Search Documents

By F. McIntosh Galbraith

EMPLOYING geophysics to find ore was for a long time considered by the Canadian mining fraternity to be a performance of dubious value: in a category somewhere between the practice of sorcery, and using a divining rod to locate underground water. With increasing knowledge, however, and with constantly improving instruments, a solid speaking acquaintance with this adolescent science is becoming an integral part of the mining geologist's stock in trade. And quite properly so: for, in the established mining districts, the ore deposits which could be easily found, by ordinary prospecting methods, have already been located. There remain; however, in almost all of the principal mining camps, areas which are covered to varying depths by glacial debris; and it is here that the obvious opportunities exist for the successful application of geophysical methods. Geophysical results must always be considered in the closest possible relation to the local geology; and, in reality, the 'doodle-bugs' are simply additional tools for the geologist (in the same category with a plane table or a microscope). The Sudbury Basin is a shining example of precisely this state of affairs. Detailed geological mapping has not significantly altered the position of the outer norite contact as placed on Dr. Coleman's original map of the district. What detailed examination has done, of course, has been to reveal the accuracy with which the contact can be placed in different parts of the district, and to show up, in consequence, areas in which further work might reasonably be expected to disclose hitherto unknown or unsuspected ore. Viewed in this light, the proportion of the norite contact which is covered by substantial quantities of overburden is astonishingly large.

Jan 1, 1939

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By G. C. Bateman

THE cause of silicosis and its prevention have held the attention of medical men and mine operators for many years and at the present rime the study of this disease is more than ever to the fore, even though a considerable abatement in the incidence of silicosis has been noted of late. This abatement is due to individual and collective efforts. The Industry is keenly alive to the situation and much research is being carried on. Silica dust is assumed to be a contributing factor in the cause of silicosis. How it acts progressively in the early silicoric is nor fully understood. As the study advances, more effective measures of control may be evolved. At present the Industry has three known methods of reducing the incidence: 1. By thorough X-ray examination of all applicants, with special reference to chest conditions. Those who are considered to be susceptible to the disease are prevented from entering the industry. 2. Thorough ventilation of the mine. 3. Control of tuberculosis in mining centres and removal of miners when first symptoms of tuberculosis become apparent. In 1934, the Ontario Mining Association formed a Committee, known as the Technical Silicosis Research Committee, to study and supervise work on problems related to silicosis. This Committee obtained the full-rime services of a mining engineer to carry our research work at the mines in the Province of Ontario. The Ontario Mining Association has also provided funds for the purpose of carrying on research work along pathological and biological lines. This work is being done in the Department of Medical Research of the University of Toronto, in the Banting Institute, under the supervision of Sir Frederick Banting. The Silicosis Committee work in full cooperation with the doctors in the Banting Institute and provide material from the mines for the it use.

Jan 1, 1936

By D. J. MacKinnon

Zinc metal was first produced in India around 1100 A.O. and a zinc industry based on retorting gradually developed in both India and China(1) . The vertical retort method for smelting zinc ores was developed in England in the 1730s; this was followed by the more fuel efficient horizontal retort process developed by the Belgians in the 19th century(2) . The horizontal retort process was the standard method of zinc manufacture until the 1950s when it became obvious that it could not compete with electrolytic zinc technology(2). The present day extractive metallurgy of zinc is dominated by the electrolytic process which now accounts for almost 80% of the world's primary zinc production. In recent years the electrolytic zinc process has seen significant improvements: the fluid-bed roasting of zinc concentrates, improved leaching and residue treatment techniques such as the jarosite and goethite processes, improved solution purification procedures, mechanization of the zinc electrolysis step and of the zinc melting and casting operation. In addition, new leaching processes have been implemented for the treatment of oxidized ores, particularly silicates, and the pressure leaching of zinc sulphide concentrates is now a commercial reality. Although the electrolytic zinc process was first used on a commercial scale in 1916, its history can be traced back to the 1860s. The purpose of the present paper is to outline the early history of the electrolytic zinc process and to trace the significant developments which led to the first successful commercial electrolytic zinc plants.

