Search Documents

By Paul M. Schuman, Alessandro Bertero, Giuliana A. Zelada, Sharon G. Cranston

Many jet grouted columns were recently installed to create a jet grout-treated soil foundation for an earthen embankment used in a large shoreline stabilization project in the Mystic River in Charlestown, MA. A physical test program was used to determine whether the jet grouting parameters the Contractor selected would meet the design requirements given the local soil variability, including soft river sediments and organic soils. The presence of hydrocarbons encountered in the marine sediments during the test program caused concern that the design strength could not be achieved. The published literature discusses the environmental aspects of jet grouting with hydrocarbons. The literature did not include many studies of the effect on jet grout-treated soil strength for the types and concentration of hydrocarbons encountered on this project. The grout mix, air pressure, and number of passes of jet grouting were varied in a second field test program to determine jet grouting parameters needed to achieve the design strength of columns with hydrocarbons. A geo-probe study was performed to identify the type and concentration of hydrocarbons on the site. With few exceptions, the quality control core samples from the production columns met the design requirements with many strength values far exceeding the design strength. This paper presents the data, and reviews the lessons learned. PROJECT BACKGROUND The Charlestown Bus Garage, located in Cambridge, Massachusetts, is a Massachusetts Bay Transportation Authority (MBTA) bus maintenance facility located on the Mystic River. The site was home to a coal gasification facility before it was developed by the MBTA as a bus garage in 1978. A deadman-anchored steel sheet pile bulkhead wall installed along the Mystic river on the east side of the site supports the site grade at about El. 11 ft (NAVD 1988) (Figure 1).

Jan 1, 2019

By Wanchai Teparaksa

Pile deviation generally can happen after installation of driven pile particularly in soft soil layers. In this case study, all 242 diameter 0.8 m spun piles were deviated from 20 to 820 mm. The large deviation was caused by lateral soil movement in the top very soft clay layer of thickness about 23 m. This very soft marine clay is very sensitive and anisotropic having high water contents of over 120% and low undrained shear strength of 5-10 kN/m2. The remedial works were carried out based on theory of load transfer and soil-structure interaction. All deviated piles were rectified and used as the foundation piles with strictly controlled pile load tests. The construction of a nine-storey building was successfully completed founded on the rectified piles and it has been opened for the service for over two years.

Jan 1, 2002

By Derrick Dasenbrock, Mary C. Nodine, Benjamin Rivers

Up to 50 percent of major infrastructure projects suffer impacts to schedule or cost due to geotechnical issues, many of which correspond to risks related directly or indirectly to the scope and quality of site characterization work. The Federal Highway Administration (FHWA) in coordination with industry organizations seeks to address this issue through Every Day Counts (EDC), a program that identifies and deploys proven, yet underutilized innovations at the project level to save time, money and resources. The A-GaME (Advanced Geotechnical Methods in Exploration) is one of the innovations supported under EDC.

By Jon E. Bischoff

Construction of a secondary clarifier on the banks of Rainy River, Northern Minnesota, required the driving of H-piles 14HP102 to a sloping, very strong bedrock through thick deposits of soft and medium stiff soils. Pile toe protection, APF Hardbite HP 77750, was specified to prevent damage to the pile toe and to enable the pile toe to bite into the bedrock surface. The toe protection worked well for bedrock sloping less than 2H:1V. However, where the bedrock was steeper, the piles experienced damage and failed to reach bearing. In most cases, the also the replacement pile failed. Pile Driving Analyzer measurements showed that on encountering the bedrock, the pile toe reflection, which at first was sound, deteriorated indicating pile toe damage. Extraction for visual inspection showed that the failed piles were bent and had deformed pile shoes. In areas of steeply sloping bedrock and for replacement piles, an alternative shoe, the Scanpile Herkules rock shoe, was employed. This pile shoe proved to be able to secure the pile toe into the rock and to eliminate the problem. The costs of the Herkules rock shoe considering price, shipping, and attaching, were about equal with the Hardbite shoe.

Jan 1, 1993

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2005

By J. H. Qian

China is one of the countries with comparatively wide distribution of soft soil. In the wake of the rapid developement in the national economy and construction, the improvement technique of soft soil foundation has been perfected gradually. At the present, an integrated system of soft soil improvement has formed, features of such a system are shown by the variety of improvement methods, the complement of theoretical study to project practice. This paper summarizes mainly the following methods: lime column, vertical drain, vibroflotation and dynamic consolidation.

