Search Documents

By Robert S. Post

A highly respected coal mining company in West Virginia updated their stacker belt by switching to a new magnetic coupling. The savings they achieved are the subject of this paper. A steep incline and heavy belt loads are powered by a dual drive arrangement. The magnetic couplings were custom designed for complete fluid coupling retrofit and easy installation in the field. Maintenance personnel updated the drives in just a few hours. Over the following several weeks, adjustments were made to the couplings for optimum performance. Cost savings are found in reduced down time, no coupling maintenance, and equipment protection.

Jan 1, 2000

By M. W. Harmer, J. M. Quist

Laboratory test work, pilot plant testing and plant experience with wet, fine-mesh screens are discussed. High-frequency, low-amplitude, fine-mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with hot ferric chloride to remove lead and copper contaminants before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1991

By R. D. Lama

This paper presents the results of a large scale trial of polycrystalline diamond picks (PDC) on longwalls with particular reference to dust control. Results from fixed position monitoring showed that PDC picks produced less respirable dust than tungsten carbide Point Attack picks. Dust generation at the longwall face was lower by 39 - 43%. Field trials also indicated that the life of a PDC pick to be at least 1460 tonnes/pick.

Jan 1, 1993

By Clifford J. Lewis

The role of calcareous minerals in that area of the environmental improvement program involving the control or elimination of sulfur oxide emissions is discussed, and a new concept in gas scrubbing, rendering possible the use of calcareous rocks more extensively for this purpose, is presented. Calcareous rocks are defined as the more common limestones, consisting essentially of calcium carbonate and magnesium carbonate. The effect of magnesium carbonate on the reaction rate of limestones and lime toward sulfur oxides in aqueous scrubbing systems is pointed out. The relative economics of lime- stone versus lime as aqueous scrubbing reagents for sulfur dioxide are indicated.

Jan 1, 1974

By C. Babbitt, J. O’Green, N. I. Jayaraman

In many mines, dust-laden air from an entry being driven by a continuous miner will contaminate the intake air to the roof bolter operator and other downwind personnel. Through a US Bureau of Mines (USBM) contract, Foster-Miller Inc. has evaluated several control techniques to reduce the respirable dust exposures of downwind personnel. One fan and tubing technique consisted of bypassing the miner-generated dust directly to the section return. The results of the evaluation of this technique revealed that reductions in dust concentrations of 90% or more can be achieved at downwind roof bolter locations. A second method was to clean the dusty air from the upwind continuous miner by using a dust collector. The cleaned air was then supplied to the bolter through collapsible tubing. An underground evaluation showed reductions of 82% to 96% when the dust collector was operating. A third method was to reduce the quantity of dust contributed by the miner to the return airstream. A water-powered scrubber was installed over the throat area of the continuous miner. More than 1.18 m3/s (2500 cfm) of dusty air moved through five tubes with dust collection efficiency exceeding 75%. Underground evaluation results showed that return dust concentrations were reduced by about 60%. This paper discusses the ventilation and dust control techniques used for personnel downwind of the continuous miner.

Jan 1, 1987

By K. E. Lasaridi

Increasing soil organic matter was considered to be an important factor for the establishment of vegetative cover in abandoned quarries of perlite and bentonite in the island of Milos. For this reason, the feasibility of composting local organic wastes and by-products for use as a soil amendment was examined in this study. A mixture of organic wastes of vegetative origin and seaweed, in proportions that correspond to local material availability, was composted in laboratory scale reactors and the composting progress and compost quality were evaluated. Temperature, airflow and respiration rate were continuously monitored and various compost quality parameters, such as C/N ratio, nitrate nitrogen and seed germination were analysed. Addition of inorganic nitrogen was necessary for the biodegradation of the substrate, while the main problem for the compost utilisation was related to its high electrical conductivity, characteristic of seaweed containing mixtures, which further increased with nitrogen addition.

