Search Documents

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,' there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin' in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin's Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier' were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6'Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By F. H. Gilpin

SINCE Noah pitched his ark within and without with pitch, the use of asphalt in human endeavor has been increasing-for Noah's pitch was asphalt. Asphalt is a bituminous material found in nature, either pure or admixed with smaller or greater quanti-ties of mineral and non-mineral materials, or obtained by the refining of crude asphaltic-base petroleum under proper methods of control. Native or "natural" asphalts are scattered through-out the world, though the commercial value of the various deposits varies greatly, depending upon both their accessibility and magnitude and the quality of the material found. It is an acknowledged fact that such asphalts have been produced through natural causes by practically the same application of tempera-ture and pressure as are used in the modern refining of crude asphaltic-base petroleum. The best known of all the native asphalt deposits are those of Trinidad Lake in the Island of Trinidad, British West Indies, and of Bermudez Lake in Vene-zuela. Asphalt from Trinidad Lake, after refining to remove organic and some inorganic diluents, contains approximately 35 per cent, of inorganic residue, and the asphalt thus produced must be fluxed with lighter asphaltic or semi-asphaltic base oil to make it com-mercially utilizable. The refined asphalt obtained from the Bermudez Lake deposit contains from 4 to 6 per cent. of inorganic material which cannot be removed. This asphalt, also, must be fluxed to produce com-mercial products. Small quantities of similar materials are available in other locations. The best pure native asphalt' is known as. gilsonite and is mined in com-mercial quantities in the State of Utah. In numerous places in the United States, particularly Oklahoma and Kentucky, there are deposits of sand¬stone and limestone impregnated with bitumen, which are known as rock asphalts. These rock asphalts may be used, particularly in the paving industry, either as found or by slight fluxing; from some deposits the asphalt is extracted and marketed commercially.

Jan 2, 1923

By R. C. FLEMING

G OLD MINING is enjoying a real revival in the West, and a considerable portion of the production is coming from small properties. The large mining companies of the world get most of the publicity, but in the last year the small gold property has often proved a more attractive field for the mining engineer looking for something to do. Old mines have been re- opened, prospects have been more closely examined, and many properties that were out of the running with the high commodity and labor costs of two or three years ago, have recently been making money for their operators. An interesting phase of this activity is the operation of so-called one-man mines. The west is dotted with these small properties, without the resources or reserves to warrant large-scale operation, but which return a living and often something over to one or two men who under- stand mining and simple methods of treatment.

