Search Documents

By Robert Hopler

INTRODUCTION NOT so very many years ago the farm was about the last place where one would expect to find up-to-date mechanical appliances. Steam, explosives, electricity—the factors which have made the world in general, and America in particular, what it is today— were indispensable for the railroad and the steamboat, the factory and the mine, but the farmer’s work was generally run on a comparatively small scale, and was mostly done by the muscles of men or draft animals. Today, however, the farmer as well as the manufacturer, the contractor and the miner, fully appreciate the value of labor-saving devices. Every up-to date farm, large or small, has modem machinery that tends to reduce the cost of production or to improve farm products.

Jan 1, 2011

By Alejandro Rosario, Ricardo González

The restrictions imposed by the Brazilian environmental legislation regarding natural caves lead to a block of substantial amount of mineral reserves. Mining activities can released caves, as long as the company ensures that the activities will not cause any damage to them, requiring profound and time-consuming studies. Since the use of explosives in the mine are potential sources of some damage to any structures, it leads to a deep need for controlling the rock blasting activities. In this context, the maximum charge per delay used in operations close to cave regions must follow some internal blasting assumptions that have been developed during specific tests and mining activities. By the seed wave technique, it is possible to determine the behavior of a seismic wave, which travels through a rock mass and it is generated by blasting a known explosive charge. This technique has proved to be an effective tool because it is able to accurately include the physical characteristics of the rock and different lithologies. This paper discusses about modelling blasting induced vibrations in order to improve caves protection, which surround the mining operations.

Jan 1, 2019

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By Jennifer Paukula, Steven Lindsay, S. Joon Kim

String loading is the placement of a bead or ‘string’ of emulsion along the lower edge of a development drill hole. The loading hose extraction rate controls the amount of emulsion placed in each drill hole. This allows a controlled distribution of explosive energy throughout the development round. Center holes are loaded using the slowest extraction rate causing the majority of the explosive energy to be placed in the center of the round. The loading hose is extracted successively faster for the buffer and perimeter holes causing less explosive energy to be placed near the edge of the blast. This causes less damage to the rock mass that remains in place after the development blast.

Jan 1, 2012

By Bob de Raadt

For a long time industrial underwater blasting has stood in need of a calculation method, for the determination of shockwave-proof as well as shockwave-effective charge distances to objects in water. After a brief discussion of the physical background of the shockwave mechanism in water, the author discusses an empirical theoretical computing method based on the "Bubble boundary" concept. The practical application of this model is finally shown in an account of a few underwater blasting operations in which charge weights of c.1-1000 kg were involved.

Jan 1, 1980

By Gungor Tuncer, Ali Kahriman

This paper presents the results of ground vibration measurements carried out in Hisarcik Boron open pit mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 304 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 2 different types vibration monitors (1 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2006

By D Larson, M Finger

Chemical explosives may become a key element in many of the in situ energy and mineral recovery methods under development. This paper discusses the potential role of explosives in deep rock mining for resource recovery. Several energy and mineral recovery programs described are an outgrowth of the Plowshare Program and Explosives R&D conducted as part of the AEC/ERDA mission at Lawrence Livermore Laboratory. Several important aspects of the use of explosives in deep rock mining are reviewed. First, the status of knowledge of deep rock fracturing to create permeability underground is discussed. Completely contained blasting has not been a widely applied tool used in the mining industry. We conclude that data available on deep rock fracture is minimal and that the mechanisms that control the processes must be understood before technical and economic feasibility can be established. We also discuss the unusual problems in the selection of an explosive or blasting agent for deep rock applications including emphasis on the functioning at depth and safety aspects. Finally, a brief review of similar activities within the U.S. is given.

