Search Documents

By R. E. Barbosa

Seepage forces generated during tunnel excavation affect the ground response and may cause severe instability problems, including total ground collapse and flooding into the tunnel. This paper presents a new closed-form analytical solution, for stresses and displacements around a cylindrical tunnel excavated in a porous water-bearing elasto-plastic material, which includes the effects of seepage forces. The analysis is carried out in terms of effective stresses and pore water pressures. The solution shows that seepage forces may have a major effect on the effective stresses around the tunnel, on the extent of the plastic zone, on the radial displacements, and on the tunnel support requirements. The conditions for development of a ?flowing ground? condition at the tunnel face have been identified. The paper presents a procedure for the hydromechanical ground-support interaction analysis, to determine the excavation induced inflow and the pressures acting on the lining, throughout the progressive driving of the tunnel, including the effective pressures exerted by the ground and the pressures generated by the water.

May 1, 2009

By Doug Smith, Gary Taylor, Paul Ogryzlo

"Uranium mining and processing typically requires large quantities of high-grade reactive quicklime for the neutralization and clean-up of contaminated mine water and mill process waste streams. Currently the Saskatchewan uranium industry’s lime requirements are being supplied from deposits located in Manitoba and Alberta, resulting in transportation costs, which equal or exceed the market value of the product. During the summer of 2001, the northern village of Pinehouse located 220 kilometers south of the Key Lake uranium mill, staked two previously discovered limestone deposits. The relatively shallow deposits, known as Missi Island and Sleeping Giant are located in close proximity to one another, approximately 35 km south of Pinehouse adjacent to highway 914. This paper describes the results of a scoping study carried out by AMEC for the development of the two deposits based on a seasonal limestone mine and a continuous 40,000 to 60,000 tpy wood fired calcining plant designed to supply all of the quicklime needs of the Saskatchewan based uranium industry. Also described are the results of calcining and customer acceptance testwork on samples of lime prepared from recent Pinehouse limestone drill core. The potential benefits of the project include a significant new source of revenue for the community of Pinehouse, lower lime costs for the Saskatchewan uranium industry and employment for northerners in the mining, processing and wood harvesting operations.IntroductionInterest in the Pinehouse/Massinahigan River area for limestone was precipitated by the results of a 1977 industrial minerals drill hole program by the Saskatchewan Department of Mineral Resources. These results led to the acquisition of land in the area by Missi Island Mines Ltd who carried out extensive exploration during the period 1978-1982. They discovered a deposit on the southwest side of the Massinihigan River thought to contain approximately seven million tonnes of limestone with an average grade of 94.5% CaCO3. Missi Island carried out preliminary feasibility studies and prepared an Environmental Overview Statement. However, in spite of positive recommendations, the project was dropped in the mid 1980’s."

Jan 1, 2003

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By P. Wells, P. Quinn

"A moveable flotation miniplant was designed and constructed at the research laboratory of Inco Technical Services Ltd. to address the need for flowsheet development with a limited amount of ore (such as drill cores). It consists of one rod mill, two regrind ball mills, one vibratory screen, 24 flotation cells of various sizes and two Venturi aerated flotation columns. The setup has continuous monitoring capability for pH, dissolved oxygen, oxidation-reduction potential, conductivity and temperature in conditioning tanks and flotation cells. Various options regarding flotation reagents, circuit configurations, and fineness of primary grind and regrind can be readily evaluated. The throughput of the miniplant is 20 – 30 kg/hour ore.Unit operations such as flash flotation, magnetic separation and gravity concentration can also be evaluated as an integral part of an entire flowsheet development.This communication describes the basic design features of the miniplant and some examples of applications are given.INTRODUCTIONInco operates numerous mines in Sudbury and Thompson and will shortly bring the Voisey’s Bay mine into production. It has long been recognized that the ores from different mines or from different depths of the same mine can give different responses in flotation. There is a growing need to properly evaluate the ores before feeding the mill to maximize the return of the mine/mill operation. Inco Technical Services Limited at Sheridan Park, Mississauga, Ontario has developed a batch laboratory procedure to address this issue. The results are considered in the overall economical assessment of new mine operations.For ores that cannot be processed by the existing mill operations or that will be processed by a new mill, it is necessary to develop a flowsheet that can maximize the economical return of the mine/mill operation. While recognizing the importance and contribution of the laboratory batch flotation procedure, it does not generate reliable data for flowsheet simulation and design. A full-scale pilot plant campaign is normally required to obtain the design data but often this is not possible due to a limited amount of ore obtainable from the drill core. A small-scale pilot plant (mini pilot plant or miniplant) capable of processing 20-30 kg/h ore can provide this data prior to a full-scale pilot plant campaign. A miniplant can also be used to optimize the circuit configurations, reagent additions and recycle options of process water before pilot plant work and can be used to test a different flowsheet configuration for an existing mill before re-piping a plant circuit."