Jan 1, 2010

By Ryan Law

Ground energy systems are being installed in increasing numbers in the United Kingdom. This is particularly true in London where planning regulations require larger scale developments to provide at least 10% of their entire energy demands from renewable sources. A common approach has been to use the groundwater from the Chalk aquifer as a source of energy. This paper explains the potential long and short term sustainability problems with groundwater based systems sited in central London (or any other urbanized area). It also outlines an approach to site testing and numerical modelling to ensure that the system functions well throughout its lifetime. This approach is then applied to a project located in central London.

Jan 1, 2008

By Sebastian Fischer, Rolf Katzenbach, Steffen Leppla

"The risk management in the case of liquefaction is one of the most serious and also difficult issues in geotechnical engineering because failure caused by liquefaction is always a sudden failure without ahead indication. For that reason ground improvement technologies for the prevention of liquefaction are necessary. The paper explains the responsible and effective risk management. Methods for the risk management and stabilizing the soil sustainably are described in detail.1. INTRODUCTIONDue to population growing more and more settlement area is needed, which is often including improper regions (e.g. mountain and coast regions) with raised risk of various kinds of disasters. But also in densely populated areas the risk of disasters like landslides can occur. One reason for the raising of risk in densely populated regions can be the opencast mining for raw material production. An essential element of the opencast mining is the loose deposition of the removed overburden, the so-called “overburden dump”. When an opencast mining is running out of the raw material, an opencast hollow remains in landscape. The slope areas of these hollows mostly consist of loose bedded material of the overburden dump. Due to the end of groundwater conservation these loose bedded slope areas are flooded. In consequence the slopes are in extreme danger of becoming liquefied. The result of a liquefaction in these slopes will unavoidably be a slope slide. Such a slope slide can extend up to several hundred meters into the landscape and can move several million cubic meters of material. An upsetting example for such a landslide is the slope failure in the German city of Nachterstedt on July, 18th 2009, which made necessitate remedial measures and also prevention works for the further utilisation of the region. The phenomena of liquefaction is not limited of slopes in series of opencast mining. Especially in regions with a highly appearance of earthquakes the phenomena of liquefaction is well known.2. RISK MANAGEMENTAn essential part for the stability assessment of slope systems is the investigation of sensitivity against liquefaction. In the case of given sensitivity against liquefaction there is no calculation method according to soil mechanics to determine the factor of safety against slope failure. Just for the case that sensitivity against liquefaction is not met, a comparison of the load (effect) E and the resistance R which is the traditional verification of stability against slope failure, can be calculated (Figure 1)."

Jan 1, 2015

By W. Morgan NeSmith

"The DFI ACIP Pile Committee, in conjunction with the Florida DOT, completed an ACIP Pile installation monitoring and performance test program in late 2016 to advance the inclusion of ACIP piles in future specifications for bridges by state agencies. Piles of different diameters were installed for compression, tension and lateral testing, and one pile was extracted for visual inspection. This paper presents the pile installation, non-destructive testing and load test results of the program.INTRODUCTION The Deep Foundations Institute (DFI) Augered Cast-In-Place (ACIP) Pile Committee performed a ACIP pile installation and test program in the fall of 2016 to demonstrate a fully monitored installation of 18-in and 24-in diameter ACIP piles. The program included automated and manual installation monitoring, Thermal Integrity Profiling, compression, tension and lateral load testing (including monitoring of strain gages embedded along the compression pile shaft), and post-testing extraction of an installed pile for visual inspection.PROJECT DETAILS AND FIELD EXPLORATION A general program location map along with an aerial view of the property in Okahumpka FL is shown in Figure 1. Two Cone Penetration Tests (CPT) were performed at initial reaction pile locations R-6 and R-8 (Figures 2 and 3) The results from CPT R-6 indicated very loose soil conditions at depths below 55-ft, indicating potential relic sinkhole conditions. The test layout was subsequently rotated and moved south of CPT R-8.TEST PILE INSTALLATION DETAILS Seven piles were installed to either 40-ft or 60-ft below grade. Thermal Integrity Profile (TIP) wires were installed in all piles but varied to include one wire each attached to a steel center bar or one wire attached to the steel center bar AND four additional wires (each) attached the steel reinforcing cage installed in these piles. Additionally, the 24-in lateral and compression piles had four steel or PVC casings installed next to the TIP wires for testing by thermal probe and/or wire inserted into the casing."

