Search Documents

By P. Halsall

Smelters of medium or low grade tin concentrates must recover a high proportion of tin from iron-bearing slags or concentrates; the volatility of tin sulphide makes possible the production of iron-free tin fume. Laboratory work defined conditions which would promote the sulphidisation of tin slags and concentrates melted with them, to result in tin recovery as fume, and a residue of less than 0.5% Sn content, which could be controlled to vary with the value of tin. Subsequently pilot-plant work on 6-tonne and 15-tonne scale led to a commercial plant of 45 tonne. capacity (1962), for melting and fuming primary and secondary low-grade tin materials by submerged combustion. Some factors contributing to the rate of Working expressed in terms of the 'half-life and the amount of work done, the 'half-life-tonne' are studied, leading to the design and operation (1972) of the 100-tonne water-jacketed unit, presently in use, treating a wide range of slags and low tin-content ores and residues.

Jan 1, 1983

By Leonard Harris, Rosa H. Harris

"It is becoming increasingly obvious to mining and exploration companies, when operating overseas, that their activities should not conflict with the interests of the surrounding communities. The world's largest gold heap leach operation, Minera Yanacocha has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted with joint venture partners consisting of the company, the community people, the contractors and suppliers, government and non government organizations and a ladies association composed of the employees' wives and female staff.IntroductionThe l 990's is the decade highlighted by enormous investments in mineral exploration and mining projects in the developing world. Figure 1 illustrates the distribution of exploration spending by mining companies in 1995."

Jan 1, 1997

By W. G. Davenport

A flash furnace can be run many different ways. It can, for example, be operated with: (a) highly 02"enriched, ambient temperature blast and no fossil fuel (b) considerable fossil fuel and hot, slightly Or enriched blast. It can also produce different grades of matte. With all these possibilities, the flash furnace operator can benefit from any technique that will indicate the 'best' way to operate his furnace. One such technique is Excel's 'Solver'optimizationroutine#. This chapter shows how our matrices and Excers optimization.abllity can be used to optimize a flash furnace operation. The chapter sets three optimization goals: (a) minimum industrial oxygen + oil cost, $ per tonne of concentrate (b) maximum smelting rate, tonnes of concentrate per hour (c) maximum profit, $ per hour.

Jan 1, 2001

By Vladimiros G. Papangelakis

During the past five years, chemical modelling work at the University of Toronto has elucidated the role of soluble magnesium on the autoclave acidity and has demonstrated why feeds rich in magnesium, and other divalent metals, require more than the stoichiometric requirements in acid to produce a leaching performance comparable to that of low magnesium feeds. This understanding has allowed the calculation of acid additions to the pressure acid leach (PAL) on a less empirical basis. Optimizing acid additions to the PAL confers savings in neutralization costs, ensures high productivity and minimises corrosion problems. Hence, our picture of the solution chemistry inside the autoclave during the PAL process has been substantially improved and is reviewed here. Experimental techniques based on solubility and direct acidity measurements that support the theoretical predictions are presented. Concepts of chemical modelling of electrolyte systems at high temperature and software issues are also discussed. Finally, a better understanding of the solution chemistry at temperature has led to better kinetics models because all metal dissolution and precipitation reactions are acid driven and controlled. . Therefore, reactor modelling efforts by our group are also presented and a reactor model with very good performance, as compared to pilot-plant data, is also made here. Finally, in spite of the above success in PAL solution chemistry and reactor modelling, significant challenges lie ahead in theoretical data gaps and instrumentation; these are also discussed in this paper. Keywords: Laterites, process modelling, pressure acid leach, solution chemistry, chemical modelling, reactor simulation

Jan 1, 2004

By J. L. Johnson

The U.S. Department of the Interior, Bureau of Mines, investigated recovery of concentrates containing tin, tantalum, and niobium from the Kougarok deposit on the Seward Peninsula, AK. To date, 25 million lb of tin has been delineated in occurrences containing 0.36 to 1.32 pct Sn, and the resource potential is estimated to be as high as 25 million short tons at average grades of 0.75 pct Sn, 0.025 pct Ta, and 0,025 pct Nb. Deslimed ore was concentrated to 54 pct Sn, 0.3 pct Ta, and 0.3 pct Nb, with recoveries of 74 pct Sn and 44 pct Ta/Nb using a Humphrey's* spiral followed by a Deister shaking table. Tin values in the slimes were upgraded to a 5-pct-Sn concentrate using a Bartles-Mozley separator followed by flotation. The 5- pct-Sn was further upgraded by fuming to give a concentrate containing approximately 60 pct Sn. The recovery of the two products combined was 80 pct Sn and 46 pct Ta/Nb, A flowsheet with mill-design parameters resulted from the metallurgical testing. An economic analysis was made based on the proposed process.

