Search Documents

By Shuji Owada, Mayumi Ito, Idemitsu Kosan Co. Ltd., Takehiko Nishimu, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

"fElectrical disintegration (ED) by high voltage electrical pulse is a relatively new technique which was demonstrated by Tomsk and Mekhanobr in the 1960’s and has been investigated in detail by Andres in the 1990’s. In the ED, the electrodes should contact to the targeted material and the energy of high voltage pulse is charged directly to the material. It has been reported that the ED is quite efficient to improve liberation of composite materials, because electrical current passes often through the conductive part and/or along the phase boundaries. Theoretically, the energy required in the ED should be lower than in the other mechanical breakage methods, because breakage occurs basically by tensile strength in the ED while in the other mechanical methods it does mainly by compressive strength which is generally ten times or higher than tensile strength.Coal, involving many kinds of mineral matters, is considered to be one of the targets for the ED to apply to. In Japan, national “Hyper-Coal Project” is now running, in which ultra-clean coal (less than 200ppm of ash, 0.5ppm of Na and K, and 2ppm of Ca) is planned to produce by combining advanced coal preparation and liquefaction technologies for the purpose of direct injection of coal combustion gas to turbine. The ED is one of the major techniques to be developed in this project, since mineral matters must be liberated before introducing to the following advanced separation processes. Liberation is important also for the utilization of middling coals generated from usual coal preparation plants. The application of the ED to the middling coals is considered effective for upgrading these coals with higher liberation degree and less energy input."

Jan 1, 2003

By G. K. Nimal Subasinghe

The establishment of grind size that optimally liberates the valuable mineral for efficient down-stream processing is of great importance for most mineral processing operations. Reasonably accurate comminution models as well as models of downstream separation processes may be found in the literature but their use in optimizing grind size is limited without an associated liberation model. In this work, an attempt has been made to address the above shortcoming by demonstrating how the effective parameters of the downstream flotation process may be predicted from the liberation characteristics based on the ore texture data for a disseminated nickel ore. In this regard, the liberation model based on linear intercept distributions of mineral and gangue proposed by King (1979) and its application to predict the flotation performance of an industrial plant demonstrated by Schaap (1979) may be considered useful contributions. However, while the model proposed by Schaap is simplistic enough, it is based on several assumptions due to the non-availability of intercept length measurements on the parent rock, in particular, on the extent of mineral exposure on the surface of comminuted particles. In this work, the linear mineral and gangue intercepts on polished specimens of a binary ore, comprising darker pentlandite as the valuable mineral and lighter barren host rock were measured using an image analyser. The resulting intercept distributions followed negative exponential distributions. Using the mean sizes of mineral and gangue intercepts, the proportion of liberated, compo-site and mineral occluded particles of a given size, the extent of mineral exposure on the surface of particles and their mean mineral contents were calculated using principles of renewal theory. The rock was then crushed and ground and different size fractions were floated. It has been shown that the parameters of observed recovery data based on 1st order kinetics such as the associated rate constant and ultimate recovery agrees well with those predicted from the quantities calculated above. This work has important practical implications since it can indicate variations in flotation performance arising from changes in mineralization within a large ore body.

Jan 1, 2014

By Khoi Nguyen, Luke Keeney

"Hardness" is an important yet diverse material physical property and is a key parameter in the mining industry in fields such as comminution, geotechnical and blast modelling. Several laboratory and field based measurement techniques exist to measure hardness (e.g. Point Load Testing, Vickers, Brinell, A*b, BMWi, UCS), all are designed for specific applications. Current tests are generally destructive and require specific sample preparation procedures which results in high cost tests that are not conducted in adequate quantities to map hardness across an ore body. The EQUOtip rebound hardness tester is a device that has been developed for application in ore body hardness domaining within the AMIRA P843 GeMIII Research Project. The rebound hardness test is non-destructive and suitable for application on half and whole diamond drill core. Data acquisition protocols and a data processing software application (EQProcess) have been developed to facilitate routine collection of comparative hardness information. This paper outlines the data acquisition and processing methodology and provides application examples of defining relative hardness domains in different geological deposit styles.

