Search Documents

To provide a method for locating trapped miners promptly and accurately. The Approach: Develop a wireless emergency system that is intrinsically safe, compact, easy to operate, reliable, sturdy, and economical. How It Works: A (one transmitter has been developed under Bureau of Mines contracts. The transmitter weighs only a few ounces, is powered by a cap lamp battery, arid can be carried on the miner's belt. A compact loop antenna, which could either be carried by the miner or strategically located in the mine, is used to generate a magnetic field that is sensed by a mobile receiver on the surface. When needed, the antenna is deployed to form a single loop. In mines where the overburden is less than 600 feet, a loop of No. 19 wire approximately 30 feet in circumference is normally adequate. This antenna weighs less than one half pound. In deeper mines, a heavier wire and bigger loop is required; a No. 10 wire deployed around a pillar has been used.

Jan 1, 1974

By J. M. Stuve

This Bureau of Mines investigation measured the low-temperature heat capacities of FeOC1(c) and FeC13(c) in the temperature ranges of 6 to 305 K and 4.6 to 300 K, respectively. The standard entropies (S°, 298.15 K) of FeOCl(c) and FeC13(c) were derived as 19.73±0.03 cal/deg-mole and 35.33±0.07 cal/deg-mole. A large lambda transition was observed in the heat capacity of FeC13(c) at 8.4 K. The standard enthalpy of formation (?H°f, 298.15 K) of FeOC1(c) was determined to be -98.23±0.22 kcal/mole by HC1 solution calorimetry. High-temperature enthalpy measurements (H-H298.15) of FeOC1(c) were determined to 700 K by precision drop calorimetry. Standard thermodynamic formation data and related functions were tabulated at various temperatures for FeOC1(c) and FeC13(c).

Jan 1, 1980

To rapidly and dependably locate shorts and opens in mining equipment power cables. Approach: The approximate locations of faults are found using a sound pulse echo, then the faults are exactly located with one of two probes. How It Works: To approximately locate u fault in shielded or unshielded cable, the cable is disconnected from the mine power center, and connected to the sound pulse generator. The generator is also connected to the ground conductor of the cable. When the generator is energized, electrical pulses are transmitted, and each moves along the conductor until it reaches a fault. When a pulse reaches the fault an echo returns to the instrument, either a positive pulse if the fault is an open, or a negative pulse if the fault is a short. See Figure 1. The further along the cable the first fault is from the instrument, the longer it takes for the echo to return. The instrument automatically measures the time and calculates the distance. The distance in feet is shown on an illuminated digital display.

Jan 1, 1976

By J. C. Edwards, C. C. Hwang

In the design for a fire or smoke emergency, a main concern is maintaining an evacuation path that is free of smoke and hot gases. In ventilated tunnel fires, smoke and hot gases may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of the reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels, and building corridors. In the present study, a computational fluid dynamics (CFD) program is used as a design tool to model floor-level fires in a ventilated tunnel. The fire is simulated by a diffusion flame of propane issuing from a circular hole on the tunnel floor. The computed profiles of velocity and temperature along channel cross sections are similar to those obtained experimentally. The computed reverse-flow layer length has been correlated with a densimatric Froude number with some success. A non-dimensional parameter involving the source fire intensity is also used for the correlation. These analyses show that an appropriate ventilation air current must be maintained to provide an evacuation path from the source fire clear of smoke and hot gases. It is believed that CFD modeling, employed correctly and interpreted carefully, can be a useful design tool for fire protection.

By J. E. Emmerling

The Federal Bureau of Mines investigated dust suppression obtained with three different water-spray nozzle systems during underground continuous coal mining at the face. The nozzles were the "regular" nozzle normally used by the mine, and high-efficiency and low-efficiency nozzles selected on the basis of an airborne capture theory of respirable dust by spray drops. The high-efficiency nozzle used one-third less water than the others throughout the testing. Results depended on the type of cutting operation at the face. The sump-downshear operation appeared to involve a significant amount of capture of airborne respirable dust. The same amount of dust was measured when using the high-efficiency and regular nozzles. The dust levels when using the high-efficiency nozzle were about 20 pct less than those measured when using the low-efficiency nozzle. The sump-upshear operation seemed to involve a predominance of other aspects of dust suppression, such as impaction of spray drops onto the face. Compared with the downshear operation, there was a significant reduction in dust levels for a total face operation when using the regular nozzle; dust levels when using the regular nozzle were about 15 pct lower than those measured when using the high-efficiency nozzle.