Jan 1, 1990

By H. Jiang, S. Yang

"The main processes for nickel metallurgy in China consist of electric arc furnace smelting to produce low grade nickel matte and converter to high grade nickel matte, grinding and flotation to separate nickel sulfide from copper sulfide and direct electrolysis of nickel matte. Systematic studies on the properties of electric furnace slag, smelting process for nickel matte, anodic process of nickel matte, cathodic process of nickel electrolysis have been done in our labs. In addition, an approach to a new hydrometallurgy process for nickel matte has been done. The feature of the new process is one stage acidic leaching of high grade nickel matte. The leaching solution could be purified by deposition way or by solvent extraction way. There are two leaching rate-determing steps, chemistry reaction-determing one at temperatures below 600C and diffusion-determing one at temperatures higher than 600 c. The acidic leaching fraction reacted dvaties with leaching time t according to the equation 1-(1- a ) 1/3=kt. The experimental data also show that the leaching reaction rate varies with concentrations of H+, Cl-, and it is also effected by copper sulfide and Cu++. The Cu++ ion can retard the leaching reaction due to forming a copper sulfide layer on the matte surface and the equation 1- 2/3 a. - (1- a: ) 2/3 akt can be used for the case. However the copper sulfide added into nickel matte can facilitate the leaching process. The research work for nickel metallurgy done by others in China has also been mentioned in this paper.Large scale production of nickel in China started in 1960s.The main processes consist of electric arc furnace smelting to produce low grade nickel matte and converter to high grade nickel matte grinding and floatation to separate copper sulfide from nickel sulfide and direct electrolysis of nickel matte.To reduce nickel loss in slag a reseaech group organized by Jinchuan Company and Central South Institute of Mining and Metallurgy (now the Central South University of Technology) measured the viscosity surface tention density conductance melting point and structure of the slag(I).lt has been found that the physico-chemical properties of the slag depend on the components SiO2 ,MgO and FeO but FeO in the slag is too high and the statistic analysis of data from industry gave an equation to correlate the content of Ni in slag with the content of Ni in matte and the composition of slag again it was pointed out that the content of FeO in slag effected the loss of Ni in slag very much (2). The ratio (FeO+MgO) to SiO2shouid be less than 1.13 and the content of Fe3O4should be as low as possible but the reaction"

Jan 1, 1988

By Norbert Patzeh

The demand for nickel is growing and will continue to do so for the foreseeable, future. This will make the construction of new leaching and smelting plants necessary. This paper described a number of possible alternative processes. The first projects with new technology are currently undergoing trials and feasibility studies. Experience from other industrial sectors and from existing plants is being incorporated into these investigations. The question is, to what extent the old nickel producing concepts will continue to be applied in the future. Keywords: Latcritc, rotary kiln, cyclonc rcactor, dust processing

Jan 1, 2004

By Pengfu Tan

NiModel, a thermodynamic model, database and computer program, has been developed to predict the distribution behavior of Ni, Cu, Co, Fe, S, O, As, Sb and Bi, and heat balance in the nickel pyrometallurgical processes such as Outokumpu flash smelting, Outokumpu direct high-grade matte smelting, INCO flash smelting, and Peirce-Smith converting processes. In this model, as much as 16 elements (Ni, Cu, Co, Fe, As, Sb, Bi, S, O, Al, Ca, Mg, Si, N, C and H) are considered. The compositions of matte, slag and gaseous phases, and heat balance are calculated using the thermodynamic data and the activity coefficients of the components derived from the experimental data. The model predictions were compared with the known industrial data from Kalgoorlie Nickel Smelter in Australia, Outokumpu Harjavalta Nickel Smelter in Finland and INCO Metals Company in Canada, and an excellent agreement was obtained. In this paper, the applications of NiModel in the nickel pyrometallurgical industries have been presented. NiModel has been used by Jinchuan Group Limited in China.

