Search Documents

? A BARGE WILL BE INSTALLED IN THE BOTTOM OF A COMPLETED PIT. ? THE PROVEN BAUER CUTTER TECHNOLOGY WILL BE INSTALLED ON THE BARGE AND A DEWATERING PLANT WILL BE INSTALLED NEAR THE BASE OF THE PIT RAMP. ? THE WATER LEVEL IN THE PIT WILL BE RAISED BY 20- 40 METRES AND REMAIN CONSTANT OVER DURATION OF MINING. ? THE CUTTER WILL BE LOWERED TO MINE 10 METRE DEEP BENCHES ON A CHECKERBOARD PATTERN TO AN ULTIMATE DEPTH OF 200 METRES. ? THE 5? MINUS CUTTINGS WILL BE PUMPED TO THE DEWATERING PLANT, DEWATERED, AND TRUCKED TO SURFACE.

May 1, 2003

By K. Krishnapisharody, S. Clark, M. Barati

Different gas purging methods to metallurgical baths have been applied to date, among which are top lancing and bottom blowing through tuyeres or porous plugs. Among these, the porous plug bottom blowing technique has shown higher efficiency in gas utilization than tuyeres and top blowing, due to smaller bubble size and lower liquid velocity. However, the studies related to bottom stirring of metallurgical baths are limited to slag-less or thin slag-covered melts. In particular, there is no examination of stirring ability in conditions similar to Falconbridge's Slag Make Converter, where the bath is covered with a thick slag layer and a stream of solids is charged on the bath from top. This study was undertaken to investigate the application of gas purging through a porous plug in stirring in and melting of the solid feeds. The spreading behaviour and melting time of a solid layer forming on a plume created by stirring were calculated using the existing models. The results show that formation of a thick solid layer, specifically in areas beyond the plume region is very likely. Nevertheless, the thickness of the layer and melting time do not appear unreasonably high. It is predicted that by proper controlling of gas flowrate and plug configurations, successful solid charging through the mouth can be practiced.

Jan 1, 2007

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By I. L. Sills

Introduction So many minerals and mineral products are used in the glass industry that it would require an unduly long paper to deal adequately with all of them. Only those that go to make up the batch for the more common types of glass will be discussed here, and even with these only, the list is a lengthy one. It is true that for the body of the glass comparatively few materials are required-as silica sand, soda-ash, lime, and feldspar. The others are used mainly to colour or decolorize the glass, or to give it some other desired characteristic, such as high lustre, greater physical strength, or opalescence; but, although they may be present in very small quantities, they are just as in-dispensable to the glass industry as are the main constituents of the batch. Sand Sand is essentially quartz, the dioxide of silicon, Si02. Most glass contains from 71J to 75 per cent silica. Sand for use in the glass industry, or 'glass sand', is obtained both from deposits of unconsolidated material, commonly referred to as 'sand', and from solid rock-sandstone, quartz, or quartzite. For the manufacture of glass, the material must possess a high degree of purity, as noted below, so that, although sand is widespread in most parts of the world, and sandstone, quartz, and quartzite are not at all uncommon, it is only in certain places that suitable deposits are found. At the present time, most of the glass sand used in Canada is imported from France, Belgium, and the United States. The French material, from Fontainebleau, near Paris, is known the world over as a very high quality glass sand. That from Belgium is nearly as good and is lower is price.

