Search Documents

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magneto-hydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2014

By S. C. Essack

"Tenova Pyromet has designed a slag flow control valve that throttles the flow of slag in order to control the tapping rate. In addition, the valve has proved to be a reliable tool for closing the furnace during normal operation as well as emergency conditions. The valve makes use of a water-cooled copper element that is hydraulically operated and attached directly to the slag tap-hole. The equipment is compact, simple to maintain, and cost-effective to purchase and install. It can be retrofitted to most existing slag tapholes with minimal modifications.During the development phase, finite element method (FEM) and computational fluid dynamics (CFD) software was extensively used to model predicted operating conditions and to optimize the design. By using CFD, it was possible to understand the flow patterns inside the copper and to optimize these to improve overall performance.The slag valve was installed and commissioned in 2011/2012 on a 12 MW furnace as part of a new mineral wool plant in the USA. It has performed well since its installation despite operating under conditions in excess of the original design criteria. During the first 6 months of operation it quickly became the preferred method of closing the furnace, although the design intent was for occasional use during emergency shutdown conditions only. Since replacing the mudgun as the main method of closing the tap-hole, a few minor changes have been made to the installation in order to cope with the increased heat load and much higher frequency of use."

Jan 1, 2014

By P. G. H. Pistorius, D. S. Konadu, G. Lubbe

The aim of this investigation was to determine whether the composition of a shielded-metal arc-welding electrode coating affected the low-temperature impact toughness of austenitic stainless-steel weld metal. It is generally accepted that increases in the δ-ferrite and nitrogen contents result in a decrease in toughness at low temperatures. Weld metal from electrodes with a basic coating also generally exhibit better toughness than those from rutile (acidic) electrodes. An increase in basicity was expected to decrease the number and size of inclusions, which in turn provides a tougher weld metal. Three commonly available potassium–rutile E308L electrodes were used, complying with the E308L-16 and E308L-17 specifications. Analysis of the electrode coatings showed very similar chemistry and basicity. Significant differences in the inclusion contents of the weld metals were observed: the E308L-17 weld metal had a lower inclusion content (1.4% by volume) than the E308L-16 weld metal (3.7%). The former had higher impact toughness at all temperatures, despite a slightly higher nitrogen content. Regression analysis confirmed that the inclusion content had a significant effect on the impact toughness at all temperatures.

Jul 2, 2022

By G. J. de Korte

South Africa is reliant on coal for the generation of almost all the electricity used in the country, and several large industrial concerns such as Sasol are also coal based. Research relating to the mining, beneficiation and utilization of coal is important in order to ensure the optimal exploitation and use of coal within the country. The Fuel Research Institute (FRI) of South Africa was established in 1930 to investigate all aspects of coal beneficiation and utilization in South Africa. The FRI went on to conduct world-class research and in 1957 a pilot coal preparation plant was constructed in Pretoria to enable large-scale practical experimentation. The pilot plant played a pivotal role in the establishment of South Africa?s low ash coal export project. Political and economic factors contributed to the eventual closure of the FRI and South Africa experienced a period of about 10 years between 1990 and 1999 during which very little public coal preparation research was done. This changed for the better towards the end of 1999 when Coaltech 2020, a collaborative research program was established. Participants included the CSIR, universities, the government and the major coal producers. Coal preparation research conducted under Coaltech thus far include dewatering and drying of fine coal, size classification of ultra-fine coal and dense-medium fine coal beneficiation. Currently, the Coaltech focus is on the beneficiation of low-grade coal reserves and is investigating existing as well as new techniques that can be utilized to provide cost-effective beneficiation of low-grade raw coals and reject coals.

Jan 1, 2010

By Daniel W. Kappes, Pierre F. X. Mousset-Jones

"In this paper a discussion is presented of a program designed to produce a 40-day production forecast for an underground stoping system.The program is intended to be a tool for the operations department in an underground mine, and is designed to utilize data readily available from production reports. Brevity of data input, ability to revise slope conditions easily and the accuracy of starting stope status are stressed. Applicability of the program to a wide variety of sloping methods makes the program potentially useful in a large number of mines.The general functions of the program subroutines, and input and output lists are discussed. An example is also given of a stope in operation for a three-day period, which shows how the program can handle production irregularities as they arise."