Jan 1, 2003

By Yum Xiaoquan, Turgut Yalcin

"A laboratory study was carried out to determine the potential role and effect of ultrasonic irradiation in the flotation of a Sudbury copper-nickel sulphide ore. The use of ultrasound was tested separately at the pulp preconditioning, collector conditioning and flotation stages. While no significant benefits were evident in the latter two cases, ultrasonic preconditioning of pulp improved the grade-recovery performance and had the prospect of reducing reagent consumption rates. Tests were conducted on both the normal and oxidized ore samples, and several variables were investigated, including ultrasound frequency (25 kHz and 45 kHz), ultrasonic power (up to 1.6 W/cm2), duration of ultrasonic treatment (up to 60 minutes), and the intensity of pulp agitation employed during the application of ultrasound. Ultrasound frequency of 25 kHz and duration of 15 minutes yielded satisfactory results. Changes were found to occur in the temperature, pH and Eh of the pulp during ultrasonic processing. The favorable effects of ultrasound observed in this study were attributed primarily to its surface cleaning capability.INTRODUCTIONThe use of ultrasound for the surface cleaning of objects is well known. Ore flotation is based essentially on the surface properties of minerals, and hence stands to benefit from ultrasonic treatment which may help restore mineral surface characteristics that might have been lost or modified through oxidation, etc. Expected outcomes of this method of treatment include improved flotation kinetics, higher recovery, better selectivity, and savings in reagent consumption, as has been demonstrated by various researchers (Aldrich and Feng 1999, Celik 1989, Ozkan 2002, Letmathe et al. 2002, Nicol et al. 1986)."

Jan 1, 2005

By Ludwig M. Strah

"Wear is a universal problem and is present in all cases wherein one weighted surface moves with or relative to another surface. A practical description of wear as applied to mineral processing plants is outlined.With the advent of higher material and maintenance costs, more attention is being focused on the field of wear resistant linings. The aforementioned is magnified today as the production facilities continue to be designed to handle larger daily capacities. These changes, higher costs and larger plant handling facilities have necessitated the introduction of different materials and designs to combat the never ending battle against wear.In order that wear be understood, it can be relegated to two specific types:1 - Mechanical Wear - due to movement of one loaded surface relative to another.2 - Chemical Wear - more easily defined as corrosionMechanical wearMechanical wear can be subdivided into two basic forms:A.,Material movementB.,Material impactMaterial movement Abrasion is the result of, as earlier stated, the straight move¬ment of one loaded material relative to another.Material impact Is the striking effect when a mass strikes another from various angles and at various speeds. Impact can be severe enough to permanently damage and distort the basic component installed to overcome impact."

