Search Documents

By N. C. Gay

The quantitative evaluation of the performance of fill materials placed in gold mine stopes is achieved by (i) measurement of the in-situ load- displacement, or stress-strain, characteristics of the materials; (ii) an objective comparison between the observed fill performance and that predicted from suitable computer modelling techniques; and (iii) objectively comparing conditions in backfilled and conventional stopes. Considerable problems have been experienced with the development of sufficiently robust instrumentation which can be installed within filled pad- docks and give reliable information over a long period of time. However, at most mines where backfill performance is being monitored, it has been possible to correlate stress measurements within the filled paddocks with strain measurements adjacent to the paddocks. The resultant stress-strain curves agree relatively well with those determined in the laboratory. Measurements in the hangingwall strata of filled and unfilled stopes indicate that the placement of fill does reduce the amount of inelastic convergence due to bed separation. Moreover, in some stopes, the rate of convergence with respect to face advance does reduce to that of the theoretical elastic convergence. Quantification of changes in the conditions at the stope face due to placement of fill has proved difficult. Observations indicate that, provided the fill is placed close to the face (- 5 m), and adequate temporary face support is used, conditions in filled panels are superior. In addition, in filled panels the damage caused by a rockburst in the stope and, particularly, in gullies is generally much less than would be expected in an unfilled stope. To quantify these improvements, parameters such as stope height, face advance and the frequency of falls of ground are being monitored.

Jan 1, 1988

By I. Zemanek, A. Rozsypal

Mrazovka tunnel was excavated under one building whose subsurface space was not possible to reinforce against additional settlements induced by digging. In the presented contribution the risk analysis, warning levels and results of deformation measurements are described. Lespace souterrain d‘un des bâtiments sous lequel le tunnel Mrazovka a été creusé n‘a pu être renforcée contre l‘affaissement supplémentaire provoqué par l‘emplacement du tunnel. Le matériel présenté décrit l‘analyse des risques, le niveau des limites et les résultats des mesures des déformations. Der Untergrund eines der Gebäude, unter dem der Tunnel "Mrazovka" ausgeschachtet wurde, war es nicht möglich, gegen nachträgliches Setzen zu versteifen, hervorgerufen durch die Untertunnelung. Im vorliegenden Beitrag sind Gefahrenanalyse, Grenzwerte und Ergebnisse von Deformationsmessungen beschrieben.

Jan 1, 2003

By L. A. Abichequer

ROM grade variability is one of the most important factors influencing plant product recovery. Due to the influence of grade variability on mine profits, it is deemed important to guarantee a proper homogenization of the ore through a well-planned blending and homogenization pile system from which the ore is reclaimed at an acceptable grade fluctuation. This study tests geostatistical simulation efficiency in predicting in situ grade variability. The methodology is illustrated using a data-set from a large phosphate mine in central Brazil. Additionally, real data obtained at the mine site during January and February 2007 were used to derive the actual grades of each pile formed during this period. Each pile was formed by a selection of blocks within a dig line and these lines mined along the year 2007 were also made available. Given the real grades, it was possible to reconciliate and validate the results predicted by the proposed methodology. The main outcome of this study is the opportunity to check the geostatistical simulation as a tool to quantify the variability of the homogenization system.

Jan 1, 2009

By H. B. Prinsloo

Change management and training initiatives in remote rural settings in Africa are generally difficult to implement successfully due to factors such as varying levels of education, multiple nationalities and languages as well as cultures in one workplace. The challenge has always been the ability to implement change management and training initiatives that will have an impact despite these differences. Essentially this requires that the change and training interventions employed are applicable and should work well with a wide range of individuals sitting in one room ? in practice this can vary from semi-literate workers to engineers with PhDs. In this paper we will share the theory behind behaviour-based change management and training and present a case study that reviews an actual supply chain improvement and sustainability implementation at a Zambian copper mine. The case study explains the results achieved as well as the interventions employed to achieve these results in a multidimensional organizational environment. This paper is relevant to delegates who are faced with implementing changes or training in a similar mining environment. Keywords change management, behaviour-based training, learning style, P2P process.