Jan 1, 2014

By R. L. Castro

Currently, in several caving operations, the spacing between the drawpoints is determined by consulting Laubscher's design guide (Laubscher 1994, 2000), a methodology based on the gravity flow characteristics of the caved rock. Laubscher's methodology is based upon the height of interaction between adjacent flow zones, but does not allow calculation of primary recovery for a given layout. In this paper the authors present a technical and economic methodology based on the flow that occurs near the drawpoint and the associated development costs to estimate the optimal spacing. The flow model at the drawpoint was validated at the El Teniente mine, which extracts coarse caved rock. To validate the flow model, small-scale simulations using drawpoint clusters were conducted and results compared to extracted grades, marker recovery, and drill holes to determine ore remnants that are part of the production control programme at the mine. The results indicate that primary recovery depends on the height of interaction, which varies with the friction angle of the caved rock and the spacing between adjacent drawpoints. Primary recovery estimations indicate values from 85 per cent to 97 per cent depending on the drawpoint spacing used. Extrapolations were then conducted to estimate the primary recovery for different drawpoint configurations planned to be used in the New Mine Level of the mine. The results indicate that the optimal drawpoint spacing is 32 m x 20 m with a through length of 18 m. The methodology developed may be used to estimate optimal drawpoint spacing for block caving mines under different metal prices and mine cost conditions.

Jan 1, 2012

Council and Standing Committees - 1983/84 President: Prof. R.P. King Vice Presidents: J.D. Austin and H.E. James Honorary Treasurer: Prof. D.G. Krige Immediate Past President: Prof A.N. Brown Members of Council: B.C. Alberts, Prof. S. Budavari, N.J. Devine, Dr C.J. Fauconnier, P.T. Fewell, C. E. Fivaz, J. S. Freer, Prof. G.G. Garrett, J.J. Geldenhuys, Dr A.K. Haines, Dr B.K. Loveday, G. Pienaar, B.E. Protheroe, Dr O.K.H. Steffen, G.C. Thompson, Dr H. Wagner, Dr P.T. Wedepohl Chairman, Witbank/Middelburg Branch: H.C. van Zyl Chairman, Orange Free State/Klerksdorp Branch: D.A. Parfitt Past Presidents Serving on Council: Dr M.G. Atmore, Dr J.P. Hugo, Dr P.R. Jochens, Prof. R.P. Plewman, G.Y. Nisbet, Dr R.E. Robinson, Prof. M.D.G. Salamon, P.W.J. van Rensburg, D.A. Viljoen, P.A. von Wielligh Standing Committee Chairmen: Adjudication, Prof. A.N. Brown; Awards, Prof. A.N. Brown; Banquets, J.S. Freer; Constitution, Rules and Policy, Prof. A.N. Brown; Excur¬sions, J.S. Freer; Journal, H.E. James; Membership, H.E. James; Phoenix National Committee, Dr M.G. Atmore; SAIMM School - Extractive Metallurgy, Dr A. K. Haines; SAIMM School - Mining, Dr H. Wagner; Special Publica¬tions, J.D. Austin; Technical Programme - Extractive Metallurgy, Dr B.K. Loveday; Technical Programme - Mining, G. C. Thompson; Technical Programme -Physical Metallurgy, G. Pienaar; Training, Career Guidance and Education, Dr M.G. Atmore; World Mining Congress - National Committee, Prof. R.P. Plewman; Working Group Physical Metallurgy, Prof. G.G. Garrett

Jan 1, 1984

By J. L. Porter

This paper takes a personal look, through the author?s own experiences, at the implementation of innovations in the narrow-seam, hard-rock mining environment of South Africa?s mining industry over the past 40 years. A number of examples are used to illustrate some of the successes and failures over this period. More importantly, the examples are used to illustrate that the bulk of the investment for these projects should have been applied in a manner that could have achieved more sustainable results. The use of the word ?technology? in this context is also examined, as it is the author?s contention that only measuring the performance of machinery fails to encapsulate the potential of the entire system describing the scope of the innovation being implemented. These experiences and observations are projected onto the current backdrop of upheaval in the relationship between key industry stakeholders and the sustainability challenges facing areas of the mining sector in the South African economy. The paper concludes with some opinions on where attention can be focused in order to develop new thinking that can be applied for the safe and economic extraction of the nation?s mineral wealth.

