Search Documents

By P. H. Shipway, D. G. McCartney, H. Saghafifar

The microstructural changes during thermal ageing at 650ºC in the interfacial region of Alloy 625 weld overlay on a 2.25Cr-1Mo steel was evaluated. Optical microscopy, scanning electron microscopy in SE and BSE modes, electron probe microanalysis and hardness mapping were used to characterize as-welded microstructure and its changes during thermal ageing and precipitates of interfacial region. Carbon migration across the interface was recognised as a major issue. A region of 300 µm wide adjacent to the fusion line, which was found harder in the as-welded condition decarburized during thermal exposure. Studies revealed that this region transformed to a soft region containing large ferrite grains and micron-sized carbides. In the weld overlay, a 50 µm wide hard band (over 650 Kgf mm-2) adjacent to the fusion line formed and carbide precipitates were observed along grain boundaries. Carbide precipitation mostly occured in the 150 µm wide region close to fusion line.

Jan 1, 2017

By S. J. van Rensburg

Competition for resources, including water and arable land, refocused attention on water and gold tailings management with respect to quantity and quality. MINTEK established and validated an "Advanced Leach Facility" to record kinetic leach information aimed at gold refractory sulphide ores. This facility was developed because of the need for additional leach process information to enable proactive decision making. Instead of focussing on optimised gold recovery only, the impacts of pre-oxidation methodologies were evaluated by considering key parameters, including cyanide speciation, reagent consumption, thiocyanate, arsenic, heavy metals, salt loads, water quality and residue stability. Results from oxidative leaching of a refractory gold ore employing oxygen, ozone, ultra-fine grinding, high shear and pressure oxidation are discussed. The relative cyanide and lime costs and environmental and sustainability effects associated with these technologies are briefly outlined.

Jan 1, 2011

By C. A. Pickles

Nickeliferous limonitic laterite ores contain considerable free moisture. In this research, the application of microwave radiation for the drying of this ore was investigated. The effects of sample mass, initial moisture content and porosity on the microwave drying rate were studied and the results were compared to those obtained with conventional drying. Microwave drying rates of two to three times the conventional values were achieved. Further enhancement of the microwave drying rate was realized by increasing the flow rate of air over the sample or by operating at reduced pressure. The high microwave drying rates were attributed to the inverted temperature gradient which resulted in internal heating and boiling and this in turn promoted movement of the water, both as liquid and vapour, to the surface.

Jan 1, 2005

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By K. Torigoe, S. Owad, C. Tokoro, Y Tsunazawa

The mechanism of an abrasion process to recover metal values by removing components from printed circuit boards (PCBs) is modeled using a discrete element method (DEM) simulation. To simulate the abrasion process, a model PCB geometry was constructed consisting of bonded particulates. The simulation allowed connections between particles to be broken if the bonding force calculated from DEM exceeded a threshold level. Simulation results were compared with experimental comminution data using an agitation mill with test PCBs on which nine capacitors were surface solder-mounted. Simulation results obtained from the DEM with the anchoring model corresponded to experimental observations.

Jan 1, 2011

By J. M. Cormie

"The orebodies of the East Malarcic mine are interesting from a geological standpoint because of the very small amount of vein quartz, the occurrence of much of the ore in soft greenstone schist, the presence of innumerable bodies of porphyry and diorite, and their obvious relationship to structural features .The property lies in the northeast part of Fourniere township in western Quebec, and within the important fault zone that geological mapping in recent years has shown is traceable wesrward through the Noranda and Kirkland Lake camps and eastward to beyond the Val d'Or region . The claims included in the property were staked by J.P. Norrie and L. K. Coffin in 1932, but gold was not discovered until i934. Production began late in 1938. The total amount of ore milled up to the end of 1945 was 2,837,091 tons from which gold having the value of $16,631,758 was recovered.The region is underlain by an alternating series of Early Precambrian sediments and volcanics cut by innumerable intrusives. These are more fully described in the works of Gunning, Ambrose, and Norman. The East Malanie property is underlain by three formations, which, named from north· to south, are : the Cadillac sediments, the Blake River volcanics, and the Kewagama sediments. In addition, there are countless intrusions of porphyry and diorite, particularly in the greenstone, occurring in all sizes up to those measurable in hundreds and even thousands of feet . These constitute a large proportion of the greenstone in places. In many parts of the ore zone there is more porphyry and diorite than schist. The greenstone itself is not homogeneous but includes peridotite, andesitic lava, and soft talcose schist.Orebodies have been found in both the Blake River volcanics and the Kewagama sediments. They are not known to occur in the Cadillac group. The ore occurs in a zone of pyrite mineralization in which almost no other metallic minerals and very little vein quartz are present. Generally, the grade varies directly with the amount of pyrite. The mineralization is later than all the rocks of the area. Diorite was a particularly favourable rock for mineralization and contains the highest grade of ore, but any rock in the fault zone may be ore-bearing, whereas the same type away from the zone is not."