Jan 1, 1999

By R. Bruce Graham

"For the purpose of this paper, the Chibougamau area is taken as lying between lats. 49°20’ and 50°10’ N;-longs. 73°45’ and 75°30’ W. It comprises an area of some 4,000 square miles and is centred 300 miles north of Montreal.The first recorded report of metal deposits in Chibougamau was that of James Richardson in 1870-71 (I). In 1903 discoveries of asbestos, copper, iron, and gold made by Peter McKenzie stimulated considerable activity in the district. By 1909 interest had become so marked that considerable pressure was brought to bear on the Quebec Government to build a rail-way into the region. It was finally decided to have an authoritative opinion on its economic possibilities, and the Chibougamau Commission was appointed for this purpose (2). They examined the district in 1910 and concluded that at that time a railway was not warranted. Nevertheless, the district continued to be prospected and from time to· time gold and copper discoveries were made. Thus the Merrill Island deposit was discovered in 1920, the Campbell Chibougamau Cedar Bay deposit in 1922, Obalski in 1928, Opemiska Copper in 1929, and Norbeau in 1930.Difficulty of transportation was a severe detriment to the development of the region. Consequently the Quebec Department of Mines completed a road into Chibougamau in 1949. Further activity was encouraged. The Chibougamau Explorers, Quebec Chibougamau Goldfields, and Kayrand deposits were found in 1950. ** The copper-siderite zones on Copper Cliff ground were found in 1952 and 1953. Opemiska Copper, Campbell Chibougamau Mines, and Chibougamau Explorers were encouraged to prepare for production following favourable exploration results."

Jan 1, 1949

By John Crusius

? 3-year research program overview ? initial results- MainZone pit Waterline pit ? questions raised ? increasingly common in western N. America ? frequently low-pH waters with elevated concentrations of many metals ? water quality controls poorly understood ? some in U.S. are Superfund sites

May 1, 2002

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978

By F. R. Archibald

IN a recent paper on Roasting of Beattie Concentrate (1), the importance of controlling the temperature, and the sulphur dioxide concentration was pointed out. It is the purpose of the present paper to present further information by which the most satisfactory conditions for roasting are more specifically defined. Incidentally, a method of illustration is developed for representing roasting curves on a three-dimensional diagram. The primary purpose of this investigation, as in the case of the earlier work, was the search for information that would be of practical value in improving plant operation and gold recovery. For this reason, emphasis is laid on the regulation of essential variables and on definition of their optimum values and limits for maximum gold recovery in the subsequent cyanidation process. Good roasting is considered at least as much an art as it is a science, and, in this light, theoretical consideration of the nature and sequence of the chemical reactions involved is of secondary importance. The presentation which follows includes a series of graphical illustrations, an interpretation of the graphs, some theoretical considerations, and a description of laboratory technique.

Jan 1, 1940

By R. D. Livingstone

"THE LETHBRIDGE COAL FIELD lies mainly .to the north and west of the city of Lethbridge. Mining carried on in this area for over eighty years until 1965. Before the building of a railway the coal was carried by bullock wagon to Montana for use in smelting, and for a while by river boat to Medicine Hat for railway use. The single, almost flat, worked seam is designated the ""Galt"" seam and is about 1.5 metres thick. It belongs to the Belly River formation and is under cover of 80 to 180 metres of weakly stratified sediments. A complex system of cross faults adds to the mining difficulties. Close timbering required in the entries and rooms reflected in a high timber cost and lower output per man shift. The coal is High Volatile"" C"" bituminous in rank with maximum gross calorific value of 11,200 Btu per pound and with a well defined cleavage. Roof conditions in the field range from very tender and very heavy on the south end of the field and west of the Oldman River to a more stable character to the north. Relatively speaking, the whole field would earn a rather tender rating and definitely so in relation to many U.S. fields. Floor conditions are characterized by a bentonitic type heaving in the south end of the field west of the Oldman river to a more stable situation in the north, which can tolerate shuttle car operation if kept drained. Water problems are minimal, except paralleling the Oldman River, where the seam dips below the river level. While vigilance is necessary to prevent accumulations of gas, the volume is rather limited. The seam was entered by shafts, except where small mines were located along the Oldman river banks and gained access by drifts. The coal seam was developed by driving either 3 or 4 Face entries 2 1/2 metres (8 ft) wide on 18-metre ( 60-ft) centres. Sets of dual butt entries driven at right angles to the Face entries completed development work. Normally rooms up to 8 metres wide were turned off the butt entries on up to 11 - metre centres. These were worked in groups of three to five, depending on the roof conditions, and normally advanced 60 m (200 ft). In some areas rooms had to be abandoned short of their objectives due to roof pressure, heaving floor and intermittent work."

