Search Documents

By A. N. May

"This paper describes the present approach of the Mines Branch to the problem of measuring the stress condition in the interior of rocks surrounding underground openings. An instrument, which will be referred to as a stressmeter, has been developed at the Mines Branch to measure un-directional stress changes in absolute units. There are two modes of operation of this stressmeter. It can be regarded as a fixed instrument, in which case it is installed at the end of a diamond drill hole and left in position to record any subsequent stress changes taking place. Alternatively, three of the stressmeters can be used in conjunction with a trepanning opera-tion to allow the existing stress condition to be determined. The initial laboratory work and subsequent experiences in the field with the stressmeter are described. All the field development work on the stressmeter was made possible through the co-operation of Canadian Refractories Limited, Kilmar, Quebec."

Jan 1, 1960

By A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia?s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By Zhiqiang Wang

This paper mainly focuses on the method of ?three-zone? definition (a caving zone, a fissure zone and a curve subsidence zone) for full height cutting in a thick seam. Based on criteria of a caving zone and a water conducting zone, as well as existing research achievements, it is believed that there exists great error for calculation of height of the ?three-zone? area using cutting height and the coefficient of bulk increase. Dynamic factors should be considered, so, based on the theory of key rock strata and combining this with several other factors, such as mining area, this paper presents a new method to determine the overburden ?three-zone? definition. The results are as follows: (1) geometric models of a working face and key stratum are established through the rock displacement angle, with consideration of the influence of mining on the key stratum (the range of key stratum influenced by mining is enlarged as the mining area increases); (2) because there is always a cavity below the key stratum of the thick coal seam with full seam cutting, and the key stratum gradually fracture with face advancing, based on the geometric dimension of strata, the maximum fracturing interval expression has been presented, including the working face advancing range. This can theoretically lead to the location of the key stratum influenced by mining, and its stability before mining, helps to confirm which zone the key stratum and following-up strata belong to, using the criteria of sliding instability or deformation instability; (3) the new method of ?three-zone? definition which is based on the theory of key rock strata is first proposed for full height cutting in thick seam. Finally, combined with practical engineering, and comparing with field data, it is believed that the proposed method is more objective than existing methods.

Aug 1, 2013

By Sengpasith Houngaloune

Arsenic, which is a toxic and carcinogenic element, causes serious environmental problems throughout the world. It is also known as a major contaminant in the non-ferrous mining and extractive metallurgical industries, thus its disposal is one of the most important environmental issues for the mining and metallurgical industries. In order to ensure a safe disposal environment for the final wastes, stabilization of arsenic has been studied extensively with various approaches. Solidification/stabilization (S/S) represents one of the most effective methods to reduce the availability of arsenic in soil and waste by transforming toxic or potentially hazardous phases into less hazardous ones. Cement based S/S processes could reduce the solubility of arsenic in solid waste, using inorganic binders such as cement, lime, and pozzolanic materials. A new tailings management technique, called cemented paste backfill (CPB), has become widely employed for improving mining techniques and for tailing storage purpose and this technique could also enhance arsenic stabilization, by fixing the contaminants in the binder matrix. Disposal of arsenic in the form of scorodite (FeAsO4?2H2O) has been widely accepted as currently the most suitable method for stabilization and the safest known storage material. The Bio-scorodite process has been reported to be more economic and environmentally friendly method than the chemical crystallization processes. Retention of arsenic by schwertmannite (Fe8O8(OH)6SO4), a metastable ferric oxyhydroxy sulfate mineral, has gained more attention in the recent years. Schwertmannite has a large specific surface area and high capacity to adsorb arsenic in solution. Several researchers have reported that the transformation of schwertmannite to goethite could be retarded by the presence of adsorbed arsenic; therefore schwertmannite might be viable alternative for long-term storage of arsenic. In this paper, various approaches used in arsenic stabilization are reviewed with emphasis on the development in the recent years.