Jan 1, 2004

By Edward Rosenberg

The synthesis and characterization of silica polyamine composites modified with a variety of sulfur containing ligands is described. The two most successful ligands in terms of sulfur in-corporation and mercury capture are ethylene sulfide and carbon disulfide. The ethylene sulfide forms either an amino mercaptane or a polysulfide upon reaction with amino groups on the composite. The carbon disulfide undoubtedly forms a dithiocarbamate functional group upon reaction of the amino group under basic conditions. Both materials posses excellent capture kinetics and capacities for mercury, Once captured, the mercury is extremely difficult to remove from the composite materials, even with concentrated acids, and they easily pass the TCLP test. The materials are compared with related thioether modified silica polyamine composites and appropriate potential applications are discussed.

Jan 1, 2003

By François Larouche

Since their commercialization in the early 1990s, lithium-ion batteries (LIBs) have become ubiquitous for powering a myriad of portable electronics. Their usage now extends to the automotive industry and stationary energy storage market. With an average life of 6.2 years and the strong demand, the volume of spent LIBs has increased exponentially, making recycling mandatory. Currently, recycling/ recovery of spent LIBs is limited in comparison to all other types of batteries. The current processes focus mainly on the recovery of the most valuable metals such as cobalt and nickel, leaving lithium and phosphate in a low value end-product. It is necessary that new advanced recycling technologies are developed for the recovery of spent LIBs both from an economic and environmental perspective. In this paper, the current R&D status of LIBs recycling is reviewed with the emphasis placed on hydrometallurgical processing opportunities for Li-ion and Li-solid state batteries.

By Esperidiana A. B. Moura, Célio H. Wataya, Roberta A. Lima, Rene R. Oliveira

The purpose of this study was to investigate the mechanical, morphological and thermal properties of biodegradable composites based on aliphatic-aromatic copolyester/polylatic acid blends (PBAT/PLA blends) reinforced by açaí seed fibers, an abundant byproduct of the açaí fruit agro industry. The biodegradable polymeric composites were prepared by melting extrusion process using a twin-screw extruder machine. The fibers removed from the açaí seed were used as the reinforcement and PBAT/PLA blends as the matrix. The influence of the açaí seed fibers addition on properties of composites was investigated by tensile and impact tests, SEM, DSC, and XRD analysis. Correlation between properties was discussed. In addition, açaí seed fibers characterization by SEM, XRD and WDXRF have also been carried out. The addition of açaí seed fibers on biodegradable PBAT/PLA blends showed that it is possible to get interesting property gains in biodegradable polymer by using waste from renewable sources.

Jan 1, 2015

By Jana Dobrovska

Solidification and cooling of a continuously cast slab and simultaneous heating of a mould is a very complicated problem of transient heat and mass transfer. Nowadays, the solving of such a problem is impossible without numerical models of the temperature field not only of the slab itself, while it is being processed through the whole concasting machine (Caster), but of the mould as well. Two original numerical models have been developed and used in the investigation of a continuously cast steel slab. The first (one of two) 3D model of the temperature field of a concasting is capable of simulating the temperature field of a caster. Experimental research and data acquisition have to be conducted simultaneously with the numerical computation-not only to confront it with the actual numerical model, but also to make it more accurate throughout the process. After computation, it is possible to obtain the temperatures al each node of the network, and at each time of the process. The utilization of the numerical model of solidification and cooling of a concasting plays an indispensable role in practice. The potential change of technology-on the basis of computation-is constantly guided by the effort to optimize, i.e. to maximize the quality of the process. The user can therefore choose any appropriate longitudinal or cross-section of a slab and display or print the temperature field in a 3D or 20 graph whenever necessary. The second numerical model of dendritic segregation of elements assesses critical points of slabs from the viewpoint of their increased susceptibility to crack and fissure. In order to apply this model, it is necessary to analyze the heterogeneity of samples of the constituent elements (Mn, Si and others) and impurities (P, S and others) in characteristic places of the solidifying slab. The numerical model, based on measurement results obtained by an electron micro-probe, generates distribution curves showing the dendritic segregation of the analyzed element, together with the distribution coefficients of the elements between the liquid and solid states. The combination of both models enables the prediction of cracks and fissures in critical points of the continuously cast carbon-steel slab. Both models had been applied in the industrial investigation of a cast low-carbon-steel slab.