Jan 1, 1932

By H. Conrad, V. V. Damiano, G. J. London

A method is described for producing single crystals of high-purity beryllium, Be-4.37pct Cu, and Be-5.24 pct Ni. These crystals were prepared for testing in compression parallel to the [0001] by orienting and lapping to within ±3' of arc of the (0001). Microstrain testing apparatus is described along with c axis compression results for ingot purity beryllium, twelve-zone-pass material, and the above-mentioned alloys. Results show no measurable plasticity for the ingot purity material from -196" to 400°C, although some surface traces of (1122) slip was observed at 200°C and above. The twelve-zone-pass material shows substantial microstrain plasticity at 220°C with slip on (1122). Both alloys show significant plasticity at room temperature and above with slip also on (1122) planes. THE two slip systems which normally operate during the plastic deformation of beryllium in the vicinity of room temperature are:' basal slip (0001)(1120) and prism slip . Pyramidal slip with a vector inclined to the basal plane has been reported for elevated temperatures,'-a but occurs near room temperature only at very high stresses.~ A summary of the available data on the effect of temperature on the critical resolved shear stress for slip on these systems has been compiled by Conrad and Perlmutter.~ It has been postulated6'7 that one of the principal factors contributing to the brittleness of poly crystalline beryllium at temperatures below about 200°C is the difficulty of operating pyramidal slip with a vector inclined to the basal plane. Hence, detailed information on the operation of such a slip system is important to understanding the brittleness of beryllium. The operation of pyramidal slip with a vector inclined to the basal plane is best accomplished in beryllium by compressing single crystals in a direction parallel to the c axis. In such a test the resolved macroscopic shear strzss on the basal and prism planes is zero and (1012) twinning which is favored by tension along the c axis does not occur. Hence, in c axis compression of beryllium the normal deformation modes are inhibited and the operation of pyramidal slip with a vector inclined to the basal plane is favored. In the present investigation, c axis compression tests were performed on beryllium single crystal as a function of temperature (77" to 700°K), purity (commercial and twelve zone pass), and alloy content (4.37 wt pct Cu and 5.24 wt pct Ni). Presented here is a description of the test techniques employed and the gross mechanical behavior observed. A detailed analysis of the slip traces developed on the surfaces of the deformed specimens during these tests and the results of electron transmission studies of the deformed crystals are given in a separate paper.B PROCEDURE 1) Materials and Preparation. Single crystals about 1 in. diam were prepared of the following materials: commercial-purity beryllium, high-purity beryllium, and two beryllium alloys, one with 4.37 wt pct Cu and the other with 5.24 wt pct Ni. The commercial-purity single crystals were obtained by cutting specimens from large-grained ingot of Pechiney SR material, which is approximately 99.98 pct pure. The high-purity crystals were prepared by floating-zone refining (twelve passes) a rod (7 in. by 1 in, diam) of Pechiney SR grade cast and extruded beryllium. Although an absolute chemical analysis of the zone-refined material was not established, mass spectro-graphic analysis, emission spectrographic analysis, and y activation analysis indicated that it contained in atomic fractions about 5 to 10 ppm each of carbon and oxygen, 1 to 5 ppm each of nickel and iron, and about 1 to 2 ppm of copper, with the remaining residual impurities being less than 1 ppm. Further indication of the purity of this material is provided by the critical resolved shear stress for basal slip, which was approximately 300 psi. The starting material for the alloy single crystals was 1-in.-diam floating-zone-refined (six passes) rod of Pechiney SR grade beryllium. Two such rods were wrapped respectively with sufficient weight of wire of high-purity copper (99.999 pct) or nickel (99.999 pct) to yield a 5 wt pct alloy. A seventh floating-zone pass was then applied to each of the rods to accomplish the initial alloying and an eighth pass for homogenization. Analytical samples were taken from regions of the rod immediately adjacent to where the mechanical test specimens were cut; these indicated 4.37 wt pct Cu and 5.24 wt pct Ni. 2) Crystal Orientation. To avoid the occurrence of basal slip during c axis compression testing, it is necessary to load the crystals as nearly parallel to the c axis as possible. Preliminary c axis compression tests indicated that plastic flow and/or fracture occurred at stresses of the order of 300,000 psi; hence on the basis of a critical resolved shear stress for basal slip of 300 to 400 psi, the maximum crystal misorientation permitted is about 4 to 5' of arc. Since this accuracy cannot be obtained using the usual back-

Jan 1, 1969

By K. G. Davis, P. Fryzuk

WEINBERG,' in an investigation of solute distributions along unidirectionally solidified rods of dilute silver in tin alloys, concluded that, for rods of 2 mm diameter or larger, a very high degree of convective mixing takes place in the melt ahead of the advancing interface. Suggested causes for this mixing were (1) thermal convection, (2) convective currents set up by changes in fluid density associated with concentration gradients, and (3) currents set up by changes in volume during freezing. Evidence was presented that causes (2) and (3) were not primarily responsible for solute mixing. Further, convective mixing took place in horizontal rods with temperature gradients as low as 6°C per cm, putting doubt on the importance of thermal convection. In the present work, convective mixing is examined in melts with known initial solute distributions. The absence of a moving solid-liquid interface eliminates convection caused by volume changes on solidification. In the first experiment, three silica tubes 2 mm in diameter and approximately 20 cm long were filled with an alloy of 100 ppm Ag in tin (99.999 pct purity), placed adjacent to one another in a horizontal furnace, and solidified from one end at 1 cm per hr. A110, a Y emitter, was used as tracer. A few centimeters at the start of the rod were left un-melted, to determine the initial concentration Go. After solidification was complete, one sample was removed. The hot furnace was then brought back to

Jan 1, 1965

By P. H. Dudley

THE piping and segregation of ingots of steel is a comprehensive subject, and must be studied in reference to the different grades of soft, medium, and hard steel, rather than to discuss it in a general manner, as though applicable to all grades. Rail steel, however, will receive the most consideration in this paper, for the wheel-loads of the motive pourer and rolling stock have doubled from 1890 to 1910. Steel rails and tires which were efficient under the light loads, became less serviceable under the double wheel-loads, quadrupled tonnage, and higher speeds. Bessemer Steel. Bessemer steel of froth 0.10 to 0.15 per cent. of carbon, for splice-bars, spikes, and tie-plates, rises in setting, and is cast in bottle-mouthed molds, which must be capped to prevent an over-flow from the top. This grade of steel rises in the molds and makes a longer ingot than the volume of molten steel when first teemed. The ingots which are allowed to cool and then cut open, show, particularly in the upper part, large occluded blow-holes, and when they are Dot oxidized or do not contain foreign matter, weld more or less completely when the steel is rolled or forged above 1,100° C., and it :is in this way that the blow-holes are closed it the low-carbon steels.

