Search Documents

By Ben C. Gerwick

This publication is intended to document recent innovations and technologies that have the best potential for effectively improving the quality of marine foundations while reducing the cost, time and risk of construction. Marine foundations originated in Neolithic times with the Swiss Lake Dwellers who constructed pile-supported houses, safe from invading tribes. The Queen of Babylonia built the first recorded bridge in 1500 BC across the Tigris. The foundations were large flat stones laid on the river bottom. About the same time in India, builders extended their water well techniques to the construction of ?well? foundations in the beds of their rivers. These were really the first open caissons; brick walls were built up in a circular ring while divers excavated sand from the bottom, sometimes at a depth of 100 feet. The Romans extended the clay-filled cribs of the Middle East to shallow cofferdams, which they sealed by underwater concrete made with pozzolanic cement from Mt. Vesuvius.

Jan 1, 2013

By Kyle M. Rollins

To improve our understanding of lateral resistance of pile groups, a series of lateral load tests were performed on a full-scale pile group using both static and dynamic loads. The pile group consisted of nine 0.6 m-diameter steel pipe piles driven into clay. During the static tests, the load was cycled fifteen times to evaluate the drop in lateral resistance that would occur due to repeated loading and the formation of a gap. The peak load typically decreased by about 15% from the initial cycle to the last cycle. The load carried by each pile was also measured and there was a significant drop in resistance for the piles in the trailing row relative to the leading row. The dynamic force was applied using the Statnamic loading system which produced a lateral force of 3500 kN (787 kips) in about 0.1 seconds. In two cases, dynamic loads were applied following application of 15 static load cycles. In these cases, the dynamic lateral resistance was about the same as the static resistance, likely due to gaps around the pile. In three other cases, the dynamic force was applied prior to the cyclic loading. In these cases, the dynamic resistance was 30 to 60% higher than the static resistance. Simplified analyses suggest that the difference in resistance could be attributed to damping produced by the soil surrounding the piles during the virgin loading.

Jan 1, 2002

By Michael Forrest, John Roadifer, Glen Gorski

"The Calaveras Dam Replacement Project (CDRP) requires large disposal sites to store excess excavated materials that could not be utilized for dam construction. Because of access restrictions during design, the disposal site rockfill toe dike area at the edge of the reservoir could not be explored to evaluate soil conditions. As such, the site had to be explored as part of the construction contract. Exploration revealed very soft clay and loose silty sand up to 40 feet thick that would not be able to support the rockfill dike at the toe of a large disposal site fill. Several alternatives were evaluated to stabilize these soils. Based on constructability, cost and risk considerations, cement deep soil mixing (CDSM) was selected as the preferred method of soil stabilization. The challenge was to design and construct the CDSM stabilization to minimize construction delays. A joint effort by the design engineer, construction manager and contractor achieved CDSM stabilization in about three months, from design through completion of construction. A rigorous quality control program included compression testing of both wet grab and cored soil cement samples to demonstrate that specified strength requirements were being achieved.INTRODUCTIONDisposal Site 3 (Figure 1) is one of the primary CDRP disposal sites having a height of 240 feet and a storage capacity of about 2,500,000 cubic yards. An approximately 40-foot-high rockfill dike at the base of the disposal site provides an erosion resistant toe for the disposal site. The rectangular foundation area shown in red was not able to be investigated during design because of access restrictions."

Jan 1, 2015

By Mohamed Hassan, Matthias Seip, Steffen Leppla

In the east of Frankfurt am Main, Germany, a new high-rise building is planned directly next to the river Main. The high-rise building will have a height of about 75 m and will be founded on a Combined Pile-Raft Foundation (CPRF) in the tertiary marl. The new structure will be constructed next to important, sensitive traffic infrastructure. The foundation of the new high-rise building adjoins directly existing historic quay structures, which are more than 100 years old. For analysis of the stability and the serviceability of the heavily eccentric loaded foundation of the new high-rise building and the existing structures and for the investigation of the soil-structure interaction complex three dimensional, non-linear numerical simulations have been carried out. These numerical simulations take into account all geometric and material specific boundary conditions, including the history of the construction of the whole area. The paper introduces into a very complex construction project in which the investigation of the soil-structure interaction has an important role. The three-dimensional numerical simulations are explained and the results are shown.

