Search Documents

By H. Soto, J. Jara, F. Nava

A method has been developed to recover cyanide and copper from solutions containing copper complexes and thiocyanate. Copper is precipitated as copper thiocyanate or as copper cyanide depending on pH and the concentrations of thiocyanate and cyanide in the effluent. The copper precipitate assays over 50% copper and presents good dewatering characteristics. After settling it can be separated from the effluent by filtration. The solution containing the bulk of the cyanide is then oxidized with ozone to transform the remaining thiocyanate into cyanide. This results in a regenerated solution rich in free cyanide that can be recycled to the cyanidation process. Careful control of the pH of the solution is required. First, pH of the effluent is lowered to optimize the precipitation and oxidation stages, then the pH is restored to an alkaline value to regenerate the cyanide solution. Recoveries of over 96% copper and cyanide were obtained in laboratory tests using industrial solutions. With this procedure, cyanocidic gold/copper ores could be treated economically by heap leaching, since the cyanide consumed by the copper impurities could be regenerated at very low cost (most of the cost of cyanide regeneration would be compensated by the copper credits). In order to achieve this, a bleed of the barren solution could be treated by the proposed method, and then recycled to the leaching step. The volume of solution to be treated should be large enough to keep a cyanide/copper molar ratio higher than 3:1. This would assure that copper does not cause undue interferences in the leaching or the carbon adsorption stages. If the thiocyanate content is low, the oxidation stage can be avoided, and the solution can be recycled to the leaching stage directly after the solid-liquid separation stage.

Jan 1, 1997

By Habib Saridikmen

In this experimental study the effects of slag composition on the phosphide capacities of the slag as well as on the phosphorus distribution ratios between the slag and metal phases encountered in ferromanganese smelting have been determined at 1500°C under carbon monoxide atmosphere. The distribution results were employed to calculate the phosphide capacities of the SiO2-Al2O3-CaO-MgO-MnO slags in equilibrium with the Mn-Fe-Si-Csatd.metal phase. The classical gas-slag-metal equilibrium-quenching technique was employed using CO gas atmosphere and graphite crucibles to saturate the metal phase with respect to carbon. The phosphorus distribution ratio increased from 0.045 to 0.375 when the slag basicity increased from 0.72 to 1.39. As expected, the distribution ratio decreased from 0.375 to 0.105 when silica increased from 37 % to 45.8% in the slag phase. The phosphide capacity values were calculated by using the results of experiments. Empirical relationships were developed to express the phosphorus distribution ratios and phosphide capacities of the above slags.

Jan 1, 2006

By Gudrun A. Saevarsdotti

For decades tile aluminium industry has been practicing gas treatment of aluminium melts. This treatment is of great importance because of its influence on 'impurity" and inclusion removal from the melt. The gas-melt interaction is greatly influenced by the gas composition, melt temperature etc. This paper gives an overview of the interaction between argon-chlorine gas mixtures and the aluminium melt. It covers the thermodynamics of the reaction between the chlorine and a number of different elements commonly found in liquid aluminium, and discusses the behaviour of reaction products in the melt. The paper reports an experimental study of the behaviour of the chlorine-molten aluminium interface, using sodium contaminated aluminium melt with and without the addition of grain refiner.

Jan 1, 1996

Physical and chemical methods were investigated to tower thorium levels in Eneabba Ilmenite from the natural levels of 180-500 ppm to give Becher Process synthetic rutile with less than 100 ppm thorium. Chemlcal treatments, but not physical separations were successful. A pilot plant trial of a sodium hydroxide leach (25M NaOH at 75°C and 40 wt% solids for Ih) followed by a sulphuric acid leach (3M H2S04 at 90°C and 60 wt% solids for 211) confirmed that thorium could be removed to below 100 ppm. However, the activity of the ilmenite was not lowered to the same extent