Jan 1, 2014

By S. Banisi, E. Arghavani, M. Pourkani, M. J. Rajabi, Gh. A. Mohamadian, H. Bidshahri, Gh. A. Parsapour

The Sarcheshmeh copper complex flotation circuit of plant No.1 consists of two identical north and south sections where each includes four rougher (each bank consists of 14 cells), two cleaners (each bank consists of 8 cells), two recleaners (each bank consists of 2 cells), and two scavenger banks (each bank consists of 10 cells). The reduction of feed grade along with a change in the mineralogical composition is the main reason of current lower concentrate grade (24%) compared with the design concentrate grade (32%). Because of a lower feed grade, the amount of rougher concentrate has decreased which in turn has significantly reduced the feed rate to the cleaner, recleaner, and scavenger banks. This has increased the mean residence time of the material in the cleaner section resulting in a lower final concentrate grade. A laboratory study showed that the final concentrate grade can be increased by 2-4% if one cleaner stage is added to the flotation circuit. In this research, based on the laboratory results, one cleaning stage was added to the current flotation circuit. In order to make this modification instrumentally possible in the plant, the final concentrate was gravity transported to the Mo-Cu thickeners. This released 2 pumps and associated tanks which made addition of one cleaning stage practicable. Finally, a part of the cleaner and scavenger cells were used as the third cleaning stage. This decreased the residence time in the cleaner and scavenger banks. After implementation of one cleaning stage in the south section of the plant, the performance of the circuit compared with the identical north section. It was found that at the same recovery, the concentrate grade of the south section increased by 2.5%. The promising results led to the implementation of adding one cleaning stage in all sections of the flotation circuit.

Jan 1, 2018

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By X. H. Zhou

Column flotation is being widely adopted for fine particle treatment by the mineral processing industry due to its simplicity of structure, high efficiency and good separation performance. Cyclonic static micro-bubble column flotation (FCSMC) is an innovative column separation technology that has been successfully applied in the coal preparation industry in China. Recently, the application of this equipment has been further expanded to the separation of several minerals such as fluorite, copper, iron, etc. The bottom of the FCSMC is a cone in which cyclonic field is generated when circulating pump is injected tangentially into the column. The unique cyclonic structure is believed to help enhance the column separation performance. Since the FCSMC is a new flotation device, little work has been done to understand the fundamentals of this technology. In this research, a computational fluid dynamics software, ANSYS/ FLOTRAN, was employed to simulate the flow field of a lab FCSMC system (F0.2 m, F3.0 m by length.) The distribution patterns for velocity field and flow field were investigated under single phase condition. It has been found that axial velocity of the slurry decreases and becomes stable along the height of the column from bottom to top, and the slurry performs as a descending flow pattern. Another observation is the velocity fluctuates vigorously near the wall due to wall effect. Compared to axial velocity, the radial velocity distribution is smaller and more complicated. The basic pattern is that on a given cross section of the column radial velocity increases from the wall to the center and it the velocity changes greatly around the center. Under the condition of column height less than 0.8 m, the axial velocity is negative and it directs from the wall to the column axis. When column height is higher than 0.8 m a reverse pattern is obtained, i.e., axial velocity is positive while directing from column axis to the wall. Special efforts were directed to investigate the tangential velocity pattern. Results indicate that the tangential velocity patterns of different cross sections are similar and showed a symmetrical distribution. Tangential velocity distribution concluded two zones: outer whirlpool and inner whirl-pool. And, interestingly, it has been found that on different cross sections the highest tangential velocity always occurs at the same position of the cross sections.

Jan 1, 2014

By William Conger, Greg Schick

Grinding media consumption is a major cost variable in industrial mineral comminution circuits. Specifically, industrial SAG media consumption results from a combination of surface abrasion wear, media breakage, surface spalling and rejection size from the mill. Three main consumption rates; weight of media consumed per time, per kWh and per weight of ore ground are defined and compared. Recent industrial data has provided an opportunity to relate consumption in terms of weight of media consumed to weight of ore ground (g/tonne) and weight of media consumed per kWh of energy consumed (g/kWh) with SAG specific grinding energy consumed (kWh/tonne). Using relationships developed from this data it is possible to project SAG media consumption in future mineral comminution circuits.

