Search Documents

By J. Hamada, K. Yamashita, Y. Shigeno, T. Tanikawa

"This paper offers a case history of piled raft foundation in soft ground supporting a twelve-story building in Tokyo. To increase bearing capacity of the soft soil as well as a countermeasure of liquefaction, grid-form deep cement mixing walls (DMWs) were employed with the piled raft. Based on the long-term monitoring results, the ratio of the load carried by the DMWs to the effective structure load after the construction of the raft was estimated to be 0.3 while that carried by the piles was 0.7. In order to clarify the contribution of the DMWs to bearing the structure load, numerical simulation of the settlement and the load sharing among the piles, the DMWs and the unstabilized soil was performed using a three-dimensional finite element model. The results of the numerical simulation agreed well with the measured values, when the Young’s modulus of the DMWs obtained from the unconfined compressive tests was adopted and the shear modulus of the soft soil was reduced to 50% of that at small strains.INTRODUCTIONIn recent years, piled raft foundations have been used in many countries as building foundations. The effectiveness of piled rafts in reducing average and differential settlements has been confirmed not only on favorable ground conditions as shown by Katzenbach et al. (2000), Poulos (2001) and Mandolini et al. (2005), but also on unfavorable ground conditions such as soft clay and/or liquefiable sand using ground improvement technique (Yamashita et al., 2011a; Yamashita et al., 2011b; Yamashita et al. 2013). Grid type ground improvement using the Deep Mixing Method has been applied to sandy ground as a countermeasure of liquefaction to increase liquefaction resistance of unstabilized soil left in the grid walls where its shear deformation during seismic motion is reduced by the confinement effect of the grid walls (Kitazume, 2013). The high applicability of the method was demonstrated in the 1995 Hyogoken-Nambu earthquake and the 2011 off the Pacific coast of Tohoku Earthquake (Tokimatsu et al., 1996; Uchida et al., 2012a; Uchida et al., 2012b).This paper offers a case history of piled raft foundation in soft ground supporting a twelve-story building in Tokyo. To increase bearing capacity of the soft soil as well as a countermeasure of liquefaction, grid-form deep cement mixing walls (DMWs) were employed with the piled raft. First, the results of long-term field monitoring on the settlement and the load sharing among the piles, the DMWs and the unstabilized soil are briefly described. Next, to clarify the contribution of the DMWs to bearing the structure load, the foundation behavior is simulated using a three-dimensional finite element model, and then the results of the numerical simulation are discussed."

Jan 1, 2015

By Tony D. Canale, Anthony Mazzo

"Times Square, arguably one of the best-known destinations in the world, has undergone and continues to undergo a re-development aimed at attracting corporate tenants to the area. Mueser Rutledge Consulting Engineers (MRCE) was involved with the planning, design and construction of the foundations for the Conde Nast and 5 Times Square sites, as well as Times Square Tower. These sites are pictured in Figure 1.This paper will focus on the design and construction of the deep foundations for Times Square Tower that was developed by Boston Properties. PROJECT DESCRIPTIONTimes Square Tower is 47 stories tall, with no setbacks and an overall height to top of crown of 730 feet (222.5m). It has two basement levels extending 30 feet (9m) below grade over the full site. As shown in Figure 1, the structure occupies the entire site and has a footprint of 22,000 square feet (2,044 m2), with a total rentable area of about 1.2 million square feet (111,480 m2). The planned use for the building is office space with retail at the ground level. When completed, Times Square Tower was the final building constructed as part of the Revitalization of Times Square. Due to the site constraints, designing and constructing the foundations was akin to placing the final piece of a puzzle.Times Square Tower provided numerous design and construction challenges that were a result of tight working conditions, heavy column loads, and a compressed schedule.GEOLOGIC SETTING AND SITE HISTORYThe Times Square area is part of the Manhattan Prong called the Manhattan Ridge, a formation of old and durable metamorphosed and folded bedrock, now termed the Hartland Formation. The bedrock generally has a thin soil cover and uneven surface overlain in some areas with a thin mantle of decomposed and/or weathered rock. Overburden soils include glacial and post-glacial deposits and recent fills.Transit improvements have been made in and around the Times Square area since the early 1900’s. The 1, 2 and 3 Subway Lines that run below 7th Avenue were constructed circa 1915 using cut and cover techniques and extend about 28 feet (8.5m) below grade. The N, R, Q & W Subway Lines that run below Broadway were also constructed in 1915 using cut and cover techniques and extend about 38 feet (11.6m) below grade. The 7 Line that runs below 41st Street was constructed later, using both cut-and-cover and tunneling methods as it runs below the other subway structures at a depth of about 55 feet (16.8m) below grade."