Jan 1, 1975

By R. J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) has recognized that Noise-Induced Hearing Loss (NIHL) is the most common occupational illness in the United States. The use of heavy equipment, the drilling of rock, and the confined work environment are some of the factors that contribute to high levels of noise exposure to workers in the mining industry. Every day 80% of the nation’s miners go to work in an environment where the time weighted average (TWA) exceeds 85 dBA. Moreover, 25% of the miners are exposed to a TWA noise level that exceeds 90 dBA, the Permissible Exposure Limit (PEL). Furthermore, a NIOSH analysis of a large sample of audiograms showed that at age 50 approximately 90% of coal miners and 49% of metal/non-metal miners have a hearing impairment. By contrast, only 10% of the non-occupational-noise exposed population has a hearing impairment at age 50 (Franks, 1997) (Stephenson, 1998). Simply stated, the majority of miners have a hearing loss by the time they retire. While NIHL is the most common occupational disease in this country, this problem is especially acute among workers in the mining industry. There are several barriers to reducing NIHL in the mining industry. These include: gaps in knowledge of noise dose/source relationships, the unavailability of effective noise controls, and needs for worker education and worker empowerment. A related issue is the difficulty of communication in noisy workplaces by both hearing impaired and normal hearing workers. The Pittsburgh Research Laboratory (PRL) at NIOSH has strategically developed a hearing loss prevention program for overcoming these respective barriers in an attempt to reduce NIHL in the mining industry. This paper provides an overview of the research program being conducted at the PRL.

GLOSSARY Acid- and toxic-forming materials. Rock or coal layers containing significant amounts of pyrite or other minerals which, if exposed by coal mining, will cause acid or toxic drainage to occur when acted upon by air and water. Add mine drainage. Any water with a pH less s than 6.0 draining from a coal mine. Water is often orange-colored because of the presence of oxidized iron. Adit. An underground mine entry at sites where coal seams are exposed at ground level. Apple core. A complete hilltop (360°) left exposed by not backfilling the highwall. Approximate original contour. The surface configuration achieved by backfilling and grading the mined area so that be reclaimed land closely resembles the general pre-mining surface configuration and blends into and complements the drainage pattern of the surrounding terrain. Area mining. A surface mining method that is carried on in level to gently rolling topography on relatively large tracts of land. Active area mine pits may be several miles long. Arid and semiarid regions. Lands, generally west t of We 100% meridian, where water use by native vegetation equals or exceeds that supplied by natural precipitation, and rainfall is insufficient to support agriculture. Annual precipitation is normally 20 inches or less. Auger mining. A mining technique often used by surface mine operators when the overburden becomes too for the coal to be mined economically using traditional surface mining methods. Large-diameter (usually 2'-4') horizontal holes are drilled as much as 300 feet into We vertical Me of the coal bed by an auger. Like a bit used for boring holes in wood, coal augers consist of a cutting head with a screw-like extension. As the auger turns, the head breaks up the coal and the screw carries it back into a conveyor that loads it directly into a truck. Backfilling. The operation of refilling an excavation using material removed during the mining process. Bench. The level or flat working area at the base of the highwall that is excavated between the exposed coal seam and the original surface of the ground. Bucket wheel excavator. A continuous-digging machine that uses a rotating vertical wheel with buckets for large-scale stripping and excavating. Cessation Order. Order to cease mining issued to a coal operator by the regulatory authority due to severity of violations, Contemporaneous reclamation. Restoration of mined land that occurs as soon as practical after coal removal. Contour mining. A mining method commonly used in eastern mountainous topography where coal is removed in a narrow strip around the hillside. The extent of the cut into the hillside is determined by the depth of overburden at the highwall compared with the thickness of the coal seam. Daylighting. A term used to describe a surface mining procedure that exposes abandoned underground coal mine workings to enable removal of the remaining coal. Daylighting is followed by land reclamation. Dragline. An excavating machine, usually used in large, flat areas, that drags a bucket (which holds up to 220 cubic yards of material) toward the machine by cables, loads it with spoil, and then hoists it wit a boom up to 350 feet long, allowing the machine to excavate wide benches by depositing the spoil hundreds of feet away from the highwall. Grading. The process of smoothing the disturbed areas of the mine site, after the coal is removed, to closely approximate the pre¬mining terrain. Haul road. Any road constructed, improved, maintained, or used by mine operators and located within the permit area. Head-of-hollow fill. See "valley rill." Highwall. The cliff-like excavated face of exposed overburden and coal in a surface mine. Hydroseeding. Planting of seed mixed in a water medium. Water, mulch, lime, fertilizer, and seed are blended and sprayed onto regarded soil.