Jan 1, 1985

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By Wencheng Gao

An attractive way to beneficiate magnesium chloride and aluminum chloride is to prepare Mg-Al spinel, an excellent refractory material. Mg4Al2(OH)14?3H2O, the precursor of spinel, can be prepared using a co-precipitate method from aqueous MgCl2-AlCl3 solutions. The co-precipitation process of magnesium-aluminum from acidified chloride solutions by using NaOH or NH4OH as base neutralization agent was studied. Co-precipitation was conducted from different mixed solutions ? at initial CAl=0.0625M and Mg/Al molar ratio from 0.5 to 10, the temperature range from 30 to 90 °C. The effect of other parameters, including base type, method of base addition, base addition rate, aging time, background electrolyte and concentration were also investigated. The co-precipitation process was monitored by potentionmetric(pH) measurements. The experimental pH curves were characterized by two platforms separated by a steep jump in pH at Mg/Al molar ratio 0.5~6. The first platform was centered at about a pH of 3.8 and the pH of second platform was varied with different conditions. When the Mg/Al molar ratio was up to 6~10, the first platform in pH was almost disappeared. Furthermore, the shapes of pH curves were also affected by base type, base addition rate and method of base addition. Experimental results showed that the first platform in pH was connected with Al precipitation, and the second platform was involved with Mg. The final co-precipitates were characterized by XRD, TGA-DTA, particle size analysis, SEM and TEM. We found both Mg/Al molar ratio and temperature proved to be the key parameters controlling the formation of Mg4Al2(OH)14?3H2O phase. At solution Mg/Al ratio=0.5~4, the main precipitate phase was Bayerite (Al(OH)3) admixed with Mg4Al2(OH)14?3H2O; at Mg/Al ratio=4~6, the main phase was Mg4Al2(OH)14?3H2O admixed with some Mg(OH)2; while from Mg/Al ratio=6~10, the systems were mixtures of Mg(OH)2 and Mg4Al2(OH)14?3H2O.

Oct 1, 2011

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019

By John R. Morgan, Peter Graham

"Onakawana Development Ltd. and Mana/ta Coal Ltd. have completed feasibility studies on a large lignite deposit located in the James Bay lowlands of northeastern Ontario. The mining plan described in this paper would supply coal for approximately a 33-year period with peak production in the early years of approximately 6.5 million tonnes per year then declining to 1.2 million tonnes in year 33. This paper describes the geology, resources, lignite quality, mine planning and related topics. LocationThe Onakawana lignite deposit is located in northeastern Ontario in the James Bay lowlands (Fig. l). The Ontario Northland Railway crosses the property and links it to Moosonee, JOO km further north, and Cochrane 180 km south. The area is crossed by latitude 50° 37', the approximate latitude of Calgary. Toronto lies 800 km south of the study area. History of Development The deposit has been known since the late 1600s when early English settlers extracted limited amounts of lignite for use at Moose Factory. The deposit has undergone sporadic periods of exploration activity in the late 1920s and early 1930s when the Ontario government drilled 116 holes, sunk two exploration shafts and published several technical and economic studies. Interest in the property was reactivated from 1939 to 1945 when the Timiskaming and Northern Ontario Railway Ltd. drilled 182 additional closely spaced holes, excavated a test pit adjacent to the rail line and installed a boiler for testing purposes. In 1965, Alberta Coal Ltd., the predecessor of Manalta Coal Ltd., first became involved. Since then a further 182 holes have been drilled and coied, and the existing test pit reopened for sampling. In 1980, various reassessment studies were launched, including geology, mine engineering, conceptual design and environmental assessment studies. The following discussions have been drawn extensively from these reports."