Jan 1, 2017

By Fawad S. Niazi

Analysis of deep foundations in terms of axial capacity has been a topic of great interest in the soil-structure interaction problems. Soil behavior is governed by a series of complex stress-strain changes that occur during pile installation and subsequent loading. Owing to the difficulties and uncertainties on the basis of the soil strength-deformation characteristics, one of the most frequently followed design practice is to refer to the formulae correlating directly the pile axial capacity components of unit base resistance (qb) and unit shaft resistance (fp) to the data collected from cone penetration test (CPT), i.e. to the tip stress (qc or more proper qt), sleeve friction (fs), and shoulder pore water pressure (u2). The elementary basis for such formulations has been the idea of considering cone penetrometer as a mini-pile foundation. This has resulted in plethora of correlative relationships in the past over 60 years. Such correlations, although empirical, have been worked out on the basis of load test results from both instrumented and un-instrumented full scale piles and are able to accommodate many important variables. A quick review of the evolution process and development of such design formulations is presented with a view to propose recommendations for future research directions, where the latest version of CPT i.e. seismic piezocone test (SCPTu) can be used to advance from capacitysingularity to the complete axial pile load–displacement (Q–w) response.

Jan 1, 2013

By Sudhir Kumar Das

"The exorbitant price of the land in the metropolis has restricted the horizontal expansion and compelled the owners, the developers and the engineers to opt for vertical expansion. This has resulted in the construction of high rises by extending floors of the existing buildings and developing the new ones for which deep excavation is a must. The multistoried buildings up to a certain height can be founded on shallow depth if the soil beneath can withstand the load. If not, the soil can be stabilized by the latest improvement technology to change the properties of soil to cater the desired load of the superstructures. By such practice the cost and time of completion of the substructures can be reduced in comparison to the substructures needed for deep excavation.The necessity of deep excavation cannot be ignored to create housings, underground parking lots and the other public amenities for the urban migrants in the metropolis.Although most of the metropolis have underground mapping the developers, before starting excavation should be hundred percent sure about the alignment and depth of the utilities so that the excavators do not snap the same to bring cut in water supply, power lines, telephone lines etc, resulting in hue and cry in the neighborhoods of the metropolis due to no availability of the essential services The building/structures coming on the influence zones of the deep excavation should be monitored in all sequences of excavations. In case of building underground corridors for rail or road through open deep excavation under a traffic road the developers, before commencing excavation should shift/divert the dry and wet utilities coming on the way of excavation to suitable locations. The surface traffic need to be diverted either temporarily to an adjacent alternative road or allowed to pass over a decking built over the trench of excavation for the affected length of construction. The soil support system is necessary longitudinally on the two sides covering the width of trench for building corridors. In case of building substructures of flyovers built at different plots along the alignment of the flyover or a multistoried complex built at an isolated plot, the soil support system would be necessary on all the sides covering the plot of construction.The material of construction of soil support depends on the depth, type of soil and the type of permanent structure to be developed. Probable geo-hazards inviting casualties in the deep excavation projects occur due to caving of soil, leakage of wet utilities, seepage through honey comb concrete surfaces, failure of pump used for dewatering etc. A detailed comprehensive planning, management and determination of the project authority is essential for marginalizing the casualties. These prevent unforeseen expenditure in mitigation and help to control the time and the cost over run of overall project. The engineer at site should be more a professional manager than an engineer at site. He should be conversant with the safety and environment rules and regulations applicable to deep underground projects."

Jan 1, 2015

By Andrew R. Klaetsch, Peter W. Deming

"The Washington Avenue tunnel in Kingston, NY was completed in 1912 to convey combined storm water and sanitary sewage. Over a mile in length, the tunnel was driven almost entirely in bedrock, with the exception of an approximately 170 foot long brick arch segment constructed in soil. About 90 years after the tunnel was put into service, persistent subsidence problems and sinkholes were observed in Washington Avenue above the shield-driven soil tunnel segment, eventually causing the important traffic thoroughfare to be closed. Subsequent tunnel inspections revealed a breach in the brick arch and a significant volume of fine soil within the tunnel. A two-phase remediation program was implemented to control seepage, reduce soil migration, and remedy sinkhole problems. The first phase included in-situ soil densification by vibratory pile probe driving to improve density in shallow sandy soil loosened by ground loss. The second phase included installation of a continuous soilcrete arch structure over and alongside the tunnel, extending to rock or compact glacial till and spanning the length of the soil tunnel segment. Overlapping vertical soilcrete columns were installed through interlayered sandy and clayey silt by jet grouting to form a continuous arch structure, using grout parameters verified by full scale field testing.PROJECT BACKGROUNDThe Washington Avenue tunnel in Kingston, NY (Figure 1) was completed in 1912 to convey combined storm water and sanitary sewage to Rondout Creek by the Board of Water Supply of the City of New York. The tunnel is over a mile in length and constructed primarily in rock. Contract documents indicate the tunnel was designed with a horseshoe shape at least 3 ft wide and 5.5 ft high."

