Search Documents

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971

By Howard E. Parkinson

The mine pager phone to public telephone interconnect system permits mine paging telephones to be interconnected with the public phone system, thereby providing emergency and off-hours communications. The system, a push-to-talk, push-to-listen system, is compatible with any mine paging system utilizing dc voltage on the line to enable paging. A tone generator of the proper frequency enables an outside caller to page over mine pager system loudspeakers. A caller inside the mine can make an outgoing call to a preselected, preprogramed number with the use of a proper frequency tone generator. The system includes an automatic hangup timer that restricts the time off-line due to a wrong number or incorrect hangup to 20 seconds and 6 minutes, respectively.

Jan 1, 1974

By J. J. Jakosky, D. H. Zellers

"IntroductionThe Bureau of Mines has been conducting experiments in underground communication during a period of several years, and a brief summary of what has been done is as follows:During 1919-1920, investigations were conducted with the geophone. This instrument was used extensively during the World War for detecting enemy digging and mining operations, by means of the vibrations transmitted through the earth strata.A preliminary investigation using short wave-length (200 to 300 meters) radio equipment carried out jointly with engineers of the Westinghouse Electric & Mfg, Co. during 1922.The step was to investigate ground conduction signaling, (called T.P.S. in Signal Corps parlance)."

Nov 1, 1924

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber—sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases some of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of cable left on the reel.7. The type of cable used.8. The kind of reel used.In connection with an investigation of the general performance of rubber—sheathed trailing cables, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By H. H. Schrenk

There are several well-recognized procedures for controlling exposure to hazardous atmospheres in industry. They include (a) substitution of less toxic material, (b) enclosure of processes, (c) wet methods, (d) local exhaust, (e) general ventilation, and (f) use of respiratory protective devices. In addition to their employment as a control measure in occupational exposures, respiratory protective devices also are essential in emergencies that may arise from failure or improper use of other control equipment. Respiratory protective devices usually are employed to supplement other methods of control, as temporary expedients, or when other methods are not readily applicable or practicable. It seems reasonable to assume, however, that where respirators are used consideration has been given to the factors involved and that the devices can provide satisfactory protection if used properly. Their use should not be arrived at simply by a process of elimination of other methods that are more difficult to apply.

Jan 1, 1943

By Edward A. Mihok

Laboratory batch-flow tests conducted on a highly ferruginous acid mine water with an activated carbon showed that ferrous iron is rapidly oxidized. This indicates that air oxidation of ferruginous acid in mine waters is catalyzed by activated carbon. The ferrous iron content of an acid mine water flowing through an aspirated activated carbon column was reduced from about 700 to about 10 parts per million in less than 1 minute. Highly efficient ferrous iron oxidation was achieved by conditioning the activated carbon by repeated treatment with acid mine water and air. The reaction proceeds rapidly in the acid environment (pH about 2.5) engendered by ferrous iron oxidation. The activated carbon was used repeatedly with little loss in efficiency, no discoloration, or solids deposition. In these batch tests, about one-third of the iron was adsorbed by the carbon, but with continuous flow, little iron adsorption is expected. Incorporating a catalytic oxidation step in the treatment of acid mine waters containing ferrous iron would greatly facilitate neutralization--precise control of pH, lower reagent costs, elimination of aeration equipment, and smaller holding ponds.

Jan 1, 1969

By John C. Edwards, Fred N. Kissell

Experimental work by the Bureau of Mines indicates that when a coalbed is degassed by boreholes, the flow of methane may actually increase with time. This phenomenon appears to be the result of a relative-permeability effect; that is, the coalbed permeability to the gas increases sharply with decreasing water saturation. This report reviews the background of experimental evidence indicating a relative-permeability effect, and presents the results of a computer simulation of two-phase flow in coal.