Jan 1, 1954

By B. D. Frater

Geometallurgy or process mineralogy is an integrated part of the scoping, pre-feasibility and feasibility phases of a project as well as an existing operation. A well planned and executed geometallurgical testwork programme during the early phases, will result in a more accurate decision making process during the selection phase. The better this integration between geological, mining and metallurgical data gathering during the early phases, the more accurate the predictions will be with regards to throughput and recovery during modelling and process and equipment selection in later phases. This will enhance and improve the mine and process scheduling and subsequent NPV. Geometallurgical information gathered during plant operation and testwork can for example be used to statistically model the pit optimisation, plant throughput and optimise the plant for certain feed material (characterised by statistical models).

Jan 1, 2017

By F. A. Charalambous

Brannerite is commonly referred to as a refractory uranium mineral as it is usually highly resistant to acid leaching. There is however widely varying literature data on brannerite leaching, with some studies reporting that brannerite leaching can be achieved under relatively mild conditions. The differences observed for brannerite leaching are most likely due to the high degree of variation in the composition and structure observed in natural brannerites. These aspects of brannerite chemistry however are not very well understood due to a lack of fundamental research. The aims of this study were to investigate and develop methods for synthesising brannerites of varying composition and to investigate the effects of composition on brannerite leaching in acidic conditions.

Aug 1, 2010

By A. L. Rutledge, R. S. Nichols

"Waste dump development at the Fording River Operation s in British Columbia began in 1971. In 1981, several unique as well as unplanned situations provided an opportunity to study water flows through waste dumps.The key to the drainage is naturally segregated rock sizes .created by end dumping from the crest of a pile. The largest size material accumulates at the toe. Flow rates along the base of the studied dumps varied from 2,800 to 13,500 m3/day or 0.032 to 0. 156 m3/s (1.2-5.5 cfs}. Sediment concentrations in the water ranged from 1 to 1,800 mg/I.This paper describes water flows through dumps of varied lithology and maturity. The results suggest that neither long-term water flow nor contained sediments in small streams are jeopardized when crossed by end-dumped fills.IntroductionThe Fording River Operations are located in southeastern British Columbia approximately 115 km north of the United State s and 10 km west of Alberta, within the medial range of the Rocky Mountains. All production is carried out at elevations ranging between 1,600 and 2,200 m above sea level.The property is within a continental climatic zone, with temperature extremes of - 40°C in January to +35°C in July. The average annual precipitation of 335 mm of rainfall and 390 cm of snowfall feeds the numerous seasonal, small drainage courses along the Fording River valley.Since start-up in 1971, 149 million bank cubic met res of waste from truck-shovel and dragline mining have been placed in numerous dumps or ""spoils"". The dumps were developed to the point that several unique situations could be studied. During the peak run-off period of May-June 1981, water flow studies were performed on dumps of varied lithology and maturity. This paper describes the results of the study."