May 1, 2022

By Bengt H. Fellenius

An upgrading and straightening of a highway included building a bridge across a small river. A routine site investigation was initiated to determine the conditions for designing the foundation of the bridge. The proposed bridge was a two-lane highway bridge in one span with a total length of 30 m (100 ft), as indicated in Fig. 1. It was to be placed about 20 m (66 ft) upstreams of the bridge for the existing highway. The site investigation included one boring at each abutment with soil sampling and in-situ vane testing and placed about halfway up the slope from the small river at ground surface elevation + 54 m. Within the investigated maximum depth of 40 m (130 ft), the soils at both borehole locations consisted of a thin clay crust over a thick deposit of soft sensitive clay with a natural water content of about 70 % and a liquid limit of about 60. The undrained shear strength below the crust was about 20 KPa (400 psf) and increased slightly with depth. The sensitivity was high, about 40.

Jan 1, 1987

By J. S. Ward

In a well-written set of contract documents, the probability of conflicts arising during the course of construction is minimized. However, no matter how complete may be the technical language in the contract plans and specifications, the possibility always exists that conditions may be found in the field that were not anticipated at the time the design was formulated. In foundation engineering work, this is commonly referred to as "differing site conditions." When such a conflict arises in the field, the most expedient manner of resolution would be for the parties to the contract to meet and to amicably resolve the issues rather than use the long and costly adversarial approach of the litigation system currently prevalent in the United States. This rapid solution to the construction conflict can be accomplished through an alternate dispute resolution technique that includes mandatory discussion, mediation and arbitration to be initiated immediately following the inception of the dispute and to be concluded in not more than 100 calendar days from the time the dispute originated.

Jan 1, 2010

By Richard Shea

Morris-Shea, an Alabama-based deep foundation contractor, is installing foundation piles at the sites of North America's two largest liquefied natural gas (LNG) terminals currently under construction. The contractor has crews working at Venture Global's LNG lique- faction plant in Plaquemines Parish, Louisiana, as well as constructing foundations for the Cheniere Energy Stage 3 Liquefaction Project in Corpus Christi, Texas. This work includes installing ap- proximately 27,000 DeWaal drilled, full displacement, cast-in-place concrete piles to support seven new midscale LNG trains at Cheniere's Texas ter- minal. Deep foundation installation began at Venture Global's Plaquemines facility, located approximately 30 mi (50 km) south of New Orleans, with an initial phase of 24,000 piles. Plans for the Plaquemines LNG terminal include three loading berths on the Mississippi River and four LNG containment tanks. The facility will utilize new pretreatment com- pressors, liquefaction trains and on- site gas turbine power plants to maintain an annual LNG export capacity of nearly 20 million tons (18 million tonnes) per annum. The site's LNG trains are configured in 18 blocks. The contractor is installing piles through an initial 6-20 ft (1.8-6 m) of cement mixed improved soils, which provide a safe work plat- form for equipment to operate on the extremely weak native soils. Drilling continues through soft clay in the subsurface and tips into a stiff clay or dense sand layer. Production piles are drilled to depths up to 124 ft (38 m) below ground surface. The firm is working with engi- neering, procurement and construction contractor KZJV, a Kellogg Brown & Root and Zachry joint venture, at the Louisi- ana location. The foundation team mobilized at the Plaquemines site in May 2022, to install 16, 18 and 24 in (400, 450 and 600 mm) diameter test piles to depths of 90 and 120 ft (27 and 36 m). The piling contractor returned in September 2022, to start Phase 1 of the deep foundation project, beginning installation of production piles.

Apr 1, 2023

By Timothy C. Siegel

Drilled displacement piles (also known as augered cast-in-place displacement piles or augured, pressure grouted displacement piles) are installed by the displacement of soil and subsequent placement of fluid cement grout within the evacuated volume. Depending on the soil grain-size characteristics, soil behavior, in situ soil density, pile spacing, and pile diameter, the installation process can result in measurable densification and an increase in lateral stress. This paper examines the conditions prior to and following the installation of drilled displacement piles at sandy sites using the cone penetration test. The data support that the installation of drilled displacement piles results in a substantial increase in tip resistance.