Jan 1, 2002

By J. W. C. Wong, S. D. Miller, J. J. Jeffery

Pre-mining identification of acid forming mine and waste materials is of concern to the mining industry because of the potential for the generation of acid mine drainage, acid rock drainage, and soil acidity problems. Accurate identification of acid forming material is essential for developing appropriate waste management strategies to reduce environmental problems related to acid generation from sulphide containing wastes. The acid-base accounting procedure, in its various forms , is commonly used for pre-mining screening of mine and mine waste materials. The procedure is generally effective when used and applied correctly but is prone to incorrect interpretation of results which can have significant financial and environmental implications. This paper examines the acid-base accounting Procedure and the possibility of misuse of this method with special emphasis on the sampling method, the sulphide forms, the acid neutralization capacity, and the interpretation of results. Data from numerous coal, base metal, and gold mining operations are used to illustrate the application of the acid-base account. The data base indicates that overall, approximately 1/3 of all waste generated by mining and mineral processing is potentially acid forming indicating the need for correct identification and management. Problems associated with simple application of 'absolute' acid-base criteria for classifying acid forming material are highlighted and the need for developing site specific or 'relative' criteria is discussed and illustrated by case study.

Jan 1, 1991

By C. Cassios

EIA is a procedure aiming the elimination of adverse impacts to the environment from undertaken projects. Historically, it starts in 1969 when NEPA (Nat.Env.Prot.Agency) in the US initiated the EIA ? EIStatement. The EIA procedure was adapted by the European Union with the directive 337/85 and in Greece the Common Ministerial Decision 69269/90 enforced it to the Greek legislation. However, mining enterprises in Greece long before the implementation of the European Directive and in accordance to the legislation of the Public Law 998/79 for the protection of the forested lands were obliged to submit EIA?s and get an approval in order to operate in forested areas. The submitted and approved EIA?s and their implementation by the mining companies were among the positive aspects of the EIA procedures. This paper is examining the impacts of EIA?s in the Greek mining industry its positive aspects as well as their difficulties and their role for the reclamation procedure. The technical and procedural aspects which EIA presents for the mining industry are commented, while proposals, for a more flexible EIA implementation for the Greek Environment are also presented.

Jan 1, 2002

By A. Dadgar, R. H. Sergent

Changes in the ore types available and increased environmental concern have created a demand for an alternative technology to cyanide for the extraction of gold from ore. Great Lakes Chemical Corporation (Great Lakes) believes that halogen chemistry, in particular bromine chemistry, is the best available alternative to cyanide for gold extraction. Great Lakes is a Fortune 500 chemical company with sales of approximately one billion dollars per year. Great Lakes extracts elemental bromine from naturally occurring brines in Southern Arkansas. Great Lakes has developed a family of proprietary bromine compounds to aid in the extraction of gold. In addition to proprietary bromine compounds for gold extraction, Great Lakes has developed a method of recycling bromide ion in the leach circuit. Various recovery methods, including ion exchange and solvent , extraction are currently being studied.

Jan 1, 1990

By E. K. Albert

Title IV of the 1977 Surface Mining Control and Reclamation Act (SMCRA) provides for an abandoned mine reclamation fund. This fund, taken from fees collected from operating coal mines, provides capital for the reclamation process. The Act directs the Office of Surface Mining (OSM) to collect the fees based on coal production. Monies from the abandoned mine lands (AML) fund are distributed through two programs. The first provides OSM with capital to use in emergency situations resulting from abandoned mine sites and reclaiming high priority sites in states without established AML programs. The second distributes the money through a state's AML program in the form of grants. To provide for a flexible and customized selection procedure for AML projects, a management information system (MIS) that combines scientific selection procedures is being developed. This system employs objective and subjective methods developed in systems research in recent years. The MIS component is an essential part of any selection process involving large numbers of potential projects. It must contain all the necessary project parameters that can be applied to the selection of projects whether or not they are to be used in the immediate selection criteria. In addition, variable selection criteria will allow ‘what if’ types of inquiries for comparison of differing selections and benefits.