Jan 1, 2016

By Sung-Ryul Kim, Woong-Jong Park, Juhyung Lee, Si-Hoon Lee

"A bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In this study, a series of 1-g model tests were performed to analyze the accumulated rotation of suction bucket foundations under long-term cyclic horizontal loads. The model suction buckets were made to have the embedment ratios of 0.5 and 1. The dry model ground was prepared to have two different soil densities by air-pluviation method. A horizontal cyclic load over 104 cycles was applied varying the loading amplitude. Test results showed that the accumulated rotation of the bucket foundation increased with the increase in the number of cycles and load magnitudes. Based on the model test results, a new equation was proposed to evaluate the accumulated rotation of the bucket foundations in sandy ground under long-term cyclic horizontal loads.INTRODUCTIONRecently, a bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In terms of economy, a bucket foundation has been considered to be an economical foundation type at sea beds where ground condition is clay or medium dense sand.A bucket foundation resembling a bucket is a kind of suction-installed foundation units. It is a skirted steel foundation which is open at the lower end and closed at the upper end by a lid. The embedment depth ratio (L/D) of a bucket foundation is usually less than one. Figure 1 shows an example of a bucket foundation. Offshore wind turbines are subjected to long-term cyclic loading by wind or currents. A bucket foundation is installed in soil grounds, so the long-term cyclic loading may induce the accumulation of soil deformation.In this study, the accumulated rotations of the bucket foundations in sandy ground were investigated under long term cyclic horizontal load. The number of cycles up to 104 cycles was applied varying load magnitude. The accumulated rotations of the bucket foundations in sandy ground were analyzed based on the test results."

Jan 1, 2016

By Aly M. Mohammad

Croton Point Avenue Bridge carries Croton Avenue over Metro-North main tracks at Harmon Rail Yard in Westchester County, New York. The new bridge is 1100 foot long and 36 foot wide nine span structure with three spans continuous units. The spans are steel multi-stringers, composite with concrete deck. The piers are solid wall piers and the foundations are spread footings. During the design of the bridge foundations it was determined that the relatively loose to medium dense sand layer is susceptible to liquefaction under a design earthquake with a seismic coefficient of 0.15g. Several foundation options were considered for the new bridge including both shallow and deep foundations. It was determined that the most cost effective alternative is to use spread footing foundations supported on densified soils. Vibratory probes were utilized to densify the loose to medium dense sand layer and reduce the risk of liquefaction. Densification test sections were performed to determine the optimum spacing for the vibro probes. The test sections included performing piezocone tests before and after the densification to compare the increase in relative density of the sand. In addition, ground surface settlement due to the vibro probes was measured and correlated to the increase of soil relative density. The paper will present the results of the ground improvement method utilized and correlate the spacing of the vibro probes and the increase in relative density and the results of the piezocone tests performed before and after the densification. It was found that the vibro probes are not as effective as thought at shallow depth below the ground surface. It is believed that the results and finding presented in this paper will benefit both the design and construction industries by providing a relatively cost effective means to improve the soils

Jan 1, 2007

By Inc. Pile Dynamics, Daniel S. Belardo, Marcus Galvan, George Piscsalko

Soil nails are often utilized as a temporary or permanent earth retention technique for slope stabilization and for excavation retention for existing or new structures. Soils nails are generally advantageous as installation is relatively rapid and they can be installed beneath existing structures and where site access for equipment is limited. Due to the typically small cross-section of these elements, the inability to inspect the holes prior to grouting/concreting, and the various installation techniques utilized, quality control for assessing the integrity along the entire length is limited. Currently, quality assurance is conducted by load testing to verify the pull out capacity after installation. The load testing is typically done on a small percentage of the total number of soil nails. This paper will provide the results of a demonstration where the new Non-Destructive Test (NDT) method Thermal Integrity Profiling (TIP) was used to access the integrity of several soil nails along their entire lengths. This TIP method has been successfully used for several years to assess the integrity in drilled shafts and ACIP piles. The TIP method assesses the integrity across the entire cross-section and can identify regions where bulges, necks, and insufficient grout/concrete are present. TIP testing can also help assure that the contractor's installation methods are adequate and consistent for the intended design. For the project presented, instrumented Thermal Wire were affixed to the centered tension bars prior to placement in the excavated shafts. Temperature measurements were recorded from the hydration energy generated after grout/concrete placement, capturing the entire heating cycle. Manufactured defects were installed on the center bar at multiple locations. The results and conclusion will be discussed as well as recommendations for future use.