Jan 1, 1982

By M. E. Grimes

"The future of the uranium industry in Canada during the next twenty years will be very dependent on political and social issues on a world scale. Technology, as such, will tend to be of lesser importance. Nonetheless, some technical changes can be anticipated.This paper deals with milling of uranium ore, leaving further processing and nuclear power production to specialists in these fields. An attempt has been made to look at uranium production technology in Canada in relation to that in other countries, and to draw interference regarding future changes that seem probable in the Canadian context. In particular, recent advances in mill equipment are considered.The chemistry of uranium and its relatively low concentration in most ores has been responsible for a completely hydrometallurgical approach to mill processing, and this should continue. In spite of little commercial success to date, pre-concentration of lower grade ores will be researched further in order that these ores can compete with higher grade deposits in Canada.The discovery of the relatively high-grade ores of the Athabasksa region will undoubtedly influence choice of mill processes and equipment. The potential effect on innovations is discussed"

Jan 1, 1986

By D. Ibarra, J. Jacob, A. G. Guezennec, P. d’Hugues, A. Archane

The lack of adequate gas mass transfer is a rate limiting step in many bacterial leaching processes. Oxygen often becomes a limiting factor because of its low solubility compared to the high demand induced by sulfide oxidation. One way of increasing the solubility of oxygen in water or in media solution is by increasing the driving force, i.e. raising the oxygen partial pressure in the gas stream supplied to the leach pulp. The use of oxygen is a well-known practice in high-temperature bioleaching reactors (above 70°C) whereas air is usually preferred in medium and low-temperature operations in order to avoid too high dissolved oxygen concentrations which could impact negatively the bacterial activity. The purpose of this study was to investigate the use of oxygen-enriched gas in bioleaching reactors at 40°C in order to improve the gas transfer in the system when operating at high solid load (20% and more). Bioleaching experiments were performed on a sulfide-rich tailing waste (pyrite 60%, copper 0.8%, cobalt 0.06 %, gold 1 g/t) using the “BRGM-KCC” bacterial consortia. The reactor used for the tests was designed on the basis of a new bioleaching reactor concept developed by Air Liquide, Milton Roy Mixing and the BRGM which uses floating agitators to inject gases and to mix and to suspend solids in the bioleaching solution. Two types of tests were carried out: with air injection and with oxygen enriched gas mix injection. The aim of this work was to confirm the capacity of bacteria to grow and to dissolve pyrite in this type of bioreactors in oxygenrich atmosphere, and to compare sulfides dissolution rates during both types of bioleaching tests. The results obtained show that the use of oxygen enriched gas mix does not decrease bioleaching performances compared to air injection. High metal extraction yields were achieved (above 80%). No deleterious effect due to oxygen use was observed on the bacteria despite the high level of dissolved oxygen reached in oxygen tests (up to 14 mg.L-1).

Jan 1, 2016

By G. Vibert Douglas

It has long been recognized that there are considerable difficulties connected with the physical and chemical explanation of shoots of ore. The literature of Mining Geology has frequent references to this subject; but the reasons given for the actual location of primary ore-shoots have been very tentative. In practice, the geologist or miner depends to a great extent on sampling and assaying to determine the boundaries of profitable ore within the mineralized zone. An ore-shoot is a portion of a mineralized zone which has a sufficient concentration of valuable minerals to make it ore. Ore deposits have been classified according to many schemes. There are classifications based on morphology and on genesis. However, it is also possible to classify hypo-gene hydrothermal ore-bodies in terms of ore-shoots or vice versa. A.-Ore-deposits in which the whole of the mineralized zone is ore, which is the same as saying that the ore-shoot extends throughout the mineralized zone. An example of this type of deposit would be the pyritic mineralization of Rio Tinto. B.-The second type would comprise those deposits in which the ore-shoots bear some relation to the geological structure of the area: all deposits in which 'bonanzas' occur in folds in the zone, at the intersection of veins along certain fault (or joint) features and other such controls. There are a great many examples of this type: (a) The Rhodesian copper lodes, where Bancroft and Gray have pointed out the association of the shoots of ore with drag folds. (b) A similar association has been pointed out by Faribault for some of the gold veins of Nova Scotia, e.g., Mount Uniacke. (c) The great bonanza of the Comstock lode in Nevada. C.-Deposits in which the localization of ore has been effected by the chemical character of the wall-rock. Examples of this type are the Fahlbands of Scandinavia, and the 'indicator' deposits of Ballarat, Australia. D.-Lastly, deposits in which there is apparently no structural and no chemical control.