Jan 1, 2007

By Lois G. Schwarz

I did not make studies about this parameter but I can say that some researchers recommend using low C3A cements to repair masonry mortar in order to reduce a possible combination with sulphate that can be present in old mortars.

Feb 10, 2003

By Yan Lap J. Kan

"A waterfront stabilization system consisting of Deep Soil Mixing (DSM) columns, vinyl sheet pile fascia, and concrete flood walls supported on shallow footings was designed and constructed for a high-density waterfront development in Northern California. The project site is underlain by soft, compressible organic soil locally known as Bay Mud that has been capped with loose sand and imported fill. The waterfront stabilization system constructed at the site mitigates liquefaction, consolidation settlement and seismic potential slope deformation along the waterfront; the system was designed to reduce lateral displacements to tolerable amounts for the proposed structures. This paper presents the general design methodologies, construction challenges and quality control of this waterfront stabilization system.INTRODUCTIONUrban development in Northern California is fueling innovations in geotechnical engineering as more complex sites are developed. ENGEO Incorporated introduced a deep soil mixing technology from Japan to the US and designed a waterfront stabilization system for a high density waterfront development project in Redwood City, California. The approximately 12½-acre project site, as shown on Fig. 1, is surrounded by water on three sides, with an inner marina at the center of the site.The project site is located in the seismically active San Francisco Bay Area in California. The San Andreas Fault, the Monte Vista-Shannon Fault, the Hayward Fault and the San Gregorio Fault are major active faults located within 25 miles of the site. Once a former marshland with a major slough until the late 1950s, the site was reclaimed by placing imported fill over the native compressible clay deposits, locally known as Bay Mud."

Jan 1, 2016

By David R. Black

Foundation problems due to collapsible and expansive soils are well known throughout the arid western United States. Millions of dollars are spent annually to counteract the effects of such soils for both new foundations and existing foundations suffering from settlement or heave. Over the last 20 years helical screw piles have come into wide-spread use as a permanent deep foundation element for these problem soils, especially in the arid western United States where, in some areas, they are a standard of practice. Independent research resulting in recognition by every national building code in the United States has legitimized helical screw pile technology. Once thought of in terms of light structural underpinning, helical screw piles of today are designed to take heavy structural loads, vertical and lateral, tension or compression, including seismic loads. With proper pile grouping, design capacities for column loads over 4,500 kN (1,000 kips) are attainable. This paper discusses design considerations specifically dealing with collapsible and expansive soils: soil investigation parameters, predicted settlement and long-term creep, heave in expansive soils, downdrag in collapsible soils, shaft slenderness buckling, maintaining shaft alignment during installation, refusal condition, water migration along the shaft, lateral loading, cyclical loading for seismic loads and machine foundations, corrosion, helix durability during installation, the installation torque vs. capacity equation, and design methodology. The paper concludes with several case histories where helical screw piles were used for new structural foundations and to underpin existing failed foundations in St. George, Utah, Cedar City, Utah, and Denver, Colorado, USA, sites of some of the most expansive clay and collapsible soil in North America. Soil descriptions and performance histories are presented.

Jan 1, 2002

By Tim Siegel, III Fondren, Billy Camp

"INTRODUCTIONThe new $650 million power block at Santee Cooper’s Cross Generating Station in Cross, South Carolina is being constructed on driven pre-stressed concrete (PSC) piles. S&ME, as geotechnical subconsultant to Parsons Energy and Chemical Group, was responsible for pile analysis and design to meet the site’s geotechnical and seismic challenges. Selection, analysis and design of the PSC piles included consideration of the following:• Column and equipment support loads ranging up to 500 to 1000 kips (2224 to 4448 kN).• Incorporation of the 2000 International Building Code seismic provisions.• A thick upper soft clay and loose, liquefiable sand.• Potential for karst-related features in the calcareous Santee Limestone.GEOTECHNICAL CHARACTERIZATIONThe near-surface site geology consists of (in order of increasing depth): (1) Pleistocene sediments, (2) the Santee Limestone (considered part of the Orangeburg Group) of Eocene age, and (3) the Black Mingo Formation of the Eocene/Paleocene age (refer to the shear-wave profile in Figure 4). Pleistocene clays and silts are generally soft and will settle significantly if subjected to loading by heavy grade-supported structures while the interbedded sands are generally loose. Where submerged below the shallow groundwater table, the sands were determined to be liquefiable during a strong earthquake.The Santee Limestone is a nearly white to yellow fossiliferous and partly glauconitic rock consisting chiefly of calcium carbonate. Observations of the rock core samples from the site indicate that it can range from hard crystalline limestone (primarily in thin layers) to a lightly cemented sand. In terms of rock strength, the Santee Limestone is generally very soft to soft, depending on the cementation and other depositional characteristics."

