Search Documents

By Kenneth C. Stewart

The overall purpose of this study was to develop and evaluate, in the laboratory, instrumentation and procedures which might allow for the use of physical measurements of earmuff attenuation which would yield results equivalent to those obtained from psychophysical measures of attenuation. The ultimate goal was to evaluate techniques which might subsequently prove feasible for physical measurement of earmuff attenuation in the field. Current instruments were modified to have a response similar to differrences observed in earmuff attenuation as observed in Volume 1 of the current contract. Mining noise spectra were selected and presented to a single subject seated in a diffuse noise field. The subject wore one of the muffs evaluated in the earlier study and was also fitted with two physical sound measurement systems. A linear system measured the "outside" noise level and a linear system plus "correction" filter measured the "in-side" noise level. These measurements indicated that, under the procedures presented in this report, a laboratory method for measuring earmuff attenuation is feasible and yields results comparable to an extensive psycho-physical procedure.

Jan 1, 1980

By Donald E. Ralston

The Huntsville study area in northeastern Alabama consists of Jackson, Limestone, Madison, and Marshall Counties. Major emphasis was placed on the Huntsville urban area in Madison County to analyze the relationship of urban growth and the minerals industry. Huntsville was delineated into its component urban, suburban, and rural parts for 1964, and the primary area of growth was predicted for 1990. Population estimates were made for the four-county area as a unit and Madison County separately, and projected to 1990. Demand estimates for crushed stone and sand and gravel were made for the same area units and projected to 1990. Analysis of quarry sites in the Huntsville area was made for the present and for the future. The mineral operations of the study area are all located in rural areas; in the case of Huntsville, the mineral sites are located in areas defined as "rural" in the component urban-suburban-rural system. The operations outside Madison County can expect to have minor problems with urban encroachment, while those operations in Madison County can expect major problems associated with urban growth and development. Some of the problems associated with limes tone production can be reduced if producers invest in capital equipment that will reduce the nuisances inherent in this activity. Although urban expansion endangers some quarry operations in Huntsville, topographic and political restrictions which prevent urban expansion can effectively shield quarry operations for some time.

Jan 1, 1970

By AIME AIME

SECOND only to the February Annual Meeting of the Institute are the Regional and Divisional meetings held in the fall of each year. Six such gatherings are scheduled in the next the months, with something likely to interest every member of the Institute. A brief résumé of the programs follows. Regional Meeting Vancouver T HE regional meeting of the Institute will be held at Vancouver, Sept. 13 to 20, in conjunction with the annual western meeting of the Canadian Institute of Mining and Metallurgy. The pro gram appeared on page 350 of MINING AND METALLURGY for July and-proof of careful preparation-a month later re- quires no correction and little elaboration. On the technical side there are few changes. A new item on the Wednesday morning program is the paper, "Investigation of Residential-type Stokers," by H. F. Yancey, supervising engineer, Northwest Experiment Station. U. S. Bureau of Mines, Seattle. As to entertainment the meeting is taking on some most pleasurable aspects. Two notable excursions have been arranged.

Jan 1, 1937

The prevention of silicosis by metallic aluminium has been reported by Denny, Robson, and Irwin in two papers. The first was published in 1937; the second in 1939. The results definitely established that silicosis was prevented in animals by the inhalation of small quantities of aluminium. The present communication records subsequent progress in this field of research.HARMLESSNESS OF ALUMINIUMAnimal experiments having served their purpose, it became necessary to consider means to test the discovery on humans. A question for immediate consideration was: Is aluminium harmful to man when inhaled as a fine powder? While the animal experiments were reassuring, since they conclusively showed the powder to be innocuous when breathed by animals, it was, nevertheless, desirable to have additional reassurance with regard to its effect upon human beings.Through the courtesy of the Aluminium Company of America and especially the valued interest in this problem displayed by that Company's Director of Research, Dr. Francis C. Frary, a study was made of the records pertaining to the health of a group of 125 employees who had for many years been engaged in the manufacture of finely powdered, metallic aluminium for the paint and ink industries. The conditions were such that these employees had inhaled varying and oft-times very dense concentrations of this powder daily over periods ranging from 6 to 23 years, the average 101 the group being 12 years. X-ray pictures of their chests showed no abnormalities attributable to aluminium. Their general health seemed better than that of the 3,000 workers in other sections of the plant. In fact, the early films of three employees in this group of 125 showed shadows suggestive of minimal tuberculosis, which shadows were not discernible in films taken after considerable periods of exposure to aluminium powder.The harmlessness of aluminium was; by this study, reasonably well established at the outset, a finding subsequently verified by Ontario research on humans.PROPOSAL TO TREAT HUMAN SILICOSISBased upon these findings, a proposal to treat silicotics with aluminium was discussed by officials of the Mclntyre Mine and the Banting Institute.

