 1992

In west-central England, 183 m (600 ft) below the Cheshire Plain, lie the evaporate remains of an ancient sea. Stratified into nine beds of salt separated by marl bands, the deposit stretches roughly 21 x 12 km (13 x 7.5 miles) and contains reserves of rock salt estimated as high as 400 Gt (440 billion st). The Winsford Salt Works, one of England's largest underground mines, extracts the Cheshire salt and sells it for use as animal feed, for application in de-icing programs, and as a key ingredient in sodium fertilizer production and a variety of other industrial processes. Because road de-icing is an important market, demand for Winsford's salt varies with the severity of British winters. Design capacity is 2.25 Mt/a (2.5 million/year). However, production peaked at 2 Mt (2.2 million st) in 1987. Over the past five years, annual production has averaged 1.6 Mt (1.7 million st). Run-of-mine salt averages 92.5% NaCl, mixed with about 5% marl. The marl was formed by deposition of a reddish dust blown into the Cheshire basin from deserts in what is now central Europe. Association with the marl adds color to the salt, producing tea-colored crystals that resemble unrefined sugar. Adaptation of coal mining systems Rock salt mining in the Winsford district began at least as early as 1682. Mining at the current site dates from 1844 but was shut down from 1892 to 1928. In the early 1900s, a series of catastrophic collapses and floods plagued and ultimately shut down then-active Cheshire brine-salt producers. Subsequently, Winsford reopened and began adapting mechanized underground coal mining systems to rock salt extraction.

Jan 1, 1992