Oct 1, 2013

By T. P. Katakwa

The utilization of software is now inherent to virtually every activity along the mining value chain. However, apart from the software survey done by Gibbs in the 1990s and work on the extent of diffusion of information and communication technology (ICT) in the South African platinum sector by Mugodi and Fleming in 2003, the nature and extent of software utilization in the South African mining industry has never been evaluated. The Mine Planning, Optimisation and Valuation (MPOV) Research Group in the School of Mining Engineering, University of Witwatersrand, therefore initiated a project to collate and analyse the current utilization of software in the South African mining industry. This was done through the development of a web-based database of the relevant software. Snowball sampling was used to collect the data because the South African mining industry is diverse and software utilization is fragmented across and within the sectors of the industry. The data was then organized into distinct categories so that the information from a variety of sources could be evaluated on the same basis. A beta version of the database can be accessed online through a user-friendly front-end platform at http://db.mining.wits.ac.za. The database is expected to help at least 13 educational institutions with decisions on facilities and training that are vital to the education of mining and mining-related professionals. Exploration, mining, and consulting companies will also benefit from information in the database relating to availability and useful combinations of software solutions. The database is also strategic to software providers by providing a better understanding of their respective relative market share along the mining value chain. An analysis of the data collated in this research shows that about 77% of the software users are mining companies, 17% are consulting companies, 3% are mineral exploration companies, and the rest are software providers and educational institutions. The software used in the South African mining industry is largely provided by Gemcom Software International, MineRP Solutions, and MRM Mining Services. CAE Mining, who in 2010 acquired the Datamine Group providing Datamine software, is also widely acknowledged as a major software supplier in South Africa, but data from them had not been obtained at the time of producing the beta version of the database due to proprietary constraints. The work reported in this paper is part of an MSc research study in the School of Mining Engineering at the University of the Witwatersrand. Keywords mine planning, mining, value chain, software, database, South African mining industry, utilization.

Jun 1, 2013

By M. F. G. Bruce

Two backfill systems have been developed on West Driefontein, namely the centrifuge dewatered tailings system and the cyclone-classified tailings system. Modifications to the two systems since the publication of the original paper (Close and Klokow, 1985) are discussed in addition to the results obtained. Considerable experience has been gained from the operation of the centrifuge dewatering units as well as the placement of dewatered tailings in a difficult mine environment. The centrifuge dewatered tailings method has proved successful in the extraction of a highly stressed block of ground at No. 5A Sub-vertical Shaft. The utilization of backfill support in this area made it possible to dispose of a high-grade barrier pillar. This pillar was considered necessary prior to the introduction of backfill support. The recovery of the gold from this pillar made the use of dewatered tailings backfill cost- effective, despite high labour and maintenance costs. Current experience with the bagfilling method of placing cyclone- classified tailings indicates that it is viable and requires considerably less capital investment. Although expensive at present, it is envisaged that costs will decrease once cheaper bags and other forms of stope support are used. The placement of backfill in small-diameter sausage-type bags requires no change in mining cycle and allows the backfill to be placed close to the stope face. Both backfill systems are being expanded but preference is to be given to the cyclone-classified tailings system.

Jan 1, 1988

By J. T. Nel

The Kroll process is the traditional method of producing zirconium metal by reduction of zirconium tetrachloride with magnesium metal. This paper discusses the production of zirconium metal in a plasma reactor. Anhydrous low-hafnium ZrCl4 and Mg metal were fed continuously to a 30 kW non-transfer plasma reactor at a rate of 0.31 kg.h-1. Due to losses in the system the recovery of crude product was 77.5 %. After purification to remove unreacted feed material and MgCl2 by leaching, >98 % pure zirconium metal powder was obtained. The overall recovery of purified Zr was 74 %. The conversion efficiency of the process was 95 %.