Jan 1, 1983

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemistries are added to flotation circuits directly and indirectly to control issues such as scaling and dust. Since the dosage levels are generally not very large, a standard laboratory float test may not be able to determine the effect a specific chemical has on the productivity of the flotation circuit. Hudbay and Ashland Water Technologies developed a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5 ppm to 500 ppm). Laboratory results indicate that this protocol helps to predict the potential interference that a particular chemistry will have on the flotation circuit.INTRODUCTIONFrom a chemical perspective, flotation is a very complex system involving more than the reagents used for flotation. Along with collectors, frothers, modifiers, suppressants and activators, there can be antiscalants for water treatment, dust suppressants used in the mining process, residual flocculants from recycled thickener overflows, grinding aids, and many other types of chemicals that are added upstream of a flotation circuit. Although these other chemicals are usually used at very low doses, it is important to know if they affect the flotation process detrimentally in the event of a spill or a build up from recycled water.Laboratory flotation testing of these chemicals characterizes their effects, but testing at expected doses in the float can mask the effects of the chemicals in the plant. Also, simple tests that do not measure the kinetics of flotation do not reveal the effects the other chemicals have on the flotation circuit. Thus, a new flotation protocol was needed to expose the full effects of chemical additives and to assist in choosing the chemical with the lowest potential for a negative effect.FLOTATION KINETICSMeasuring recovery kinetics in a laboratory flotation cell is a well-established procedure: analyzing concentrates taken in a timed sequence to determine the recovery rate of individual cells in a flotation circuit. The recovery from the early flotation cells are a true measurement of how well a flotation chemical is performing. The principles of kinetics can be mathematically determined by the following functions (Houston, 2006):"

Jan 1, 2013

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By G. Griffiths

"P. WitteWitteck DevelopmentThe implications of using a tower mill for fine grainding in the ore processing of tailings are significant. What can those of us who are in a research and development situation do when we recommend this equipment to a client? When this prototype is placed on stream next to a conventional grinding mill as you suggest how do we estimate the power requirements and the grind which will be achieved?ReplyLet me explain the Macassa circuit. The tower mill here was running in parallel with one of the ball mills. The feed entering the tertiary system is scalped in a primary cyclone. The finial cut is made in a secondary cyclone. The actual feed to the tower mill is the underflow from the two cyclones and was split to the ball mill and tower mill. During the testing we were unable to isolate the tower mill to determine its contribution to the overall system. We then started to look at the amount of material produced across the mill. We entered the mill at between 17% and 20% finished material and exiting at between 36% and 40% finished material. We were able to project, with a high efficiency classification system, and arrived at 6 Kwh/ton or better."

Jan 1, 1984

By Colin Hardie, Erik Bartsch, Guy Comeau

"The Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik region has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,200,000 tonnes per year due to an Optimization Project (FAG to SAG conversion) in 2005 and many recent processimprovements.In 2006, the Raglan Metallurgical Group with assistance from the Xstrata Process Support group decided to make SAG control one of its priorities in order to further increase throughput and improve stability. The original primary mill control logic delivered by the Optimisation Project in 2005 consisted of a simple PID loop controlling the mill charge (bearing pressure) through feed rate changes. Due to the multivariable, non-linear and disturbance dominated nature of the SAG circuit it was quickly found that this traditional PID control strategy was not able to adequately control the mill; resulting in poor stability, frequent operator interventions and less than optimum performance.This paper describes the successful integration of advanced field systems such as mill feed image analysis (Wipfrag) and crusher gap controller (ASRi), into a multi-variable fuzzy logic SAG mill controller. The process of how a strategy for control was developed and implemented directly in the existing control system (exploiting standard system capabilities) is discussed. It is also shown how this approach has provided mill automation which is simple, robust (despite erratic feed characteristics), and delivers both an increase in throughput and a reduction of variability.INTRODUCTIONOriginally commissioned as a Fully Autogenous Grinding (FAG) circuit in 1997, preparations to convert the Katinniq Concentrator Mill to SAG had in fact commenced as early as 1999, but were halted owing to alternative process improvements which achieved up to 1Mtpa as early as 2000. Up until this time, plant process controls had remained more or less static; modifications having been limited to those required by new equipment. Primary mill process controls and related measurements were at this stage limited to:"