Jan 1, 1996

By C. M. Wai

"Metal species in solid and liquid materials can be extracted by supercritical carbon dioxide containing a suitable ligand. This in situ che1ation-supercritical fluid extraction technique offers several advantages over conventional solvent extraction including minimization of organic liquid waste generation and exposure of personnel to organic vapors. One unique feature of this technique is that metal species can be removed from solid materials directly using supercritical carbon dioxide as a solvent. Several ligand systems including dithiocarbamates, B-diketones, organophosphorus reagents, and macrocyclic compounds have been tested for metal extraction in supercritical carbon dioxide. This novel extraction technique may have important applications for metal recovery and mineral processing.IntroductionSupercritical fluid extraction (SFE) offers several advantages over conventional solvent extraction including the minimization of organic liquid waste generation and exposure of personnel to organic vapors.[1] The high diffusivity, low viscosity, and T-P dependence of solvent strength are some attractive properties which make supercritical fluids excellent candidates for extraction and recovery of organic compounds from solid materials [2] Carbon dioxide is a gas of choice for SFE because of its moderate critical constants (Tc = 31 °·C and Pc = 73 atm), inertness, and availability in purified form. After extraction, the fluid phase is depressurized to separate organic solutes from CO2 gas and the gas can be recycled for repeated use. The SFE technology has been applied to industrial scale operations such as the preparation of decaffeinated coffee and hop extracts."

Jan 1, 1996

By Sung Jin Han

Magnesia-based refractory is generally used in an electric arc furnace (EAF) due to its relatively high corrosion resistance and strength at high temperatures. However, the magnesia refractory is attacked by EAF slag and thus the lining life continuously decreases. Thus, it is significant to identify the interfacial reaction between magnesia refractory and FeO-rich EAF slags. In the present study, the influence of FeO-rich slag on the corrosion behavior of MgO refractory was evaluated. The (Fe,Mg)Oss layer was observed at the slag-refractory interface and its thickness increased with increasing content of FeO in the slag. The specific reaction phenomena and formation behavior of (Fe,Mg)Oss layer were evaluated by thermochemical computing program, FactsageTM7.0.

By Dajian Wang

To obtain the thermodynamic properties of a multicomponent liquid alloy system over the whole range of concentration at an arbitrary temperature, the free volume cell theory has been applied to derive the formula of activity coefficients of liquid solutions based on the infinitely dilute solutions at some temperature. The linear logarithmic relationship between activity coefficients of binary dilute solutions and reciprocal of absolute temperature have been verified, and are in good agreement with the experimental values from the literature. The Monte-Carlo algorithm was used to calculate the nonlinear end value equations of binary systems, then the free volume parameters obtained were correlated with the activity coefficients of liquid binary, ternary, and quaternary systems at an arbitrary temperature. Three dimensional a-X-T diagrams of some binary systems representing the temperature and concentration dependence of activities were plotted. The calculated results regarding non-ferrous alloy systems have been statistically examined with the experimental values from the literature. Hence, this simple approach could be useful for analyzing thermodynamic properties of liquid alloy systems.

Jan 1, 2000

By L. Filip

The roast-leach-electrowinning (RLE) process for zinc was modified to treat two typical complex concentrates containing zinc, lead, copper, gold and silver. Laboratory testwork results indicated that the optimum roasting temperature ranged from 700 to 800°C, in order to produce acceptable residual sulfur levels. The calcined concentrate was subjected to a three-stage leach sequence. The resulting leach solution was purified by hematitic precipitation and directed to the recovery of copper and zinc by solvent extraction and electrolysis. Alkaline smelting and subsequent electrolytic purification recovered the lead and precious metals from the leach residue. A flowsheet was developed based on the laboratory testwork results, and demonstrated in a large-scale pilot plant. The recoveries produced during the pilot plant operation ranged from 90 to 92% for zinc and copper, 85% for lead and 90% for gold and silver, respectively.