Jan 1, 2005

By Anthony T. C. Goh, Zhiye Zhao, Laddu B. Jayasinghe, Hongyuan Zhou, Yilin Gui

"Ground vibrations from blasting are undesirable and they are very short in duration with high principal frequencies and high amplitude. Structural response to that kind of excitations may differ significantly from that generated by lower-frequency earthquake vibrations. In practice, the damage to nearby structures to generated ground vibrations has been controlled by various codes and regulations available. However, the existing vibrations limits are not always applicable, as they depend on the geological conditions of the site and the dynamic characteristics of the structure. This paper investigated the influence of the rock-soil interface on the response of pile foundation to ground-borne vibration from rock blasting, through numerical simulations using finite element software LS-DYNA. It is found that the slope of the rock-soil interface greatly influences the location of damage and the extent of damage on the pile. The bottom of the pile is subjected to a larger blast pressure and stresses are highly concentrated at the pile bottom. Thus, the pile bottom can fail in shear before it reaches its plastic moment capacity.INTRODUCTIONDrilling and blasting is the widely accepted method to large-scale rock breaking activities in civil engineering constructions due to its cost effectiveness, higher efficiency and ability to break hard rock. However, ground vibrations from blasting are undesirable and it can cause damage to nearby structures. In practice, the damage to nearby structures to generated ground vibrations has been controlled by various codes and regulations available. The existing vibration limits are not always applicable, as they depend on the geological conditions of the site and dynamic characteristics of the structure.Pile foundations are commonly used as foundations of high-rise buildings and bridges to transfer the heavy loads from the superstructure above through weak compressible soil strata into deeper, competent soil layers which have adequate capacity to carry these loads. In engineering practice, many piles are normally designed to carry mainly vertical loads and very little lateral loads, as typically the vertical loads (the gravity) are significantly larger than the horizontal loads such as wind loading. However, in recent years, there have been a number of reported case studies of translational soil movements that have induced stresses and bending moments that have damaged pile foundations and in some cases resulted in collapse of the superstructure. Typical lateral load include nearby construction activities such as an excavation for a basement or slope, the construction of a road embankment or a tunnel, as well as earthquakes (Abdoun 1997; Goh et al. 1997; 2003; Chen et al. 1999; Dobry et al. 2003; Boulanger et al. 2007; Black et al. 2007)."

Jan 1, 1900

"Standing 92 stories high and just over 1,362 ft tall, Chicago’s Trump International Hotel and Tower is perfectly positioned at the center of one of the world’s most impressive skylines.The Tower serves as a link between its famous predecessors, Willis Tower (formerly, the Sears Tower) to the south and the John Hancock Building to the north. Originally planned to be the world’s tallest building, the project was scaled back when the developers started questioning the need for super-tall buildings after the September 11, 2001 terrorist attacks. In its River North neighborhood, Trump Tower dominates the skyline as a symbol of Chicago’s last great building boom, standing triumphantly over other high-profile projects that have been postponed due to current economic realities.It is often said that the three most important factors in real estate are location, location and location. This maxim was not forgotten by The Trump Organization when the site was selected for the International Hotel and Tower. Located two blocks west of Michigan Avenue and Chicago’s famed Magnificent Mile, the site is bound by the historic Wrigley Building to the east, Wabash Avenue to the north and west, and the Chicago River to the south. The building’s position along a bend in the Chicago River allows visitors and residents unobstructed views to the mouth of the Chicago River and Lake Michigan. Site ChallengesUnderneath the site there are approximately 10 to 20 ft of sand and urban fill underlain by soft Chicago blue clay. At 75 ft in depth, the soft clay transitions into Chicago hardpan, a very hard till that was consolidated by the glaciers over 10,000 years ago. Below the hardpan, the till turns granular with cobbles, boulders and water under pressure. Bedrock is about 100 ft below existing grade and has a weathered surface with fractures and clay seams. Unweathered limestone bedrock is sound and hard with unconfined compressive strengths of 10,000 to 20,000 psi."