Jan 1, 1985

By J. W. Reynolds

This paper describes the function of the research and development department of a large mining organization and the benefits which can be derived over the years. Examples are given of work done in rock drilling, ventilation, noise control and the development of backfill stowing machinery.

Jan 1, 1970

By L. Wolofsky

"The Candego property is in Boisbuisson and Christie Townships, Quebec, about 13 miles south of Marsoui, a village on the north coast of the Gaspe peninsula, 80 miles east of the railhead at Matane. It was the first producing mine in the peninsula. Production to October 1954, when operations were suspended, totalled 68,497 tons of ore, which yielded concentrates containing 8,706,535 lb. lead, 5,870,272 lb. zinc, 355,526 oz. silver, and about 1,000 oz. gold. The property was acquired by the present company in the summer of 1955.The mine has been developed by seven adits, driven into the west slope of the valley of the Marsoui River. The river here is at an elevation of about 1,600 feet, and is roughly 1,500 feet below the level of the adjacent upland. Adit elevations range from 1,760 to 2,330 feet. Five of them are in one vertical zone, on what was originally believed to be a single vein. Past production has come from Nos. l to 5; the chief present high-grade ore reserves are in No. 7.The author's observations were made in adits Nos. 3 to 6, in several of the old pits, in the surface trenches, and on drill core, at various times between December 1952 and September 1953. Much of the surrounding area has been mapped by Jones (I) and McGerrigle (2) for the Quebec Department of Mines. H. M. Kingsbury served as consulting geologist to the mining company for several years.General GeologyThe Candego veins occur in Lower ( ?) Ordovician sedimentary rocks which form a strip about 15 miles wide along the north coast of the Gaspé peninsula. The series includes limestones, shales, and sandstones, mildly metamorphosed in places. Three miles south of the mine is the north contact of the granitic intrusive, regarded as Lower or Middle Devonian, which underlies the Tabletop Mountains area. This batholith is about 10 miles long, in a north-south direction, and about 4 miles wide. At Mount Albert, about 5 miles west of the Tabletop intrusion, is a group of basic rocks, amphibolites and serpentinized peridotites, thought to have been intruded at the close of the Ordovician."

Jan 1, 1949

By J. W. McCammon

CRANGES in construction ideas and the continually rising costs of labour and conventional building materials, particularly since World War II, have prompted widespread investigations into the development and adaptation of new materials to meet the new requirements and to help reduce costs. Lightweight aggregates have been prominent in these investigations. The lightweight aggregates most commonly used today are foamed slag, cinders, pumice, diatomite, exfoliated vermiculite, expanded perlite, and bloated clay or shah. Lightweight aggregates contribute to the building industry in several ways: ( 1) in large structures the reduction in deadweight effected by the use of lightweight materials reduces the amount of reinforcing and structural steel necessary to support the structure; ( 2) the decrease in weight of lightweight blocks makes handling easier and faster; (3) pre-fabricated floor and roof slabs and tilt-up walls of lightweight concrete have become feasible and popular; ( 4) lightweight aggregate concrete has good nailability and is easily channelled; (5) concrete and plaster made with lightweight aggregate have good heat and sound insulation properties.

Jan 1, 1957

By J. F. Harkom

Introduction The importance of the preservative treatment of mine timbers need scarcely be stressed here. Increasing the life of mine timbers will reduce one of the major costs of mining and also conserve the available timber supply which lies within easy access of the mines. When treated, several species of timber may be used which otherwise could not be considered, owing to their short life. Another feature which should appeal to the mining industry is that wood preservatives are a mine product, and the benefit to be derived from the increased consumption of wood preservatives due to the example set by mine owners is not inconsiderable. Mine timbers may be divided into three classes when considering preservative treatments. (1) Timber obviously not profitable to treat owing to long natural life or short period of time in service. (2) Timber that obviously should receive protection from decay. (3) Timber installed in locations where the length of service required will depend on future developments, so that preservative treatments might or might not prove to be a profitable investment.