Jan 1, 2014

By H. Palza, C. Ihle, S. Contreras

"Processing of minerals, particularly treatment of tailings, has been increasingly challenged by the presence of clays in the feed of thickeners. This occurrence is expected to become increasingly important given the nature of ore deposits currently being exploited and those that have been recently discovered. In sedimentation operations (solid-liquid separation), industrial flocculants often fail to coagulate clay-containing fines, generating supernatants with high levels of turbidity, thus implying operational problems. Recently, it has been reported that graphene oxide (GO), a graphite derivative with high oxygen-containing groups, could enhance the flocculation of clay systems, due to the interaction between clays and GO functional groups. In the present work, we investigated the effect of doping industrial flocculants (commercial polyacrylamide) with GO on the floculation of kaolinite suspensions in a solid-liquid separation stage. Separation performance was evaluated by studying flocculation kinetics using a focused beam reflectance measurement (FBRM) instrument, in a set of batch tests. A statistical analysis of the flocculation kinetics and floc population distribution was further carried out. Our results suggest the existence of a synergistic effect between the studied flocculants and GO. This effect is observed as a decrease of clay fine contents in the supernatant, thus improving solid-liquid separation eficiency for high clay containing tailings. INTRODUCTION Copper, given its mechanical, physical and chemical characteristics, is a critical material for the progress of society and so has been from early stages of mankind. Demand for this metal has increased due to the growth of cities and the technological explosion, leading to increase current mining production and reinforce the efforts in exploration for new deposits (Elshkaki et al. 2016). As copper-rich deposits are being depleted, it has been necessary to develop proper technology to mine deposits of lower grades and more complex mineralogies, keeping in mind that the economic window that allows the exploitation of them is reduced by the increase on operating costs (Crowson 2012 and Northey et al. 2014). High clay bearing minerals are found in many of those low-grade copper deposits, and they induce problems in all stages of the mineral processing route (Taner and Onen 2016). Particularly, in the solid-liquid separation stage, the flocculation process fails to remove the clay fraction from suspension and it leads to operational issues such as filter damage, overconsumption of reagents and the need to add an extra clarifying step for the recovered process water. Those problematics pose an interesting challenge."

Jan 1, 2018

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By J. Gebhardt, D. McBride, M. Cross, S. Gilbert

Heap leaching of ores containing chalcopyrite offers a low cost option to treat low grade complex copper sulfide ore bodies. However, the slow leach kinetics of chalcopyrite at ambient conditions typically results in unacceptably low recoveries. As the mineralogy of new ore deposits becomes more complex and the effects of gangue chemistry exert a greater influence on copper sulfide leach behavior, the control of leach reaction chemistry becomes more critical. Computational fluid dynamics (CFD) technology has been useful in the capture of multi-phase interactions and provides a path to simulate complex fluid flow, gas and liquid phases, through the heap, along with species transport. Coupling the flow models with the reactive mineral dissolution, and the sometimes competing aqueous chemical and solid-liquid reactions, yields a comprehensive model of the heap leach process. The leach kinetics of chalcopyrite dissolution in heap conditions is examined, and the incorporation of chalcopyrite leach kinetics in the CFD model is described. The application of the model to investigate optimization of the heap is discussed.

Jan 1, 2014

By Fiona Sofra, Briony C. Ruse, David B. Boger

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.Full Cost Accounting techniques may be used to provide financial justification for the implementation of alternative tailings disposal techniques through the calculation of a disposal cost per tonne of tailings over the life of the facility. Improved disposal methods such as thickened tailings disposal involve additional initial capital expenditure but reduce environmental impacts. The cost savings associated with environmental impact mitigation are reflected in Full Cost Accounting outcomes.Rheological characterisation is significant as a design basis that may be analysed using Full Cost Accounting to justify the initial capital expenditure of dry disposal systems for improved environmental performance."

Jan 1, 2003

By V. A. Ignatkina, V. A. Bocharov, T. I. Yushina, I. M. Petrov, A. A. Kayumov

"The purpose of this research was aimed at increasing recovery of metals from rebellious sulfide polymetallic ores of nonferrous and rare metal deposits. The ores under consideration have common processing features, including textural and structural complex characteristics, irregularity of impregnation and wide range of grain size, up to nanoparticle size, variable complex mineral composition, low content of precious metals etc. This all predetermines the need for advanced processing schemes with deep selective liberation and separation of minerals with intercycle release into rough concentrate and fractional products with the use of multi-stage cycles of individual dressing, based on an optimum combination of various integrated beneficiation and hydrometallurgical processes. The application of existing standard processes does not enable the production of high-grade selective concentrates without reducing the recovery rate due to incomplete separation of fine mineral intergrowths and overgrinding of brittle ore and rock minerals.The combined beneficiation processes for such type of resources, aimed at increasing recovery of nonferrous, rare, and precious metals are based on flotation methods in combination with gravity concentration to produce rich rough collective or selective concentrates, comprising readily floatable mineral fractions. At the same time, hardly recoverable and non-separable mineral associations are released into separate concentrated products for following dressing by individual processes. The proposed combined process provides for successive selective liberation of minerals with release of rich readily recoverable mineral fractions at the preparation and ore beneficiation stages. The hardly recoverable mineral associations shall be released in subsequent operations with the use of dressing, based on a combination of beneficiation and pyro- and hydrometallurgical methods."