Jan 1, 1945

The New Zealand microcontinent is relatively well endowed with gold deposits; its past gold production per unit area of 3.2 kg/km2 ranks high on a world scale. Total recorded production (1857 - 1986) is about 854 000 kg and most of this gold was mined between 1861 and 1920. There has been a strong revival in gold exploration and mining since 1979, with exploration expenditure of around $15 million per annum and a declared gold production in 1986 of 1265 kg (886 kg in 1985). In addition to numerous alluvial gold recovery plants working small to medium sized deposits (mainly in Westland and Otago), there are five medium to large projects that have started production (Martha Hill), or have reached advanced stages of construction (Grey River dredge), permitting (Golden Cross and Macraes) or exploration (Globe-Progress). This summary paper is taken from reviews by Brathwaite et al (1986) and Brathwaite (1988).

Jan 1, 1988

By Robert S. Hendricks

LOCATION AND HISTORY The Lakeshore Copper property is located on the Papago Indian Reservation approximately 30 miles South of Casa Grande, Arizona. This major porphyry type deposit was discovered by El Paso Natural Gas Company in 1966. Following an extensive diamond drilling program, El Paso invited several mining companies, including Hecla, to examine the property with a view towards participation. Hecla's examination, and the attendant feasibility studies, led to agreements, which were finalized in September 1969, whereby Hecla would acquire a 50% interest in the property, and would act as operator. The Lakeshore deposit covers an area approximately 3,000 feet in width by 6,000 feet in length. It consists of an upper zone of disseminated copper oxides, averaging approximately 100' in thickness overlying a zone of disseminated copper sulfides up to 1,000 feet thick. Near the base of the disseminated ore is a blanket like zone of high grade copper sulfides, referred to as the tactite ore body. The mine is being developed to produce approximately 6,500 tons per day of oxide ore and 9,000 tons per day of sulfide ore. This represents a total daily production rate of 15,500 tons per day, which will be achieved by underground mining methods using rubbertired dieselpowered mining equipment. DEVELOPMENT LAYOUT The mine is being developed by two parallel 15° decline tunnels. The declines were collared 5,000 feet southeast of the ore body, and are being driven in a northwestery direction, to pass beneath the tactite ore zone. The declines will constitute the primary means of access to the underground workings. One decline (north

Jan 1, 1997

By J. S. Roberts

"Campbell mines has been in operation since 1948. Part of the process consists of roasting of a flotation concentrate which contains arsenopyrite.At present operation level the milling rate averages about 850 t.p.d. and about 48 t.p.d. of concentrate is roasted. The gas emissions at present contain between 3 and 3.5 t.p.d. of arsenic trioxide, about2 - 2.5 t.p.d. of particulate matter and between 19 - 25 t.p.d. of sulphur dioxide. The particulate is extremely fine calcine dust and it assays about 4 oz. Of gold per ton.Until 1974 the gas was discharged untreated through a 125' stack.UntreatedThe decision was made in 1972 to erect a gas treatment plant, construction ran through 1973 and operation began in 1974. The cost of the installation was about 1.3 million dollars.On investigation the process technology, it was apparent that the plant operated by giant Yellowknife for the same purpose was the model we should study. I would like to acknowledge the fine cooperation we had from giant, the plant that emerged is very similar to theirs and incorporates some improvements suggested by them and based on their operating experience.The plant is designed to remove arsenic and solid dust and it has no provisions to remove sulphur dioxide.We depend upon the 125' stack to assure adequate dilution. Because of the nearby airport the stack cannot exceed 125'. A stack burner is provided that can ""y used to heat the stack gas and carry it higher into the atmosphere when there is an inversion condition.The removal of arsenic from hot gas is fairly simple. The sublimation point is about 425°f, a few degrees above this point the arsenic is a gas and a few degrees below it condenses into a solid form. The arsenic could have been removed by simply dropping the temperature below the condensation point and collecting all the solids in a baghouse. This would have removed the possibility of recovering the gold in the calcine dust and would have produced an impure and more bulky arsenic material to be placed in safe storage. The decision was made to collect the solid dust in a hot electrostatic precipitator operating above the sublimation point and subsequently lower the temperature below the condensation point and collect the arsenic in a baghouse."