Jan 1, 1976

By Richard J. Mainiero, Eric S. Weiss

This project investigates the behavior of blast waves from the detonation of high explosives in an underground mine. A series of explosive tests was conducted in the underground and surface facilities at the Bureau of Mines' Lake Lynn Laboratory to evaluate the potentially dangerous effects of blast waves produced by open shooting, blown out holes, or accidental detonations of explosives. Shots of C4 and TNT were fired at the dead end of a 6 ft high by 20ft wide entry, at the intersection of two entries, and on the surface. C4 and TNT were chosen for this research because they exhibit very consistent performance. Behavior of the blast wave was evaluated through recording of the pressure as a function of distance from the explosive detonation.

Jan 1, 1995

By Italo Onederra, Jason Furtney, Ewan Sellers

The Hybrid Stress Blasting Model (HSBM) is a high level blast modelling research tool which provides results that can still be used implicitly for practical blast design. The code is being developed through an international collaborative research project funded by a consortium of companies which is comprised of explosive, equipment suppliers and major mining houses. A key component of the HSBM is the numerical code and user interface designated as Blo-Up 2.5. To date validation work has focussed on breakage, fragmentation and damage outcomes in controlled laboratory experiments and using large concrete cubes

Jan 1, 2012

By Brian Stump, D. Craig Pearson

This work quantifies seismic coupling as a function of charge weight for single-fired (simultaneously detonated) explosions observed in the mine and at regional distances. These single-fired explosions are contrasted to standard production shots from the same mine. Production shots include cast blasts to remove overburden and coal shots for fragmentation. The blasts were conducted in a mine in NE Wyoming. The data sets consist of measurements in the mine (100-10,000 m) and at regional distance (360 km) using a seismic array near Pinedale, Wyoming (PDAR). The single-fired explosions ranged in designed size from 5,500 to 50,000 lbs. Peak amplitudes measured at a single element of the regional array are modeled by a power law relation dependent on explosive weight. Scaling constants were determined for each of the dominant regional phases: b(Pn) = 0.84±0.14; b(Pg) = 0.84±0.09; b(Lg) = 0.91±.08. Spectral ratios of observations from different explosions observed at the same station illustrate the frequency dependnce of the source scaling relations. Spectral ratios of in-mine observations are consistent with those of regional data. The observed single-fired ratios are well replicated by Mueller-Murphy source model ratios. The data and model illustrate both the increase in long-period spectral level and the accompanying decrease in source corner frequency with increasing charge weight. The coal and cast blasts that make up the production shots ranged in size from 77,000 to 4,738,230 lbs. The peak amplitude (1-20 Hz) for the largest delay-fired production shot (4,738,230 lbs.) is comparable to that of the largest single-fired explosion (50,000 lbs.). This comparison can be explained in terms of destructive interference between waveforms from individual boreholes introduced by delay firing. Shot specific models of delay firing suggest that peak amplitudes in this same frequency band for the production shots are insensitive to the total amount of explosives in the blast. Peak amplitude data at regional distances supports his modeling result.

Jan 1, 2002

By Thomas E. Ricketts

An important part of underground mine planning and operations involves the reclamation of working areas after blasting before the mining cycle can continue. This is especially true for mining that must use large blasting operations in the vicinity of extensive underground workings. In an effort to develop a rational procedure for estimating mine damage produced by blasting, underground rock fall has been assessed for a large-scale blasting operation in oil shale. The amount of mine damage has been quantified in terms of manshifts of effort required to reclaim underground working areas after blasting. This has been further broken down into the three main phases of reclamation, i.e., scaling and excavation, rockbolting, and miscellaneous repairs on ventilation, utilities, etc. Different types of openings have also been assessed including level tunnels, incline drifts and rooms. The effect of repeated blasting on mine damage has also been documented with initial blasts producing more damage than subsequent blasts.