Jan 1, 2009

By Arpana P. Sabu, Themis Vaxevanis, Sissy Nikolaou, Guillermo Diaz-Fanas

Geo-failures from extreme events (landslides, wild fires, earthquakes, floods, etc.) have increased exponentially in recent years around the world and within the USA. When catastrophic failures occur, they usually involve hundreds of fatalities especially in cases of unexpected triggering events, such as large intensity earthquakes or heavy flash floods. Protective actions against identified potential geohazards can mitigate the associated risks and the future occurrences and prevent these occurrences from becoming disasters, targeting the essence of resilience in geotechnical engineering. Imaging and other virtual design and construction tools can be used to identify weaknesses that trigger geohazards and can, in combination with numerical simulations, guide decision making. In spatially distributed problems, 3D visualization and LiDAR-type of technologies are essential in providing geotechnical engineers a deeper understanding of precarious soil zones and support finding appropriate solutions. This paper will present the value of using virtual design and construction technologies though the case study of the Iztapalapa suburb of Mexico, about 20 km southeast of Mexico City. Iztapalapa was developed within irregular topography and has a long history of severe soil subsidence. Following the 2017 Puebla-Morelos earthquake, the town experienced large settlements resulting in extensive damage to the already frail buildings and unregulated infrastructure. The soil subsidence was visualized by mapping available historic and geotechnical data. The visualization helped to identify areas where additional investigations were needed. Additionally, this paper presents a case study of a series of landslides from the 2016 Mw7.8 Muisne Ecuador Earthquake, which demonstrates the advantages of using novel technologies to collect data and create cloud datasets from drones and digital photos to understand and evaluate geo-vulnerabilities in anticipation of an extreme event and during rapid reconnaissance to plan for long-term instrumentation, which can enhance geo-disaster prevention and overall community resilience. INTRODUCTION Iztapalapa is a southeastern borough of Mexico City (CDMX) located within the Mexico Basin (Figure 1). This borough is a densely populated area of CDMX with a total of 1.8 million inhabitants, and has a third of its population living in poverty (Gonzalez-Hernandez et al., 2015) with limited to no access to clean drinking water. Iztapalapa also suffers from high rates of crime, drug trafficking, sex trade and illegal buildings. As the population continues to grow, the already non-regulated and fatigued infrastructure is unable to meet the community needs, especially during and after natural hazard occurrences. The region of CDMX is one of the world’s most seismically active regions that is also exposed to other geo-hazards such as floods, volcanic eruptions, and continuous settlement due to water pumping that has reached 11 meters over the past 100 years (Nikolaou et al, 2019). While the soil subsidence alone has caused significant infrastructure damage in Iztapalapa and throughout the rest of the city, recent earthquakes have also contributed to those damages.

Jan 1, 2019

By Matthew Janes

The new Bow office complex will become the new headquarters of EnCana Corporation, a leading Canadian oil and gas company. The shoring system, encompassing nearly two city blocks and excavated to a depth of 20.5 m, supported surrounding utilities and buildings in downtown Calgary. Past excavations in the area experienced large amounts of rock movement, the mechanics of which were poorly understood. The focus of this paper is the design process and construction results concerning rock movement and the effectiveness of the shoring structure. A lack of information regarding the local in-situ stresses and shear band propagation in the bedrock led to research of case studies in the Calgary area and a peer review from local experts. Several geotechnical scenarios were analyzed using FLAC to account for varying residual rock stresses and the location and composition of weak rock layers suspected of causing shear band movement. Movement characteristics were predicted that would identify the rock deformation mechanic throughout the construction process. A detailed monitoring programme composed of precision monitoring targets, inclinometers, and extensometers was established to provide accuracy and redundancy in establishing the movement of the rock and excavation support structure. The results of the programme were used to identify the rock deformation mechanics and further refine the FLAC analysis. To date, monitoring indicates that localized shear band effect is the leading cause of rock movement. The phenomenon appears to be directionally dependent and strongly correlated to excavation extent.