Jan 1, 1930

By Chris G. Dobson

Introduction The Britannia mine is at Britannia Beach, on Howe sound, approximately thirty miles from Vancouver. The first claims were staked in 1898, and a local company was formed at that time to develop them. In 1904, Mr. Grant B. Schley became actively interested in the property and in the following year the Britannia Mining and Smelting Company, Limited, was incorporated to operate it. This Company was taken over a few years later by the Howe Sound Company, Limited. The mine comprises five more or less separate ore-bodies, which have produced approximately 20,000,000 tons of ore to date. The East Bluff ore-body, with which the present paper deals, is well suited to large-scale mining by means of carefully placed powder blasts. It covers approximately an acre and lies in the slate footwall, in a bay produced by a fault. The hanging-wall side, on the west, forms the face of the Bluff glory-hole, which extends to the 1,200 level. A portion of this ore was available for breaking into this old glory-hole, below which four bulldoze chambers could quickly be built. Mining of this block is complicated by a very soft footwall, which 'runs' badly when broken. In stoping, care is taken to guard against the hazard of dilution by deliberately leaving a small portion of ore on the footwall. Some of this will undoubtedly be lost, but it is hoped to recover a fair amount of it after the major drawing is completed. The deposit occurs in a greenstone which has been highly silicified following brecciation. The chief minerals are chalcopyrite, sphalerite, and pyrite. Concentrates of copper, zinc, and pyrite are made at the mill. The average grade of ore runs 0.7 per cent copper, 1.5 per cent zinc, and 0.03 oz. gold per ton. The rock, which is practically a chert, is extremely hard, but shatters well. Both in stoping and drifting, holes must be closely spaced and powder used generously. Development When development work started in the East Bluff, there were no raises and only one drift on each level in this section of the mine. After blocking out the ore by thorough diamond drilling, a production of two thousand tons per day was set as a goal. To obtain this tonnage from so small an area required a great deal of carefully planned and well timed development work.

Jan 1, 1935

By J. F. Wright

Introduction Previous to 1924 the mining fields of Manitoba and adjoining territory had not been prospected in detail, and the reports of the exploration of the mineral discoveries to that date had been discouraging. As a result of the apparent failure of all the mining operations, some considered that geological conditions in the country westward from lake Superior extending across western Ontario, eastern and northern Manitoba, and northern Saskatchewan, were different from those in the northeastern part of Ontario, where large gold mines had been developed. Discoveries of importance thus were necessary to renew interest in the mining possibilities of this part of the Canadian Shield, and the successful operations at Flin Flon and Howey in large part were responsible for the beginning of the present activity in what may be described as the part of the pre-Cambrian Shield within central Canada. In Manitoba, the more important developments at present are in the Central Manitoba, Gods Lake, and Knee Lake fields. The large area from west of Flin Flon east to Herb Lake, also, is being explored carefully for gold deposits of merit. A number of properties in Red Lake, Woman Lake, and Pickle Crow areas are being drilled and explored underground. Many of the mines of the Lake of the Woods area, that were producing gold 30 years ago, are re-opened, and new prospects in this field and in the country to the east are being explored. The recent development of Little Long Lac mine in an area near the railway, and considered by some to have been thoroughly prospected years ago, has stimulated interest in the areas formerly prospected. In the autumn of 1934, the belts of greenstone and sediments in the country east of lake Nipigon were staked, and deposits in these fields will be explored in detail this year. This paper is presented to discuss the general features of the geology and gold deposits of the various prospecting fields in Manitoba and adjoining territory. Details of a number of the areas and mines will be presented at this meeting in papers by Barton on Little Long Lac, Tanton on Sturgeon River, Baker on Gods Lake, and Brownell and Kinkel on Flin Flon. Although mining was not active in most of this territory previous to 1930, geologists of the various government departments continued field studies and interesting reports were issued.

Jan 1, 1935

By Robert D. Irvine

"Enhanced concern for protection of the environment and attendant actions by environ-mental regulatory authorities in support of this concern are influencing, to varying degrees, the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms.In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, to outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States."

Jan 1, 1996