Jan 1, 1988

By Chuck Kliche, Bill Clements

This project involved the removal of the top of an old water supply reservoir tank for the City of Lead, SD by explosives. The general contract called for the removal of the concrete top without damaging the sides or floor of the reservoir. The option of a rock hammer was eliminated, due to the possibility of an unpredictable collapse damaging the sides or floor of the reservoir. Different blasting options were discussed between the primary contractor and the blasting contractor, along with the pros and cons of each. The primary contractor settled on the option of drilling the structure for blasting versus using shaped charges

Jan 1, 2007

By Earl C. Hutchison, Wade C. Hutchison

To effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre and post blast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By Matthew Baumann, Bahram Sameti, Tafazoli Zeng Hairong, Edmond Chow

An automated, centralized, image-based rock fragmentation analysis system provides blast engineers with the benefit of minimizing tedious and mundane work, and allows them to focus on their expertise of blast optimization. In typical manually-operated image-based rock fragmentation analysis, much time is spent on collecting proper images, handling and transferring data, and processing for fragmentation.

Jan 1, 2013

By Riaan Van Wyk, Gys Landman

In today’s mining environment the use of radio communications in the form of two-way radios, cellular phones and even automated mining, form a vital part of the daily operations of a mining site. The radio transmissions that are used are a form of energy and as with all other types of energy it can have an influence on blasting equipment.

Jan 1, 2011

By Selwyn Pearton

Pumpable emulsion explosives have been available to surface and underground massive mining operations for decades and through their unique properties offer significant advantages through improved safety, reliability and performance. Despite their advantageous properties, the benefits of pumpable emulsions have been unavailable to narrow reef mining operations due to the void in technology necessary for their successful implementation within the challenging environment. Despite efforts to promote and enhance the safety and performance of bulk emulsions for narrow reef stoping, little research has been undertaken to advance the pump technologies required for their implementation. This has resulted in a gap in knowledge and technology and as a consequence the successful implementation of a pumpable emulsion system has consistently eluded the narrow reef environment.

Jan 1, 2015

By L C. Taylor

Very small scale testing has been shown to be able to predict quite accurately, in many situations, the results of full scale testing. Small scale tests are more cost efficient, easily observed, and easily instrumented than full scale tests. Over the past 10 years small scale testing in the Dynamic Effects Laboratory at the University of Maryland has been used to successfully study the response of structures and soils to explosive detonation. Small scale testing has been successfully used to predict full scale results in underwater cratering and channeling, the loading (both pressures and impulse) on vehicles due to the detonation of buried charges, the positive effects of bottom shaping for military vehicles to reduce this loading, and the movement of obstacles underwater by explosive charges.

Jan 1, 2012

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015

By John C. Didlinger, John L. Didlinger

As we begin the pre-blast survey we need to decide on the number of holes needed for production and a detailed highwall inspection. The survey consists of checking the highwall and placement of barrier cones. At the Elmhurst Chicago Stone Company, Barbers Corner Plant, we use 18-24" orange highway type safety cones. These cones are easily noticed because of their high visibility color in all weather conditions and are placed approximately 20-25 feet from the face and approximately 50 feet apart along the highwall, then the area is checked for back break, under cut, over hang, surface filled area and clay area. This deposit is unique because of the number of clay filled areas and slip seams that meanders through the deposit plus a fault that runs North-Northwest and South-Southeast. This particular limestone deposit is overlaid with glacial sand and gravel and the top weathered stone wanders plus or minus 10 feet in 1400 feet.

Jan 1, 1996

By Lee Wehner, Daryl Kin, John Bolger

The Maumee Quarry, located in the city of Maumee, Ohio, has large in-situ cavities, ranging in size from 3 ft (.91 m) in diameter to over 15 ft (4.5 m). The drill/blast team challenge is to drill, load and shoot the geologically disturbed rock in a safe, cost efficient manner, while in close proximity to a commercial area. A continuous improvement process, managed by a Blast Optimization Team (BOT), was implemented to quantify the innovative explosive loading techniques that have been implemented. Borehole camera monitoring, modified loading practices, the need for accurate drill hole logging and open communications between the drill and blast crew proves critical to the success of the operation. Safe Standard Operating Procedures (SSOPs) have been developed and are strictly enforced for the drill/blast cycle. All blasts are monitored with seismographs and recorded on video to provide detailed information as part of the Blast Management Plan. Despite the geological challenges, the measurement of rock fragmentation index versus loader dig rates has provided near optimal crusher throughput.

Jan 1, 2007