Jan 1, 2003

By G. Belardi

The purpose of the study was to check on the level of environmental contamination and to design a project for cleaning up the Abetina Mine area at Piancastagnaio (Grosseto, Italy). Contamination of this area had occurred during the mining and treatment of cinnabar (HgS) over a prolonged period. The aim of the project is to remove the sources of contamination or render them harmless. Mining of the Piancastagnaio deposit started in 1840, mercury metal being extracted from the ore by thermal treatment. Together with Spain, Italy was the first country to produce this metal and was the world leader in this field between 1936 and 1943. Though mercury production in the Monte Amiata region of Tuscany ceased in 1974 the ensuing environmental impact is very evident, taking the form of rusty old mining and processing works, plus waste tips which still contain considerable amount of mercury even after the ore had been subject to thermal extraction treatment. The research which has been conducted included mapping the area to identify the main sources of mercury and arsenic pollution, as well as the level of environmental contamination. Mercury and arsenic values in excess of 16,000 and 150 ppm respectively are encountered in the most highly-contaminated places. The cleanup project has been drawn up on the basis of the field and laboratory investigations. This provides for a combination of remediation measures on the land concerned, as well as in situ inertization of contaminating elements by means of mixtures of chemical compounds such as cyclosiloxanes. Due account has been taken of Italian and EU environmental regulations when establishing the measures for rendering the various polluting element innocuous. 'The efficacy of the inertization techniques has been checked by yield tests in acetic acid and carbon dioxide, reducing the Hg and As contents of the material in the untreated and treated states from maximum values of 7 mgll to minima close to zero.

Jan 1, 1996

By Liangying Wen, Jian Xu, Dongdong Wang, Kaihui Ma, Yang Xu

Slags play an important role in blast furnace operation, and their com- positions are based on the CaO –SiO2–MgO–Al2O3 quaternary system. However, there is not a clear understanding of the effects of gangue on of the formation of FeO-bearing primary-slags process in blast furnace. In this work, the softening and dripping experiments under the blast furnace conditions are designed to explore the influences of CaO-/SiO 2-/MgO-/Al2O3 on the softening and melting properties of FeO respectively. The results indicate that additions of CaO or Al2O3 decrease the starting softening temperature and no dripping behaviors are found in comparison with the base case results when only FeO is used. On the contrary, the addition of SiO2 or MgO rises the starting and ending softening temperature, as well as the dripping temperature. The lowest maximum pressure drop is obtained in the case with addition of SiO2. According to XRD analysis results, the initial phase with CaO addition in the primary-slags should be CaOFe3O4 and that with SiO2, MgO, Al2O3 additions are fayalite (2FeOSiO2), magnesioferrite (MgOFeO), hercynite (FeO2Al2O3), respectively.

Mar 1, 2017

By A. Shemi

Tungsten carbide scrap (WC–Co) is material generated from the tungsten carbide manufacturing process and worn out or used carbide parts from industry. Tungsten (W) ores contain about 3 wt% WO3 and their W concentrates about 10– 75 wt% WO3. Tungsten carbide scrap typically contains 40–95 wt% W. The high intrinsic value of W and the fact that the least valuable scrap contains more W than the average tungsten ore makes tungsten carbide scrap a worthy material for re-use. This study has investigated the selective dissolution of the cobalt (Co) binder phase, and recovery of tungsten monocarbide (WC) and Co using an acid leach process. The Co component was selectively leached leaving the WC solid particles intact. Further investigation using a complexing agent-aided acid leach process that takes advantage of organic chelating agents that form a soluble tungsten complex in place of the passive insoluble tungsten oxide is envisaged. The optimal dissolution of the Co binder phase using an inorganic acid in conjunction with an organic complexing agent is a novel approach with the potential of reduced leaching times and possibility of regenerating the unreacted organic acid.

By Jochen Petersen

Design and operation of heap leach processes are still largely based on,operator experience and rule of thumb. Although considered a low-cost, low-tech route for mineral extraction, the underlying physical, chemical and biological processes are actually rather complex. Numerous heap leach models have been devised over time, but the majority of these tend to simplify the true process and are of limited use in practise. The modelling approach presented here combines the more conventional reaction-diffusion model with models accounting for equilibrium reactions in solution, bacterial growth kinetics, complex reactions schemes, gas flow, heat conservation, etc. One particular model application is discussed in the context of developing a novel high temperature heap leach processes using thermophile micro-organisms. The complexity of processes such as this can only be appreciated with the aid of a systematic model. For the designing engineer an accessible, personal computer based model should be an indispensable tool for the design and optimisation of efficient heap leach operations.