Jan 1, 1934

By M. C. Harris

"Excess Gibbs energy is a thermodynamic parameter which quantifies the difference between the value of the Gibbs energy for a real mixture and that for an ideal mixture. More specifically the partial molar excess Gibbs energy of a species (i) in a mixture is indicated by the change in the overall excess Gibbs energy of the solution as the number of moles of species (i) changes while keeping temperature, pressure and the number of moles of all other species in the solution constant. Generally it is obtained from the activity coefficient which in turn can be obtained for a species in a mixture using a variety of models. The most widely used method is to use UNIFAC. Flotation is probably the most important process in the concentration of minerals and requires the use of reagents such as collectors and frothers. There is abundant experimental data which illustrates that collectors of different alkyl chain lengths will change the contact angle and that frothers of different structures and molecular weights will result in changes in key flotation properties such as froth behavior, surface tension and critical coalescence concentration. In this paper it is shown that there is a strong linear relationship between measured parameters such as froth volume/height, surface tension, critical coalescence concentration and contact angle and the partial molar excess Gibbs energy of the molecules used. Proposals are made to explain these correlations.INTRODUCTIONAs is well known froth flotation is arguably the most widely used process in the separation of minerals. In broad terms the process relies on the use of reagents known as collectors to adsorb onto a mineral surface and thus render the mineral particle hydrophobic. Alkyl thiolates are very commonly used for this purpose. The hydrophobicity is induced as a result of the alkyl group’s molecular structural properties which results in it forming a non-ideal mixture with the process water. Surfactants (or frothers) are typically alcohols and are known to lower the surface tension of the system and also inhibit bubble coalescence and reduce bubble size. Since alcohols are polar they will also form a non-ideal mixture with water. The hydrophobic mineral attaches to the bubble and rises to the froth phase where the valuable mineral is recovered as a concentrate. Frothers have often been characterized using the so-called HLB (hydrophobic-lipophilic balance) number but recently it was shown that the use of activity coefficients (?) or excess Gibbs energy (G ex ), which is calculated using equation (1) is a much more appropriate way to describe the behavior of these reagents in non-ideal mixtures with water (Corin and O’Connor, 2014)."

Jan 1, 2016

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

When underground extractions occur beneath or in close proximity to valleys and other forms of irregular surface topographic features, the observed vertical subsidence at the base of the valley is less than that would be expected in flat terrain, while the valley sides are observed to move inwards towards the centre of the valley. The reduction in subsidence at the bottom of the valley is referred to as upsidence and the convergence of two sides of the valley is termed valley closure. Research coupled with mining experience over the past few decades in Australia has identified valley closure subsidence as being very real and quite significant part of non-conventional subsidence effects, which always have adverse effects on natural features, with risks to water flow and aquatic ecosystems. In this paper, we describe a threedimensional numerical modelling approach to investigate the geomechanical mechanisms which cause the valley closure subsidence behaviour, using distinct element computer package 3DEC. The calibrated models can accurately predict subsidence and horizontal displacements, and they are subsequently extended to specifically study the effect of a series of mining geological and topographical factors on valley closure subsidence phenomenon, by developing a range of hypothetical scenarios. Previous analyses carried out using a two-dimensional numerical modelling technique have identified the potential parameters that affect the valley closure subsidence, which mainly include longwall position, horizontal stresses, valley sloping angle, and valley shape. Further three-dimensional analyses regarding the relationships between the major factors and valley closure subsidence are discussed in this paper. The results have significant implications with regard to both the underlying mechanisms that lead to this nonconventional subsidence behaviour, and how these should be incorporated in future valley closure subsidence prediction and mitigation of its impacts on natural features.

Jan 1, 2015

By G. Van Weert, O. Wang

"As part of a general review of processing double refractory ores through Barrick Gold’s autoclaves / CIL facility at Goldstrike, blanking the preg robbing native carbon in the process solids with hard (m.p. 55 - 60 º C) paraffin wax was studied, specifically in relation to pressure oxidation. The improvement in CIL gold extraction was found to depend on the wax addition point, with hot, dry contacting of the ore in the presence of wax - prior to POX - yielding the largest, most consistent improvement in gold extraction.INTRODUCTIONDouble refractory gold ores present two barriers to gold extraction. The first is generally a physical barrier: the gold is encapsulated or dispersed in a matrix which is impervious to the gold lixiviant. In most cases, including Carlin Trend, NV, deposits, this involves a pyrite or arsenopyrite matrix, although minor gold may also be dispersed in competent silica (quartz) or iron oxides. Gold can be rendered accessible by oxidative destruction of such sulphide matrices. At Goldstrike this is practised by roasting and autoclave oxidation (Thomas, 1994). It is the latter route to which this paper refers.The second barrier refers to the actual gold recovery. Gold may be extracted from the pressure oxidized solids with cyanide, forming a gold cyanide complex. One characteristic of this complex is that it adsorbs on graphitic surfaces. This is taken advantage of on a large scale by gold millers, who use manmade activated, i.e., graphitized carbon particles to remove the gold from solution during leaching: the Carbon-In-Leach, or CIL process. The gold cyanide bearing carbon particles are larger than the ore solids and can be separately recovered by screening. Goldstrike uses the CIL technology to recover gold. The second barrier becomes problematic when the ore naturally contains graphitic orcarbonaceous material, hereafter referred to as native carbon (versus the man-made activated carbon). This material may also adsorb gold cyanide in competition with the activated carbon. Since the native carbon is ground with the ore it is much smaller than the activated carbon. Any competition between the two carbons may produce a loss of gold from the pregnant leach liquor to the process tailings. This phenomenon is called “preg robbing”. Goldstrike ores come from the Carlin trend, which is known for the occurrence of native carbon (Adams & Burger, 1998; Schmitz, Duyvesteyn, Johnson, Enloe & McMullen, 2001; Tretbar, 2004)."