Jan 1, 1992

Work on this program was supervised by R. C. Streeter, Project Scientist, R. K. Young, Principal Investigator, and R. A Glenn, Project Director Technicians involved in the conduct of the experimental work were J R. Allender, D. R. Wolber, G. L Maclay, and A. C Rupert The assistance of Project Scientists C. T. Ford in the electrokinetic studies, and R. R. Care in the spectrographic analyses, is also acknowl- edged. The valued advice and guidance during the course of this program from R. D Hill, EPA Project Officer, and Dr. D R. Maneval, Director of Planning and Coal Research for the Department of Environmental Resources, Commonwealth of Pennsylvania, is sincerely appreciated.

Jan 1, 1971

By Launa G. Mallett, Charles Vaught, Kathleen M. Kowalski, Charles D. Litton, Michael J. Brnich, Ronald S. Conti, Henry P. Cole, William J. Wiehagen

How do people behave when they are trying to get out of a fire? Are escape activities different in each incident, or will most actions be predictable across events? Do persons make the same sorts of decisions whether they are responding as individuals or as group members? Because the social costs of fire-related deaths and injuries are likely to continue to rise, societal pressure for greater safety will also undoubtedly increase. There are, therefore, compelling reasons to further our understanding of action in fires. If human behavior in fire is studied scientifically and predicted according to some well-defined principles, the benefits will be significant. Design engineers could incorporate real-world findings into their plans. Equipment manufacturers could gain from insights into how their technology is actually used in fire emergencies. Safety personnel would have a better appreciation of what constitutes adequate evacuation procedures. Trainers could upgrade the content of their courses that teach escape skills. The result would be an overall improvement in the quality of fire preparedness and safety.

Jan 1, 2000

Develop a simple and practical technique to measure in situ rock mass properties for realistic design and stability evaluation of underground structures. Background The Bureau of Mines has developed basic principles and techniques to determine in situ rock mass properties including Poisson's ratio, deformation modulus, and yield and failure strengths. An instrumentation package consisting of three pressure cells is installed in a single drill hole. Cell pressure response data are acquired and used to calculate and determine the rock mass properties. How It Works A test hole of BX size (approximately 5.7 cm) or larger is drilled to the approximate depth of the measuring point. The last portion of the test hole is drilled with precision bits to EX size (approximately 3.8 cm). The instrumentation package, which consists of one 3.8-cm-diameter cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated, flat borehole pressure cells (BPC's), is then installed. A complete history of cell response to changing strata loads is acquired on a continuous basis with a chart-type hydraulic pressure recorder. From these cell pressure data, Poisson's ratios, deformation moduli, and yield and failure strengths are calculated and determined.

Jan 1, 1990

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Mine ventilation can be broadly defined as the branch of mining engineering primarily concerned with the controlled flow of air through mine airways to maintain an acceptable atmospheric environment wherever men work or travel underground. Martinson (1976) has defined three elements of mine ventilation, 1) an engineering element concerned with establishing quality control (removal of dust and gases), quantity control (regula¬tion of air direction and magnitude) and climatic conditioning (temperature-humidity control), 2) a biological element in which an understanding of biological response is used in assessing the mine environment, and 3) a philosophical element requiring judgements as to the degree of risk or worker discomfort that is socially acceptable. Most texts on ventilation, such as Hartman (1961), limit themselves to a discussion of the engineering element. Although also limiting his text to engineering control, Weeks (1928) thoughtfully addresses the other elements in the preface of his book where he states: "Life is brief and happiness elusive under the best of conditions; so beside the commercial aspect must be placed the humanitarian. Is it not reasonable that the operator should give his men a chance to spend their working hours in a comfortable environment, with the danger of sudden death or disability reduced as much as possible?" The statutory requirements of ventilation are, in most countries, established on the basis of biological response as determined by basic research or are dictated by social awareness, often touched off by major disasters, resulting in demands on regulatory bodies for more stringent requirements. To a limited extent, the philosophical and biological elements of ventilation are intertwined in that social awareness may