Jan 1, 2018

By Graeme Jameson

"In current flotation circuits it is customary to grind the whole of the mill feed to an initial size, which is determined by the liberation characteristics of the ore, and the ability of the flotation machines to float the fully liberated particles. Usually, the product of the primary mill will be ground further in a ball mill, to improve the liberation of the values and hence the product grade, before passing to rougher flotation cells. The final grind size is ore-dependent, and is a balance of factors including the relation between surface liberation and grind size, the grain size of the valuable particles within the host rock, and the feed grade. The P80 for the feed to flotation may be as high as 300 µm for free-milling copper ores, and as low as 53 µm for finely disseminated complex ores. The grinding of the feed ore requires considerable input of energy. The rate of replacement of wear components such as mill liners and media, is proportional to the energy input. The costs of these two factors - energy and wear - are usually comparable and together they form the major part of the running costs of a concentrator, and indeed, of the whole mining operation. The energy required increases as the final grind size decreases. This talk will focus on the reduction of milling costs that could be achieved, using a fluidized bed flotation technology that can give high recoveries at coarse particle sizes. A number of different circuit designs will be presented, using the new technology. Calculations show that reductions in the running costs of a mine and associated concentrator of the order of ten to twenty percent could be achieved."

Jan 1, 2014

By J. R. Cui

The production of electric and electronic equipment (EEE) is one of the fastest growing areas. This development has resulted in an increase of waste electric and electronic equipment (WEEE). In view of the environmental problems involved in the management of WEEE, many counties and organizations have drafted national legislation to improve the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. Recycling of WEEE is an important subject not only from the point of waste treatment but also from the recovery of valuable materials. Consumer electronic equipment (brown goods), such as television sets (TV), radio sets, and video recorders, are most common. However, recent work on recycling of waste electric and electronic equipment (WEEE) primarily focused on personal computer and printed circuit boards scraps. Based on a detailed characterization study of consumer electronic scraps, recycling of TV scraps oriented to recovery of metals is highlighted by utilizing air table separation, eddy current separation, and optical (metal) sorting process. The result indicates that a high recovery of copper could be obtained by utilizing an effective gravity separation process. The separation results reveal that air table separation is an effective technology to recover metals from consumer electronic scraps. By using a DGS table, approximately 90% of non-ferrous metals were recovered in the heavy product with a purity of 40%. Printed circuit boards and cables in TV scrap cause metals loss due to the fact that metals in printed circuit boards and cables are not liberated from plastics and ceramic materials. The study shows that eddy current separation and optical (metal) sorting process provide alternatives for recovery of metals from shredded TV scraps.

Jan 1, 2014

By Slobodan B. Vujic

"For the requirements of the mining company “Rudnik-Rudnik”, engaged in undergr-ound exploitation of polymetallic ore and lead, zinc and copper concentrates production, the Department of Computer Application of the Faculty of Mining and Geology, University of Belgrade, designed a computer supported and integrated information-management system. This paper presents a concept of this system covering both monitoring and management of production in ""Rudnik-Rudnik"".The ""Rudnik"" Rudnik, Yugoslavia is a mining company, engaged in underground exploitation of polymetallic ore and production of ore, zinc and copper concentrate as well as other metals such as silver, bismuth and cadmium. This mining company runs stable business activities and undergoes a permanent growth of valuable production volume.The basic characteristics of production-technical system of ""Rudnik"" company are: uniform and up-todate technical-technological solutions: linking of production chain from underground exploitation of ore to flotation, namely final product - concentrate of lead, zinc and copper; complete mechanization of production; relatively low level of computer technics implementation; namely, ununiformed implementation of different application of computer-supported information technologies in production and business activities of the Company.These are the assumptions on the basis of which the management of the Company made a decision, in 1999, to upgrade information-management functions through development and application of modern integrated and computer-supported production-business information-management system (hereinafter: IMS, namely IMS Rudnik). For this purpose the Company requested the Department of Computer Application, Faculty of Mining and Geology, University of Belgrade to make the Project on IMS for their needs."