Jan 1, 1976

By P. R. Day, W. K. Webster

"The introduction of large boreholes underground initially involved taking the techniques of open-pit bench blasting to the production stope, but with deeper boreholes and narrower stopes more controlled techniques must be developed in order to maintain good stope walls and prevent dilution of ore or structural damage to pillars due to blasting overbreak. The points discussed are drilling accuracy and drill pattern, the relationship between open-pit wall control and underground mining, the varied explosives products and initiation devices available, and some of the many ways that variations in loading, such as deck charging, etc., can produce desirable results.IntroductionThe use of large-diameter blastholes for underground mining began ten years ago and today they are widely employed in a variety of orebodies and stope configurations. These big blastholes, which range in size from 4.5 to 8 inches in diameter, were originally employed in the same manner ' as open-pit bench blasts; that is, the stope was silled out to full width and all holes were drilled vertical and parallel. This was suitable for competent, massive orebodies, however the popularity of the big drills saw their usage in more narrow stopes, often with poor ground conditions. The dipping orebodies and small drill sublevels resulted in inclined drilling.Today, there is full-ring drilling of 4.5-inch holes. Some 6.5-inch holes are drilled up to 350 feet deep. A 350-foot borehole may contain 6000 to 7000 pounds of explosive. The detonation of this size of charge weight within the confines of an underground stope can have considerable effect on the stability of stope walls and adjacent pillars. Obviously, precautions must be taken to minimize the damage which would result from the large charge weights possible with these big boreholes."

Jan 1, 1982

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

By R. P. Stahura

Conveyors are the lifeline of mining and processing operations. They continuously supply materials to and carry finished products and waste away from operations. When conveyors are running at less than maximum efficiency, the operation's productivity is in trouble. Inefficient conveyors suffer carryback, leading to the buildup of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points. This causes accumulations that can damage the belt, wear moving components and increase both clean-up labor and maintenance expenses. They wander or mistrack, spilling material and endangering personnel and conveyor components. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses occur in lost production, increased downtime for service and maintenance and replacement costs for prematurely worn equip¬ment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization. As a result, other departments relax or operate at less than peak performance. Quality goes down along with employee morale. Costs of inefficient conveyors A key to efficiency is handling a product as few times as is necessary. That means conveyors should be loaded, track true to the unloading point and then be unloaded, all without material escape or waste motion. An inefficient conveyor is often signaled by accumulations of DURT - material that has escaped from the system and is now at large in the plant. This DURT adds costs to an operation that are uncounted and, perhaps, uncountable.

Jan 1, 1992

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

Rutile Beach Sand from Hard Rock

Sep 13, 2010

The upper amphibolite-grade mctasediments of thc rinaroo area, North Queensland, form part of a regional aurcole to the large Tinaroo Batholith and are the stratigraphic equivalents of the Hodgkinson Formation of gencrally low metamorphic grade. There is no evidence of any lithological unconformity.The higher grade metasediments have a more complex deformation history than is typical for thc surrounding region and this may bc due to one or a combination of two factors; an additional strain componcnt associated wilh the intrusion of Ihe Tinaroo Batholith, or a more marked finite strain response to the overall regional stress field within hotter. more ductile rocks.Four deformational events can be characterized within Ihc Tinaroo Area. Close to Ihe Tinaroo Batholith D1 and D2, arc so strongly developed that they disrupl the continuily of Ihe original Iithological layering. In the aureole region, D1 is strongly overprinted and its original fabric intensity is obscured, but both D2 and D3 display a mappable decrease in intensity away from the granite margin. These three deformations occurred during Carboniferous or early Permian time. D4 is later and only patchily developed.The broad, moderate pressure metamorphic aureole surrounding the Tinaroo Batholith is a typical of the CairnsCooktown group of Permo-Carboniferous granitoids. which usually develop narrow, lower pressure contact aureoles. Two periods of metamorphism are distinguishable. The first reached peak temperatures somewhat greater than 520°C, the second temperatures around 620-630° C immediately adjacent to the granite contact.Several cale-silicate lenses containing scattered scheelite mineralization occur within the area. Scheelite appears to have crystallized at the same time as the cale-silicate minerals, its appearance coinciding with the intrusion of the Tinaroo Batholith. Unlike many "skarn-type" scheelite deposits, the scheelite-bearing cale-silicates are Fe-poor, with no positive correlation between total Fe and W.