Jan 4, 1913

By Henry F. Cooper, Scott E. Blouin

Large jacking test procedures that have been applied to obtain static in-situ rock properties (Ref. 1) have shown that the in-situ rock modulus and strength can be considerably less than what would be obtained from laboratory tests on intact samples. This trend is also expected to be true for dynamic properties, but few dynamic in- situ rock property tests have been conducted. During the past several years, high explosive test procedures have been developed to simulate the airblast and direct induced ground motions (Ref. 2) produced by nuclear explosions . These test procedures load large volumes (up to 10 7 f t3) of the earth with stress levels sufficiently high to produc5 feet of particle displacement over surface areas up to l0 5 ft2. This paper discusses some of the data obtained, and the implications of these results for our understanding of the dynamic response of in-situ rock. DESCRIPTION OF TEST PROCEDURES As shown in Fig. 1, the High Explosive Simulation Technique (HEST) consists of a cavity of uniform height bounded on the sides by a soil berm, above by an overburden of uniform thickness, and below by the test bed on the earth's surface. Horizontal racks of detonating cord are placed in the cavity and detonated at one end of the test bed. This detonation produces an explosive wave that propagates across the test bed, loading the earth with an overpressure pulse that decays with time because of the compression and lifting of the overburden. Since 1964, there have been approximately 40 such tests on test bed areas ranging from a few hundred to l0 5 sq ft., simulating peak overpressure conditions between about 100 and 6000 psi and specific impulses between a few and over 100 psi-sec.

Jan 1, 1971

By R. H. Hiltz, R. W. Douglass

Large-grain specimens of iodide titanium prepared metal-lographically were stain etched using the technique of New York University as modified by Watertown Arsenal Laboratories. Orientations of grains showing an abnormal response to stain etching were determined by back-reflection X-ray techniques. X-ray results showed that a-titanium grains, oriented such that their basal planes were parallel to the polished surface, have a slower reactivity to stain etching than any other orientation. Grains oriented such that their basal planes made small angles with the polished surface exhibited reaction rates between that of the true basal orientation and the normal rate. As the angle with the surface increases the reactivity increases up to a maximum angle of 14 deg. Basal planes making an angle with the surface of greater than 14 deg show normal reactivity to stain etching. These data, plus work on polycrystalline specimens, indicate that the oxidation rate of titanium might be reduced by correct alignment of crystal planes. ThE earliest observed phenomenon in the micrography of titanium was the occurrence of a grains which exhibited no birefringency. Even though a titanium possesses a hexagonal-close-packed structure and should be optically anisotropic, it can appear optically isotropic, when the crystal is so oriented that its intersection with the polished surface is perpendicular to the axis of symmetry. During the develoment of color staining techniques for titanium: it was noted that the a phase did not stain uniformly. Staining of specimens of commercially pure titanium resulted in a micro-structure of blue-colored grains, among which were randomly oriented a few grains exhibiting colors between the initial yellow and the final blue color. Under polarized light, these off-colored grains appeared to be optically isotropic. More intense study with polarized light, however, showed only the yellow grains to be isotropic. The intermediate colored grains exhibited weak birefringency, which at first glance is not detectable due to the strong birefringency of the surrounding structure. Aminoff2 and Straumanis3 have previously shown that in zinc the basal orientation is less reactive than other orientations. Leidheiser4 showed the same thing to be true for the hexagonal-close -packed configuration of cobalt. Thus, it would appear that the basal-plane orientation is responsible for the abnormality in stained titanium. Later work by Leidheiser5 on cobalt has shown that other planes besides the basal plane exhibited reaction rates slower than the normal rate. Reported planes were the (100), the (1011) and several planes making small angles with the basal plane. The last observance appears not to be due to the reactivity of the reported plane but due to the reactivity of the basal plane which is very close to being parallel to the surface. There are, then, two possible explanations for the range of colors observed in stain-etched a titanium. Since extensive research on the effect of orientation on surface reaction has failed to provide any definite trend, these two explanations are not adequate in themselves. Planes showing the retarded reactivity differ not only for different crystal structures but for metals of the same crystal structure and even for different reactions of the same metal. Tragert,6 Leidheiser,7 Tammann,6 and wagner9 have shown copper to exhibit retarded reactivity on the (111) plane. However, Leidheiser10 has shown that under other conditions the retarded reactivity of copper is associated with the (100)