Jan 1, 2012

By M. Nakamura, T. Akamatsu

Embankment dams are often constructed on soft rock foundations in Japan, so it is important to precisely predict deformation of the foundations due to fill placement at the design stage. In order to accurately evaluate the settlement and the strain of the rock foundation surface during construction, the influence of the scattering of the deformability of foundations on the deformation behaviour should be investigated. In this paper, a method of evaluating the settlement and the strain of the rock foundation surface during construction was studied with stochastic deformation analysis considering the scattering of the deformability of the dam foundation. Based on the analytical results, a dam foundation design using the deterministic method considering the scattering of its deformability was discussed. Da in Japan Uferdämme of auf weichen Felsfundamenten gebaut werden, ist es wichtig, die Verformung der Fundamente auf Grund der Platzierung der Aufschüttungen bereits in der Planungsphase genau vorherzusagen. Im Zusammenhang mit einer genauen Beurteilung der Senkung sowie der Belastung der Felsfundamentoberfläche während der Bauarbeiten sollte auch der Einfluss der Streuung der Verformbarkeit der Fundamente auf das Verformverhalten untersucht werden. In der vorliegenden Studie wurde die Bewertungsmethode zur der Senkung sowie der Belastung der Felsfundamentoberfläche während der Bauarbeiten mit Hilfe von Wahrscheinlichkeitsanalysen der Verformung unter besonderer Berücksichtigung der Streuung der Verformbarkeit der Dammfundamente untersucht. An Hand dieser analystischen Ergebnisse wurde das Design der Dammfundamente dann enthusiastisch mittels deterministischer Methoden hinsichtlich der Streuung der Verformbarkeit diskutiert. Comme les barrages en remblai sont souvent construits sur des fondations rocheuses tendres au Japon, il est essentiel de prévoir précisément les déformations des fondations causées par la mise en place du remblayage durant la phase de conception. Afin d’évaluer avec exactitude le tassement et la déformation de la surface du rocher de fondation durant la construction, l’effet de la dispersion de la déformabilité des fondations sur le comportement de déformation doit être étudié. Dans cette étude, l’auteur a étudié la méthode d’évaluation du tassement et de la déformation de la surface du rocher de fondation durant la construction en procédant à une analyse aléatoire/stochastique de la déformation et en prenant en considération la dispersion de la déformation des fondations du barrage. En se basant sur les résultats de l’analyse, la conception des fondations de barrage avec la méthode déterministe considérant la dispersion de sa déformabilité a été activement discutée.

Jan 1, 2003

By J. M. Descour, K. Aoki, S. Shirasagi

This paper describes the tunnel seismic reflective survey, which has been developed by the authors in order to detect the geological condition ahead of the tunnel face three-dimensionally using reflected seismic waves. In addition, the applicability and the accuracy of the result of this system has been validated by comparing with the geological observation results at the tunnel face and the result of the drill logging system, which was conducted simultaneously with this survey in order to predict the rock properties using the data acquired during drilling from the tunnel face by rotary percussion drilling. In dieser Arbeit werden Reflektionsseismische Tunneluntersuchtungen beschrieben, die von den Autoren entwickelt wurde, um die geologischen Eigenschaften am Tunnelstirnende dreidimensional an Hand reflektierter seismischer Wellen bei minimaler Unterbrechung der Arbeit zu untersuchen. Darüber hinaus wurde die Anwendbarkeit und Genauigkeit der mit diesem System erhaltenen Ergebnisse durch Vergleiche mit den Ergebnissen geologischer Beobachtungen am Tunnelstirnende sowie den Ergebnissen des Bohrlogsystems bewiesen. Das letztgenannte System wurde gleichzeitig mit dem hier genannten System eingesetzt, um die Gesteinseigenschaften mit Hilfe der Daten vorherzusagen, die beim Bohren von Probelöchern im Tunnelstirnende mit einer Drehschlagbohrmaschine erhalten wurden. Cet article décrit une méthode de prospection sismique de tunnel, développée par les auteurs, pour déterminer en 3 dimensions les conditions géologiques existant derrière le front de taille, au moyen d’étude et de mesure des ondes sismiques réfléchies dans le sous sol, et ce, avec un minimum d’arrêt des travaux d’excavation. En outre, l'applicabilité et l'exactitude des résultats de ce système ont été vérifiées, en comparant les résultats des observations géologiques effectuées au front de taille, avec ceux du log de forage qui a été effectué parallèlement à ce système, en vue de prévoir les propriétés de la roche, grâce aux données collectées au cours du forage d’un trou de sonde depuis le front de taille à l’aide d’une foreuse rotative à percussion.