Jan 1, 1982

By John Meuth, Brandon Fryman, P. E. Hoffman, Joshua Ph. D., P. E. Calnan, Josh Ph. D.

Quantitative Risk Assessment (QRA) can be specifically tailored for use by the commercial explosives industry to calculate risk to employees and the public from commercial explosives facilities and operations. This methodology has several advantages over the American Table of Distances (ATD) which is solely a Quantity Distance (Q/D) analysis. While the ATD has remained essentially the same for 100 years, the safety of commercial explosives in storage has increased immensely. However, the concepts behind QRA calculations are not as intuitive and even at the end of the calculations the values of risk must be compared to something. A few regimes for assessing an acceptable level of risk are discussed in this paper. Risk levels for various United States Federal entities and international agencies are highlighted and suggestions for acceptable risk criteria for individuals and groups are provided. Referencing risk levels from normal daily activities is also done in this paper to make relative the accepted risk criteria. This paper presents some relevant individual risks for everyday activities and some scenarios for group risk for comparison. Individual risk is a straightforward concept however group risk is more complicated. This paper aims to clarify these concepts and provide means to communicate them to the public.

Jan 1, 2019

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

By N H. Jansen, H L. Bridgwater

Field portable X-ray fluorescence (XRF) and near infrared (NIR) instruments are proven technologies in the minerals industry. The in-field results of these instruments can add value early in the project life, leading to cost-effective decision-making compared to their equivalent laboratory based techniques. However, in order to add value to a project, it is crucial that the instruments are employed correctly.Orientation studies should be carried out prior to initiating a sampling program to achieve the highest level of quality assurance and control for the results. Hence, an appropriate sampling workflow begins with considering what outcomes are required, including level of precision, accuracy, reliability for elements and minerals of interest, and sampling errors. The workflows proposed include soil sampling and reverse circulation and diamond drilling sampling techniques, and laboratory based techniques. They are practical and flexible workflows using available portable XRF and NIR technologies that can be applied to current sampling and drilling methods.The combined technologies have the ability to create large, integrated geochemical and mineralogical data sets that can provide cost savings for every stage of the mining chain from exploration to prefeasibility, mineral processing and environmental remediation.CITATION:Jansen, N H and Bridgwater, H L, 2017. Proposed workflows for portable X-ray fluorescence and near infrared instruments for soil and drill hole sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 219–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By F. Qi, T. Frišcic, C. Mottillo

"One of the principal goals of modern industry is to minimize the environmental impact and increase the materials- and energy-efficiency of transforming raw materials into valuable products. This paper will highlight our latest laboratory-scale research in low-energy, low-solvent reactivity of metal oxides and their conversion into popular metal-organic frameworks (MOFs), zeolitic imidazolate frameworks (e.g. Basolite® Z1200 component ZIF-8), and metallodrugs (e.g. bismuth subsalicylate, active component of Pepto-Bismol®). Mechanochemical ion- and liquid-assisted grinding (ILAG) and ""accelerated aging"" techniques will be presented, along with novel low-energy and solvent-free approaches, inspired by geological weathering processes, for converting metal oxides into metal-organic materials. INTRODUCTIONThe development of environmentally-friendly processes, which would in the same time be more materials- and energy-efficient than the existing ones, is one of the central concerns of modern chemical research. In that sense, the focus of the chemist has been mainly on the preparation of carbon-based organic molecules and adaptation of traditional organic synthesis to the recently delineated ideals of Green Chemistry. However, there is a growing realization within the chemistry community that significant energy, materials, and ecology-related benefits can be achieved and, indeed, targeted in the transformations of materials that are typically associated with inorganic chemistry and minerals processing. The principal aim of this highlight contribution is to illustrate how, through the use of approaches associated with solventfree chemistry and mechanochemistry (James et al., 2012), one can develop a clean and efficient system of chemical and materials transformations involving oxide precursors that normally belong to the realm of inorganic chemistry and mineral processing. In particular, this contribution will provide an overview of the recently developed mechanochemical and solvent-free reactivity of metal oxides towards small organic molecules. These mechanochemical reactions, including the methods of liquid-assisted grinding (LAG, Frišcic & Jones, 2009) and ion- and liquid-assisted grinding (ILAG, Frišcic, 2010), have so far provided a radically different means to construct advanced metal-organic materials (e.g. porous metal-organic frameworks, [MOFs] or metallodrugs) by rehabilitating metal oxides as precursors, eliminating the use of bulk organic solvents, and avoiding the use of high temperatures."