Jan 1, 2008

By Tsunenobu Nozaki

"Basically, the “Press-in Piling Method” was invented to eliminate construction nuisances, such as noise and vibration which have been serious unsolved problems for advancing societies over a long time. In the construction industry, piling works have been a major cause of noise and vibration, because most piling methods utilize dynamic load to install piles into the ground. The secret of the Press-in Piling Method is to utilize static loading to install pre-formed piles rather than dynamic load. The piles are hydraulically gripped and jacked into the ground by the special piling rig known as the “Silent Piler”. Therefore, the piles can form a robust and firm foundation, which is another advantage of the Press-in Piling Method.The Press-in Piling Mechanism and Implant Foundations The basis of the Press-in Piling Method is simple. The Pres-in Piling Machine installs a preformed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles, which are called “Reaction Piles”. Due to this, the Press-in Piling Machine can produce a powerful piling force whilst only requiring minimal machine size.With the Press-in Piling Method, as piles are pressed into the ground, they are incorporated with the surrounding soils, which provides a large bearing capacity and passive horizontal resistance. These embedded foundations which are firmly anchored into the ground are known as “Implant Foundations”. Being embedded into the ground, the foundations are resilient and maintain their serviceability even in the worst credible design conditions."

Jan 1, 2015

By Javankhoshdel Yacoub

Piles are often used to reinforce slopes as they increase the available restoring force when calculating the factor of safety against sliding. In this paper, a 3D model of a slope containing multiple modes of failure is reinforced using pile elements. The results of the 3D Limit Equilibrium analysis containing piles are obtained using a newly introduced coupled approach which combines the results of finite element analysis (to obtain the displacement of soil along the pile) with the traditional limit equilibrium iterative formulation. The multiple modes of failure are obtained using the novel Multi-Modal Optimization (MMO) metaheuristic method which adapts the Particle Swarm Optimization (PSO) method to search for multiple local minima in a single slope model.

Oct 1, 2022

By A. David Miller, Chika Oya

"Field sampling and testing are part of the Quality Assurance/Quality Control (QA/QC) requirements for all Cement Deep Soil Mixing (CDSM) Projects. Field sampling and testing are also used for determining the performance and quality of soil mixing method(s) and are the primary basis for accepting or rejecting the soil mixing wall among all other QC testing. Two of the most commonly recognized and used sampling methods for CDSM walls are wet grab sampling and verification coring. Depending on the types of wall construction and project budget, one or both of these methods are normally used to help evaluate the in-situ matrix and quality of the mixed soils. Additional to ASTM strength and permeability testing from wet grab sampling and verification coring, more and more testing methods are being employed and accepted. However, these other testing methods tend to be unnecessary, lack consistency and repeatability, and are more subjective to manipulation and interpretation. In certain projects, there are also misconceptions involved with the results of wet grab sampling and verification coring, hence it is important to note how these wet grab sampling and verification coring work and represent the work in terms of quality of production.TYPES OF PROJECTSCDSM projects include (but not limited to) in-situ stabilization, liquefaction mitigation, excavation support, groundwater cutoff, and pollution containment. Although these projects use similar equipment on the jobsites, each project is treated differently in terms of catering to specification, uses of different mix designs, and emphasis on certain steps during production.Different types of projects with different specification changes the focus of quality, but soil types in jobsite also determine how to proceed with production. For example, a jobsite with predominate gravel layer must be treated differently as opposed to jobsite with clayey sand as the main soil type.WET GRAB SAMPLEWet grab sampling is one of the most used testing methods for QA/QC. The wet grab sample specimen is retrieved right after finishing the production of the desired element.Wet grab sampling equipment consist the use of 28 cubic inch (458.84 cubic cm) box attached directly to one of the auger stems. Hinges attached to the top and bottom of the box is fabricated to allow collection only during auger withdrawal. The collection box is strapped just above the mixing paddles on the auger stem and measured from the center auger head tip to confirm proper depth of collection. This box method has been used in Japan and U.S. for numerous projects."

