Search Documents

By Z. Y. Hu

This paper reviews the past and presents the present state of industrial minerals in China. The resources, reserve and production of major non-metallic minerals are given. The mining and milling operations are reviewed. The future development and plans of Chinese non-metallic minerals industry are summarized.

Jan 1, 1990

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By T. J. Fronapfel

Impacts to ground water from mining are being comprehensively regulated in Nevada through specific requirements for design, construction, operation, permitting and closure. This program is the nation's most comprehensive for control of activities at mining operations which have the potential to cause groundwater degradation. It encompasses virtually all types of facilities, including placer, physical separation, flotation, testing, leaching and milling. Minimum design requirements are established by regulation, and must be met by each facility. Site-specific monitoring requirements are established for each facility, and are heavily emphasized. Regulatory and technical requirements and relevant permit conditions are presented and discussed.

Jan 1, 1992

By C. C. Harvey

Based on resource studies in many developing countries, four categories of industrial clay resources are recognized as precursors to development strategies. Category I: High quality, high technology clays requiring major investment for large tonnage international markets. Category 2: Unique specialty clays requiring advanced technologies for small tonnage niche markets. Category 3: Lower technology, moderate quality clays, predominantly to supply local markets. Category 4: Low quality clays requiring little or no processing. Projects with Categories 1 and 2 clays require extended development times (green field to investment decisions) with significant pre-development investment, while projects with Categories 3 and 4 clays require shorter development timetables and lower levels of investment.

Jan 1, 1998

By R. V. Ramani

In 1970, of the 603 million tons of coal produced in the United States, 339 million tons, or 56%, were produced by under- ground mines. While the ratio of underground to surface production has been decreasing in the last few years, it is anticipated that a 60:40 ratio of underground to surface-mined coal will remain for some time. Underground coal operators are continuing to invest in new mines and are interested in increasing the efficiency of all their operations. One area for improvement is in mine planning and design, particularly in the area of selection of equipment for operation. Because of the availability of a wide variety of equipment, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, such a choice must be made on the basis of technological facts and forecasts related to the mining operation. If the mining conditions can be reasonably predicted, along with a mining plan, it should be possible to insure the selection of the right equipment for the particular application. In order to increase the efficiency of underground coal operations, it is necessary to understand not only the operating system in detail, but the inter-relationships between system components and the operating environment. With such an understanding comes the application of simulation and other operations research techniques to plan and operate mining systems. Computer simulation studies have been successfully adapted to underground coal mining, and applications by Prelaz et al. (1965), and Manula and Sanford (1969) are some that are being used by the mining companies. However, a need still exists for better understanding of certain intra-system and system-environment interactions in order that computer simulation programs may be provided with better input data for more effective application. This paper deals with one aspect of the coal-winning system in need of better definition, namely, studying the performance of continuous miners.

Jan 1, 1973

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By J. J. Wallaert

The decreasing supplies of natural gas and low-sulfur crude oil available for electric power generation in the United States will unquestionably shift the emphasis to nuclear and coal fired steam power plants in the immediate future. Failure to do so will ensure our dependence on mid-east low sulfur crude oil comprising some 70% of the known world reserves, and imported liquid natural gas. By contrast, the United States has 43% of the known world reserves of anthracite, bituminous and semi-bituminous coal and 48% of all known coal reserves of the world including lignite. It is evident, therefore, that coal is alive and well and will continue to be a significant energy source for the production of electricity for many years. Of course, concern for our environment and the development of new technologies will ultimately curtail the utilization of coal for the generation of bulk power, but information released by the National Electric Reliability Council and the Federal Power Commission is worth repeating. In the year 1972 the total capacity of generating units in the United States was 379,552 Mw of which 149,974 Mw, or 39.5% of the total, was produced by coal fired steam turbines which consumed 344,700,000 tons of coal. New capacity additions planned or in construction show that in the year 1981 our total generating capacity will be 843,503 Mw, of which 257,995 Mw, or 30.6% of the total, if from coal only. Translating this increase into terms meaningful to the bulk material handling industry suggests that ten years from now the utility industry will require 590,000,000 tons of coal per year - a monumental task - if we are to sustain our current demand rate for power.

