Search Documents

By John F. Oyler

The performance of high alumina refractory subjected to high compressive loads and high temperatures is an area in which operating experience is quite limited. This paper documents the results of five months of operation of a combustion chamber lined with 83 pct alumina brick subjected to compressive stresses as high as 45psi and hot face temperatures of about 2750°F. It also describes a method for predicting long term subsidence results based on the limited information available in standard hot load limit tests. Descriptions of the chamber itself and the pilot plant upon which its design was based are included.

Jan 1, 1978

Liebherr Mining Equipment Co., of Newport News, VA and Baxter Springs, KS, introduced the T282, a new two-axle, diesel-electric, AC drive haul truck with a payload capacity of 327-t (360-st). The T282 was unveiled at a press briefing in October 1998 at the company's Baxter Springs research and development1 manufacturing facility. In addition to an increase in pay- load capacity, the truck's AC drive system has been de- signed to allow for easy configuration to a trolley-assist system with minimal additional equipment. The T282 provides fuel savings, reduced maintenance requirements, and reduced downtime and maintenance costs, providing the mine operator with increases in productivity. Basic dimensions and weight of the T282 are: ? Overall length, 14.5 m (47.5 ft). ? Overall width, 8.7 m (28.7 ft). ? Loading height, 6.5 m (21.2 ft). ? Height - body up, 13.9 m (45.9 ft). ? Empty vehicle weight, 201 t (221 st). ? Operating weight - loaded, 528.6 t (582.6 st). ?Engine, Detroit Diesel 16V4000 at 2 MW (2,750 hp). ?Electric drive system, Siemens/Liebherr.

Jan 1, 1999

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

By J. F. Mack, P. R. Michael, J. M. Shapaka, S. J. Self, M. W. Richmond

"On October 11, 2000, an estimated 306 million gallons of water and coal waste slurry drained from an impoundment in Martin County, eastern Kentucky into an adjacent underground mine. Approximately 230 million gallons of the water and slurry discharged from two underground mine portals and affected over 75 miles of streams in Kentucky and West Virginia. In response to this and several other similar events, the U.S. Office of Surface Mining Reclamation and Enforcement (OSMRE) commissioned an oversight study that evaluates how well state and federal regulatory programs established under the Surface Mining Control and Enforcement Act are ensuring that impoundment operators are minimizing the potential for impoundment-basin breakthroughs. The study focuses on slurry impoundments constructed in the hollows of Appalachia where numerous coal seams and steep topography combine to result in a large number of mined seams intersecting and underlying impounding facilities. Factors under consideration include: (1) full accounting of all mineable coal seams intersecting and underlying the impoundment; (2) identification and accurate location of underground mines close enough to the impoundment to potentially affect its stability; (3) assessment of the stability of coal barriers between the impoundment basin and adjacent mines, and stability of roof rock and pillars in mines subjacent to the structure; (4) determination of the flowability of the impounded slurry when expanding or undermining the facility are being considered; and (5) measures undertaken to reduce breakthrough potential when necessary. The oversight study began in 2012 after program-evaluation criteria were defined in an OSMRE technical position paper. The study is scheduled to be completed in 2017. BACKGROUND The Surface Mining Control and Reclamation Act (SMCRA) authorizes the disposal of coal mine waste by constructing a coarse coal mine waste embankment across a valley and pumping the fine coal mine waste (slurry) into the resulting basin (Figure 1). A concern shared by many engineers, geologists, and mine inspectors familiar with coal mine waste slurry impoundments is related to the common occurrence of underground mine workings adjacent to or beneath the impoundment: the potential for slurry “breakthroughs” into mine works and subsequent breakouts into the surface waterways (Figure 2). On October 11, 2000 a combination of coal refuse slurry and water from the Big Branch impoundment in Martin County, Kentucky broke through into an underground mine and subsequently discharged into the receiving streams. The location of the point of breakthrough, pathways of slurry/water flow within the mine workings, and two points where the liquid exited the mine are shown in Figure 3. An estimated 306 million gallons of water and coal refuse slurry drained from the impoundment into the adjacent underground mine. Approximately 230 million gallons subsequently discharged from the underground mine at two portals."

Jan 1, 2015

By Angelus S. C. Owili-Eger

Although the foundation of a unified treatment of fluid flow in variably saturated porous media was established more than seventy years ago, no serious attempt was made to develop it until the early 1970's. Ever since, a number of unsaturated-saturated numerical models have been reported in the literature. However, none of these models have treated multidimensional, multiphase flow in deforming media, parts of which may undergo extensive secondary fracturing. A situation such as this is not uncommon in coal mining operations in which the longwall method of extraction is employed. The present model has been structured to handle such physical systems. This paper presents the mathematical formulation, the numerical algorithm, and a further validation and evaluation of the modified model. The model treats a multiphase flow in a three- dimensional regime and handles mining excavations of complex and changing configurations.