Jan 1, 1977

By Paul T. Allsman

Iron-ore deposits in southwestern Utah, as the major source of iron ore for western steel plants, were investigated by the Bureau of Mines in 1942-45 in cooperation with property owners and operators and with the assistance of the United States Geological Survey with a view to determining and extending the known reserves. The factual data resulting from that project were presented in a previous report and in a report on the geophysical surveys now in course of publication. The present report has been prepared in response to expressed public interest in the ore reserves of Iron County. Mining began in the district in 1871} but. did not become important until 41 1923. From 1923 to 1946, inclusive) production totaled 10,139,500 long tons. In 1945 the district yielded 1,931,749 long tons containing 52.84 percent iron; in 1946 the corresponding figures were 1,317,671 and 53.75. The deposits lie .in a narrow, 23-mile long belt extending northeasterly from Washington 'County into Iron County along a line of mountains, chief of which are Iron Mountain, Granite Mountain, 'and Three Peaks in Iron. County. The deposits are hematite-magnetite bodies, chiefly in limestone near its contact with the monzonite of the mountain masses, but with a few important veinlike bodies in the monzonite or at the contact. They range in size from small pods to several millions of tons, and in depth from surface or near-surface to a known maximum of 1,300 feet:

Jan 1, 1948

By P. Delogne, L. Deryck, R. Liegeois

So far as the propagation of electromagnetic waves is concerned, an underground tunnel behaves like a pipe or hollowed waveguide. Waves propagate in this tunnel with a low attenuation only if their frequency is higher than a so-called critical frequency which depends on the shape and mostly on the cross -dimensions of the tunnel and which value is in the neighbourhood of several tenths of MHz. However, when a metallic conductor is stretched along the gallery the electromagnetic characteristics of the latter are considerably modified and the effect of the cut-off frequency disappears; this is due to the fact that the gallery equipped with such a conductor works like a coaxial cable where the conductor serves as the outward conductor and the wall of the gallery as the return conductor. This is the principle of the monofilar waveguide cable which has been perfectly studied by Gabillard. Two mean characteristics of the monofilar mode are as follows: first of all, when the cable is suspended in the middle of the cross section of the gallery, the electromagnetic field occupies all the space between the wire and the walls of the gallery. When the wire is close to the wall, the electromagnetic field tends to become concentrated between the wire and the wall, with the consequence that, with the given monofilar mode power, the aerial of a receiver standing somewhere in the tunnel will capture a weaker and weaker signal. Secondly, owing to the fact that the mode of monofilar propagation uses the ground as return conductor, its power of propagation is considerably diminished; the closer the wire is to the wall the higher the attenuation, for only a very small part of the wall is utilized as return conductor. To cover great distances, everything else being equal, two or more conductors must be placed in the gallery. If the distance between two conductors of a cable is much smaller than the distance between one or other of the conductors and the walls; or again if one of the conductors surrounds the others and forms a screening, two sorts of modes appear: on the one

Jan 1, 1973

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Center are developing ways to protect the health of miners. Part of that effort is improving the air quality in metal/nonmetal mines by developing proper ventilation techniques. The air quality of large opening nonmetal mines can be greatly improved by using engineering controls of contaminant prevention and proper ventilation techniques. Contaminant prevention includes methods to reduce contaminants from entering the mine air. Ventilation can be improved with appropriate fan selection and fan operation used in conjunction with air coursing using manmade and insitu rock stoppings.