Jan 1, 2014

By E. L. Forner, G. M. Miller, J. Scheepers, A. J. du Toit

"The sizing, designing, and costing of copper electrowinning circuits requires an in-depth understanding of the fundamental relationships between circuit parameters and the practical operation requirements. The aim of this investigation was to optimize total copper electrowinning project cost by mapping the operating limits of key mechanical equipment. The model was compiled by mapping various cellhouse layouts in terms of number of cathodes per cell, crane productivity, stripping machine productivity, and rectifier–transformer (rectiformer) sizing using data tables for sensitivity analysis. These parameters were then collated and evaluated on a cost by size basis. The model provides an optimum band of operation for cellhouse productivity and project capital cost for a typical range of production throughputs, from 10 kt/a to 200 kt/a cathode copper. The information may be used as a high-level selection guide to assist with identifying a costeffective copper electrowinning circuit design for a specific production rate. The data was validated and compared with existing copper electrowinning cellhouses around the world that typically install no more than 84 cathodes per cell. IntroductionThe sizing, designing, and costing of copper electrowinning (EW) circuits require an indepth understanding of the fundamental parameters as well as the practical requirements to optimize cellhouse productivity and capital cost. Although a significant amount of work has been done designing new copper electrowinning circuits, an in-depth evaluation of world operating data reveals that the number of cathodes per cell, which affects cellhouse layout and productivity, is not consistent for a specific production rate (Anderson et al., 2009; Robinson et al., 2003, 2013). Based on this premise, Kafumbila (2017) suggested that there are unanswered questions, such as ‘why are the numbers of cathodes per cell different for copper production rates of 20 kt/a and 40 kt/a?’In this paper, data tables are employed to map the operating limits and costs of key Cu EW equipment. An overall Cu EW project cost map is then compiled by collating optimum cellhouse layout (number of cathodes per cell), optimum crane productivity, optimum"

Nov 1, 2018

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

By A. van den Berg

Mining of sand in South Africa is rapidly growing to sustain an increasing demand for sand for building purposes. Although mining of sand is regulated by environmental legislation, such as the National Environmental Management Act 107 of 19981, previous bad mining practices have left areas of land degraded and vulnerable to erosion. This study was conducted in the Seringveld Conservancy, where mining of sand has left the landscape with a degraded and unsightly appearance, and where little rehabilitation of the original vegetation has taken place. The aim of the study was to develop rehabilitation techniques for the degraded mined soils on two sand mines, Boekenhout Sand and Krokodil Sand, and to develop an overall strategy of revegetation by regenerating key plant species. Techniques for regenerating indigenous tree species cover, using modified mined sludge if topsoil is not available, were used to develop a practical and cost-effective strategy to be used in revegetation. A comparative trial was used to cultivate indigenous tree species in different soil mixtures. The study is important as it provides new information on the rehabilitation and revegetation of sand mined areas in the Seringveld Conservancy. This study will determine if alternatives could be used to replace topsoil on mined areas where none is available. The study is needed to determine whether revegetation of the mined areas would be possible using indigenous plant species that are difficult to grow. The overall results indicate that replacing topsoil was successful for various modified soil mixtures that could sustain the growth of indigenous vegetation on the sand mines. Different indigenous tree species require different modified soil mixtures for successful propagation. A revegetation strategy was developed to complement and enable the rehabilitation of the mined areas in the Seringveld Conservancy. Keywords Rehabilitation, revegetation, Seringveld, sand mines, Burkea africana, topsoil, germination trials.