Jan 1, 2012

By Tim O’Neil

The search for precious metals opened up the American West. And Nevada was right in the heart of this development. In the mid-19th century, prospectors seeking gold roamed the hills of Nevada and discovered the ComstockLode. The development of this huge silver and gold deposit began in1859 and was responsible for Nevada’s early entry to statehood. Mining was Nevada’s first industry. In more recent years, the Nevada mining industry has led the nation in gold, silver and barite production. Nevada also produces many other minerals. These include aggregates, clays, copper, diatomite, dolomite, gypsum, lime and limestone, lithium and magnesium compounds, perlite, salt and silica. Even today, Nevada’s mining industry continues to be a major economic force in the state. The mining industry has made more than $10 billion in capital investments in Nevada since 1985. And the value of Nevada’s mineral production last year was about $2.7 billion.

Jan 1, 2000

By Remo Grandori, Manfred Jaeger, Fabrizio Antonini, Luis Vigl

The EVINOS-MORNOS tunnel project with its 30 km of length is one of the longest hydraulic tunnel in the world realised with TBM method. The adverse geological conditions, the high cover and the short construction schedule were a great challenge for the successful construction of this tunnel. The paper will describe: the criteria adopted for the tunnel design, the selection of the construction methods and equipment, the productions of the 4 TBMs adopted and the comparison of the behaviour of the different type of TBMs in the various rock conditions, including special conditions, the characteristics of the adopted in situ and precast linings, a comparison between the foreseen and actual construction schedules, the contractual implications of realising a tunnel in such a severe and complex conditions.

Jan 1, 1995

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

A low noise blast hole drilling system was developed to limit the risk of noise induced hearing impairment in mining operations. Noise induced hearing loss has been identified as a major occupational health risk in SA mines. The noise generated by pneumatic percussion drills is a major contributor to such noise induced hearing. This motivated the South African Safety in Mines Research Advisory Committee (SIMRAC) to commission the development of a low noise rock drill system. The system had to be designed, manufactured, tested and demonstrated in a simulated underground mining environment. The specification required noise levels below 90 dBA. Other important design considerations were ease of manual transport, setting up and operation. The primary design concept was to encapsulate a standard Seco S215 pneumatic rock drill in a composite material tube. The tube is pushed onto the rock face by a pneumatic cylinder and is sealed at the rock face by an elastic seal. The drill is pulled towards the rock face by a rope and pulley mechanism fitted inside the tube. This mechanism is powered by a second pneumatic cylinder. The actions of moving and setting the drill require two persons. However, the team can carry out the drilling function itself on several drills simultaneously because of the self-thrusting design. The drill is supported by two camlocks. The exhaust (air containing dust, water, rock shavings, oil and grease) is removed from the encapsulating tubes via exhaust tube to the end of the stope. In this way exhaust noise and air pollutants are disposed of away from personnel. Tests were conducted in a test stope. Noise levels of under 90 dBA were achieved, thereby attaining the primary design specification. This was achieved without materially compromising ease of handling. Penetration rate was somewhat improved compared to that of the standard drill, so that productivity could be maintained. Keywords: Drill, rock drill, quiet, noise, mine, underground.

Jan 1, 2003