Jan 1, 1960

By A. A. Smith, J. S. Smart

THE elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses, When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range 0 to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorily determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing and oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B. and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold, The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300° and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type, All samples were quenched from the annealing temperature in 10 per cent H2SO4 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.1 EFFECT OF SILVER Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

C. W. MERRILL*—Mr. Hughes' paper not only is very well presented but is most timely in that it covers a subject of vital interest to the United States. Tin is one of the strategic metals which has not been found here in appreciable quantities. The total United States tin output since the first recorded production over 100 years ago would not supply current consumption for a fortnight. On the consumption side, tin is extremely important in national defense because of its use in tin plate which, in the form of tin cans, makes it possible to feed properly the armies that the United States recruits from its civilian population in emergencies. Moreover, the internal combustion engines so important in powering tanks, planes, and other war machines, require large quantities of tin alloys for bearings and for soldering. These considerations, along with the fact that Malaya, historically, has been the leading source of tin to the United States, make the kind of information that Mr. Hughes has presented so ably. a matter of vital interest. Your Chairman, Mr. Romanowitz, in his introduction, referred to the fact that I had been a member of the United States delegations to the three meetings of the International Tin Study Group. Some comments on the Group's objectives and deliberations may be of interest. When it appeared that the International Tin Committee, the prewar producer's cartel, might soon revive its operations and extend its control agreement beyond the expiration date of Dec. 31, 1946, the United States Government became interested in some kind of an international trade organization concerned with tin which would give the consumers' interest equal representation with the producers' interests. An international meeting was called in London in October 1946 to consider this problem. I did not attend that meeting hut the result of the meeting was the organization of the International 'Tin Study Group which

Jan 1, 1950

By R. J. Lytle, E. F. Laine

The in situ high frequency electrical conductivity and permittivity of Colorado oil shale were recently measured. The measurements were made at 45 MHz (45 million cps) by transmitting from one borehole to two receiving boreholes, all boreholes in line. A differential measurement using the received signals was used to calculate the conductivity and permittivity.

Jan 1, 1983

By Charles O. Burgess

The improvement in the quality of cast iron by means of alloy additions has been a metallurgical accomplishment of recent years. Work in this field has shown that chromium is one of the most effective of such additions but, in general, the influence of chromium has been studied only in connection with other alloying additions, with irons other than foundry irons, or with relatively high percentages of chromium. The present study was initiated for the purpose of determining the influence of small additions of chromium (0.25 to 1.00 per cent) on the quality and resultant properties of cast irons of various foundry grades. The effect of small chromium additions on cast iron was investigated with particular reference to casting characteristics, hardness vs. section, strength, machinability, heat resistance and structure. Material Tested Three separate types of cast iron were investigated as to the effect of small chromium additions. The first series of these irons was prepared from remelted foundry cast iron at the Union Carbide and Carbon Research Laboratories, and the other two series consisted of cupola melts made under usual operating conditions. The first series was made by melting 30-lb. charges of foundry scrap iron containing 2.86 per cent carbon, 2.72 silicon, 0.50 manganese, 0.062 sulfur and 0.794 phosphorus in a carbon resistance furnace. The chromium was added as high-carbon ferrochrome just before pouring. The irons were cast at approximately 1250" C. (2282" F.). The analysis and physical properties of these irons are given in Table 1, test 1. The second set of cast irons was made in a cupola in accordance with normal practice, the charge containing approximately 42 per cent steel scrap and the chromium additions being made to the ladle. Analysis and tests of these heats are shown in Table 1, test 2. A small amount of copper was present in heat C of this series. Further data on the effect of chromium on strength were obtained from a third series of 13 cupola heats containing from 0.06 to 0.50 per cent chromium and made without steel additions. The heats were all