Jan 1, 2011

"Sampling error and bias, especially the Increment Preparation Error (IPE), are introduced when the tool allocated to do the job fails to extract a representative sample. This is the case with chip sampling; the tool can only extract haphazard shapes of loose or fractured material and not always from within the demarcated sample area. Increment Extraction Error (IEE) and Increment Delimitation Error (IDE) could be severe, but are found to be relatively unbiased. The uncontrolled action of the sampler in discarding excess sample material after sample collection has a significant impact on the error and bias introduced with each and every extraction. A new type of bias, referred to as the ‘waste discard bias’, arises when samplers select what portion of the excess sample material to discard at the sample site. Material visually identified as waste is discarded in preference to mineralized broken ore if there is an excess of sample material. This results in a considerable error in the analytical results. The bias is proportional to the reef-waste ratio in the demarcated sample. IntroductionTwo types of ‘sampling’ are distinguished, namely sampling of particulate materials (broken ores) and sampling of solid, unbroken in situ mineralized reef. This study considers only chip- or face-sampling of in situ, goldbearing, carbon-rich conglomerates typical of the Upper Witwatersrand Supergroup and examines where components of sampling error and bias, clearly specified in the Theory of Sampling, may arise during the practice of ‘face sampling’. Many millions of face samples have been extracted from Witwatersrand-type mines using a hammer and chisel, and detailed descriptions (standard operating procedures) of how the samples should be taken have been developed by many mining companies. There is, however, no taxonomy or nomenclature for managing or reporting the different types of errors associated with chip sampling. The Theory of Sampling compiled by Pierre Gy in the early 1950s provides, comprehensive nomenclature of sampling errors that is applied to particulate sampling of ore in a lot, a stockpile, or a moving stream on a conveyor belt. The taxonomy and characteristics of sampling errors, grouped according to the sources from which they arise, and identified by Gy (1973, 1979, 1982, 1992, 1995, and 1998) are shown in Figure 1. This classification of errors is used extensively in regard to the sampling of particulate materials in the mining and minerals industry, but not in regard to chip sampling. A relatively small mass (hundreds of grams) of representative particulate material for estimating the average grade of a much larger mass (thousands of tons – the ‘lot’ in the Theory of Sampling) is extracted by the chipping or cutting of a representative rock ‘sample’ from the stope face."

Jan 1, 2016

By N Morales, G Nelis

Short-term plans must meet the long-term goals while accounting for shovel selectivity, operational space, and scheduling restrictions. There are several approaches that deal with these issues to deliver a feasible short-term schedule. This paper compares two approaches based on mathematical programming to address the short-term mining cut definition and scheduling in an integrated way. They work by scheduling extraction to comply with long-term production goals, but they differ in how mining cuts are modelled. The first approach schedules Selective Mining Units (SMUs) but aggregates them around predefined locations. The second approach does not work on SMUs; it decides directly what mining cuts are to be used from a pre-defined set of shapes. It assigns a destination and schedules the extraction for the selected mining cuts. We applied both approaches in a real case study to compare their results in terms of profit, mining cut design, expertise needed, profit, and optimisation performance.

Sep 1, 2021

Edward J. Stephenson. Extractive metallurgy. Recent advances. Park Ridge (New Jersey), Noyes Data Corporation. James L. McCall and P. M. French (eds.). Interpretive techniques for microstructural analysis. 1977. Institution of Mining and Metallurgy. Prospecting in areas of glaciated terrain. London, the Institution, 1977. £16 ($D.S. 30). NIM reports Report no. 1928 A liquid-nitrogen monitor for lithium-drifted germanium detectors. (21st Nov., 1977). Report no. 1931 The equilibrium between the slag and the metal in the production of low-carbon ferromanganese. (14th Nov., 1977). Report no. 1934 The spectrometric analysis of chromium-bearing materials with particular reference to ferrochromium slags and chromite ores. (30th Nov., 1977). Report no. 1935 The construction and testing of a small mixer-settler for use in the laboratory. (30th Nov., 1977). Report no. 1933 The determination of trace elements by thin-film X-rayfluorescence spectrometry, and its application to zirconium. (30th Nov. 1977). Report no. 1942 The accuracy of assays for platinum -group metals and gold. (30th Nov., 1977). Courses on geostatistics In view of the continuing demand, the University of Leeds will offer two further courses on geostatistics in 1978, each covering ten working days (3rd to 14th April, and 3rd to 14th July).

Jan 1, 1978

By B. Yu, M-H. Cao, C. Zhou, X-Z. Zhang

The transient infiltration and lubrication behaviour of slag during continuous casting of steel is important for billet quality. A two-dimensional coupled mathematical mould model was developed to investigate these phenomena. The accuracy of the model was verified by comparing the calculated slag consumption with measurements by the plant. The results show that the liquid slag is consumed from the middle and late period of positive strip time to the next early period of positive strip time, including the entire negative strip time. The maximum downward infiltration velocity and positive pressure in the slag channel is at the middle of the negative strip time. Increasing the positive pressure of the slag channel is conducive to lubrication. The shear stresses acting on the shell surface and at the mould side were determined by the lubrication slag consumption and total slag consumption, respectively, and gradually decreased with increasing slag consumption. The negative strip time was lengthened to increase the slag consumption and prolong the time near the maximum downward shear stress, so as to be conducive to the demould.