Jan 1, 2003

By W. Wittke, D. Schröder, H. Polczyk

ABSTRACT: The Urft dam, the Diemel dam and the Eder dam are three old masonry damslocated in Germany. The paper describes the rehabilitation measures and the correspondingstability analyses carried out to adjust the dams to today's standards. Remedial works such as theexcavation of inspection galleries, the installation of a grout curtain with a downstream drainagescreen as well as the installation of pre-stressed permanent tendons were carried out. In all threecases the stability of the upgraded dam could be proven on the basis of finite element analyses. ZUSAMMENFASSUNG: Die Urft-, Diemel- und Edertalsperre sind drei alte deutscheSchwergewichtsmauern aus Bruchsteinmauerwerk. Im Beitrag werden Instandsetzungsmaß-nahmen und Standsicherheitsnachweise beschrieben, die erforderlich waren, um die Staumauernan den heutigen Stand der Technik anzupassen. Hierzu wurden Kontrollgänge aufgefahren,Dichtungsschleier mit luftseitiger Dränage sowie vorgespannte Daueranker hergestellt. In allendrei Fällen konnte unter Berücksichtigung der Instandsetzungsmaßnahmen die Standsicherheit derMauer auf der Grundlage von Berechnungen nach der Methode der finiten Elemente nachgewiesenwerden. RÉSUMÉ: Les barrages de Urft, Diemel et Eder sont trois barrages-poids vieux allemandsconstruit de maçonnerie de moellon. Dans cet article, opérations de remise en état et preuves destabilité sont décrits, qui étaient nécessaires pour adapter les barrages à l'état de la techniqueactuelle. À cet effet, des galeries de contrôle étaient creusés, voiles d'étanchéité avec des drains àla face aval et tirants précontraints permanents étaient fabriqués. Dans tous les trois cas, tenantcompte des opérations de remise en état, la stabilité de la barrage pouvait être prouvée à partir decalculs selon la méthode des éléments finis.

Jan 1, 2003

By M. K. Matthews

The use of backfill has important environmental control implications which, although frequently overlooked, can be both beneficial and problematical. Where backfill is widely used, the reduction in stope heat load and improved air utilization influence the overall mine ventilation and refrigeration requirements significantly. A programme of work examining in detail all the environmental consequences of backfilling is currently underway at the Environmental Engineering Laboratory of the Research Organization of the Chamber of Mines. This paper gives an overview of the work and presents some findings. In so doing, the environmental implications to be considered when backfilling are highlighted.

Jan 1, 1988

By J. O. Claassen

A study was initiated and solutions implemented to address the root causes of a 30%?40% lower than predicted product yield achieved at a Mpumalanga coal mine. A holistic MRTM approach, which focused on improving exploration, geological sampling and analysis, geological modelling, planning, mining, and beneficiation practices, was used. The study indicated that deviations in the planned versus actual yields at the DMS plant were caused mainly by incorrect geological yield predictions, high and variable levels of dilution, and near-dense material, as well as the textural properties of the ore. Keywords MRTM, mining value chain improvement, Witbank coalfields, complex geology.

Oct 1, 2013

By P. Beukes, D. Bessinger, R. Glenewinkel

High titania slag is produced by the smelting of ilmenite and a suitable carbonaceous reductant in electric furnaces. Currently liquid slag is cast into large blocks, which take about 10 days to cool down before they can be crushed, milled and classified into two final products. The two products, chloride and sulphate grade slag, are differentiated according to their size. Granulation of titania slag has been identified as a possible alternative to the conventional block route. This paper discusses some of the work carried out at Exxaro Research and Development to investigate both wet and dry granulation of titania slag.

Jan 1, 2007

By John Taylor

?Introduction to Black Mountain ?Historical metal accounting practice ?Metal accounting audit ?Feed measurement ?Sample precision ?Concentrate measurment ?Current metal accounting practice ?Further refinements to the metal accounting practice

Jan 1, 2005

By C. Pamukcu

In this paper, which is aimed to serve as a review article, first of all a breakdown of the earth?s total water reserves is given. The usage areas of water in the mining industry are mentioned and these uses are briefly outlined, together with the main pollution potential of each. According to this, most of the water (almost 80% of it) is utilized in processing. Later on, probable damages that the mining would give to groundwater as a result of acid mine drainage, heavy metal pollution, euthrophication and deoxygenation is described. Finally, the measures and controls that should be taken against water contamination in mines are presented.