Jan 1, 2012

By S. Kelebek, U. Demir, T. C. H. Richards, E. Koss

"Laboratory-scale tests were carried out to investigate the response of a high-grade (~143 g/tonne) well-liberated gold ore to flotation using two collector types. Octyl and amyl xanthates, representing conventional types of collectors, were tested against an n-octanoic and hexanoic acids under moderate and high redox potential conditions. The latter was based upon a suggestion in literature that monocarboxylic acids are able to adsorb onto the surface of gold at redox potentials near 600 mV (SCE). This investigation did not demonstrate that these carboxylic acids could function as collectors for gold in real ores. In fact, they appear to have slightly depressed gold. However, the results demonstrated that octyl and amyl xanthates acted as highly effective gold collectors for this ore and that an increase in the collector dosage led to an increase in recovery for all mean particle sizes. In some tests, gold recoveries of around 95% were attainable in concentrates with grades around 6 kg/tonne, indicating that xanthate flotation remains a viable means of concentrating gold even at coarse grain sizes. Various aspects of the process such as grade-recovery performance and recovery by size are discussed.INTRODUCTION Three methods are used for the recovery of gold in mineral processing, either alone or in combination: gravity concentration, cyanidation and flotation. Gold occurs as a by-product in some ores together with platinum group metals and as the primary metal in other ores in the form of native gold and electrum, which are alloys of gold, silver and minor amounts of copper. Flotation is a viable method for recovering liberated gold where the gold is visible under an optical microscope (greater than 1 µm in size) and where the attachment of gold grains is not prevented due to bubble loading by competing minerals. It is generally known that grains finer than 150 µm in size will float with most collectors."

Jan 1, 2017

By A. Warczok, T. A. Utigard

"Slags from smelting of copper concentrates contains from 1 to 15% of copper. Copper is present in the form of copper or copper matte inclusions of size from 2 to 1000 micro, and as dissolved cuprous oxide. Removal of the copper requires the slag reduction, primarily reduction of magnetite and co-reduction of cuprous oxide. Thus, the kinetics of the slag reduction play an important role in copper recovery. Instantaneously, at the contact of carbon and a slag the gaseous film is formed. The magnetite and cuprous oxide reduction is going through a gaseous film, separating the slag and carbon of a coke or electrodes. The thickness of a gaseous film grows to a critical value and gas bubbles, containing CO and CO2, are created and rise up in the slag. Results of measurements of kinetic of the slag reduction with graphite showed high value of activation energy, close to the value of activation energy of Boudouard reaction. Strong temperature dependence of the reaction rate points out the thermal instability of the reacting system. It was found that the slowest process in the reduction stages determines the loop of CO and CO2 transfer and magnetite diffusion to the slag/gas film boundary. Strongly endothermic Boudouard reaction seems to cause thermal instability on the reaction surface. So, heat transfer to the reaction surface is very important. Due to low thermal conductivity of a slag the convection dominates in the heat transfer. So, any slag stirring accelerates the rate of reduction and coalescence of metallic copper or copper matte inclusions."