Jan 1, 1933

By AIME AIME

IN an address before the New York Section. A.I.M.E., Oct. 20, Alex L. ter Braake, speaking on the tin industry of the Netherlands East Indies, interjected a few remarks, at the chairman's request. on the mineral stock-piling project now before Congress in a bill sponsored by Senator Scrugham. The full text of Mr. ter Braake's paper was published in the Nov. 6 issue of the American Metal Market. Following mention of the buffer stock scheme as applied in the tin industry, Mr. ter Braake continued:

Jan 1, 1943

By E. A. Gulbransen, K. F. Andrew

THIS paper. will present the results of our studies on the kinetics of the gas phase reactions of co-lumbium and tantalum with O2, N2 and H2. Studies on zirconium and titanium have been previously reported.9,11 Due to their high melting points and their many excellent physical and chemical properties, colurn-bium and tantalum have been finding their places as useful metals in science and industry. Chemically the metals are very inert to gas and liquid phase corrosion at room temperature. However, at moderate temperatures of 250°C and higher the metals react readily with oxygen and hydrogen. It is of interest to study the gas phase reactions of these metals for the following reasons: (1) to compare the rates of the several reactions with those of other metals and to correlate the rate data with theory and structure predictions, (2) to add basic information on the practical difficulties of the reduction, refining and working of columbium and tantalum, (3) to anticipate new uses for the metals and (4) to understand the role that the metals play as components in high temperature alloys. Literature Survey A number of papers exist in the literature on the gas phase reactions of columbium and tantalum with O2, N2 and H2; however, only fragmentary data have been reported on the kinetics of these reactions. Although the free energy of formation of the oxide Ta2O520at 25°C has been determined and some thermodynamic work has been reported on columbium and its oxides, the data are not sufficient to make equilibria calculations at elevated temperatures. Oxidation: 1. Kinetics: The rate of oxidation of columbium and tantalum has been studied by McAdam and Geil23 using the interference color method. Tantalum is reported to oxidize more slowly than columbium, zirconium and iron. The amounts of oxidation of columbium after 20 hr in air for several temperatures are reported by the Fansteel Metallurgical Corporation.36 Columbium starts to oxidize in air at about 200°C. The oxide is said to be adherent and prevents further oxidation until the temperature is raised. Columbium is reported not to become brittle on heating in air for short periods like tantalum because the oxide film prevents further reaction. The columbium oxides dissolve into the metal when heated in a vacuum at temperatures between red heat and 1200°C. Above 1200°C the oxides are reported to evaporate. Columbium, in the oxide free state, is an active getter in vacuum tubes. 2. Preparation and Structure: G. Grube, O. Kuba-schewski and K. Zwiauer15 have studied the decomposition of Cb2O5 in argon. They find that CbO2 is formed slowly at 1150° and rapidly at 1300°C. Cb2O5 can be reduced to CbO2 by moist H2. The reduction of this dioxide to the lower oxides is rapid. By varying conditions CbO2, Cb2O3, CbO and Cb2O can be formed. CbO2, CbO and Cb2O have independent lattices while Cb2O3 is a stoichiometric mixture of CbO and CbO2. In a later paper O. Kuba-schewski" has shown that CbO is cubic and that CbO2 has a rutile type of lattice. The most exhaustive work on the oxides of columbium is that of G. Brauer.8 The number and constitution of the solid phases in the binary system Cb-O were investigated by the preparative, analytical and X ray methods. He indicates that only the oxides Cb2O5, CbO2 and CbO exist with limited regions of homogeneity. The solid oxide Cb,O, exists