Jan 1, 2017

By P. V. Chandramohan

"The paper deals with the arrangement of structural members for a retaining structure used as a berth in the port of Krishnapatnam. The height of retention is 24.3m. A T-shaped diaphragm wall acts as the retaining surface. A relieving platform has been provided at the top to ease lateral earth pressure on the wall. The diaphragm wall is tied back to a combination of vertical and raker pile. Later, this arrangement was altered to replace the relieving platform with just lowering of ground level below the berth. The tie back was changed to a classical A-frame anchorage. At certain reaches, installation of piles pointing towards the rear was obstructed by a conveyor structure. The anchorage was then changed to include a vertical pile and a pile that points towards the front of the berth. Change in position of inclined pile alters the force in the pile from compression to tension.GeneralPort is a major link in the multimodal transport chain. Berth is the heart of the Port infrastructure. It is here the ocean freight changes to land transport. The change-over, warrants special type of heavy duty handling equipment. The equipment and the process necessitate deep seated foundations. On one side of the berth, deep drafted ships would be berthed. But adjacent to this heavy duty cranes would be operating at the deck level. Berths are of various types. Some are founded on piles and may project into water. Some operators prefer a retaining structure. At the port of Krishnapatnam, a retaining structure was preferred. Dredged level at the berth was to be -20. Deck of the berth was at +4.3. This meant that the height of retention of soil was 24.3m. Ports are generally located near the coast. Subsoil in the port area generally consists of cohesive material of low shearing strength. The berth has to cater to imposed vertical and horizontal loads.Structural functionFor bulk cargo and containers, berth has to support the two crane tracks. These tracks will carry heavy wheel loads of the crane. Besides, the space between the tracks would be used for stacking of cargo or hatch covers. In short, the deck will be subjected to heavy surcharge. This vertical load will manifest as additional lateral force on the retaining wall. Since the height of soil to be retained is high, it is a practice to relieve the lateral earth pressure due to the heavy surcharge of the wall. This is done by providing a relieving platform. The surcharge of superimposed load on the deck and the self-weight of the soil up to a few metres below would be relieved by a suitable platform. This vertical load would be transferred directly to deeper levels through piles. Mooring pull is a horizontal force exerted by the vessel on the bollards towards water side. Berthing force is exerted by the vessel during berthing, through fenders and acts towards land side.Diaphragm walls are usually employed as the retaining face. If the height of retention is less, these walls can cantilever out but in the case of large retention, they have to be tied back. The ties are to be anchored on to suitable arrangements like a dead-man or an A-frame. Berthing structure in the early stages at Krishnapatnam port is shown in fig 1."

Jan 1, 2015

By Chiranjib Sarkar, Sibapriya Mukherjee, N Kumar Pichumani

With the rapid expansion of urban transportation systems, tunnels and cut & cover structures are considered as the only solution in improving the urban space congestion problem in mass rapid transit system. Therefore, it is necessary to accurately design underground structures with realistic assumptions and considerations of design parameters like site geotechnical data, water table, surcharge load etc. Over conservative approach provides not only uneconomical design but sometimes it also causes overdesign of the concerned structures. Water table depth has a significant role in some design aspects of underground structures like floatation check, lateral and uplift pressure on the buried structure, etc. In current practice of tunnel and cut & cover structure design, water table is assumed to coincide with the ground level. Most of the Design Basis Reports & Outline Design Specifications directly mention consideration of water table at ground level for floatation check and load calculations, etc. However, the actual scenario is different in most of the cities specially in northern, central, western and eastern regions of India except the coastal cities. In the present study an attempt has been made to carry out a parametric study on the effect of water table depth in the design of a typical 6.3m outer diameter circular tunnel with 6m backfill. In this study, it is also attempted to establish an analytical method of calculating the most realistic consideration of water table depth instead of the present hypothetical assumption of considering water table to coincide with the ground level. The findings of the current study may be helpful to the researchers and practising engineers in design of tunnel and cut & cover structure for subways and metros.

Nov 1, 2022

By H. Shiri

Iran's largest natural gas field is South Pars, geologically an extension of Qatar's 900-Tcf North Field. South Pars was first identified in 1988 and originally appraised at 128 Tcf in the early 1990s. This Field contains 38.6 % of the gas resources of Iran and is regarded as the largest offshore gas field in the world. Offshore geotechnical site investigations are one of the key activities of upstream fields operators to supply the EPC contractors with the required results for designing approaches of offshore complexes. In the mean time a lot of marine site investigations have been carried into execution within the phases of South Pars development. The authors are currently trying to create the fundamentals of investigating the small- and large-scale spatial variability of the South Pars Gas Field in Persian Gulf/ IRAN. Part of this investigation is the providing of an extensive data base of the offshore geotechnical properties of South Pars. Such a data base, will enable a model to be developed of the large-scale variability of these properties. In addition, this data set will provide a data whereby general trends to be established, as well as, providing relationships between geotechnical parameters and spatial parameters utilizing probabilistic and data mining methods like ANN (Artificial Neural Network) in Geotechnical Engineering.