Aug 1, 2013

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

"Energy efficiency in mining and minerals processing has attracted considerable public and industry attention because of the significant quantities of energy consumption involved. In this context the question of what are worthwhile targets for energy efficiency improvements ought to be of the highest priority. It is however worth taking a step back to avoid falling in the trap of taking preconceived ideas that have been reiterated repeatedly before as gospel. The aim of this paper is to highlight areas where new or alternative approaches could potentially be the better way forward. Some may come as a surprise to conventional industry thinking. Ultimately any such solutions are attractive to practitioners not just in an environmental but also in an economic sense, and hence should be targeted through applied research and development efforts. This paper highlights key aspects of each group of opportunities and some of the individual approaches to provide an overview of the current status quo.MINING INDUSTRY POWER UTILISATION – WHERE IS THE BIGGEST BANG FOR THE BUCK?The question of where is the biggest bang for the buck when trying to determine worthwhile targets for energy efficiency improvements has not always been reported on broadly enough, typically because industry practitioners operate in specific areas of expertise and comfort zone. Looking beyond the familiar doesn’t always come easy. Any technology or methodology consideration to address energy efficiency needs to take into account the context of alternative opportunities of superior value or risks not achieving desired uptake. The following sub-chapters have been ordered by magnitude of improvement potential as best as is possible, starting with the biggest first, and the smallest last. Some may be a surprise relative to conventional mining industry thinking."

Jan 1, 2016

By Phil A. Keele

"IntroductionGeneralThe Genesee Coal Mine is a joint venture of Fording Coal Limited and the city of Edmonton. The mine supplies thermal coal to the Genesee Generating Station operated by Edmonton Power and is located approximately 75 km southwest of Edmonton (Fig. I).Under the terms of the joint venture agreement, Fording Coal Limited has designed and developed the Genesee Coal Mine. Fording also operates the mine which has a minimum economic life of thirty-five years. Mine development started in the spring of 1987 with the construction of the dragline erection pad and mine service complex. Major development of mining areas was carried out in 1988 with the construction of haul roads, powerlines, topsoil recovery, etc. Mining officially commenced on December 14,1988.The mine produces 1.6 million tonnes of coal per year and employs 65 people. MiningGround conditions have turned out to be very poor, as expected with the majority of the overburden in the first few years a soft lacustrine clay with minor amounts of fine-grained glacial till. To compound matters, what was expected to be a relatively uniform coal subcrop turned out to be a very irregular erosional contact.The coal mined at Genesee is a sub-bituminous Class B thermal coal with approximately 16070 ash, 21% moisture, 8300 Btu/lb and 0.27% sulphur on an as-mined basis.The primary piece of mining equipment used at the Genesee Coal Mine is a M8200 walking dragline. It has an effective operating radius of 100.6 m, a 50.5 m3 bucket, and weighs approximately 3860 tonnes yielding a ground pressure of III KN/m2•Figure 2 illustrates schematically the single pass mining sequence presently employed at the Genesee Coal Mine. The M8200 is used to lift all coal out of the cut, the coal being placed in stockpiles on the prepared pad .This method maximizes coal recovery under the conditions where spoil failures due to poor material would otherwise put men and equipment at risk. The coal is subsequently loaded by the coal shovel operating on the same bench as the M8200 dragline and delivered to the plant as required.All mined areas, as required under Alberta Legislation, are to be returned to an agricultural land capability equal to or better than that which existed prior to mining. Reclamation activities, as a result, are an important and integral part of the mining process. A complete list of the primary mining equipment deployed at the Genesee Operations appears in Table I."

Jan 1, 1994

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By P. Z. Caverhill

In this section of the province only the most meagre of surveys have been made and because these are not sufficient to determine with any degree of accuracy even the total forest area, the information presented in this paper is not complete. Area: -The area south of the Canadian National, and served by the Pacific Great Eastern, is roughly 38,000. square miles, 30,000 of which is classed as productive. This is approximately equal to the productive area of Norway, or half of Finland-or of 30 per cent of Sweden. It is larger than that of either Nova Scotia or New Brunswick. Eliminating from the productive area 3600 square miles of grass-land and areas capable of agricultural development, 26,000 square miles (16,600,000 acres) remains as absolute forest-land, as compared with the 55,000,000 acres of Sweden, the 37,500,000 acres of Finland, the 17,000,000 acres of Norway, and the 7,600,000 acres of Austria.