Jan 1, 2008

By Changping Hu, Keqin Tan

In 1937, the Metallurgical Department of the National Resources Committee established a copper refinery plant (predecessor of the Chongqing Smelter) in Changsha, Hunan Province, China. The blister copper produced by a local copper smelter was casted as anode for electrorefining. The plant, with a capacity of one ton of electrolytic copper per day, was designed and tested in 1937. At the trial production stage, a total of 9 tons of cathode copper was produced. The plant was formally put into operation in July 1938. In the same month, more than 20 tons of electrolytic copper with purity over 99.9%Cu was produced. This was the first batch of electrolytic copper produced in China. In 1939, China’s largest non-ferrous metal smelting plant, Fengtian Gold Mine Refining (predecessor of the Shenyang smelter) was completed and put into operation in Shenyang, mainly producing nonferrous metals such as gold and silver, as well as copper and lead. In 1939, the Kunming copper smelter (predecessor of Yunnan Smelter) was completed and put into operation. The plant equipment, imported from the United Kingdom, was designed to produce 1,200 tons of electrolytic copper annually. In 1943, Jiatong smelter (predecessor of the Shanghai Smelter) became the 4th domestic cathode copper producer. Since 1949, China has gradually established a large copper industry. These developments are discussed in this paper. Today, China operates nine out of the twenty largest copper refineries in the world. With a total capacity approaching 9 million tons of copper per year, China has the world’s largest copper refining capacity. INTRODUCTION China is a country with a long history of copper mining. The earliest smelter in China in recent times was the Shanghai Smelter, which was built in 1912. From then until 1949, China successively built Chongqing Smelter, Kunming Smelter and Shenyang Smelter. The world's first copper electrorefinery was the Pembrey refinery built in the UK in 1869 (Lu, 1999). However, it was not until 69 years later that the technology was spread to Changsha, China.