Jan 1, 2006

By George Burnhart

"Sonic drilling is a relatively new technology even though it has been in development since the late 1940s. It was initially funded by the U.S. petroleum industry and then, in the late 40s, Russian scientists worked on developing sonic drilling, their interest based on drilling rates 3 to 20 times that of conventional methods. In the early 1960s, the Shell Oil Company backed research that resulted in a down-hole device with a series of eccentric weights driven by drilling fluid to generate vibration. Hawker Sidley, in the early 1980s, developed the first modern prototype sonic drills in Vancouver B.C. and the North Star Drilling Company in Minnesota became the first contractor in the U.S. to operate sonic equipment in 1985. In 1994, North Star became a division of Boart Longyear, headquartered in Salt Lake City, Utah.What’s Unique about a Sonic DrillA sonic drill rig appears and operates very much like any conventional top-drive rotary rig. The key difference is that a sonic drill has a specially designed hydraulically powered drill head, containing oscillators, that generates adjustable high-frequency vibratory forces. The sonic head is attached directly to the drill pipe or outer casing, sending the high frequency vibrations down through the drill steel to the face of the drill bit. This creates displacement, fracturing or shearing action depending on the material being drilled. The oscillator uses two eccentric, counter-rotating balance weights or rollers that are timed to direct 100% of the vibration at 0 degrees and 180 degrees. An air spring houses the oscillators and separates the vibration from the drill rig itself. The vibratory frequency is controlled to suit operating conditions and to achieve optimum drilling rates.When the vibrations coincide with the natural resonant frequency of the steel drill rod or casing, a natural phenomenon called “resonance” occurs. It allows the rig to transfer timed vibratory energy into the top of the drill string, utilizing the natural stored energy of the steel. This causes the drill string to use inertia and act like a flywheel delivering tremendous amounts of energy directly to the bit face. In friendly overburden formations, a sonic drill rig can achieve penetration rates of one ft per second."

Jan 1, 2008

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Sara Anderson, Rachel Nicholls, Tim Chapman, Janice Windle

"In city center sites around the world, and in particular in London, foundation reuse is becoming increasingly widespread as the ground is filled with detritus from previous developments. This paper sets out a systematic framework to consider the need for and benefits of foundation reuse and key issues to be resolved for foundation reuse to be successfully adopted on redevelopment projects. Once foundation reuse has been identified as a potential foundation solution there are several key stages in the design and construction process where the decision to reuse foundations needs to be assessed. The paper concludes by emphasising the importance of ensuring that the foundations being installed now can more easily be reused in the future.INTRODUCTIONThe concept of re-using foundations is not new, and has been adopted on an isolated project-byproject basis for many years. However, over the past decade, interest in the potential of reusing existing piles and caissons within Europe has increased significantly, with a growing interest in the United States of America and Japan. The need has been driven by necessity: on many urban sites the space available for new foundations diminishes with each new set of piles, and these problems can only grow in the future.Initiatives such as the European Union's RuFUS (Re-use of Foundations for Urban Sites) research project have resulted in identification of the key issues for technical viability and risk that have previously hampered potential foundation reuse projects.There is a need to define a systematic approach to the reuse of foundations so that the risks associated with reuse can be identified, managed and mitigated. This requires improvements in knowledge to provide confidence in the long term behaviour of the foundation support and address the risks involved in reusing existing foundations to overcome perceived obstacles in making foundation reuse a realistic option for many sites."

Jan 1, 2005

By Mario Mauro

In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria. For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

Circular secant pile shafts were installed along the tunnel alignments for both the Ohio Canal Interceptor Tunnel project in Akron, Ohio and the Ohio River Tunnel project in Louisville, Kentucky. The diameters ranged from 34 to 51 feet and the depths ranged from 49 to 107 feet. Verticality and concrete volumes were measured on all piles to verify compliance with the design, which for some shafts consisted of a finite element model with multiple openings using unreinforced concrete secant piles. All secant piles were drilled into rock to seal off the groundwater. This paper will discuss the design, construction and quality control of the secant piles for these projects. INTRODUCTION Many Midwest and Northeast cities have Combined Sewer Overflow (CSO) systems which discharge pollutants into waterways during wet weather events. One way to remedy this issue is to provide a temporary overflow tunnel. A temporary overflow tunnel connects to the combined sewer system and collects the overflow during wet weather events, storing the wastewater until the event has subsided. After the storm event, the stored wastewater can be pumped to the treatment facilities and processed as normal. Project Background – Akron, OH The Ohio Canal Interceptor Tunnel (OCIT) project was performed as a result of the Environmental Protection Agency’s (EPA) Consent Decree with the City of Akron, Ohio. This Consent Decree required modification of the existing Combined Sewer Overflow system. The resulting project consisted of a 27- foot diameter tunnel with multiple points of entry to capture the sewer overflow and prevent it from entering waterways. The tunnel is over 6,000 feet long and is as deep as 150 feet below the ground surface; see Figure 1 below.