Jan 1, 1934

By C. Cano

One of the main concerns within the mining industry is to minimize the impact of tailing facilities to the environment and nearby communities. Since the implementation of the first thickened tailings disposal (TTD) methodology at Kidd Creek in 1964, the thickened tailing disposal has been growing alternative disposal technology to mitigate the environmental impacts. Technical investigations on the TTD technology have been studied in detail to counteract the increasing shortage of water resources. One of the benefits observed with TTD is its resistance to potential earthquakes, particularly in zones with high seismic activity (Los Andes). TTD technology optimizes the maximum possible density for the material and generates a negative internal pore pressure in the material due to the surface and sub-surface water evaporation. This internal pore pressure should be enough to resist the pores pressure to which tailings are subject due to an earthquake action. The objective of this study is to verify the Shrinking Limit (SL) of thickened tailings during initial deposition and in the long term and the ability of tailings deposited by TTD would resist liquefaction. Fresh tailings coming from a flotation process of a copper plant concentrator were used. The samples put under cyclical three-dimensional tests associated with maximum credible earthquake magnitude range of 7.0 8.0 to develop a curve for the safety factor v/s depth for dry densities related to the maximum density obtained at the SL. At a dry density of 1.65 t/m3 liquefaction did not occur at any depth. At 90 % of dry density of 1.51 t/m3, liquefaction did not occur at earthquake magnitudes of 7.0 or 7.5 nor at any depth but liquefaction occurred at magnitude 8.0 between 0 m and 14.5 m; below 14.5 m, liquefaction does not occur.

Jan 1, 2007

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By G. T. Lapidus, J. Trejo-Gallardo

A phenomenological model is presented for leaching silver from silver sulfide contained in mineral particles with ammoniacal thiosulfate solutions of copper in stirred reactors. Experimental results were used to adjust the kinetic parameters of the model, such as the reaction order and velocity. The incorporation of the cuprous sulfide-silver sulfide equilibrium at the reaction interface allowed the prediction of the conversion limits for different reagent concentrations. The information obtained from the reactor model was later integrated into a heap leaching simulation, whose results adequately describe tendencies observed in column tests, with respect to variations in copper and thiosulfate concentrations. Comp

Jan 1, 2005

By Q. B. Li, B. Gonçalves da Silva, J. T. Germaine, H. H. Einstein, Z. Moradian

"Shale gas and oil production has grown rapidly in recent years, and consequently there are increasing demands to understand the mechanical and microseismic properties of shale. Acoustic emission (AE) monitoring provides useful information on the fracture mechanisms of shale rocks, and provides a basis for interpreting field seismic observations. While there have been attempts for microseismic monitoring of conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted to understand the characteristics of the AE waveforms propagated through Opalinus shale rock in the time and frequency domains. Frequency range, arrival time, first arrival amplitude and other parameters such as counts, duration and energy of the waves generated from artificial and natural sources in the shale specimens were detected and compared with AE characteristics of granite, a brittle rock that has been extensively investigated. The experimental tests showed that there are some important factors that influence the analyses and interpretations of seismic surveys and microseismic monitoring of shale compared to granite. One of these factors is the anisotropic behavior of shale that causes the wave to propagate with different velocities in different directions. Also bedding planes and micro-discontinuities in the shale cause attenuation of the waves. Thus the AE waveforms that arrive at the sensor are a distorted and attenuated versions of the source waveform.INTRODUCTIONMonitoring microseismic activity from hydraulic fracturing of shale provides vital information for mapping injection paths and fluid migration in order to check the effectiveness of the hydraulic fracture stimulation. Analysis of microseismic source locations can be used to identify fracture networks induced or mobilized during the hydraulic fracturing operation (Rotherd and Shapiro, 2003). On the other hand, by monitoring and assessing detected signals from hydraulic fracturing one can evaluate the induced seismic impact of the stimulation operation.While there have been attempts to monitor microseismic events in conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted on Opalinus shale to understand its acoustic emission (AE) characteristics in the time and frequency domains."