Jan 1, 1975

By R. V. Ramani, P. M. T. White, D. Sutton

6.1 Summary This report deals with the investigation carried out to select, test, and implement a method of evaluating coal deposits and reserves. Cognizance is taken of the inherent characteristics of coal and the legislation covering aspects of health, safety, environment, and ecology applicable to the coal mining industry. Further, the method is computerized and provides information that is meaningful and readily available to other programs and sub¬systems within the concept of the Master Design Simulator. The Geology and Reserves Sub-system interface with the total system is provided by a geological data library which is structured to hold and make accessible all the data required by the system. The output from the program is accurate and useful to users with a wide variety of computer experience, knowledge, hardware and storage capacity. The sub-system is designed to function as a separate unit or an integral part of the total system and, there¬fore, an interface to or with the system has been established. The work carried out by the sub-system includes: (a) The analysis of raw geological data. This involves:

Jan 1, 1974

By R. V. Ramani

"In a 1985 seminar, we were told that over-optimism abounds in Artificial Intelligence (AI), that AI is neither a science nor a technology yet, and that we will be both exhilarated and disappointed with AI. In fact, even today, there is no single accepted definition of AI; however, certain features have been identified by AI researchers as essential to consider an entity (e.g. machine or program) to be intelligent. According .to Shank (1987), these features include communication (to be able to communicate with), internal knowledge (knowledge about itself), world knowledge (awareness and knowledge about the world outside), intentionality (knowing what one wants and a plan to seek it, ie. goal seeking behavior), and creativity (being adaptable to changing conditions). None of these figures would individually define intelligence; however, each would be a part of intelligence in its own way.The prospects for the development of entities with AI have never been as good as they are now. The combination of advancements in computer hardware and .software along with new insights into the ways in· which we store knowledge and use it for problem solving has enhanced the potential for the creation ~f intelligent entities. After some unbounded optimism of a major breakthrough in the fifties and frustrating disappointments in the two following decades, it appears now that AI has emerged from research labs to industrial practice. This is confirmed by the growing number of repeat applications of AI in business and industry to the extent that AI can now be considered a technology.AI applications are categorized into several distinct areas such as Natural Language Processing, Speech Recognition and Synthesis, Expert Systems, Robotics, Machine Vision, etc. Of these practical realizations, Expert Systems (ES) has the greatest potential for meeting the decision-making needs of the manager in the ever-growing complex scoio-technical systems. Prof. Feigenbaum, an expert and leader on expert systems, has defined Expert System as"" ... an intelligent computer program that uses knowledge and inference procedures to solve problems that are difficult enough to require significant human expertise for their solution. Knowledge necessary to perform at such a level, plus the inference procedures used, can be thought of as a model of the expertise of the best practitioners of the field."""

Jan 1, 1989

Enhance hydraulic fragmentation technology by developing alternative grout sealing methods. Traditional grout scaling methods rely on chemical adhesion and require large contact areas to restrict high-pressure fluids. Fluid injection into rock requires economical and effective seals. With economical and effective seals, rock is easily fractured in tension by high-pressure fluid injection (fig. 1). Approach An innovative grouting technique was developed and tested by the Bureau. Slowly hydrating expanding chemicals are placed within a borehole and around a section of high-pressure tubing. Testing was conducted using 9/16-inch-OD smooth-walled injection tubes in 1.5-inch-ID holes. Seal lengths weir less than 10 inches and curing times were less than 24 hours.

Jan 1, 1989

By J. E. Murphy

The Bureau of Mines developed a hydrometallurgical method for recovering mercury metal from mercury sulfide concentrates. Sulfide flotation concentrate from the McDermitt Mine was leached in a cupric chloride solution at 80° C. The redox potential of the solution was maintained at 850 mV during leaching by chlorine sparging. Mercury extractions exceeded 99 pct in 3 h of leaching. After leaching, the pH of the solu-tion was increased from 1 to 4.5 to precipitate copper as atacamite. The pregnant solution typically containing 100 giL Hg was sent to elec-trolysis to produce high-purity mercury metal and chlorine for recycle. In a 200-A electrolytic cell operated for 24 h, current efficiency was 99 pct and the energy requirement was 0.9 kW·h/lb of mercury produced. Mercury removal from the waste stream was also investigated. Iron or zinc cementation, sulfide precipitation with H2S, and activated carbon adsorption all decreased the mercury concentration from 10 giL to 0.01 mglL, which is less than the Environmental Protection Agency limit on wastewater of 0.02 mg/L.