Jan 1, 2019

By Weng Fu, James Vaughan, Stefan Lakemond

Uranium bearing copper sulphide flotation concentrates produced from iron oxide copper gold uranium (IOCG–U) ore contains radionuclides such as 238U, 230Th, 210Pb, 226Ra, 210Po, which have the potential to reduce their marketability, thus posing a challenge to the industry. Thus, a two–stage leach process has been proposed in this study. In first stage, a sulphuric acid leach process effectively dissolve most of the 238U and 230Th into solution, but other radionulclides (mainly 210Pb, 226Ra and 210Po) remain associated with copper sulphide minerals owing to their low solubilities in sulphuric acid solution. In the second leaching stage, the use of methanesulfonic acid (MSA, CH3SO3H) is investigated to selectively dissolve the 210Pb, 226Ra and 210Po from the residue of the first stage. The results indicate that 96% of 238U, 87% of 230Th, 90% of 210Pb, 86% of 226Ra and 17% of 210Po are dissolved using 3 mol/L MSA solution at 90°C for 3 hours, which represents a dramatic decrease in the radioactivity of the copper concentrate. INTRODUCTION Australia is host to one of the largest iron oxide copper–gold–uranium (IOCG–U) deposits in the world. Most of the value in these deposits is associated with copper. In mineral processing, the gangue minerals are separated from copper sulphide minerals that report to a copper flotation concentrate. However, due to the strong association of uranium with copper minerals and hematite, even clean copper concentrates can contain significant amounts of uranium (238U) and its radioactive decay elements, of which thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) are the long life radionuclides. These hazardous radionuclides negatively affect the marketability of the copper concentrates. Customer copper smelters in China, Japan and Europe may consider the radionuclides penalty elements or may not be able to process the feed. Therefore, there is a strong motivation to remove radionuclides from copper concentrates at the mine site before shipping to custom smelters in global market. Hydrometallurgical leaching has been widely employed to remove radionuclides from different kinds of minerals such as copper concentrates (Ragozzini & Sparrow, 1987), zircon concentrates (Aral, Sparrow, McDonald, & Norgate, 2007), and coal ash (Lei, Qi, Sun, Xu, & Wang, 2014). Leaching using sulphuric acid (H2SO4) solutions is the most widely used process for the extraction of uranium from uranium ores due to the relatively low cost and wide availability of the acid (Bhargava et al., 2015; Gilligan & Nikoloski, 2015). The leach process involves treating ground ore slurry with sulphuric acid at elevated temperatures (typically 60–90 °C) under oxidising conditions in order to convert the uranium in the minerals 2+ from the relatively insoluble tetravalent form (UO2) into water–soluble hexavalent state (UO2), which then complexes with SO42- and forms UO2(SO4)22- in solution. The uranium oxidation is generally carried out in the presence of ferric ion (Fe3+), regardless of the reagent and oxidant used. The most commonly used oxidants for uranium include sodium chlorate, pyrolusite and oxygen (Ring, 1980). These oxidants act indirectly by converting ferrous sulphate, formed by the oxidation reaction of UO2 in slurries, into ferric sulphate. The presence of Fe–containing gangue minerals such as hematite in the ore usually provides sufficient Fe required for the oxidation of UO2. After sulphuric acid leaching, the locked thorium (230Th), radium (226Ra), lead (210Pb), and polonium (210Po) elements are chemically liberated from hematite and uranium mineral grains (Ciobanu, Wade, Cook, Schmidt Mumm, & Giles, 2013). However, the extraction rate of radium (226Ra), lead (210Pb), and polonium (210Po) in sulphate solution is very low due to the limited solubilities of (Ra, Pb, Po)SO4 (Bagnall & Freeman, 1956; Liu & Papangelakis, 2006; Nikitin & Tolmachev, 1933).

Jan 1, 2019

By Karl Hoover, Cassandra Spence, Brent Bachewich, Jaakko Levanaho

"Since year 2000 the gold recovery into copper concentrate at Hudson Bay Mining and Smelting has reduced considerably during the summer months. This initiated a testwork program in the fall 2003 to find reasons and solutions for such change. During the testwork mineralogical factors, water quality effects and different reagents were evaluated. The reason for the lower recovery appeared to be the sensitivity of some collectors to pulp temperature. As a result of the work different collectors are being used in the mill in the summer than in the winter. A modification to the water system was also made to provide cooler water to the mill in the summer months.INTRODUCTIONHudson Bay Mining and Smelting (HBMS) is located in Northern Manitoba, just on the border of Manitoba and Saskatchewan. The complex consist of four different mines, Callinan, Trout Lake, Konuto Lake and 777 mine including copper smelter and zinc hydrometallurgical plants producing metallic copper and zinc. Gold is a very important byproduct providing about 30% of the mine revenue. In early 1990s when the company was facing declining ore reserves and was starting to gradually close down the operations, the 777’th exploration drill hole discovered a new orebody, which initiated a $0.5 billion expansion program. The main projects were a new 777 hoist with underground development and a new zinc cell house. About $30 million was used to increase the mill throughput to the present 2.27 million tonnes or 2.5 million short tons per year. The expansion programs were finished by the end of the year 2003.Historically the gold recovery at HBMS has varied between 60 and 70%. The recovery has been somewhat lower during the summer months. Gold recovery improvement projects were conducted throughout the 1990s, but were not focused on the seasonal gold recovery variance. However, since 2000, when the water system modifications to meet the increased water demand were completed, the gold recovery during the summer has been much lower than in the past. In August 2003 gold recovery fell below 30%, which initiated a metallurgical research program to discover the reasons behind the low gold recovery in the summer."