Jan 1, 2015

By A. Allaire

The Goldex operation of Agnico-Eagle Mines (AEM) commenced operations in the spring of 2008. Following some months of initial operation, the grinding circuit capacity was under-performing according to the original design throughput. BBA Inc. (BBA) was commissioned, in February 2009, to study the different options and recommend the quickest and most cost-effective solution to increase the grinding circuit throughput rate. The mandate was to increase the throughput of the grinding circuit to beyond the original design of 7,000 tpd to 8,000 tpd or greater, while retaining the existing SAG and ball mills. The circuit was modelled using JKSimMet software to evaluate the different options, each with a number of different operating parameters. The option of secondary crushing of the SAG mill feed was retained. Comparison of the different options and simulation outcomes, design of the secondary crushing circuit, operating conditions, and initial adjustments in the design and operating results of the new grinding circuit are discussed in this paper.

Jan 1, 2012

By E. Nurminen

Thermal transport properties of copper flash smelting flue dust have been investigated. Such values of the dust are needed to correctly model the process and to optimize its heat recovery performance. Dust accretions on heat recovery boiler walls may have a significant influence on the boilers heat transfer efficiency. Measurements of the thermal transport properties have been made for industrial flue dust and for pure sulphate components. The measurements have been conducted at temperatures up to 400 °C and the effect of porosity on these properties has also been investigated. The results indicate that the flue dust and the sulphate components are effective thermal insulators and the dust build-up on the boiler walls is likely to greatly decrease the heat transfer efficiency of the boiler.

Jan 1, 2007

By Yusuke Yamamoto, Mineo Asano

"The present study investigated the texture transition during secondary recrystallization in the AA5182 sheet. During the initial stage of annealing, the texture showed a weak Cube orientation as the primary recrystallization texture. During the secondary recrystallization with abnormal grain growth, the area ratio of the {hkl} <011> orientations increased by consuming the other orientations. The texture transition was calculated by the 2-D Monte Carlo simulation with the misorientation dependency. When the higher grain boundary mobility was set in the specific range of the high angle misorientation, the orientation preferential growth of the RW {100} <011> orientation was reproduced. However, other {hkl} <110> orientations could not be well reproduced by the misorientation dependency.INTRODUCTION Crystal orientation and texture are important factors for aluminum sheet products from the standpoint of mechanical property, formability and isotropy. The recrystallization texture results from the orientation preferential growth from the rolling deformation microstructure and the texture (Alvi, Cheong, Suni, Weiland, & Rollett, 2008). Texture development has been a topic of intense research for decades with advances in analysis methods, e.g., orientation mapping (OIM) and computer simulations (Fjeldberg & Marthinsen, 2010; Ivasishin, Shevchenko, Vasiliev, & Semiatin, 2006). The grain boundary characteristic is considered to be a key for the orientation preferential growth. In the case of the recrystallization from the deformed microstructure, not only the grain boundary characteristic, but also the dislocation density and the subgrain size affect the nucleation and the grain growth (Engler, Löchte, & Hirsch, 2007). On the other hand, in the case of secondary recrystallization, the dislocation density and the subgrain size can be ignored and the effect of the grain boundary characteristic can play a significant role in the grain growth. There is intense research about the texture development during secondary recrystallization in aluminum alloys and it was reported that coarse {hkl} <011> grains were formed during the secondary recrystallization (Suk, Shin, & Huh, 2006; Rios, & Gottstein, 2001). However, the mechanism of forming the {hkl} <011> grains has not been fully clarified. In the present study, the effect of the grain boundary characteristic on the orientation preferential growth was investigated by EBSD analysis and Monte-Carlo (MC) simulation."

Jan 1, 2018

By J. Mirza, E. Nicol, J. Lipkowski

Gold passivation in thiosulfate leaching media is a major barrier to its implementation. Addition of Cu (II) into the leaching solution has shown to aid in gold dissolution, but the mechanism by which it acts, and its role in the passive layer, remains unknown. Surface Enhanced Raman Spectroscopy (SERS), in tandem with linear sweep voltammetry, were employed to determine the dependence of leaching currents on mass transport and for fingerprint identification of sulfur species on the surface of gold. SERS leaching experiments were performed using gold nanorod electrodes that showed increased stability compared to other SERS active surfaces.

Jan 1, 2011