Jan 1, 2002

By Wankun Wang, Fuchun Wang

Based on the study of artificial neural network, the neural model was established for the prediction of germanium extraction from zinc oxide dust by microwave alkaline roasting-water leaching. Alkali-material mass ratio, microwave heating temperature, liquid-solid ratio, aging time, leaching time and leaching temperature were the significant factors for the process. The results indicated that the neural network prediction model was reliable, and the forecast values fitted well with the actual experimental values. The model could be used to predict the regeneration experiments with high credibility and practical significance. The accuracy of convergence of the model reached 10−5.

Mar 1, 2018

By Thomas E. P. Wechsler

The limiting factor for most pyro-metallurgical processes in secondary cop- per melting is the time required to heat and melt the product. American Combustion's proprietary PYRETRON variable £uel/air/oxygen combustion system improves the throughput of existing scrap melting and heating furnaces for copper and copper alloy production by increasing the rate of heat transfer from the flame to the product. The increased productivity and energy savings obtained from this technology can result in sizable reductions in operating costs for smelting operations.

Jan 1, 1991

By Hiroyuki Sano, Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa, Shin-ya Iwahori

"Pyrometallurgical process using Cu2O-based slag was proposed as a recycling process for copper scrap. However, it is difficult to remove nickel from copper by oxidative refining. Therefore, it is necessary to reduce the concentration of nickel in copper before the oxidative refining. In the present work, the copper enrichment stage in this recycling process, where copper scrap melt is separated into the Fe-C-Cu melt and the molten copper, was taken up and the compositions of both melts were measured. Based on the above results, the distribution ratios of nickel between the Fe-C-Cu melt and the molten copper were calculated. Furthermore, the optimum condition of copper enrichment stage was discussed from the viewpoint of nickel removal and copper recovery. The possibility of recovering 4N-purity copper by using this recycling process was confirmed.IntroductionRecycling is well known as a method for saving resources and reducing environmental damage. More than 99% of copper is used in metallic form - as metal or copper alloys[l]. High-grade copper scrap is directly re-melted and reused, while low-grade copper scrap is transported to copper smelters to be pyrorefined and electrorefined. Nevertheless, a great amount of copper is being stockpiled in the cities and should be recycled in the near future. At that time, the current recycling process will face new problems due to the increases in the recycling rate to the smelters. This includes insufficient combustion heat to melt copper scrap and ·almost no benefit in electrorefining because the scrap does not contain gold and silver. Thus, an alternative pyrometallurgical method for copper scrap refining will be required."

Jan 1, 2000

By I. Mc Dougall

"The matte/slag tidal zone in a platinum smelting furnace is subject to severe process conditions which can often lead to premature failure of the lining. The MgO-FeO-Si02 slag is aggressive to refractory bricks, whilst the Ni-Cu-Fe-S matte is aggressive to water-cooled copper cooling elements, and can penetrate and sulphidize refractory bricks, particularly at the high matte temperatures often experienced in the PGM industry. A novel approach to the lining design was taken at Lonmin's new 10MW Furnace 2. An indirectly-cooled graphite ring was applied in the matte/slag tidal zone, with refractory bricks on the hot face. Thermal Finite Element modeling was conducted to determine the optimal lining design in this region of the furnace. The resistance of two graphite grades to damage by slag and matte was evaluated experimentally. The graphite lining is not wet by the matte, and is resistant to slag attack at operating temperatures. In comparison to water-cooled copper in various configurations, cooled graphite shows promise as an indirect refractory cooling system in the tidal zone area of furnaces.IntroductionIn South African Platinum Group Metals (PGM) smelting operations, the PGMs are associated with nickel-copper sulphides in magmatic rocks. After ore is mined, it is concentrated by means of a flotation process prior to smelting. Both rectangular 6-in-line and circular 3 electrode AC submerged arc furnaces are used for this purpose. A new 10 MW round furnace is currently under construction by Tenova Pyromet at Lonmin's Marikana Smelter Division. An overview of Lonmin's smelting operations and Lonmin's approach to smelting high chromite containing PGM concentrates is given by Eksteen et al. [1]"

Jan 1, 2012