Jan 1, 2004

By Heman Manchanda, Jyoti Agarwal

Several infrastructure projects are under construction in India; many of them involves construction of deep foundations like reinforced concrete and steel piles to support super structures. As most of the piles being constructed in India are reinforced concrete bored piles, there are always uncertainties relating to the quality of construction, and in this case non-destructive methods to ascertain quality of piles becomes very crucial to success of any project. Non-destructive pile testing is becoming more and more popular with growing technologies wherein geophysical techniques and wave propagation theories are being used for pile quality and length analysis. Low-strain pulse echo method and cross-hole sonic logging testing are two pile integrity testing techniques being currently practiced in India which are cost effective and provides reliable near accurate results if analyzed properly. Paper presents current practices being adopted in India for conducting these two tests, highlighting the critical site considerations and analysis techniques. The paper also discusses various execution and interpretation challenges faced by practicing engineers and recommends a way forward.

Sep 1, 2022

By Dennis Nottingham

Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971 L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers' experiments, observations and measurements, led to an "H" pile probe design which has produced measured soil density improvements up to 250% using SPT "N60" values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern "Open Cell" bulkhead projects will be presented and discussed.

Jan 1, 2004

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By K. Rainer Massarsch

"Part 2 of 2 (Continued from Summer 2004 edition) By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenVibrations, which are caused by the installation of piles in dry or permeable soils, can cause settlements. The magnitude of settlements depends on several factors, such as soil type and stratification, ground water conditions (degree of saturation), pile type and method of pile installation (driving energy). A method of settlement prediction due to construction-induced vibrations has been presented by Massarsch (2000). However, in many cases, an engineering assessment must be made at an early stage of a project. The following simplified procedure can be used to estimate settlements in a homogeneous sand deposit adjacent to a single pile, Fig. 5. This approach is based on extensive experience from soil compaction projects. It is assumed that intense densification due to pile penetration occurs within a zone corresponding to three pile diameters. The volume reduction resulting from the propagating vibrations will cause settlements in a cone with an inclination 2V:1H, with the tip at a depth of 6 pile diameters. Thus the settlement trough will extend a distance of 3D+L/2 from the centre of the pile, with maximum settlements at the centre of the pile. Maximum settlements, Smaxand average settlements, Smax can be estimated using the following relationship, choosing an appropriate a value of the soil compression factor, from Table 2.The driving energy depends on the method of pile installation, soil stratification and the pile type. The displacement volume of the installed pile has been neglected. The simplified method is applicable for estimating settlements at the perimeter of a pile group. It should be noted that settlements also occur outside the assumed cone, but these are often negligible. The effect of incompressible layers should be taken into account by adjusting the effective pile length."