Jan 1, 1987

By R. H. Fernald

In investigating general problems that relate to the fuel resources of this country, and in testing fuels belonging to or for the use of the Government, the Bureau of Mines has given considerable attention to the efficiency and economic value of producer-gas power plants. Government inquiries during the past eight years not only have shown a very low fuel consumption per horsepower-hour for these plants but have demonstrated conclusively the possibility of utilizing commer- cially low grades of bituminous coal, lignite, and peat in plants prop- erly designed for the use of these fuels. The anthracite plant has been recognized as a commercial possibility for several years, although the cost of the fuel used has in general restricted these plants to com- paratively small units. The commercial development of the producer-gas power plant in the United States has been largely within the past six or eight years. In 1909 the United States Geological Survey published in a bulletin entitled "Recent Development of the Producer-Gas Power Plant in the United States" a list of producer-gas power-plant installations. The data presented in that bulletin showed a strong development in this field and led to much conjecture as to the future of this type of power. Owing to the extensive introduction of the steam turbine, however, many persons predicted the almost immediate doom of the producer-gas plant. In addition to the inroads made by this formida- ble rival, the interest of the gas-engine enthusiasts became centered to such an extent in the oil engine that the gas producer was relegated to second place by many and absolutely abandoned by some. During the past three years the belief of many who were formerly firm be- lievers in the gas producer has been that this type of power has reached its height of development in this country and that from a commercial standpoint it can no longer be regarded as a complete success. This feeling of commercial decadence has become so general

Jan 1, 1913

By Lucien Eaton

This paper describing the mining practices at Mine No. 2 of the Marquette Range, Michigan is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various minim; districts of the United States. The publication, of this information should be of interest to the industry at large and the exchange of ideas thereby made possible should be of economic value to operators in all harts of the country. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of the property discussed in this paper for much of the information presented. The geological classification is taken from publications of the U. S. Geological purvey.

Jan 1, 1929

By E. D. Gardener, Byron O. Pichard

"Methane, frequently called fire damp or marsh gas, is very well known to coal miners but to thy average gold miner it means nothing, as it is not associated generally with the rock formations in which gold is found.We have recently been conducting a study of mine air in typical gold mines on the Pacific Coast, and out of five California mines in which the air was sampled, three showed methane. Each of these three mines, referred to below as mines A, B, and C, have had accumulations great enough to be ignited. An authentic report from another California, gold mine, which has not yet been sampled, states that recently the superintendent was seriously burned by the ignition of a pocket of gas. This mine is later mentioned as mine D.Mine A is an old mine which had been abandoned for several years and permitted to fill with water. It has been unwaterad recently, and is now being developed at greater depths. During the unwatering, gas bubbles formed on the water and upon being ignited burned freely. It is reported that two men were seriously burned from accidentally igniting the gas. Samples of the bubbles on analysis showed high percentages of methane. Since the mine has been unwatered, no trouble has been experienced through gas being ignited. However, out of a total of six air samples which we took recently in scattered working places, all showed small amounts of methane, the methane content being 0.06, 0.04, 0.05, 0.04, 0.04 and 0.07 per cent, respectively. When these samples were taken methane was not suspected, but its general presence in the mine air indicates that it is being given off constantly."

Dec 1, 1921

This report describes magnetic field measurements in the Helvetia Coal Co. Lucene #8 Mine for purposes of deriving a mapping of the magnetic field strength covering the major haulageways which contain conductors. The measurements were performed by Terry S. Cory, P.E. under U.S. Bureau of Mines purchase order P0372716. Assisting in performance of the measurements were personnel from the Bureau of Mines, PMSRC, and Helvetia Coal Co. Acknowledgement is given to Engineer Tom Strong of Helvetia Coal Co. who accompanied the measurement team and who lended support in performing the measurements and in supplying valuable engineering information for use in evaluation of the results. The results of the testing at medium frequency show that coverage of the entire mine area containing conductors can be achieved employing wireless radio techniques whereby radio signals are coupled into and are carried by these conductors. These results confirm earlier qualitative testing of the Collins Mine Wireless Radios in this mine. These results, performed over the frequency range 71-2890 KHz, illustrate the effect of frequency on the radio propagation with the conclusion that the best overall coverage is obtained at frequencies approximating 1000 KHz. This report presents all the raw data and the reduced data in the form of magnetic field strength contour maps. Sufficient information is provided to enable independent reduction of the data. A summary of observations which can be made directly from the contour maps is given.