Jan 1, 1999

By Ephraim Jeya Kumari

The demand for the titanium dioxide pigments and the shortage of higher-grade titaniferous ores with low radioactivity and zircon sands worldwide has encouraged the development of new techniques for the beneficiation of lesser grade titaniferous ores. The inferior quality ores are invariably richer in radio-active and lanthanide oxides, which severely interfere with the fluidized bed chlorination reaction (FBCR), in which ultra-high purity titanium tetrachloride is distilled off for pigment manufacture. However the present beneficiation techniques require high quality ilmenite ores and are not suitable for upgrading lower grade ilmenite ores which do posses trace metals in the form of lanthanides and actinides as Al-phosphates and zirconium silicates, respectively. The presence of mineral hosts, zircon sand and monazite in ilmenite and anatase also increase in chlorine gas consumption in the FBCR and contribute to a larger volume of hazardous waste production, which must be neutralised at a significant cost before being disposed off safely. In view of the problems described for lanthanide (Ce, Nd etc) and actinide (Th, U) trace impurities in titaniferous ores, an alternative route, which is flexible and more accommodating for processing difficult ores, is discussed. In the new process, which may be used for richer grades of ores too, the ore is roasted in air with sodium carbonate below 950°C to promote the formation of water-soluble sodium ferrite and insoluble sodium titanate phases. In this investigation, the high-temperature roasting process and the ensuing hydrometallurgical leaching steps have been analysed in the context of selective separation of lanthanide and actinide minerals from the main titaniferous mineral structures. Evidences for the selective separation are presented based on the chemical (XRD, XRF, AA) and microstructural analysis (SEM, EDX, EPMA) of roasted mass and the leached product. The efficiency of selective separation is also reported based on the chemicals analysis and the particle size of the materials derived after leaching. The paper highlights the various thermodynamic aspects of reaction equilibrium in the Fe-Ti-O-Na system, and the effect of Eh-pH diagram in the determination of pH required for the better control of the removal of iron and sodium. Two different types of Ti ores, namely ilmenite and anatase, their crystal structure and the phase transformation will also be explained on the basis of wet chemical analysis, XRF, XRD, EPMA and SEM-EDX studies. The method developed examines the technological feasibility of the selective separation process.

Jan 1, 2006

By A. René Silva

The separation of Fe(III) from simulated Ni(II) solutions using different ion exchange resins was studied. The resins tested included cation exchangers with sulfonic and carboxylic groups and chelating resins with iminodiacetic, aminophosphonic, and mixed sulfonic and phosphonic groups. The dosage of resins was varied from 0.1 to 0.5 g/mL to study the impact of resin type and dosage on iron separation from simulated nickel leach solution containing 25 g/L Ni(II) and 25 g/L Fe(III) at pH 1.5. Also, the effects of different metal ion concentrations, Fe (III):Ni(II) ratios in solution, pH, and adsorption times were investigated. Experimental results demonstrate that all the chelating resins selected favored the adsorption of Fe(III) over Ni(II) with high Fe(III) loading. Soft cation exchange resins also favored the adsorption of Fe(III) over Ni(II), but no significant Fe(III) loading was observed. In contrast, strong cation exchange resins did not show adsorption preferences. The most efficient separation was observed using resin with aminophosphonic groups at resin dosage of 0.2 g/mL, having a Fe(III) adsorption over 94% and Ni(II) adsorption below 5%.

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Dumitru Mitrica, Vasile Soare, Elvira Alexandrescu, Mihai Ghita, Marian Burada, Petru Moldovan, Raluca Maria Florea

"Aluminum metal matrix composite Al-Si /SiCp was prepared by reactive gas injection and subsequent remelting. The influence of the remelting process on the microstructure and physicalmechanical properties of the resulted material was investigated. Samples resulted from the synthesis process contained silicon carbide agglomerations in the vicinity of primary silicon and large pore concentrations. In-situ formed silicon carbide presented mostly a polymorphic structure with particle sizes varying from 1 to lOµm. Physical and mechanical properties were largely influenced by the porosity distribution. The remelting process provided a decrease in the composite material porosity and pore size, with significant improvements in the particle distribution and physical-mechanical properties of the composite material. Additions of up to lwt.%Mg in the starting alloy improved the in-situ carbide formation and particles distribution in the solidified material. However, stable and large particle agglomerations were detected in the material in absence of conventional stirring or controlled solidification techniques.IntroductionThe remarkable properties of composite materials (yield strength, stiffuess, hardness and resilience at a reduced specific weight) make them attractive for applications in automotive, aerospace and military industries. Particle reinforced aluminum metal matrix composites (PAMMC) are known for their high strength to weight ratio. The recent development of P AMMC created the possibility to obtain large particles concentrations, exceeding 10% by volume ofreinforcement (SiC, AIN, Al203, etc.). The improvement ofhigh temperature strength and wear resistance made them appropriate for the use in automotive applications, such as the pistons, rotors, disc brakes, and propeller shafts [ 1]. The present main disadvantage of the P AMMCs is their high costs for obtaining and processing related to the final product performance. In order to benefit from the advantages that offer composite materials properties a reasonable production cost - performance ratio must be obtained [2]. Recent innovations in the manufacturing of aluminum-based metal matrix composites provided notable performance improvements but no feasible solutions were found for lowering their present high prices."