By Mark Larson, Steve Iverson, Brian G. White

The authors hypothesize that excavation-induced extension fractures are caused by elastic shearing displacement that in turn causes tension oblique to a propagating shear zone. Such extension is manifested as tension on scales larger than that of microcracks. En echelon fracture patterns are a common result. FLAC modeling confirmed that localized tension is created near the corners of mine openings. In the model, tension was concentrated at the leading edge of a simulated fracture in a pattern that could promote the formation of an en echelon fracture. Particle Flow Code models confirm progressive formation of en echelon tensile failures with distance from an opening. The elastic displacements and the resulting fractures facilitate reduction in applied load at the expense of shear deformation and lateral dilation. Understanding the mechanics of fracture and deformation is vital for designing more effective ground support practices, a major objective of ground control research being conducted at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health.

By C. M. K. Boldt, R. L. Levens, A. D. Marcy

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface are aexposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 1995

By R. S. Conti, C. D. Litton

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide(CO) sensors, and a point type heat sensor (PTHS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s. The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS. A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and CO sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity. Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners’ escape.

Jan 1, 1995

By D. K. Ingram, G. L. Mowrey, T. R. Rehak

This paper summarizes fly rock and blast area security fatalities from 1989 to 1999 and examines the causative factors. Coal and nonmetal mining used about 43 billion pounds of explosives and blasting agents between1989 to 1999. A majority of this consumption was used at surface mines. Accident data indicates that fly rock and lack of blast area security were the primary causes of blasting related injuries in surface mining. Fatal injuries due to lack of blast area security were attributed to: failure to clear blast area; failure to follow instructions; inadequate guarding; inadequate blasting shelter; and unsafe location. Seven fatalities due to fly rock and lack of blast area security were reported in surface coal mines and six in nonmetal mines. Out of these, two fatalities (one each in coal and nonmetal mines) occurred outside the mine property. In the coal mining sector, two fatalities were attributed to fly rock, and five to lack of blast area security. In the nonmetal mining sector, three fatalities were attributed to fly rock, and three to lack of blast area security. Preventive measures include: ensuring that all personnel have evacuated the blast area during shot firing; using adequate blasting shelters for employees whose presence is required in the blast area; controlling and monitoring all entrances to the blast area; ensuring that the blast is properly designed, drilled, and loaded; and emphasizing education and training to enhance skill levels for implementation of engineering control techniques.

By Earl C. Lane

This is the second of a series of reports on a survey of petroleum products manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in other parts of the United States, and the claim has been made that some of the present federal Specifications for petroleum products tend to discriminate against California products. The purposes of the present survey are to determine what particular specification requirements California petroleum products characteristically fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what 'lines investigation to determine the question should proceed. The first report* of the series gave the physical and chemical properties of gasoline and mineral spirits made from California crudes. The present report deals with lubricating oils. Sixty-one samples of lubricating stocks and finished commercial products were generously donated by four of the large refining companies of California. Fifteen samples of automobile lubricating oils, made in California from California crudes, were purchased in the open market. Nine samples of lubricating oils mode from Gulf Coast crude were contributed for comparison by a company in Texas. The refining companies have continued the helpful and cordial cooperation shown by them in connection with the earlier work of the survey.

Jan 1, 1923

Develop a method to evaluate the effectiveness of coal scam fire surface seals so that potential problems may be corrected at an early stage, before the integrity of the surface seal is lost. Background Surface seals are the primary coal seam fire abatement method being used in the western United States. Surface seals smother a fire by denying it oxygen. The seal is usually constructed by placing a mantle of soil, four to ton feet thick, over a coal scam fire area to exclude air from the fire. The soil is compacted to increase effectiveness, and a soil cement may be used to augment the soil. In some cases, burning coal may be excavated and separately smothered or otherwise extinguished in another area; in other cases, a trench maybe excavated and backfilled with incombustible material to isolate a fire. More often, a surface seal is simply applied over and around the entire known burning area. In the 1950's, the Bureau of Mines administered a large program to treat numerous coal seam Fires across the western United States. Methods used in this program were described in Bureau of Mines Information Circular (IC) 7932, dated 1959. More recently however, various coal seam fires have been treated with surface seals under the direction of state Abandoned Mine Land Reclamation authorities. It has frequently taken years to evaluate the effectiveness of surface seals. By the time problems become evident, it has often been too late to take corrective action within the scope of the original abatement project. For this reason, the Bureau of Mines developed a means for tracking temperature trends at coal seam fire projects to obtain a better and earlier handle on the effectiveness of surface seals.

Jan 1, 1991