Jan 1, 1990

By Norbert Patzelt, Johann Knecht, Wolfgang Baum

The principle of high-pressure interparticulate comminution has been used very successfully since the mid 1980's for grinding a wide range of different materials. A number of reports about operating experience have already been published. High-pressure grinding rolls (HPGRs) are currently making their debut in the mining industry. Experience is being gained with test machines, particularly for the comminution of hard rock. In the grinding of diamond-bearing ore, (Fig 1) interparticulate comminution has already become the standard for liberating the diamonds from the matrix. The advantages of interparticulate comminution are also recognized for the grinding of concentrates (chrome ore, iron ore). Numerous HPGRs are being used very successfully in this field. A testing plant for first-time industrial grinding of coarse, very hard and highly abrasive copper ore was built at Cyprus Amax's plant in Sieretta, Arizona (Fig. 2). The operating experience gained here showed that the grinding of very hard ores places particularly high mechanical demands on the mill. While the machine itself meets the high availability requirements, the wear-protection system proves to be the most sensitive point. Naturally, the properties of the ore to be ground exert a considerable influence on the lifetime of the grinding rolls. This paper describes the wear mechanisms and the wear­protection systems designed to combat these.

Jan 1, 1997

By Theodore Budd, Joseph A. Sopko

Ground freezing was selected to provide excavation support and ground water control for the construction of a 457 cm diameter tunnel between two underground structures for a major sewer project in Milwaukee, Wisconsin. Initial plans called for installing horizontal refrigeration pipes around the perimeter of the tunnel. Due to the possibility of difficult conditions associated with horizontal drilling, the contractor elected to drill inclined pipes from the surface. The surface location, however, crossed a city thoroughfare with an extensive system of buried utilities. This paper discusses drilling techniques and utility protection, as well as tunneling methods and production.

Jan 1, 1991

By Curt Morgan

This paper will discuss the value of cream a common information model for the mining industry. Information models are a proven technique for quantifying diverse information in a non-proprietary and easily understood manner. Combining information models with emergent data exchange technologies such as XML and SOAP, the mining industry could substantially reduce the costs of sharing information, reduce dependence on proprietary information systems, leverage inexpensive PC desktop technology, and provide a solid foundation for simplifying mine information systems. The paper will provide an overview of information modeling, discuss practical and proven applications of the modeling technique in the mining industry, propose how such a model could be developed in a collaborative manner and discuss the benefits of such an effort.

Jan 1, 2002

By A. K. Mukhopadhyay

[The mechanical status of a mine ventilation fan can be monitored effectively through vibration analysis. An expert system can be an effective tool in fault diagnosis for a variety of equipment. Computers have made it possible to implement an expert system to analyze the data for correct and appropriate diagnosis. In addition, vibration analysis can provide important information oil the condition of the machine. This paper discusses an approach for an expert system to determine on vibration analysis, practical problems that can occur with a fan. The frequency of the vibration is the only characteristics considered in the analysis, although other variables are discussed in the paper. Finally, a simple computer program, written in Turbo Prolog, is presented. A friendly query system, menu operation and a disk-resident separate knowledge base are a few of the salient features of this system.]