Jan 1, 2014

By Preben Ingerslev

Control of the reheating of ingots is based either on surface temperature measurements using optical pyrometers or on furnace set points and reheat time determined empirically. This paper presents a real-time mathematical heat flow model, named BESTT, which calculates the temperature distribution in an ingot cross section when reheated or cooled. The model runs on a 486 PC in less than one minute for a variety of ingot cross sectional shapes such as circular, square and with some considerations octagonal and heavy-cornered square. Initial temperatures can either be uniform or nonuniform while accounting for temperature dependent thermophysical properties. The model was developed and verified using 718 alloy ingots in box type furnaces. When integrated with on-line pyrometric measurements, BESTT can provide for improved feed back in the reheating control loop. The use of BESlT will assist in reducing energy costs, and improving product quality and consistency. EPD Congress 1994 Edited by C. Warren The Minerals, Metals k Materials Sodety, 1993

Jan 1, 1994

By T. T. Nguyen, D. R. Gunasegaram, D. Celentano

"Heat transfer rates at the casting-mold interface are believed to be substantially reduced by the formation of an interfacial gap during the course of solidification of aluminum alloys in permanent molds. In the current work, the effect of force-cooling a permanent composite mold on (i) the initiation and growth characteristics of the gap and (ii) interfacial heat transfer rates are studied. Interesting comparisons are made with the case where no cooling is employed. Casting and mold displacements are measured using L VDTs, and the mold is force-cooled by air jets.IntroductionIn a gravity casting situation where an aluminum alloy solidifies in a permanent mold, a gap initiates and grows between the shrinking casting and the expanding mold (1). It is widely believed that the formation of this gap, customarily referred to as an 'air gap', results in a substantial reduction in the heat transfer coefficient at the casting-mold interface (2), and hence is an important factor in solidification studies.The nature of the air gap formation process is thermo-mechanical. The rate of heat loss from the casting first determines the rate of solidification, which, in turn, decides when the gap initiates. The reason for this is the requirement for the solidified casting surface 'skin' to gain sufficient thickness, and hence strength, to be self-supporting. Once the gap initiates, the gap width controls the rate of heat loss from the casting, which, again, determines the rate at which the gap expands."

Jan 1, 1997

By D. Mukerjee, Ramen Datta, Sanak Mishra, R. Veeraraghavan, K. L. Rohira

"Recent efforts at Steel Authority of India Limited (SAIL) has led to the successful development of atmospheric and marine corrosion resistant high tensile Thermo Mechanically Treated (TMT) bars with minimum specified yield strength of 50 kg.mm-2. These rebars are increasingly being used for a wide range of end-applications, namely, concrete reinforcement structures, bridges, flyovers, dams etc. Welding is an important processing tool for each of the above applications. In view of the importance of welding, a comprehensive evaluation of the weldability properties has been carried for the two grades of steels using Submerged Metal Arc Welding (SMAW) process; the most popularly used technique of welding of reinforcement bars (re bars).Implant tests were conducted to assess the cold cracking susceptibility of the steels. The static fatigue limit (SFL) value, determined for the atmospheric corrosion resistant (Cu-TMT) rebars under no preheat and no rebalcing conditions was found to be 63.8 kg mm-2, which was significantly higher than the Minimum Specified Yield Strength (MSYS) (50 kg.mm-2). This indicates adequate resistance to hydrogen induced cracking (HIC). On the other hand, the SFL value obtained for the marine corrosion resistant rebars (Cu-Cr TMT) under no preheat, no rebaking conditions was found to be inconsistent. Repeat of the test with fully rebaked electrodes (350°C-2h) resulted in a high SFL value (60.3 kg mm-2)_The rigidity of the structure or restraint influences the susceptibility of the weld joint to cracking. The cracking tendency increases with restraint intensity (K) of an assembly. The critical restraint intensities determined for the two steels were found to be· in excess of 1680 kg/mm.mm, indicating good welding behaviour with the following welding conditions : for Cu-TMT rebars with no preheat and no rebaking and for Cu-Cr TMT rebars with no preheat and fully baked electrodes; that is under low hydrogen levels."