Jan 1, 1980

By K. Osseo-Asare

LIX63 in combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 1.0. Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX63 and DNNS. Increasing LIX63 concentration retards both extraction and strip-ping rates while DNNS has the opposite effect. Slope analyses of equilibrium data indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1978

By V. A. Mironenko

The combined study of ground water regime and rock deformations has resulted in the theoretical substantiation of the common principles for analysis of the hydrodynamic and geomechanical processes Within the scope of unique scientific direction -hydrogeomechanics (Mironenko and Shestakov, 1974). The hydrogeomechanical models are widely used now for the analysis and forecasting the extremely important processes connected with the safe and efficient mining operations, as well as with the protection of geological medium. Among these processes are: -deformations of the open-pit slopes and spoil dumps; -consolidation of rocks due to the ground-water pressure drop; -water-end-rock material inrush into mine workings caused by deformations of the undermined rock mass; -geodynamical processes due to the changes in ground water regime; -artificial hydrofracturing in rocks; -transformations of clay linings under the tailing ponds and other technical water basins.

Jan 1, 1990

By J. D. Miller

Many factors -- political, environmental and technological -- will determine the extent to which the United States realizes the potential of its vast coal resources. Not the least of these factors is technogical development including mining, processing and transportation. With regard to processing technology, about 50% of the 800x106 tons of coal mined annually in the U.S. is processed in preparation plants. The purpose of the physical separations accomplished in these preparation plants is to remove ash (present as clays and other oxide minerals) and sulfur 'present mostly as pyrite). Coal flotation circuits for such separations are becoming more important in the processing of minus 28 mesh coal. (1,2,3) For example in the U.S. in 1960, 31 flotation plants processed 26,500 tpd; whereas in 1980, there were 80 flotation plants which processed 78,300 tpd. This corresponds to an annual growth in flotation plant capacity of 10 per year during the past two decades. Coal flotation is based on the natural or induced hydrophobicity of coal particles which are separated from hydrophilic ash and sulfur constituents by attachment to air bubbles. The coal particle/air bubble aggregates are collected in a froth phase which is created by the addition of a suitable frother such as MISC. Without exception, such separations are made in a conventional flotation cell, which, in essence, is a stirred tank reactor with a shrouded rotor to shear the air as it passes through a hollow shaft. The dispersed air bubbles (4.0 mm diameter) are stabilized by addition of the frother. Collision of the air bubbles with, and/or precipitation of the air bubbles on, the coal particles results in the formation of coal particle/air bubble aggregates which rise in the gravitational field and are collected in the froth phase developed at the top of the flotation cell. Restraints on successful separation by this conventional flotation technique are particle size and retention time. Generally it is found that effective flotation is only achieved for particle sizes between 10 and 1000 microns. Further, with respect to retention time, it is found that a nominal retention time of at least 2 minutes is required for successful separations. These facts limit the effectiveness of conventional coal flotation. Coal fines may be lost in the reject stream and disposal is frequently a problem. The retention time required for conventional flotation results in large floor space demands which limit the capacity of the plant.

Jan 1, 1981

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By R. V. Ramani, S. Shankar

The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies. A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0. 10 mg/M3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed. Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining.

Jan 1, 1996

By K. M. Belingheri, M. E. Smith

Pinson Mining Co. operates a conventional mill and two heap leach operations in north-central Nevada. The latest of these heap leach operations, the Preble project, is a low-grade, low-tonnage property made profitable through several innovative capital reduction techniques. Rapid return on investment was a prime factor in design. To facilitate this, fast-track design and construction techniques were employed. The project is a seasonal 1.5 kt/d (1 700 stpd) crush/agglomerate heap leach plant using both clay and plastic leach pads. Construction and startup were achieved through cooperative arrangements between local contractors and in-house construction personnel, with few items put out to bid. An interactive approach to design minimized lost time and construction costs.

Jan 1, 1987

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1997

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open-pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected, including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1998

By B. Hines

Grinding efficiency in a vertical stirred mill is affected by a wide range of process and mill configuration variables. Of these, the media fill, size, and intrinsic density have a significant effect on power draw and grinding performance. Media-related factors that influence grinding performance include, e.g.,a higher media filling providing additional particle breakage sites, or a lower bead density decreasing the running torque at a given media filling. It has been estimated that the grinding media can cause up to a 30% change in the specific energy required to grind. FLSmidth has generally recommended that the intrinsic density (specific gravity) of the grinding media be more than triple the slurry density. This density difference helps to ensure that sufficient stress intensity is generated in the mill to provide particle breakage. It also reduces the chance of media ?float? if there is a spike in either slurry density or slurry flow rate. The VXPmills have historically operated at slurry density values between 1.2 and 1.5 kg/L, which translates to nominal bead intrinsic density range between 3.6 and 4.5 kg/L. The current trend towards regrinding bulk flotation concentrates to even finer sizes, to improve recoveries of fine grained minerals, has provided motivation to consider closed-circuit operation of stirred media mills. The slurry density in this application is typically higher than in open-circuit operation due to the higher percent solids in cyclone underflows. An additional effect is that closed-circuit operation increases the potential for media float due to higher flow rates as slurry is recycled to the mill. The normal progression in extending the operating range of existing equipment is to carry out laboratory testing before pilot-scale and plant-scale trials. The results presented in this paper examine the media density to slurry density ratio and its effect on grinding performance.