Jan 1, 1951

By P. G. Winchell, J. K. Jackson

The strtcture of body-centered Fe-Ni-C alloys (0 to 16.5 wt pct Ni) containing less than 0.015 wt pct C was investigated by measuring the carbon-diffusion peak at low frequencies with a torsion pendulurrr. By determining the Snoek damping in ferrite and in quenched alloys of identical composition, the effects of nickel content and heat treatment were separated, and the existence of a structure in which Snoek damping is greatly reduced was revealed in the quenched ternary alloys. The relative amount of this structure increases with increased nickel content and cooling rate. It is proposed that this structure may be highly imperfect or tetragonal. In Fe-Ni-C alloys containing only ferrite the addition of nickel (0 to 5.1 wt pet) decreases tke area of the carbon-diffusion peak and shifts its position to lower temperatures but broadens the peak only slightljl. The decrease in peak area with increasing nickel implies that short-range interactions with the nickel atoms prevent some of the carbon atoms from participating in the relaxation process. The shift in the peak position indicates a long-range effect of nickel on the movement of carbon atoms so that at 300°K the diffisivity of carbon in -ferrite is increased by about 35 pct by the addition of 5.1 tut pct Ni. The results are presented as distributions of relaxation strength 072 the activation energy under the assumption that the frequency factor is invariant. BODY-CENTERED iron-base solid solutions dissolve carbon interstitially in the octahedral sites. The occupation of an octahedral site produces a tetragonal distortion of the surrounding lattice. These sites fall into three sets according to the orientation of the tegragonal distortion associated with each and may be identified by their lattice coordinates as: type 1/2 0 0, type 0 1/2 0, type 0 0 1/2. At low carbon levels in cubic ferrite the carbon atoms are distributed at random1 among these sites. In high-carbon body-centered iron-base solid solutions, which are unstable with respect to several two-phase mixtures, a tetragonal structure occurs as the product of the diffusionless transformation of austenite. This transformation is commonly accompanied by appreciable microstrain and its product is called martensite. The tetragonality of martensite, a supersaturated solution of carbon in a iron, is maintained prior to decomposition even though local diffusion of carbon occurs as evidenced by carbide precipitation. The tetragonality is taken as evidence that one set of octahedral sites is preferentially occupied by carbon. (This preferential occupation is called ordering below.) Support for this view is presented by the absence of strain-induced carbon-atom diffusion in high-carbon solid solutions (martensite). Such diffusion occurs in ferrite and produces the 40°C internal-friction peak observed at 1 cps frequencies.' Thus, there appears to be qualitative evidence favoring the view that at sufficiently high carbon levels tetragonality arises spontaneously as a result of the ordering of the carbon atoms; however, no experimental evidence exists concerning an equilibrium between cubic and tetragonal body-centered solid solutions. Moreover, attempts to estimate the energy of ordering7-' predict a value too low to maintain the tetragonality observed at medium carbon levels, 0.3 to 0.6 wt pct C. In the present work an attempt using internal-friction measurements is made to establish the presence or absence of tetragonality in low-carbon body-centered solid solutions formed by quenching austenite. Fe-Ni alloys containing about 0.01 wt pct and 0 to 15 wt pct Ni were selected for the study. While the work was in progress Gilbert and Owen10 reported that the transformation which occurs in these alloys during quenching at rates up to 5000°C per sec is not martensitic but is more properly categorized as massive. Thus, the solid solution

Jan 1, 1964

By T. F. Archbold, P. G. McCormick

Silica fiber 11arkevs and hardness irzdentatiozs have been used to study the thermal diffusion of racancies in zinc placed in temperature gradients of 460o and 706oK per Cm All markers mored toward the higher temperatures, and the data show that the heat of trarlsport Q is greater than the eizthalpy of z,acancj3 forrjalion E by an amount equal to 3.5 kcal per mole. These results ore not in agreement with those obtained in either of the two previous studies with zinc. The problem is discussed in terms of experimental differences and racancy source and sink efficiencies. THE general interest in thermal-diffusion phenomena over the past several years has prompted a number of marker movement studies using pure metals. In order to understand better the relationships between thermal and mass flow, a general goal of the experiments has been to obtain values for the net enthalpies carried by the diffusing atoms. For self-diffusion by means of the vacancy mechanism, the determination of relative marker positions before and after an anneal in a temperature gradient permits a calculation of a value for (Q - Ef). Q is the transferred enthalpy, and Ef is the enthalpy of vacancy formation in the metal being investigated. The initial experimental study of thermal diffusion in pure metals was accomplished by Shewmon who found essentially no movement of surface-hardness indentation markers in single and bicrystals of zinc held for 20 days in a temperature gradient of 310°C per