Jan 1, 1925

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

By G. M. Card, K. D. Card, B. V. Sanford

Abstract-The Canadian Shield and its extensions are traversed by an orthogonal system of northwest and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches influenced patterns of sedimentation and tectonism in the intervening epicratonic basins and marginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structures also triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By G. M. Card, K. D. Card, B. V. Sanford

The Canadian Shield and its extensions are traversed by an orthogonal system of north-west and northeast trending arch-style uplifts. These basement arches were formed by repeated vertical movements along pre-existing structures during compressional and extensional tectonism connected with events in surrounding Proterozoic and Phanerozoic orogens and ocean basins. The arches in?uenced patterns of sedimentation and tectonism in the intervening epicratonic basins andmarginal platforms throughout the Proterozoic and Phanerozoic. Movements on the arch structuresalso triggered minor magmatism and controlled the location and timing of alkalic rock-carbonatite, kimberlite, and related intrusions in the Canadian Shield, the Western Canada Sedimentary Basin, and West Greenland.

Jan 1, 1997

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By J. Fujioka, Y. F. Gu, C. Cui, D. Ping, A. Sato, H. Harada

"A new kind of cast & wrought (C&W) Ni-Co base superalloys named as ""TMW alloys"" are developed recently for compressor or turbine disks of gas turbine engines in High Temperature Materials 21 Project at National Institute for Materials Science (NIMS) in Japan. These Ni-Co base superalloys combine the characters of two kinds of y- y' two-phase alloys (Ni-base and Co-18at%Ti alloys) and have higher tensile strength and creep resistance than C&W UNDIMET 720Li superalloy."

Jan 1, 2006

By W. G. Worcester

THE chief object in presenting this paper on bentonite is to attract general attention to one of the least known and most neglected industrial minerals of Canada, a mineral of extensive commercial possibilities, as evidenced by its development and exploitation in other countries, principally in the United States and Germany; countries upon which some of our most important Canadian industries are dependent for their supply of special clays, such as Fuller's earth and activated bentonite. It was in view of these conditions and the knowledge of the presence of large quantities of bentonite in the Canadian West that the work here reported on was under-taken. While the investigational studies have not been completed, the results indicate that among the many samples tested there are some of real merit and industrial importance. While it has been the author's privilege to examine deposits and samples of bentonite from all of the Western provinces, his chief activities in the field and in research studies have naturally been confined largely to Saskatchewan materials. Notwithstanding this, however, this paper is presented in the hope that it may stimulate a more general interest in, and study of, Canadian bentonites as a whole, a matter of such importance that provincial boundary lines should be overlooked. GENERAL CHARACTERISTICS OF BENTONITE According to Schurecht and Donda (1), bentonite is commonly composed of the mineral montmorillonite, (Mg,Ca)O.Al203 5SiO2 .nH2O, though some are known to consist of beidellite, Al2O3 3SiO2.nH2O: where n is approximately 4, and in certain cases the Al2O3 may in part be replaced by Fe2O3. For present purposes, however, it may be sufficient to state that, in general, bentonite is a "soapy' clay-like mineral or group of minerals composed largely of hydrous aluminium silicate, but frequently carrying small percentages of the alkalies, alkaline earths, and free silica, as well as silicates, gypsum, and other admixed detritus such that purification is usually necessary.

Jan 1, 1937

By Christoph Müller

Information exchange for mine process optimization is essential. Today, modern mining equipment uses the IREDES standard to exchange production plans and reports for easy management and storage. To gain further benefits from process optimization, a mine wide access to real-time information is needed as e.g.: The current status of a machine, operational details etc. Presently, real-time data exchange systems are developed by machine producers. Each machine producer uses its own way of gathering, managing, and storing production data. These proprietary mining processes increase the complexity of cross platform data exchange and management for mines which involves machines produced by different vendors. Casting and unifying the data requires much effort. For this purpose, ?IREDES On-line? currently is being introduced. The standard defines an open, web based method for the exchange of volatile real time machine information. Two different principles are used: Web Services for cross platform information exchange within the IT world and the optional OPC UA for use with automation and process control systems. With such a standard information from machines of different vendors may be managed by using one common platform without spending the effort for dedicated interface development. Additionally, information management and storage will become straight forward since all the data are of the same format. The IREDES On-line standard utilizes the latest IT technologies as well as the knowledge and experiences gained from the previous IREDES standard. The paper explains the benefits, the use, as well as the technical design of the standard and gives application examples from the practice.