Apr 16, 2024

Primary roof support represents the first line of defence against rockrelated falls of ground in underground mines, and improper utilization or misunderstanding of the applicability and behaviour of primary support can be costly from a safety standpoint. This is a major concern for underground mines, as roof support is the single most costly expense from a mining operational perspective. This is further backed by the evidence that, in the USA, hundreds of injuries and fatalities still occur each year because of rib, roof, and massive roof falls. Additionally, the fully-grouted passive rebar, fully-grouted tension rebar, and resin-assisted mechanical anchor bolts, which constitute a large portion (89%) of the 68 million bolts installed each year in underground mines in the USA can vary in cost quite dramatically. To mitigate this concern a study was conducted in 2010 by the National Institute of Occupational Safety and Health, in conjunction with Southern Illinois University of Carbondale, to assess the performance of primary roofbolts in underground coal mines for improved safety and cost. This was accomplished using underground roofbolt monitoring solutions, field data, and numerical modelling to better understand the quasi-static behaviour of underground coal mine roofs and the response behaviour of the bolts. In particular, over 170 instrumented extensometers, closure meters, shear meters, fully-grouted passive rebar, fully-grouted tension rebar, and resin-assisted mechanical roofbolts were installed at three coal mines across the USA. Of these three mines, two used the room and pillar extraction method and the other used the longwall extraction method. There was no evidence to indicate a difference in performance of the active primary roofbolts compared with the passive primary roofbolts. Additionally, in the initial loading phase, the active bolts showed no difference in loading, indicating that tension bleed-off is of more of a concern than originally thought. Lastly, for the initial computer modelling studies, challenges still remain in obtaining a good match to the in situ bolt measurements and replicating the discontinuous roof rock and in situ bolt behaviour over time.

Jan 1, 2014

By A. Ndibalema

Blasting is one of the primary functions in any mining operation. Despite the fact that it generally constitutes between 30% to 40% of the mining cost, blasting also affects the cost-effectiveness of down steam activities such as load and haul, safety, tyre life for haul trucks, crushing and milling. Over the past three decades, significant progress has been made in the development of new technology in an attempt to reduce costs and increase efficiencies and productivities of blasting activities. Mine to mill project concepts have paved the way for such developments. Other advancements have included sophisticated computer modelling technologies for blast design and performance analysis. There are many factors that affect the cost of blasting. These can be divided into two categories; controllable and uncontrollable. The latter includes costs related to depreciation, exchange rates and government legislation with the former category including contractor versus owner blasting costs, efficiency and productivity issues and product quality. Controllable factors have one common denominator which can determine their outcome; direct site management influence. Excavator digging rates and final floor conditions give a good measure of blasting performance, and alternatively cost effectiveness. This paper is aimed at benchmarking against a blast optimisation database, understanding the relationship between costs and identifying opportunities for improvement. Understanding the cost drivers allowed a typical cost model to be developed for the current mining operation at Geita and this was used to drive continuous improvement with emphasis on closing the information loop.

Jan 1, 2008

By S. G. Mgenge, J. D. Steenkamp

Tronox Namakwa Sands operates two ilmenite smelters for the production of high-titania slag and low-manganese pig iron. Slag or metal is tapped from one of two product-specific, bi-level tap-holes. In this paper the refractory design specific to the tap-hole refractory layout is described, as well as practices for slag and metal tapping and refractory maintenance. Further developments planned are briefly described.