Jan 1, 2008

By Mike Stanley

This is a case study of an opencast coal mining operation where the physical and financial performance was improved via applying a process of transformational leadership development. [ ]

Jan 1, 2008

By B. Steyn

AngloGold Ashanti?s Obuasi Mine, in Ashanti Province, Ghana, operates a plant utilizing bacterial oxidation technology. The mineralization consists predominately of arsenopyrite with gold associated in the sulphides. The plant was commissioned in 1994, at that time was the largest BIOX® plant in the world, and has been operated by AngloGold Ashanti since 2004. The constraints identified in the plantwere the flotation capacity, BIOX® feed size and disruptions to the BIOX® process. This paper focuses on the practical steps that were followed in order to increase the recovery of the plant. The original plant design was based on a head grade of 10 g/t and an overall recovery of 86.5%. In 2007 the plant was operating at an overall recovery of 79.2% at a head grade of 5.6 g/t and this has improved to 80.6% at a head grade of 5.8 g/t during the last quarter of 2008. Additional improvement to 81.5% are expected by the end of April 2009. Improvements that have been implemented include: ?Replacement of the regrind mill ?Installation of additional float capacity ?Installation of a scavenging circuit ?Installation of a complete water treatment plant. In addition we have focused on the effect of the water circuit on the BIOX® process and the steps involved in correcting this problem. The water circuit was originally designed as an open circuit and through environmental considerations the circuit was closed towards the end of 2007. The bacteria in the BIOX® are particularly sensitive to cyanide and cannot tolerate levels above 0.05ppm (free cyanide), this required extensive modifications to the water circuit. The plant improvement project is ongoing and the current scope of work should be complete by the end of April 2009. Further research and development work is being planned, which includes a ?white rot bacteria? that can consume the preg-robbing carbon and oxidize the sulphide in a single pass.

Jan 1, 2009

Nowadays, fully encapsulated rockbolts have become a key element in the design of ground control systems. The main reason is that they offer high axial resistance to bed separation. In this research, the load transfer capacity of a fully grouted bolt is evaluated analytically in an elastoplastic rock mass condition. The research considered the effect of bolt end-plate on load transfer capacity. Bolt and surrounding materials were assumed to be elastic and elastoplastic materials respectively. The load transfer mechanism of a fully grouted bolt is a function of parameters such as bolt length, shear stiffness of interfaces, in situ stress, presence of face-plate and distance along the bolt. These factors were analytically evaluated. Finally, the load along the bolt was predicted in different surrounding rock mass characteristics.

Jan 1, 2011

By H. Sasao, Y. Obara, A. Hirata

In the upper part of the planned location of the portal of a highway tunnel, there was a steep rock cliff with several unstable rock blocks. It seemed that the risk of those rock blocks to fall was very high. The cut-out to stabilize the rock cliff was monitored with various measuring instruments to prevent the sudden fall of the rock blocks. This paper discusses the measurement of acoustic emission and interpretation of its result during excavation of the rock cliff. We calculated displacements by integrating the accelerogram twice in terms of time, and demonstrated that slight displacements can be calculated from the measured AEs. Dans la partie supérieure de l’emplacement prévu pour le portail d’un tunnel autoroutier, il y avait un escarpement rocheux raide avec plusieurs blocs rocheux instables. Le risque de chute de ces blocs semblait très élevé. Lors de la coupe pour stabiliser l’escarpement rocheux, le suivi a été effectué avec différents instruments de mesure pour éviter la chute brutale des blocs rocheux. Cette thèse présente les mesures d’émission acoustique (EA) et l’interprétation de leurs résultats pendant l’excavation de l’escarpement rocheux. Nous avons calculé des déplacements en intégrant l’accélérogramme deux fois par rapport au temps, et montré que de petits déplacements sont calculables à partir des EA mesurées. Im oberen Teil des geplanten Ortes des Stollenmundes eines Autobahntunnels gab es einen steilen Felsen mit mehreren instabilen Felsenblöcken. Die Gefahr schien sehr groß zu sein, dass diese Felsenblöcke einstürzen können. Beim Abbau um die Stabilisierung des Felsens wurde das Monitoring mit verschiedenen Messinstrumenten zusammengestellt, um den plötzlichen Verfall der Felsenblöcke zu verhindern. Das vorliegende Papier diskutiert die Akustische Emission und die Auslegung deren Ergebnisse während des Abbaus des Felsens. Wir berechneten die Verschiebungen durch zweimalige Integrierung der Accelerogrammen in Bezug auf die Zeit. Die dargestellten kleinen Verschiebungen können aus den gemessten akustischen Emissionen berechnet werden.