Oct 1, 2009

By Y. Héroux, A. Chagnon, M. M. Savard

"Résumé- Le gîte de Pb-Zn de Gays River s'accompagne d'anomalies des propriétés de la matière organique (MO) et des assemblages de minéraux d'argile (AMA). L'association entre la minéralisation, la distribution de la réflectance de la MO et des AMA suggère que ces traceurs peuvent servir à l'exploration des sulfures de métaux de base dans cette région.A l'emplacement du gîte, la réflectance varie considérablement (0,80% à 1,88%), pouvant même afficher une baisse avec l'enfouissement, ce qui est interprété comme une altération chimique de la MO. Les valeurs les plus élevées s'accompagnent localement de quelques textures en mosaïque et délimitent une anomalie thermique au centre sud de la région. Parmi les minéraux des argiles identifiés, l'illite et la chlorite sont terrigènes alors que la smectite, la kaolinite et la corrensite sont authigènes et, à l'instar de l'altération de la MO, résultent des nouveaux équilibres chimiques créés suite à la précipitation des sulfures.Abstract- The Gays River Pb-Zn ore deposit is associated with anomalies defined from the characters of the organic matter (OM) and from the clay minerals assemblages. The relationships be­ tween these anomalies and the mineralization at the mine suggest that these parameters can be used as new guides for the exploration for base-metal sulfides in this area.The vitrinite reflectance (RJ shows a wide range of values (0.8% to 1.88%) and exhibits an anomalous suppressive effect with depth of burial at the mine site, suggesting a chemical alteration of the OM. The highest R, values are associated with mosaic textures and outline a thermal anomaly at the south-center of the studied area. Among the identified clay minerals, illite and chlorite are terrigenous, whereas smectite, kaolinite and corrensite are authigenous and, like the alteration of the OM, are due to the new chemical equilibria resulting from the precipitation of the sulfides."

Jan 1, 1994

By R. B. Sudderth, A. Quiroz G., M. Torres M., C. Salgado Q., J. Fernández O., H. Bravo P., M. Torres B.

SNF FloMin, Inc. has introduced a complete line of extractants for recovery of various metals. Among them are the CuPRO MEX™ Brand of copper extractants that are based on the well- known 2- hydroxy 5-nonylsalicylaldoxime and 2-hydroxy acetophenoneoxime. This paper presents the laboratory and pilot plant trial results for SNF FloMin’s CuPRO MEX™ 3302 reagent, the equivalent to the wellknown ACORGA® M5640 extractant, and the composition of these reagents are described. Some examples of SNF FloMin’s CuPRO-Sim™ Advanced solvent extraction simulator are presented.

Jan 1, 2014

By S. Borle

The microstructural features produced in friction stir welded AZ31, AZ80 and AZ91 alloys are examined when different welding parameters are applied. The microstructures primarily consist of a-Mg grains with a-Mg + Mg17A112 colonies, however melted films of Mg17A112 are produced in AZ91 alloy when high rotation speeds are applied. When the rotation speeds are slow, or the travel speeds are fast the Mg17A112 were incorporated into the stir zone, however they do not exhibit an elongated lamellar morphology associated with melted films. In the case of AZ80, the extruded base material contains a smaller fraction of Mg17A112 and few of these phases are observed in the stir zones. The results are explained based on the dissolution rate and melting temperatures of Mg17A112 controlling the overall morophology and fraction of phases in the stir zone.

Jan 1, 2011

By Alfred C. Lane

Reference to the original use of the terms Laurentian and Huronian (and its extension), shows that the former was applied to granitized sedimentary and metamorphic pre-Cambrian rocks, and the gneissoid igneous rocks associated therewith, and the latter to non-fossiliferous rocks supposed to be later. But it appears from the work of Collins, Quirke and others that there is more or less of an overlap, and that of the original Laurentian the Grenville limestone, and some of the granites, may be later than the lowest part of the original Huronian. Before we can decide whether to abandon one or the other of the two terms, or how to delimit them, it is important to know the extent of this overlap. The Pb :U ratio, though not to be depended upon too minutely, does give a real idea of the age of a mineral as it increases with the decay of uranium, and so is greater the longer the time since the uranium was separated: and there are reasonable prospects of help there from in getting a knowledge of the relative age of different granites to assist in solving the problem, as facts already collected show. 1. Historical review of the use of the words Laurentian and Huronian: 2. Difficulty encountered: 3. Popular account of atomic disintegration: 4. Methods of estimating age by it: 5. Applications.

Jan 1, 1925