Jan 9, 1977

By A. K. Schellinger

1. In the United States, the industrial application of centrifugal force for separating phase constituents has been confined almost entirely to aqueous systems at room temperature. This paper presents results for experimental tests on the use of centrifugal force for separating the liquid and solid phases in molten nonferrous alloys. 2. The development and use of a small centrifuge for treating molten metals is described. The centrifugal apparatus was, in essence, a 3-inch diameter spinner pot, which revolved, within -a gas -fired furnace, at speeds up to 3,000 r.p.m.

Jan 1, 1953

Remotely monitor overburden response to longwall mining using time domain reflectometry (TDR) and a combination of hardware and software, as part of the U.S. Bureau of Mines (USBM) program to characterize subsidence. Background TDR was developed in the 1960's as a method to locate, discontinuities in coaxial transmission cables. In this method, voltage pulses sent along a cable are reflected by cable defects. The pulse reflections are used to determine the type and magnitude of the defects. The TDR concept was extended to material property measurement by embedding cables into particular materials and evaluating the cable's dielectric behavior as material properties were modified. This technique was adapted by the USBM in 1978 for use in monitoring rock movement during underground mining. The same concept is utilized today. A coaxial cable is grouted into a rock mass that is expected to deform. Progressive rock movement causes the cable to deform, as shown in figure 1, and changes to occur in the cable's electrical properties, which then produce changes in TDR reflection signatures. The technology has advanced to the point where it is now possible to distinguish shear deformation from tensile deformation and to quantify rock mass displacements by analyzing the TDR signatures.

Jan 1, 1995

By J. V. Scalera

Because of U.S. dependency on imported critical metals, the Bureau of Mines has conducted research to evaluate the possible substitution of nitrided low-alloy steels for higher chromium-containing alloys. The corrosion data for nitrided steels are limited primarily to the Soviet literature. The objective of this study was to determine the corrosion properties of six commercially nitrided low-alloy steels in a 5-wt % NaCl solution at pH 4. Weight-loss tests indicated that, in deaerated test solutions, most of the nitrided steels were less corrosion resist-ant than nontreated steels. However, electrochemical tests indicated that under more oxidizing conditions, nitrided materials are converted to a passive state with a significantly reduced corrosion rate. Elec-trochemical tests performed in an aerated environment confirmed the passivity of the samples in an oxidizing environment.

Jan 1, 1984

By G. W. Jones

Phthalic anhydride is a solid having the formula C8H4O3. It is an important intermediary in production of anthraquinene, alkyd reins, and plasticizers. The combined annual production of phthalic anhydride reported by 10 major manufacturers for 112,250 tons. The raw materials in the manufacture of phthalic anhydride have been the source of numerous fires and explosions. Consequently, the need was felt to determine the temperature flammability and the ignition temperatures crude basic raw material in most phthalic anhydride production crude phthalic anhydride, and pure phthalic anhydride.

Jan 1, 1950

By D. W. Frommer, M. M. Fine

Laboratory investigations have produced flotation concentrates contain- ing 91 to more than 92 percent titania, with fair recoveries, from the Christy property, Hot Spring County, Ark. The titanium-bearing ore on the Christy property occurs in a quartz-clay- iron oxide mineralization, which contains, on the average, about 6.0 percent TiO2, chiefly as the mineral brockite; brookite and rutile are different crys- talline forms of titanium dioxide. Recent work by the Bureau of Mines has shown that titanium chloride can be produced readily from the rutile-type mineral by reduction with coke fol- lowed by low-temperature chlorination. Metallic titanium is in turn derived etallic from the chloride by the Kroll process .

Mar 1, 1952