Jan 1, 2019

By Douglas R. Hardin, Stanley L. Worst, Joanna Mason

A challenging earth retention project presented itself in Washington, DC in the backyard of the historic House of the Temple (The Scottish Rite of Freemasonry, Supreme Council 33°). Located at 15th St NW and S St NW, a forty-foot-deep underground basement was to be installed adjacent to the existing Temple, a historic Carriage House structure dating back to the 1800’s and across a narrow alley from a four-story brick apartment building. The unique geology of the site included typical urban fill overlying a mixture of loose alluvial soils underlaid by dense marine deposits of the Potomac Formation. The clay, sand and gravel of the Potomac included nested boulders up to three feet in diameter. Design of the earth retention system accounted for ground conditions, installation methods and estimated movement of the system and adjacent structures. Anticipated ground water and unanticipated water from leaky sewers also proved obstacles to overcome during construction. Soldier beams were installed using a variable momentvibratory hammer to minimize disturbance to the historic and sensitive structures. Monitoring of the existing structures included both seismograph and optical targets during installation of soldier beams and as the excavation progressed. Micropiles drilled into the Potomac Formation were a part of the permanent foundation for the new structure. This local case history will delve into the details of the successful design, installation, and performance of an earth retention system and micropiles in a historic and highly congested urban environment.

Oct 1, 2022

By Gene Bryant, Wesley Schmutzler, Matteo Bertoni

The levees where the Mississippi River and the Lower Wood River meet near East Alton Illinois have been a problem area for years due to underseepage. The first phase of the deep cutoff wall was a 2,000-linear foot section that was completed in 2016 for the Illinois Flood Prevention District Council. This section was installed along the Wood River and the Mississippi river to depths of over 135’, The United States Army Corps of Engineers was tasked with continuing the cutoff wall along the Mississippi river. The wall was a continuation of phase I with depths up to 140’. The 1,000’ long cutoff wall was installed through fill, loose sands, cobbles, and sandy clay. The cutoff wall was terminated in either Glacial Till or sound rock. In order to provide wall permeability equal to or less than 1.0 X 10-6 cm/sec a self-hardening slurry (SHS) composed of ordinary Portland cement, slag cement, and water was utilized. The depths reached on this project using SHS is the deepest done to date in the United States. Along with the permeability requirements, a very narrow range for the unconfined compressive strength was specified at 50 – 180 PSI. In order to monitor the ground movement and water level fluctuations during the excavation of the panels with the Hydromill or Clamshell, 6 automated inclinometers were installed and monitored continuously during panel excavation in phase 1. Seven automated piezometers were monitored in phase 2. This paper will give an overview of the project with emphasis on the effect of the excavation on the instrumentation, specifically the reaction of the piezometers as the last panels were installed. INTRODUCTION The project is in Illinois, about 1000 feet downstream from where the Wood River Creek enters the Mississippi River between East Alton, IL and Wood River, IL adjacent to State Highway 143 (Fig. 1). The Wood River Lower Cutoff Wall Phase 2 Project (WR2) was awarded to TREVIICOS SOUTH (TIS) in September 2017. The Main Project features are: Construction of work platform, inclinometers installation and removal, cutoff wall construction by the Self-Hardening Slurry method (approx. 135,000 sf) up to 140' depth, clay cap installation, and site restoration. The levee system along this stretch of the Mississippi River has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed to ensure that Levee failure would not be an issue in the future.

Jan 1, 2019

By Walter E. Vanderpool

Type 1B micropiles (Bruce and Juran, 1997) can be installed rapidly and efficiently. During an 85-day period, 536 micropiles were installed to depths of 61 meters within a site 41 meters by 43 meters. Their performance, as measured by load test, varied even where the materials, construction procedure, and installation technique were closely monitored and controlled. The variation in displacement, as measured by the standard deviation, exceeded 50 percent of the mean test-load displacement for all loads up to the maximum load applied (2670 kN). This study provides a statistical basis to predict variability with respect to the construction method, micropile materials, and installation technique. The variability of displacement at all test loads is a fundamental characteristic of this type of drilled deep foundation system.

Jan 1, 2002