Jan 1, 2003

By R. Tabanrad

This article examines the stability analysis of intake tunnels of Karun III dam & power plant. The tunnels have been excavated with a 3-dimensional and fairly complicated geometry in Pabdeh weak formation rocks at Zagros region. Due to the particular excavation geometry and inapplicability of plane-strain status, the stability of these excavations has been analyzed using both the 3D elastic software Examine 3D and the 2D non-elastic software UDEC simultaneously. The geomechanical parameters have been estimated by back analyzing the measured displacements from instruments, which were installed in the tunnels, and the parameters have been used in non-elastic numerical model. The results of the analysis show that the strains occurred in surrounding rock mass are less than the allowable failure strain and that the tunnels are stable. In addition, considering the results of non-elastic 2D analysis, the areas with unstable potentiality were identified and after the instability occurred at the areas predicted by the model , it was stopped up to the allowable strain limit through installing additional support . Bei diesem Artikel handelt es sich um eine Analyse der Festigkeit der Eingangstunnel des Damms und Elektrizitätswerks “Karoon III”.Die Tunnel haben drei Dimensionen und eine sehr schwierige Form und sind in brüchigen Felsen in “Pabedeh ,in Zagrossgebirge”eingebohrt.Aufgrund besonderer Form der Bohrung wurde ihre Festigkeit durch elastische dreidimensionale Soft-ware analysiert,die gleichzeitig die drei-und zweidimensionale unelastische Soft-ware UDEC benutzt hat.Die geometrische Parameter sind mit Ausnützung der Analyse berechneter eingesetzter Versorgungen,die in Tunnel aufgebaut sind,bewertet.Und diese Parameter sind in Zahlen-Analyse benutzt.Die Ergebnisse dieser Analyse zeigen,dass die Drücke an Felsen weniger als problematischer Grad der Drücke sind und die Tunnel fest sind.Ausserdem wurde mit einem Einblick auf die Ergebnisse der unelastischen zweidimensionale Analyse die eventuellen unfesten Teile bestimmt.Nach entstandener Unfestigkeit an diesen Teilen wurde die problematischeDrücke für Aufbau mehrere Anlagen gestoppt. Cet article examine l'analyse de la stabilité de tunnels de la prise de Karoun barrage III et centrale électrique. Les tunnels ont été excavés avec une 3 dimensionnel et compliqué géométrie dans Pabedeh que la formation faible balance à région Zagros équitablement. Dû à la géométrie de l'excavation particulière et inapplicabilite de statut de tension plane, la stabilité de ces excavations a été analysée en utilisant les deux le 3D logiciel élastique Examen 3D et le 2D logiciel non - élastique UDEC simultanément. Les paramètres du geomechanical ont été estimés en analysant le déplacement mesuré d'instruments qui ont été installés dans les tunnels et les paramètres en arrière a été utilisé dans les modèles numériques non - élastique. Les résultats de l'analyse montrent que les tensions se sont produites dans masse du roc environnante est plus petit que la tension de l'échec admissible et que les tunnels sont stables. De plus, les régions avec potentialité instable ont été identifiées étant donné les résultats de 2D analyse non - élastique, et après que l'instabilité se soit produite aux régions prédites par le modèle, il a été arrêté jusqu'à la limite de la tension admissible à travers installer du support supplémentaire.

Jan 1, 2003