Jan 1, 2005

By W. D. Gould, A. Kapoor, K. Morin, P. Bédard

This paper presents the results of a research study that is being conducted by the Mine Effluents Program, Mining and Mineral Science Laboratory (MMSL), Natural Resources Canada aimed at evaluating biotechnology processes for the treatment of nitrogen compounds such as thiocyanide (CNS) and ammonia (NH4-N) which are present in gold mill effluents. A sequencing batch reactor (SBR) technology, commonly used for the biological treatment of municipal and industrial effluents, was used in this study. In the SBR process, the micro-organisms were able to degrade CNS to NH4-N and NH4-N to nitrate (NO3-N) at operating conditions of two 12 h treatment cycles per day, with pH maintained in the 7.4 to 7.6 range, and at room temperature (approximately 21°C) and also at 12 °C. The end products of CNS and NH4-N biological oxidation were NO3-N and sulphate (SO4) that are relatively non-toxic. Partial removal of NO3-N was achieved by biological denitrification reactions in the SBR process. The SBR process effluent was measured to be non-toxic to rainbow trout based on the 96 h acute toxicity test. The microbial consortium isolated from the SBR treating a simulated effluent was able to effectively oxidize CNS and NH4-N to NO3-N in water samples (under batch conditions) collected at three mine sites located in Quebec, the Northwest Territories, and Yukon.

Jan 1, 2004

By K. Bruce Hodgins

The North American mining industry faces challenging emissions regulations in coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable. Westport Innovations Inc., of Vancouver B.C. has developed high pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications, reduced emissions of NOx, PM, and CO2, with no loss in performance. This is accomplished through late-cycle high-pressure injection of natural gas directly into a diesel engine combustion chamber. The natural gas is injected at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the main natural gas fuel injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, low speed torque, high-power output, no engine knock and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored in a similar manner and volume to diesel fuel by virtue of its increased energy density over compressed natural gas. Cummins, Inc. of Columbus, Indiana and Westport have formed a joint venture, Cummins Westport Inc. (CWI), under which agreement the HPDI technology is being applied to a Cummins QSK engine series for high horsepower applications such as mine haul trucking. CWI, along with Komatsu Mining Systems, ENRG Fuels, Placer Dome, and Cortez Joint Venture are performing a feasibility study for the development and demonstration of an LNGfueled HPDI QSK engine in a large mine haul truck. The goal would be to demonstrate low emissions consistent with EPA ?Blue Sky? standards, high efficiency based on HPDI technology and good economics resulting from the high fuel consumption of 2,000+ hp trucks.

May 1, 2002

By M. C. Bétournay

Mine site infrastructure for storage and delivery of hydrogen must be standardized and acceptable for routine and safe industrial use before fuel cell technology is adopted as a major power source. An initial study reviewed possible options for production, storage and delivery of hydrogen for underground equipment. The high level review included assessment of economic, operational, technical, and health and safety risks. Following this review, a subsequent theoretical study to select typical minesite infrastructure and for construction at an operating research mine is outlined.