Jan 1, 2015

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By H. Memarian

In the last few decades, many developing countries have tried to expand and improve upon higher education, which is acknowledged to be the leading factor for development. In this respect, develiping countries have significantly increased the number of tertiary institutions and their students. These rapid expansions, along with all the benefits, have drawbacks as well. An example is the status of mining engineering education in Iran. Presently, the number of active mining engineering departments in Iran (27) is more than the sum of similar departments in Canada, Australia, the United Kingdom, and South Africa (23 altogether). Also, the number of annual mining graduates in Iran (645) is more than the cumulative graduates of the United States, Canada, the United Kingdom, and Australia (613). The expansion of mining engineering education in Iran has coincided with the closing or merging of similar mining departments, as well as a decline in the number of interested students in the industrialized world. The present study shows that the need for development and the excessive number of high school graduates, resulting from high population growth in the early 1980s, are the two primary factors influencing the significant expansion of mining engineering education in Iran.

Jan 1, 2007

By L. B. Tsymbulov, N. A. Fedorova

The equilibrium of exchange reaction (Cu20)+[Ni]=(Ni0)+2[Cu] taking place in the course of interaction of metallic nickel-containing copper melts with different oxide melts (Cu20-NiO, Cu20-NiO-Si02, Cu20-NiO-FeO(Fe203)) in the area of their homogeneity has been studied. The studies, based on the known value of equilibrium constants and defined copper and nickel activity indices in metallic melts and equilibrium concentrations of Cu, Ni, Cu20 and NiO, determined the YNio/ycu2o ratios in the oxide melts of the above systems. For the equilibrium between nickel-containing copper and binary oxide melt Cu20-NiO, values of YNiO and Ycu2o were determined both by calculation and experimentally. Based of the data conclusions regarding oxide melts construction are presented.

Jan 1, 2007

By J. B. McKay

It is the purpose of this paper to present an initial report on the construction and operation of the Fluo-Solid roaster at the property of Campbell Red Lake Mines, Ltd., Balmertown, Ontario. The roaster prepares for subsequent cyanidation the bulk flotation concentrate obtained from four hundred tons per day of gold ore. The mill flow-sheet 'includes jigging and amalgamation; flotation; cyanidation of flotation tailing; and roasting followed by cyanidaition of flotation concentrate plus amalgamation tailing. Overall mill recovery for the year 1950 was 90.2 per cent. Recovery possible by straight cyanidation of this ore would not exceed 80 per cent. The ore contains considerable arsenopyrite and pyrrhotite as well as pyrite, with lesser quantities of nickel, zinc, and copper minerals. The mineralization is for the most part extremely fine. The roaster first went into operation on August 7th, 1949, and at the end of 1950 it had roasted 10,916 tons of concentrate. The average recovery of gold from calcine during that period was 94.86 per cent in the primary stage of calcine cyanidation. The average assay of calcine residue from primary cyanidation for the entire period was 0.37 oz. per ton. Both laboratory tests and plant metallurgical balance calculations indicate a further recovery of approximately 10 per cent of this 0.37 oz. when the calcine residue is again cyanided, in the flotation tailing cyanidation circuit.

Jan 1, 1951

By J. G. A. Stevenson

GENERAL Location of Property THE Stirling zinc-lead-copper deposit is in Richmond county, Cape Breton, about a quarter of a mile southwest from Stirling P.O., and some 45 miles southwest from Sydney. The property is accessible by road for at least nine months of the year, and during the navigation period coastal boats maintain a service touching at the port of Fourchu, eleven miles from the mine. When flying conditions permit, the Cape Breton Flying Club, of Sydney, will carry passengers to or from the property, a service which has been particularly advantageous on two occasions when hospitalization was urgently required. The Company has mining rights on leases Nos. 73-74, 78-80, and 101-104, inclusive, and owns 166 acres at Stirling and one acre at Fourchu. The ore deposit is in lease No. 73. History The Stirling deposit was discovered in the 'nineties', probably about 1895. The original discovery is said to have been made in the bed of Copper creek, which traverses the ore-zone. For a number of years, indifferent development work was carried on with a view to copper production only, and it was not until1915-16 that attention was directed to the possible production of zinc. Previously, the ore had been considered too complex for metallurgical treatment. During the period 1916-24 several operators attempted to develop the property, among them being the Stirling Exploration Company, Stirling Mining & Smelting Company, New Jersey Zinc Company of New York, Hayden & Stone Company of Boston, and The Eastern Mining & Milling Company. Up to 1924, the work was limited mainly to trenching, stripping, ? diamond drilling, and shot drilling.