Jan 1, 2017

By Bernhard Bruggaier

Outside the oil and gas industry there is an increasing demand to install big piles for the foundation of ports, bridges, and wind-energy plants. This article introduces the design and techniques in using large MENCK pile driving hammers to install big foundation piles. Piles with a length up to 120 m, an outside diameter of 1.0 m to 3.15 m and weighing between 25t and 400t are being driven for these types of foundations. The required energy lies between 200 and 1700 kNm. Pile driving hammers that bring this amount of energy weigh from 38 to 300t and have a length between 10 and 20 m. Handling these big pile driving hammers requires a crawler crane on land or cranes on floating pontoons or jack-ups when working in water. Possible are either vertical or inclined piles, using a leader for inclinations up to 1:1.7 or up to 1:3 in a free riding version. Project descriptions demonstrate the versatility and practical use of the equipment under diverse operating conditions.

Jan 1, 2002

By Cen Guoji

The foundation of bored pouring concrete pile have been adopted in the bridge engineering of China since early in the sixties. They demonstrated tremendous technical advantage and achieved notable economic benefit. With improvement of bridge technique including construction technique work equipment, design theory, examination in quality and applicable range etc, the pile diameter became bigger and the foundation changed from shallow to deep-water. This paper examples Jiujiang Bridge of Guangdong in China, which is single-tower cable-staged bridge, total length of 1675m, and expouds adopted successfully the foundation of variable section large bored pile (upper part d=3m, central part d=2. 4m and lower part d=2m) on the conditions of complicated technique that the load is tremendous (it require specially to resist 12000 kN ship impact) and the piles have free length 30m. The paper will be to describle design project and construction practice of pile foundation with variable section, and to compare schemes of equal section pile and pile in sinking-well.

Jan 1, 1991

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"In order to achieve tubular pile driving with low noise and low vibration, the Press-in Piling Method has been adopted on many projects. The method utilizes reaction force derived primarily from previously driven piles to push in the next pile into ground. With attachments, the Press-in piling equipment can deal with hard soil as well as difficult site conditions. At West Toronto Diamond Rail Grade Separation Project in Toronto, Canada, the Press-in piling equipment drove more than 500 of 914 mm (36 inches) diameter tube piles in length of 12 to 25 meters (39 to 82 feet) to construct earth-retaining walls for railway grade separation. Myoshoji River Restoration Project in Tokyo, Japan drove some 600 of 1,000mm (39.4 inches) diameter tube pipe sections in length of 11 to 22 meters (36 to 72 feet) by the rotary Press-in piling equipment to increase the flood drainage capacity of an existing river in highly populated area of the city. Both projects exemplify the advantages of the method in urban settings.1. BACKGROUNDThe Press-in Piling Method was invented some forty years ago in Japan, where a very large number of construction projects were causing widespread construction pollution, especially by pile driving work in densely populated areas. The method has been providing solutions for piling projects which could not have been built otherwise due to the noise and vibration impact to the surrounding communities. The method can be used with various types of piles including sheet piles, tubular piles, concrete sheet piles and so on. With high pressure water jet and continuous flight auger attachments, the Press-in piling equipment can deal with dense sand, stiff clay, gravels, boulders and even soft rock without employing a different set of equipment."

Jan 1, 2015

By Garland Likins

The Texas Department of Transportation, now considering using Augered Cast-In-Place (ACIP) Piles (also known as Continuous-Flight-Auger or CFA Piles) in their foundations, awarded a research project to Professor Mike O'Neill at the University of Houston (UH) to study the advantages and potential difficulties with ACIP/CFA piles. ACIP/CFA piles were installed on three sites for UH; they had extra instrumentation and additional measurements by UH staff during installation which are beyond the scope of this paper. Independent visual logging of the pile was done by an experienced inspection firm. The main advantages of ACIP/CFA piles are their speed of installation and their economy. Potential savings are substantial. Disadvantages include an unknown structural condition of the shaft. Inspection is critical, but many simultaneous observations make accurate inspection difficult. Because of resulting uncertainty, many engineers have avoided ACIP/CFA piles in the past.

Jan 1, 1998

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007