Jan 1, 1998

By Forsén. O.

In this ?paper practical solidification of anodes containing nickel, arsenic, antimony and bismuth is compared with the equilibrium? diagrams and kinetic ?factors. In order to clarify the distribution of the impurity elements in the anode the structures were studied after the solidification and also after the electrolysis of anodes. This examination was carried out with optical microscope, scanning electron microscope and electrochemical measurements. All the nickel is remaining metallic in the copper matrix during the solidification and therefore nickel is dissolved in the electrolysis at all oxygen contents, when the nickel content is 0.25 wt-% or less in the anode. The practical .solidification mechanism of the anodes, when the nickel content exceeds 0.25 wt-%, proceeds by the crystallization of nickel oxides. In oxygen containing copper anodes nickel oxide is verified to crystallize together with antimony in certain conditions and to form a micaceous compound (3Cu2O?4NiO?Sb2O5), which may build up a very harmful floating slime in the electrolyte. Arsenic is strongly enriched along the phase boundaries in oxygen free copper anodes. An intermetallic compound Cu3As is formed when the amount of arsenic in the anode. exceeds 0.7 wt-%. This compound is more noble than the copper matrix. This means 'that a selective dissolution of copper-arsenic compounds takes place. The copper matrix dissolves more strongly than the grain boundaries. The solidification structures of oxygen free bismuth containing copper anodes show clearly the influence of bismuth. Thin bismuth films which are less .noble than the metallic copper matrix, are formed during the solid1ficatton process. As a result of this the?grain boundaries are dissolved faster than the copper matrix.

Jan 1, 1987

By P. Blazy

A hydrometallurgical procedure for the recovery of metal from ore, particularly of copper from sulphide materials is described. In the course of this procedure, the raw material is first of all submitted to the action of an appropriate reducing system and then treated with a ferric salt solution which brings about the selective solubilisation of the elements to be recovered with respect to those constituting the pyritic phase. This procedure is investigated using two ore samples proceeding from massive sulphide deposits, presenting different chemical and mine- ralogical characteristics. The results of this investigation are compared with those obtained by a classical process employing a ferric salt solution. It appears that one solubilisation of copper takes place under particularly advantageous conditions when our procedure is used. The principal parameters affecting leaching of zinc, lead and copper are examined. The selectivity of this treatment is evaluated by following the change during the treatment in the pyritic phase.

Jan 1, 1976

By Bruce W. Wessels

"Metal-organic chemical vapor deposition has been shown to be a highly versatile technique for the synthesis of complex oxides. High dielectric constant oxide thin films of SrTiO3, BaTiO3, Ba1-xSrxTiO3 and SrxBa1-xNb2O6 can be be be deposited at 800 ºC with this technique. The fluorine substituted B-diketonate precursors have been shown to be well-suited for the deposition of high quality, epitaxial thin films of these materials.IntroductionThere has been a resurgence of interest in thin film ferroelectric oxides as a result of the development of techniques to deposit high quality material. Both physical and chemical vapor deposition techniques have been realized. Of the chemical vapor deposition techniques, metal-organic chemical vapor deposition (MOCVD) has received the most interest for the deposition of ferroelectric oxide thin films. This results, in part, from the availability of a number of volatile metal-organic precursors.(l) Moreover, MOCVD offers the advantages of high growth rates, uniform coverage over large areas, conformability, abrupt interfaces and excellent epitaxial crystallinity. Of the metalorganic precursors, the B-diketonate complexes have played an important role especially in the deposition of ferroelectric oxides containing alkaline-earth metals such as BaTi03 and Ba1•XSrxTi03. For example, barium tetramethylheptanedionate Ba(thd)2 has been used in the preparation of BaTi03 by MOCVD.(2) These compounds, however, are not without their problems. Ba(dpm)2 has a relatively low volatility; and as a consequence, temperatures in excess of 180·C are required for volatilization. This leads to the necessity of a complex precursor delivery system to insure that the precursor does not condense before the reaction zone. Moreover, the Ba precursor tends to oligomerize leading to a decrease in vapor pressure as well as a problem with reproducibility. To counter these problems, novel liquid source and solid source precursor delivery systems have been developed. (3)(4)"

Jan 1, 1994

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009