Jan 1, 1937

By Hal. Oliver

MR.]. G. TRAILL: My only excuse for contributing to the discussion on Mr. Hall's interesting paper is that I had the good fortune to be employed at Noranda during those romantic years, 1927 and 1928, when construction was at its height. The mine was in course of being rapidly prepared and brought into production, and the initial difficulties in crushing-plant and smelter were being met and overcome. They were stirring days, and perhaps those members who were with the second Empire Mining and Metallurgical Congress in 1927 sensed the atmosphere of excitement and activity that prevailed. Early History. Noranda must surely possess some of the most remarkable ore-bodies known to mining men, and the story of their development is pure romance. Ed. Horne's faith in the property, and the persistence of Thomson and Chadbourne, were richly rewarded in the end, but only after some very thin times had been experienced. In those early days access to the district was by the Kenojevis river and various portages to Osisko lake, on the shores of which the mine and smelter and the town of Noranda now stand. But all the early work was done on the Chadbourne claims, more than a mile to the west; through the b~sh. I have read a log of the events of that period, and through the whole tale of hard work, discouraging developments, occasional shortages of food, and constant danger from forest fires, can be read the faith and persistence of the men in charge. The Chadbourne ore was of that well-known type which, though just too low-grade to pay (with gold at $20 per ounce), is yet sufficiently encouraging to lead one on in the hope of striking something better. It was only as a last resort that work on the Chadbourne claims was suspended and a diamond drill brought to the gossan-covered hill beside the lake. The diamond-driller told me his version (it may be exaggerated) of how the position and direction of the first hole were decided on. He was told, "You might as well set up your drill here, and drill in, say, that direction". I believe that the first hole went through the richest ore ever found at Noranda. After the drill had gone through about 150 feet of solid sulphide ore running 17 per cent copper and 4 dwt. of gold per ton, it passed into barren rock, but the diamond-driller expressed the opinion (I wonder how he knew)) that the hole would come into ore again before long.

Jan 1, 1937

By Gyeonghye Moon, Inhyeok Choi, Jyothi Rajesh Kumar, Jin-Young Lee

"This paper deals with the recovery of the tungsten and vanadium from spent SCR catalyst leach liquors by different hydrometallurgical methods. The first part consists of pressure leaching of spent SCR catalyst using caustic soda followed by metal recovery by liquid-liquid extraction. In a leaching process, the following experimental parameters were tested and optimized: NaOH, particle size of feedstock, temperature, and solid to liquid ratio. The optimum condition for leaching of tungsten and vanadium was under the following conditions: NaOH 3 mol/L, temperature 250°C, particle size <300 µm, and solid to liquid ratio 0.4. From these optimum conditions in this experiment, the dissolution efficiency of vanadium and tungsten was 91.5and 87%, respectively. Liquid-liquid extraction following commercial extractants were tested: TBP, Cyanex 272, D2EHPA, Aliquat 336, Primeme JM-T, Alamine 308, Alamine 304-1, and methyl-tri-octyl-ammonium chloride. The conditions for both valuable metal recoveries were optimized.INTRODUCTIONSelective Catalytic Reduction (SCR) catalyst has become the most effective to reduce nitrogen oxide (NOx) emissions from stationary segments such as power plants and waste incinerations around the world due to the reinforcing regulatory trend and emerging environmental issues (Forzatti, 2001; Spivey, 2002; Li et al., 2011).Currently, the most widely used SCR catalyst is V2O5-WO3/TiO2 system due to its great catalytic properties (Li et al., 2011; Marshneva et al., 1995; Marbergeret al., 2015). In general, the composition of the SCR catalyst used in the stationary application is 0.5 to 1 wt% of V2O5and 7 to 10 wt% of WO3(Marberger et al., 2015; Chen &Yang, 1992, Vuurman et al., 1991; Alemany et al., 1991). Currently spent SCR catalysts are treated as waste and disposed of in landfills. This causes a lot of waste of secondary resources of vanadium and tungsten. In terms of industrial value of vanadium and tungsten (Gupta &Mukherjee, 1990; Moskalyk &Alfantazi, 2003) and reduction of pollutant emissions, it should not be disregarded for their recovery for their material recycling from spent SCR catalyst. However, investigations for recovery of metal values from spent SCR catalyst has been rarely carried out."