Feb 23, 2014

By Leon D. Keller

Fine screening, as discussed in this paper, pertains to the use of the Rapifine DSM Screen to make a 65 to 325-mesh separation at production tonnages. The greatest number of Rapifine Screen installations are in magnetic taconite plants where the unusual relationship between the grinding mill, cyclone classifier, magnetic separators, and fine screens makes the Rapifine Screen application unique. Since the initial fine screening installation on magnetite in 1961, (1) additional installations and further testwork have contributed to the fund of information which is the basis of this paper. The addition of fine screens to the grinding-classifying circuit of a magnetic taconite plant creates a change that effects all components of the circuit. Pine screens in a non-magnetic plant have also been investigated, but here the benefits have not' been as clearly defined. Screens classify according to the particle size. Hydrocyclones classify by a combination of particle size and particle weight. The change in the type of classification minimizes overgrinding of the mineral. The resultant savings in grinding power can be used to increase the throughput, upgrade the product, or increase recovery.

Jan 1, 1971

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

By Fritz F. Prugger

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate co mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province's mines. Fining layouts, materials handling and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1980

By Jie Long, Zijie Liu, Pu Liu, Bo Li, Menghua Li, Qiang Wu

During coal mine operations, roadways may be located close to faults. When designing these roadways, it is important to determine the width of the rock mass between a roadway and a fault area to prevent water inrush. In this paper, the Xintian Coal Mine in the northern Guizhou Province of China is selected as a typical case. Through numerical simulation based on orthogonal tests, range analysis, and multiple linear regression (MLR) analysis, the process of water inrush from faults in excavation roadways is studied. The results show that the influencing factors of the safe width of a rock mass preventing water inrush (RMPWI) can be ranked according to the degree of influence from large to small as follows: the hydraulic pressure of the fault, the surrounding rock grade, the overburden depth of the roadway, the cross-section height, and the dip angle of the fault. Among them, the dip angle of the fault, the cross-section height, and the surrounding rock grade are negatively correlated with the safe width, while hydraulic pressure of fault and overburden depth of roadway are positively correlated with safety width. The predicted value for the safe width based on MLR is greater than the measured value of the width of the RMPWI when water inrush occurs, but less than the calculated value based on the empirical formula in the standard, which proves the accuracy and practicability of the prediction method. This research provides a certain basis and reference for the prevention and control of water inrushes in mines.

Jul 5, 2023

By T. J. DeMull

The business of heap leaching requires accurate forecasting of metal production from the heaps. Business forecasts typically follow a format that project periodic (monthly, quarterly, or annual) product shipments based on anticipated operating results, e. g., tons of ore placed, grade of ore, and rate of leach extraction. Since revenue and cash flow are dependent on the metal production stream, forecasts of metal production are very important for project evaluation and business planning purposes. Nevertheless, production forecasts, particularly for new heap leach projects, have been prone to errors. The present paper identifies some of the pitfalls that would be encountered in preparing production forecasts for new heap leach operations and provides a checklist of considerations to assist in preparing a forecast. Also, the paper presents a case study of copper production forecasting used for the Sanchez Project, a heap leach operation located near Safford, Arizona, that is presently under development by AZCO Mining, Inc.

Jan 1, 1995

By Ing. E. h. Martin Herrenknecht

The paper will describe a number of developments and innovations now in use in microtunnelling machines. These include the use of fuzzy logic steering systems, the proven ability to successfully undertake complex curved microtunnel drives, the ability to complete ultra long drives using microtunnelling techniques, and machines with access to the face of the machine from inside the machine. The ability to tunnel in relatively hard rock utilizing a rock head with back loaded cutters changeable from inside the microtunnel machine and the ability to utilize microtunnel machines in multi modes, such as hard rock mode, “open” mode, EPB mode, and slurry mode with the same base machine again with access to the face of the machine will be described. In addition, the latest computer technology gives the operator “full visualization” of machine functions together with the ability to data log machine operating parameters. Reference will be made to a number of projects worldwide recently completed or under way where these innovations have successfully been utilized.

Jan 1, 1999