Jan 1, 1973

By Robert S. Holmes

The U. S. Army Corps of Engineers Explosive Excavation Research Office (EERO) of Livermore, California, has been engaged in research and development of excavation techniques using both nuclear and conventional explosives since 1962. Prior to July 1971, this organization was designated the U. S. Army Corps of Engineers Nuclear Cratering Group. The EERO mission is performed as part of the joint Atomic Energy Commission -Corps of Engineers nuclear excavation research pro-gram. During the period 1962-1969, the Corps executed many cratering explosions using spherical charges of up to 85 tons of nitromethane to model nuclear excavation concepts and to develop design criteria for the nuclear cratering explosions. The experience gained in these modeling tests suggested that explosive excavation using large chemical explosive charges could be applied to excavation projects as an economical substitute for traditional excavation techniques. Consequently, the Corps' research program was broadened in 1969 to include development of chemical explosive excavation as a construction tool. The term "explosive excavation" denotes the use of large buried explosive charges to produce an excavation by fracturing the material and casting it into a desired configuration. In its simplest form, this technology involves detonation of a single explosive charge buried at the proper depth to produce a crater which is roughly hyperbolic in cross section. The types of craters produced by various depths of burial are illustrated by Figure 1. Single or Multiple rows of charges are used to excavate linear cuts required for water conveyance or navigation channels. .More complex explosive excavations include small craft harbors, railroad and highway cuts, and removal of W1denvater rock barriers to navigation. While the literature indicates widespread use of large explosions in the (1) ERRO is a field activity of the Waterway Experiment Station, Vicksburg, Mississippi

Jan 1, 1971

By J. B. Webster

Health and Safety in the work place is of primary concern to the underground coal industry. Control of dust in the underground environment is of major importance in this concern. Utah Power and Light Mining Division has undertaken extensive studies to determine and control the various sources of respirable dust in underground high production sections. Determination of dust sources has been achieved by real-time aerosol sampling and standard gravimetric sampling on individuals and in various suspect locations. Some sources are diesel roadway dust, outby crushing, and handling equipment, face sloughing, water spray roll-back, and mining equipment. Once identified, the dust sources are suppressed or controlled and/or the workers are directed from areas of greatest potential exposure.

Jan 1, 1990

By F. P. Schwarz

Even in an otherwise care-fully done sampling procedure, reducing subsample weight, or splitting, when the grain size of material is too large commonly generates significant error. Such error can be estimated from the standard deviation of differences between values of PAIRED ASSAYS. Samples from split-ting steps immediately before comminution, and showing a restricted range of grade, generate paired assays. Splitting steps characterized by relative standard deviations exceeding 16% generate nonrepresentative data. Such steps should be redesigned to optimize reliability of assay-dependent studies. A sampling scheme can be graphically characterized, and then redesigned as appropriate, using a SAMPLING NOMOGRAPH. Use of the nomograph avoids continued replication of assays. Generally at a splitting step, excessive error can be reduced by comminuting more material. Unnecessary effort can be mitigated by comminuting less finely and/or by splitting to a smaller weight.

Jan 1, 1992

By T. Krichler

"Current mine control stations are either single-position systems with high engineering effort or all-in-a-box solutions with low integration possibilities of third-party devices. Above all, both approaches are cost-intensive and not feasible for small companies. This paper shall be an inspiration of how to enhance the productivity and monitoring of an existing mining system in a modular way by introducing a proven technique of the ongoing digital revolution: A Wi-Fi network based on the communication protocol OPC UA. The starter kit consists of a single-board computer, a WLAN access point and any electronic sensor. INTRODUCTION The majority of the European mining industry is run by small and medium deposits (Europe Geology, 2017). This is due to the fact that most ore mines in Europe are widely distributed within the continent, are generally small and additionally they are often steeply inclined. Such ore bodies are normally mined with underground mining methods and must be excavated with high selectivity because of their small thickness. That is why the economy of scales, higher efficiency through bigger machines, cannot be used in most deposits in Europe except for lignite mines. It is important to find an alternative possibility to improve the efficiency of European mines for making them competitive internationally. For cost optimization and profit maximization it is necessary to use the trends of industry 4.0 and to broadcast these into the mining industry to reach a technological advantage. The goals of the EU within the Horizon 2020 funded project are to shorten the actualisation of the mine and block model to hours, improve the communication with Through the Earth (TTE) via very- or ultra-low frequency for long-time monitoring of the abandoned workings, and develop a cost-effective mine control station for optimization of mining processes in Small and Medium Enterprises (SMEs) as well. This paper deals specifically with the new approach for data acquisition, transmission and visualisation of a mine. SCADA AND ERP IN MINING There are already many Supervisory Control and Data Acquisition (SCADA) and Enterprise Resource Planning (ERP) programs on the market, but these are normally not developed for the mining industry. At the moment this leads to three options. • To hire a system integrator, who shall build a complete control station for one mine that requires a high amount of knowledge in programming and cannot be maintained by the mining company itself. • To buy different types of out-of-the-box systems, whereby every system can include some of the used technology. In this case a huge amount of project engineers and operators – at least one per system and shift- is required. • To buy every machine and program from one company including the service contracts."

Jan 1, 2018

By W. E. Lindquist

Roasting of refractory gold ores has the primary goal of oxidizing sulfides and organics to improve gold recoveries prior to leaching. Commercial installations currently utilize bubbling and circulating fluidized beds. The principle of flash roasting is aimed at a more cost effective method of whole ore roasting for large throughput applications. Results of pilot plant testing and scale up to commercial design will be discussed in further detail in this paper.