Jan 1, 2017

By E. A. Davies, Trevor T. Jones

"Aspects of materials, design and operation of suspension equipment is dealt with, hazard, fatigue and special metallurgical properties of certain steels to resist are described, as is the effect of temperature in service modifying the properties of some steels to resist stress concentration and propagation of cracks.The influence of steady impact and fatigue loading and its results are described. Control of manufacture including nondestructive testing is outlined and acceptance parameters and strength calculations are given. Quality requirements and control in manufacture are outlined. A short description of the overwind detaching hook, together with illustrations of the operation of detachment are presented.MaterialsWinding engine ratings of 8000 h .p. and large capacity shafts 2000 m in depth (4000 m depths have already been reached and it may be necessary to go to 6000 m) and up to ten conveyances are not uncommon today. Loads of 100 or even 200 tons hoisted at low speeds are possible within the near future. Some of these appliances are designed to protect lives and installations in hazardous conditions when, due to human or mechanical fault, a malfunction occurs in the system. In addition, such equipment includes suspension gear of various kinds designed to anchor and apply high mechanical tensions to numerous steel ropes installed in shafts necessary either for the safe passage of conveyances or for balancing purposes when heavy loads are in motion.No unique metallurgical problems are presented in underground mining operations, but they have two special characteristics that influence the metallurgical aspects of the de sign of suspension gear and other equipment concerned in the transport of men and materials. (1) Any uncontrolled release of energy caused by the unexpected failure of a component is more likely to injure personnel and cause costly damage to installations in the narrow confines of an underground mine shaft. (2) Some mechanical equipment in mines, tends to be overloaded in service and suffer plastic distortion."

Jan 1, 1987

By V. G. Papangelakis, G. A. Moldoveanu

"Rare earths adsorbed on clay minerals are easily recovered via ion exchange during leaching with inorganic monovalent salt solutions. The leaching efficiency of various salts at 0.5M and 25°C was investigated as a function of cation type and salt system (sulphates vs. chlorides). (NH4)2SO4 was identified as the lixiviant of choice and a procedure was established to investigate the influence of lixiviant concentration, temperature, pH and agitation on desorption kinetics and REE extraction levels. It was determined that the kinetics were fast and the optimum leaching conditions (for >80% total REE extraction) required pH below 5 and moderate temperatures (<50°C). INTRODUCTIONRare earth elements (REE) are at the core of numerous advanced applications due to their various uses in high strength permanent magnets, lasers, automotive catalytic converters, fiber optics/superconductors, and electronic devices (as phosphors in TVs and display screens for computers and cell phones). Because of the ongoing development of new technologies, there is an increased demand for REE in the international market, with emphasis on identifying new resources to insure an adequate supply for present and future use. World production of rare earths is dominated by China, the United States and Australia; however, in terms of resources, China dominates the world potential with reserves estimated to be over 90% of the total (Chen, 2011).The main commercially significant REE sources, as reviewed by O’Driscoll (1991) are bastnasite (carbonate) and monazite (phosphate) minerals, containing up to 70% wt. rare earth oxides (REO). In spite of being high grade, these ores are associated with elevated recovery costs due to difficulty in mining, separation and beneficiation. Moreover, aggressive conditions are required to solubilize the REE from the mineral, such as leaching with hot, concentrated acids or baking in 70% NaOH (Gupta & Krishnamurti, 2005)."

Jan 1, 2012

By J. -F. Blais, M. -O. Simonnot, J. Mocellin, G. Mercier, J. -L. Morel

Large quantities of ferromanganese sludge are generated as waste material by blast furnace during the manufacturing of ferromanganese. These slags are very rich in manganese, zinc and lead (5 to 40 %). These residues have been deposited in a pond in periphery of the steel industry. Considering the market value of the metals, these brownfield sites can now be considered as secondary resources. We have developed a hydrometallurgical process for selectively leaching Zn, Mn and Pb in order to produce compounds of Mn and Zn pure enough to be economically recoverable and a residue rich in Pb. Batch laboratory experiments were carried out to determine appropriate leaching conditions to maximize zinc extraction (100 %) and manganese extraction (90.0 %) with sulfuric acid and to generate a residue containing 15 to 30% of lead. This Pb residue is recyclable by another process.

Jan 1, 2015