Jan 1, 2004

By P. J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 2010

By Xavier Pita, Alexandre Pinto, António Cristovão, Rui Tomásio

"The cutter soil mixing technology was been applied in Portugal since the last seven years. The aim of this paper is to present the main design and execution criteria, related with both the cofferdam and foundations solutions, using soil-cement panels, reinforced with steel profiles, at the new Leixões Cruise Terminal, located at the Leixões Port, in Portugal. The Terminal building was built with one basement on a marine environment, over very difficult geological and geotechnical conditions, which demanded the use of some unusual and integrated geotechnical solutions. It is also pointed out the importance of the QC/QA, as well as the technical, economic and environmental advantages of the cutter soil mixing technique, comparing with same more conventional solutions.1 INTRODUCTIONThe construction of the new Cruise Terminal at Leixões, main gate of the Atlantic Ocean to the North of Portugal and Spain, as a consequence to the constant increase of the cruise traffic, was a challenge from both the geotechnical and structural point of views, mainly due to very difficult and unusual conditions, ranging from the geological and geotechnical scenario to the existent and under operation Leixões Port infrastructures, mainly the South break water, as well as the existent cruising boarding deck (Figure 1).According to the Terminal Project it was necessary to build one basement below the water table level, including several earth retaining structures in order to allow the excavation works on dry conditions leading to a global cofferdam effect. For this purpose soil - cement panels, using CSM technology, reinforced with steel profiles, micropiles (both for foundation and cut off effect) and the existent sheet piles were used. Also pointed out are the adopted special foundations of a very complex structure, including bored piles and micropiles (Figure 1)."

Jan 1, 2015

By John G. DiGenova

The Allwell Center Ice Arena at Plymouth State University, Plymouth, New Hampshire is located in the flood plain of the Pemigewasset River. To maintain the arena near the level of the surrounding area, foundation design required use of uplift elements to resist hydrostatic loads caused by frequent flood conditions. Soils beneath the arena consisted of very loose to medium dense alluvial deposits overlying thick glaciolacustrine deposits. Bedrock was encountered at depths of 115 feet (35 m) or more. A mat foundation with a sealed building system was developed for the arena to guard against flood events. Several alternatives were investigated to provide uplift capacity for the mat foundation, including the Rammed Aggregate Pier® (RAP) system, driven precast-prestressed concrete piles, driven H-piles, and deep drilled soil/rock anchors. Evaluations indicated that the most cost effective uplift solution was a tension RAP system that developed uplift resistance in the shallow alluvial deposits. A total of 344 55-kip (245-kN) capacity RAP elements were required for the project. The RAPs were designed to resist tensile loads using threaded steel bars. Dual corrosion resistance was provided to the uplift elements by including sacrificial steel and galvanizing the oversized bars and connection plates. A pre-construction test program was conducted on RAP elements drilled to a depth of approximately 25 feet (7.6 m) and installed using various shaft construction procedures and materials. Ten test piers were constructed and six were tested to verify that the piers could resist 200 percent of the design load with measured deflections of less than 1 inch (25 mm). The RAP system also provided improved bearing conditions for the perimeter wall and mat foundations by densifying and stiffening the upper alluvial soils.

Jan 1, 2011

By John S. Pack

The application of square shaft helical piers in expansive soils is a standard of practice in many areas of the United States. Over 20 years of performance monitoring show exceptional performance and economy will result if proper design procedures, specification requirements and installation procedures are followed. This is true for new foundations and the repair of existing foundations, including lightly loaded wood-frame structures on expansive soils. Proper design includes: 1) site geotechnical characterization, 2) pier layout such that each pier is loaded to its maximum design capacity, 3) maximize spans between piers, 4) minimize the number of piers, 5) isolate the structure from the expansive soil with an appropriate void zone below all grade beams, slabs or other components that would otherwise be in soil contact and 6) utilize only single helix piers. Proper specification employs a performance specification that specifies: 1) the design load on each pier with a suitable safety factor, 2) the minimum installation torque, typically 4,000 ft-lbs (5.4 kN-m), or refusal, 3) a minimum pier shaft steel Fy = 70 to 90 ksi (483 to 621 Mpa) and pier helix steel Fy = 80 ksi (552 Mpa), 4) 1.5 to 1.75 inch (38.1 to 44.5 mm) square shafts, 5) smooth shaft surface, 6) the ICC Evaluation Report (ER) number of the manufacturer and 7) the manufacturer ISO 9001 certification for material quality control. Proper installation requires: 1) equipment with sufficient axial compression force (crowd) on the pier shaft so the helix engages the soil and advances to the specified minimum installation torque or refusal, 2) additional specialized techniques for expansive soils and 3) qualified specialty helical pier installation contractors experienced in expansive soils who submit and utilize pier configurations, techniques and equipment that will most effectively and economically meet the specified performance.

Jan 1, 2007