Jan 1, 1993

By T. Wisdom, D. Romo, G. Seale, R. Jansen

Thickening remains relatively misunderstood since it is typically near the end of the process and not directly involved in metal recovery. When operating well, thickeners are ignored and left to run independently, the ‘out of sight, out of mind’ phenomena. However, when operating poorly, there is a lack of basic understanding and remedial actions to solve issues are reactionary rather than proactively addressing shortcomings. This series of papers breaks down in sequential order the stepped phases required to gain an appreciation and thorough understanding of the science behind thickeners, and key thickener components, and basic troubleshooting skills. This second paper starts with identifying the different approaches to thickener test work including static and dynamic settling tests followed by high-rate versus paste thickening. Complimentary to test work, the mechanisms surrounding coagulation and flocculation are presented and explained. The basic mechanisms for coagulation and flocculation are discussed to support the different test work approaches and provide the reader with the basic background.

Mar 2, 2022

By M. E. Smith

Chile is the world's largest copper producer and as such sets the standard of practice in copper SX/EW design. The authors summarize the liner systems used at many of Chile's major copper producers both operating and planned. The evolution in the state of the art is also discussed, considering both economic factors and Chile's burgeoning environmentalism.

Jan 1, 1994

By W. E. Lytle

Environmental permitting is a critical component for joint-venture projects located in the Commonwealth of Independent States (CIS). This paper presents the basic CIS regulatory environmental requirements for permitting of a hypothetical mining source and emphasizes air permitting. Topics which will be covered include: the Expertiza process, air pollution quantification, data requirements, and air pollution modeling protocol. A comparison will be made between permitting requirements for air pollution sources in the United States and a CIS country, Kazakstan.

Jan 1, 1998

By Wilson Blake

The occurrence of rock bursts in some deep mines throughout the world constitutes a severe operational hazard. In addition to endangering the safety of the miners, the rock-burst problem is a major factor in mining economically in deep mines because of the loss of production and expense owing to cleanup and repairs following a burst. Developing means of controlling or eliminating rock bursts has been the subject of intensive research for over 50 years. While much has been learned about the effects of rock bursts, little is known about their basic causes; hence, control measures have been at best only partially effective--attested to by the number and severity of bursts that continue to occur throughout the world each year. In the Coeur d'Alene mining district of north Idaho, the rock-burst problem continues as the silver and lead veins persist at depth. These veins are presently being mined at greater than 7,000 feet below the surface and will be mined to some 10,000 feet in the future. The majority of rock bursts in this district occur in pillars. While pillar bursting has been essentially eliminated in some deep-mining districts by longwall techniques, modification or application of this technique to the thin, irregular, and near vertically dipping veins of the Coeur d'Alene district has not been found to be practical. The creation of pillars is a consequence of the horizontal cut and fill mining method used. Figure 1 shows a vertical longitudinal projection of the silver vein at the Galena mine, illustrating the mining method. Stoping progresses between raises and is carried upward between levels. A horizontal pillar is created as a stope approaches a mined-out level. Recent broad-band micro seismic monitoring of rock-burst-prone stopes by the Bureau of Mines has shown that potential burst zones could be delineated weeks in advance of a burst and that a definite sequence of events took place prior to the occurrence of a pillar burst (1). Hence, time was available for control measures to be effected when a stope pillar reached a critical burst geometry.

Jan 1, 1971

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 1998

By Chris Ashton, Andreas Rädle, Taner Aydogmus

"The Contract C310 is part of the current biggest infrastructure project of Europe “Crossrail” which is a major new cross-London rail link project and comprises the construction of the North Woolwich Portal, Plumstead Portal and the twin tube Thames Tunnels with a length of approximately 2.6km. Two Mix-Shield TBMs (Diameter 7.12m) were driving through differing challenging ground conditions (Thanet Sand, Gravels, Flint and Chalk) below the ground water table. The two tunnels were underpassing several listed buildings, sensitive structures, operational railway tracks with low overburden and close to existing subway tunnels in an urban environment. Several additional measures as compensation grouting, micro piles and an intensive monitoring has been carried out to ensure a safe tunnelling process. PROJECT OVERVIEW CROSSRAIL Project Crossrail Crossrail is currently the biggest infrastructure project in Europe which has been developed to serve London and the southeast of England. The project includes the construction of twin-bore tunnels on a west-east alignment under central London and the upgrading of existing National Rail lines to the east and west of central London. The new rail track, as shown in Figure 1, starting in Shenfield/ Abbey Wood in the east of London and ending in Reading / Heathrow Airport in the west of London, includes the construction of nine central area stations, providing interchange with London Underground, National Rail and London Bus services, and the upgrading or renewal of existing stations outside central London.Altogether there will be 118km of new rail tracks, including 42km of tunnels and 40 train stations. After completion in 2018, Crossrail expects 200 million passengers per year (Tauriainen, Rädle, Ingram 2013)."

Jan 1, 2016