Jan 1, 2014

YEAR 1943-1944 Vol. 44 Page A major change-over in the ventilation of a deep level mine, by F. G. Hill and E. C. Ranson, 27; Discussion 56, 62, 67, 71, 72, 79, 123, 129 131 A note on the quarrying of surface limestone in the Sinai Desert, by V. L. Bosazza.. .. 59 Mining with diamond drills at the Nkana Mine of the Rhokana Corporation, Limited, Northern Rhodesia, by W. A. Odgers and A. G. Stirling, 95; Discussion 117, 121, 122 123 On silicates and dusts from the Witwatersrand gold mines (some preliminary notes), by J. J. Frankel, 169; Discussion .. 178 Presidential Address-Review of the rock pressure problem, by C. Biccard Jeppe, 3; Discussion 11,15 17 The chemistry, production and application of plastics, by P. N. Lategan, 138; Discussion 151 153 YEAR 1944-1945 Vol. 45 Page A microtechnique for the size-grading of mine dust, by S. R. Rabson, 34; Discussion 49, 50, 52 55 Activated carbon for regenerating used lubricating oil, by F. J. Tromp and J. J. Matthee 90 A contribution to the study of the production of zeolites, by C. C. le Grange and A. J. Petrick 235 A laboratory method for the determination of the suitability of South African coal and coal blends for the manufacture of metallurgical coke, by R. F. J. Teichmann .. .. 202 Copper containing cements for self-sanitising surfaces, by R. S. Young and H. L. Talbot 156 Notes on some sulphide minerals from the Far East Rand, by E. Mendelssohn, 84; Discussion, 88 89 Presidential Address-A review of underground support on the Witwatersrand with its Bearing on the Problem of ultradeep mining, by P. J. Louis Bok, 3; Discussion, 24, 25 27 Scientific management with particular application to a Witwatersrand gold mine, by J. S. Ford, 63; Discussion, 77, 80, 82 83 Some aspects of rock-drilling practice (the Witwatersrand gold field), by C. J. Irving, 163; Discussion, 185, 190 *197 Temperature measurements in a mine on the Witwatersrand with an electrical resistance thermometer, by O. Weiss, 127; Discussion, 136 137 The measurement of the geo-thermic gradient by means of the clinical thermometer, by R. A. H. Flugge-de Smidt, 105; Discussion, 136 137 The micro-chemical determination of free and combined silica in mine dust, by S. R. Rabson, 43; Discussion, 49, 50, 52 55 The oxidation of pyrites associated with South African coals, by R. F. J. Teichmann 141 YEAR 1945-1946 Vol. 46 Page Air cooling plant, No. 4 Shaft, City Deep, Limited. A review of layout and results achieved, by H. W. Unwin, A. Malcolm and R. E. Campbell Pitt, 66; Discussion, 100, 102, 103, 106, 110 115 A preliminary note on the Waterberg coal field as a possible source of coking coal, by P. E. Hall 124

By J. T. M. Amphlett, C. A. Sharrad, M. D. Ogden, R. I. Foster

"A renewed interest in nuclear power around the world in order to reduce greenhouse gas emissions is going to increase demand for uranium as fuel. This will result in more uranium being mined, which will in turn increase associated environmental pressures, such as fresh water use. A move to lower quality waters containing impurities such as chloride would help alleviate these pressures. In this work, we determined the uptake characteristics of weakly basic anion exchange resin Ps-EDA towards uranium from saline solutions in a dynamic flow column. Breakthrough curves were produced, with suppression of uptake being observed for chloride concentrations above 5 g L-1. Calculated resin saturation capacities at zero and 5 g L-1 chloride are comparable with literature values for strong-base anion exchange resins, and exceed those published for weak-base resins up to 20 g L-1 chloride. Data has been fitted to multiple breakthrough models, with the modified dose-response model most effectively predicting uranium recovery. The results show that the ethylenediamine functionality could be suitable for use in future uranium processing flow sheets where a high-saline lixiviant is used. IntroductionIon exchange (IX) is a key technology in the uranium mining industry and is well established for the extraction of uranium from both acidic and alkaline leach liquors (Edwards and Oliver, 2000). It was first employed in 1952 at the West Rand mine in South Africa (Ford, 1993; Taylor, 2016). H2SO4 and Na2CO3 are the most commonly employed lixiviants used to solubilize uranium in acidic and alkaline leach conditions respectively. The chemistry of these systems causes uranium to form anionic sulphate or carbonate complexes, which can be taken advantage of by anion exchange resins.Another major technology for the extraction and purification of uranium from leach liquors is solvent extraction (SX). This technique involves the extraction of uranium from the aqueous phase into an immiscible organic layer. Although this is a commonly used method, there are major drawbacks to it, including the use of large volumes of flammable solvents, solvent loss, phase disengagement, third phase formation, and the production of problematic degradation products (Veliscek-Carolan, 2016). These problems can be circumvented through the use of IX resins."

Dec 1, 2018