Jan 1, 1997

By Andy Cole, Stanley Bunk, Steve Dunn, Thom McCord

In 1994, Goldstrike initiated a research program to investigate processing options for treating what was then the small amount of carbonaceous ore identified in the reserves. The focus of the research was on developing a process which incorporated the autoclave technology already utilized at Goldstrike. Over the next two years, Barrick pursued the development of an ammonium thiosulfate leaching (ATS) process. During the period in which the ATS research was being conducted the amount of carbonaceous ore in Goldstrike's reserves increased substantially and continued growth was projected. By 1996, significant advancement was made on the development of the ATS process. The work culminated in a series of integrated pilot plant runs incorporating autoclaving, ATS leaching, resin in leach, stripping and cementation. Several questions about the process chemistry remained unanswered, preventing commercial development. Barrick was committed to producing gold from the carbonaceous ore reserves by 2000. A due diligence review of carbonaceous ore processing options was initiated during the second half of 1996. Processes considered in addition to ATS were fine grinding/autoclaving, as practiced then by Santa Fe, and whole ore roasting as practiced by Independence Mining and Newmont. The objective by year-end was to recommend the most robust and economical process for Goldstrike's carbonaceous resources. In the fall of 1996, a detailed review of roasting as a processing alternative for Goldstrike was initiated. Throughout the ATS development period, whole ore roasting was used as the benchmark. All the ATS metallurgical and financial results were compared to roasting bench top test results. It was clear this data was too imprecise for use in due diligence study, a more definitive recovery value was needed to complete the carbonaceous ore review. The primary goal of the roasting review was to conduct pilot plant roast tests to gain a more thorough understanding of Goldstrike's carbonaceous ore's response to roasting and its effects on gold recovery. Using the test facility at Hazen Research, four pilot plant campaigns were conducted to determine optimum roast conditions and further define metallurgical design parameters. Conventional two-stage fluid bed technology based on Freeport­McMoRan's roasting patent was the specific process basis for testing. The ore's response to roasting exceeded expectations. In January 1997, a preliminary economic evaluation comparing ATS and roasting was presented, and the outcome was approval to proceed with a roasting prefeasibility study. In July 1997, approval for Goldstrike's Roaster facility was received and basic engineering started immediately thereafter. Detailed engineering _began in January 1998 and plant construction commenced in October 1998,t, Goldstrike's Roaster facility is designed to treat 12,000 tpd of a refractory gold ore, which contains both pyrite and organic carbon. Circuits in the facility include primary and secondary crushing, dry grinding, roasting, gas handling, neutralization, thickening and standard CIL. Gold desorbtion and recovery is carried out at Goldstrike's existing refinery. Plant start-up of the first dry grinding and roasting train is scheduled for March 2000, with the second train coming online in May 2000.

Jan 1, 1999

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Occasionally, standing supports are used to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for standing supports to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. The Mine Roof Simulator (MRS) was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. Prop models were used to study the effect of a range of roof and floor materials — gray shale, shale and claystone — on the critical buckling loads of the steel props.

Dec 1, 2022

By A. Shah, L. W. Saperstein, M. C. Radomsky, D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the US Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1990

By M. Kaya

The main purpose of this study was to design a modular/mobile coal preparation plant with a capacity of 300 t/h for Seyitömer B3 vein (almost 70% of the whole SLI deposit). Firstly, coal washing properties and washability curves were determined by sink and float tests. Then, equipment sizing, selection, flow sheet development, economic evaluation, investment and operating costs were determined for coarse (-150+18mm), fine (-18+0.5mm) and slime (-0.5+0.1mm) coals. Economic evaluation of the proposed flow sheet showed the feasibility and profitability of the investment.

Jan 1, 2006

By Ron Parks

High Pressure Grinding Rolls (HPGR) was introduced to the mineral processing industries in the mid-SO's as a tool for comminuting raw and processed materials. This tool made its an impact in the Cement Industry where it was used as a pre-grinder on existing ball mills, raw and finish grinding in a mill circuit and other various applications. This concept was a big success where the cost of power was high along with the desire to increase capacity. The HPGR reduced the power requirement and increased the capacity in the ball mill due to the finished product produced by the HPGR and the micro fractures in the coarse rock, which reduces the power required to finish grind the rock. This unit has found acceptance in many other industries including diamonds, iron and other selective applications. The diamond industry uses this tool for selective grinding purposes since the kimberlite rock is considerably softer than the actual diamonds. Therefore within a bed of material, kimberlite is crushed to fines and the diamonds are liberated and unharmed. The iron industry primarily uses this tool for concentrate comminution; however, there are installations using this tool as a pebble crusher and in an AG-pebble mill circuit.

Jan 1, 2000

By Irwan Halim, Stephane Polycarpe, Brian Hann

The Narragansett Bay Commission Phase III CSO Program includes construction of the 11,600-foot long, 30-foot ID, deep rock Pawtucket Tunnel in Rhode Island. This paper provides an overview of the Design Build Project features and highlight some of the important design considerations, features, and innovations, including geologic conditions and related TBM design, and deep shaft and tunnel segment designs. The paper provides the most recent updates on some of the project construction activities including TBM tunnel progress and retrieval schemes, tunnel pump station and deep vertical shaft liner installations, SEM construction, and microtunneling for the longest adit using Fiberglass Reinforced Polymer Mortar pipes.

Jun 23, 2024