Jan 1, 1967

By C. A. Heiland, W. H. Courtier

The investigations described were made on a portion of Clear Creek basin near Golden, Colo. (-4 portion of the area under survey is shown in Fig. 1. The photograph was taken in the vicinity of station No. 2 of Line 11.) Three principal purposes were in the minds of the investigators: 1. To repeat with modern, more sensitive and more reliable instruments magnetometric placer investigations previously made. 2. To disprove the recently advanced theory that deposits of the glacial period have no pronounced magnetic effects. 3. To develop in detail the theory of the magnetic effects produced by placer deposits. Six years ago, the first magnetic observations were published, which proved that it is possible to locate gold-bearing channels with relatively crude instruments.' Two years ago, K. C. Laylander published results obtained with similar instruments.2 The measurements of the latter were discussed by the senior author of this paper.3 At that time, however, the material available for such a discussion was somewhat scarce and not made with the most modern magnetic instruments, although very brilliant results were obtained. Therefore, the senior author felt that magnetic investigations should be made on very clear geologic conditions with the most modern instruments. Comparison of Magnetometers The junior author undertook this work in the spring of 1928. The magnetic field balances, for vertical and horizontal intensities, designed by Schmidt were used (Figs. 2 and 3). The scale value of these instruments was approximately 257 and 157, respectively. The middle

Jan 1, 1929

By R. C. Allen

ABOUT four years ago the writer proposed a revision of the correlation of the Huronian formations in Michigan, and noted the bearing of the question on the correlations of the Huronian rocks in Wisconsin and Minnesota.1 Dr. C. K. Leith opposed this revision and argued for the retention of the correlations of the United States Geological Survey, published in 1911,2 for which he and Dr. Van Hise were mainly responsible. As late as June, 1917, Harder and Johnson, following Leith, thought it "premature to change radically a correlation based on years of careful field work."3 The work of Wolff on the Mesabi and Cuyuna Ranges, of Hotchkiss on the Gogebic Range (unpublished), and of the writer and assistants on the Michigan ranges, together with data developed by exploratory and mining operations, has introduced so many pew facts not recognized in the scheme of the U. S. Geological Survey that the correlations of 1911 must be considered, in some important respects, obsolete. Indeed new data are accumulating so rapidly that any classification, which for the moment may seem best to explain the facts, is almost immediately modified or refined by further observations. The problem of Huronian correlations is difficult, but interesting and important. With the aid of fossils, stratigraphers of the post-Algonkian formations have been able to show that slight disconformities may separate strata of vastly different ages, and that within physically conformable strata may be concealed a hiatus of great magnitude. In the non-fossiliferous Huronian group, minor physical breaks in the strata are

Jan 9, 1919

By A. Singh, W. M. Fleming, J. J. Santana, A. E. Torma

The present study investigated the extraction of uranium from a low-grade ore by sulfuric acid and the removal of radium from the leach residues by brine solutions. The optimum leaching conditions were found to be 1.5 mole [£]-1 H2SO4, 6.Og[9]-1NaClO3, 75°C,50% pulp density and 750 rpm with respect to the rate of uranium extraction. The maximum theoretical attainable rate of uranium extraction was determined to be V = 1.09 x 10 -2 mole [¢]-1h-1 with respect to pulp density. The order of reaction was found to be zero regarding the effect of sodium chlorate concentrations. The apparent activation energy of uranium extraction was calculated from the Arrhenius plot to be [A]E a - 2.36 kcal mole-1 (9.87 kJ mole-1). Based on a statistical design, an empirical equation has been developed describing the rate of uranium extraction with the leaching parameters. This equation can be used to generate data which may be useful for scaling up the process to pilot plant level. The most efficient brine solution for the extraction of radium - 226 from the leach residue was found to contain one mole[f] -1 CaCl2 and 0.01 mole [2] -1 HC1. The two step leaching with this solution resulted 87% removal of radium from the leach residue. On the basis of this study, a flow-sheet has been proposed for the extraction of uranium and radionuclides from the ore and leach residue to yield almost innocuous tailings.

Jan 1, 1982

By L. W. McKeehan, W. C. Elmore

The magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined1, "or investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter2 first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators:' have used Bitter's original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement ill the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel5 single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. Specimens The following list describes the specimens used in the present investigation. Designation Description A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which lie gave the following typical analysis: C, 0.05; P, 0.038; S, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick. By X-ray analysis angles between disk normal and [100] 75o, [0101 76" [00l] 21o. A2 Same as A1 except: diameter 0.75 cm. A, Same as A1 except: diameter 0.68 cm.

Jan 1, 1936