May 1, 2007

By Sunil Koppalkar, A. R. Laplante

"A Pilot Plant was installed in one of the grinding circuits of the Dome Mill, Ontario, Canada. Tests were conducted on a KCCD12 Knelson Concentrator to systematically analyze the effect of operating variables on the performance. The main objective of this test work was to explore the effect of very coarse (6 mm) feed size on GRG recovery and performance of the Knelson concentrator. Preliminary results have shown that coarse feed size is deleterious to maximizing recovery. Size-by-size GRG recoveries have shown an unusual trend in the sense that recoveries do not decrease monotonically with decreasing gold particle size. Similar trend observed in one other full-scale unit has been compared. The observed trend is probably linked to the feed size distribution and top size.INTRODUCTIONKnelson Concentrators are the most widely used semi-continues centrifuge gravity separation units for the recovery of gold and platinum group minerals (Xiao and Laplante 2004). The main advantages over the competing centrifugal gravity units are their design, operating simplicity and good separation efficiency that make them the most common choice for gravity circuit. Despite some characterization at bench scale and a limited characterization at full scale, there is a lack of a comprehensive study of impact of operating variables on efficiency that reflects realistic full scale operating practice. GRG characterization studies, at bench scale, on these units provide information about the occurrence of gold in ore samples but fail to provide adequate information about the effect of operating variables for full-scale units. It is well known fact that such work is difficult to undertake on full-scale units owing to the difficulties involved in sampling and systematic variation of operating parameters. To tackle these problems, a pilot facility consisting of a 12-in CD Knelson Concentrator, a feed screen and tailing pump was installed in one of the grinding circuits of Dome Mill. This paper describes the work carried out and the results.Porcupine Joint Venture (PJV)Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. The JV utilizes the milling capacity of the Dome Mill to process ore from Placer Dome and Kinross mines. The Dome Mill circuit has gravity concentration, cyanidation and CIP circuits to recover gold. Gravity recovery has been used at Dome Mill since inception to recover gold: first by using conventional jigs, which were eventually replaced by two Knelson Concentrators in 1993, one in each of the grinding circuits. Three more Knelsons joined the circuit in 2002 to improve gravity recovery. An Acacia Intensive Leach Reactor was also added in 2002 to process gold concentrates replacing shaking tables (Chong et al 2004)."

Jan 1, 2007

By S. Felderhof, W. S. Vaughan

"Over the years, it has been increasingly difficult for the minerals industry to raise the necessary capital for its activities. To alleviate this phenomenon, complete transparency and capital market efficiency is needed. Since a company’s mineral resources and mineral reserves base is an essential component to obtaining capital, reporting these assets must also be transparent and efficient. This must occur, however, at an international level given that mineral industry operations, and its financing, are international. To achieve this, an international committee (i.e. Australia, Canada, South Africa, the United Kingdom and Europe, and the United States) was formed and has been developing standards for the reporting of mineral resources and mineral reserves.The effectiveness of these standards, however, depends on adoption by the required regulators. Unfortunately, these standards have not been recognized by the U.S. Securities and Exchange Commission (SEC). Instead, the SEC adheres to its old standard (Industry Guide 7), making it increasingly expensive and difficult for international mining companies to obtain capital in the United States. Compounding the problem is the SEC’s influence over the current work of the International Accounting Standards Board and the International Organization Organization of Securities Commissions. These organizations are in the process of standardizing international accounting practices and international securities rules and regulations. Their current position may prevent adoption of the industry-developed mineral resources and mineral reserves standards which are internationally recognized."

Jan 1, 2005

By U. Olsson, M. Ramström

"The IREDES1 Special Interest Group (SIG) for drill rigs has been active since its launch during MineExpo 2000 in Las Vegas, Nevada, United States. SIG for drill rigs is responsible for the development of an IREDES drill rig profile, including the exchange of production planning, performance, and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During 2001, a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies, and third-party suppliers and reviewed during several SIG meetings. The profile for prototyping projects was released in mid-2002; the first official IREDES release was based on feedback received from these projects.In 2002, LKAB and Atlas Copco decided to carry out an IREDES prototyping project using the Simba L6C production drill rig. The goal was to verify the drill rig profile and identify potential problems prior to the official release. This was done by implementing the IREDES prototype version into LKAB’s production planning and Simba rig control systems. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this, the mine production system was adapted for drill plan export and logging data import in IREDES format.This paper presents the most recent results of the IREDES prototyping project. Results from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES, will be a central requirement for future mine automation.As a result of the IREDES prototyping project, the IREDES standard was approved at the IREDES board meeting held at the 2003 CIM Annual Conference and Exhibition. Soon thereafter, IREDES compliant products, including drill rigs and mine production planning systems, were put on the market."

Jan 1, 2005

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019