Jan 1, 2003

By Xin Tan, Changgen Li

"The floatabiliby of chelate CF-collector for zinc and lead oxide minerals was described. It found that CF-collector possesses a strong collection power for zinc and lead oxide minerals as well as excellent selectivity for the gangue minerals. A new technology of zinc and lead oxide flotation with CF reagent as a collector, lead nitrite as a activator and water glass as modifier was presented. The mechanism of interaction between reagents and minerals was discussed by means of adsorption, zeta potential, nephelometric titration, XPS and infrared spectra was investigated.CF-collector, newly developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM), is a kind of chelate collector for the flotation of oxide minerals. CF-collector mainly consists of N-nitroso-N-phenylhydroxylamine ammonium salt. The CF-collector was used for the selective flotation of scheelite in the Chinese plants.In this paper, the effects of the dosages of activator Pb(NO3)2 and depressants (sodium hexametaphosphate, polyphosphate, water glass and salified water glass) on the floatabilities of several minerals (cerussite, smithsonite, calcite, dolomite, limonite and quartz) as well as their mixtures were investigated in the presence of the CF-collector. The results show that the CF-collector is the excellent collector for selective flotation of cerussite and smithsonite. Pb(NO3)2 can selectively activate the oxides of lead and zinc resulting in a decrease of the CF-collector dosage. The sodium hexametaphosphate plus the salified water glass are the effective depressants for gangue minerals. Based on the above facts, the “CF process”, namely, used CF reagent as a collector, Pb (NO3) 2 as a activator, and sodium hexametaphosphate plus salified water glass as depressant, has been used for the flotation separation of the lead oxide mixtures or zinc oxide mixtures without disliking and heating. For the feed lead assaying 19.07%, the lead concentrate assaying 49.81% Pb at the recovery 80.69% was obtained after one step flotation. For the feed zinc assaying 12.85%, a zinc concentrate of assaying 29.56% Zn at recovery 83.87% was obtained."

Jan 1, 2003

By Marco Le Roux, Martha Van Rensburg, Quentin Campbell

Fluidised bed drying is currently receiving much attention as a dewatering option during the beneficiation of fine (defined here as between 1 mm and 2 mm particles) coal. Apart from concerns about safety and combustion, the operating costs can be high if very high gas or air temperatures are used. The aim of this study was to investigate the removal of moisture from fine coal by using air at a lower temperature (25 - 55°C) within a controlled environment by lowering of the relative humidity of the air. It was firstly proven that fluidization has a major advantage over non-fluidized beds, with regards to drying rate and final moisture content. Hereafter several parameters that influence the dewatering rate and final moisture content were tested, from which it was concluded that the relative humidity of air acts as the largest driving force for dewatering. Parameters tested included relative humidity, temperature and coal composition. Energy balances showed a positive nett energy increase in the dried coal during combustion when related to the energy input during drying. In comparison with thermal drying technologies, fluidized bed drying was proven to be less energy intensive. It was therefore shown that this is a viable technology for the dewatering of fine coal.

Jan 1, 2014

By Ronald Díaz

"Cerro Corona is a porphyry ore with different geometallurgical units and alterations produced by an extensive family of geological failures that have determined a special type of mineralization. With the increasing depth of the mine, it is estimated that the host rock will be less altered. Consequently, the ore will have a higher resistance to breakage accompanied by associated problems such as lower throughput. In light of this reality, various projects have been carried out with the objective to optimize mineral processing of ore with low clay content and high hardness, including reducing the blasting grid, increasing the load factor, using adequate mixtures of hard ore, reducing crusher settings, installing air guns in the transfer chutes, increasing ball charge, and changes in the lifter design, wear control in the hydrocyclones, syntonization of control logics, supervisor control of the SAG mil, characterization of feed ore, etc. However the most important factor was the teamwork between mine and plant personnel, aiming at common objectives for the company. These projects started in 2011, including characterization of mineralogical domains, breakage and blasting characteristics, and also a revision of the actual operating conditions in the crushing and grinding circuit. The development of different designs of the SAG mill lifters and the unloading grates, a 16% ball charge increase, improvements in the blasting process, reduction of the primary crusher setting, weight reduction on the feed lid, and variation of operational parameters, all allowed the company to achieve its objectives of maintaining impact control and steel recharge within the expected operational parameters. The achieved throughput is above design capacity, sustainable, and not without new challenges for maintaining and optimizing this production level."

Jan 1, 2014

By J. Kwon, D. Lee, H. Cho

"The use of the combined grinding and liberation model to predict liberation characteristics of iron ore comminuted by a ball mill was studied. Comminution characteristics were obtained using the one-size fraction method. The iron ore samples were crushed and separated into a number of narrow size fractions by screening. The size fractions were further divided by magnetic separation into three classes: concentrate, middling, and tailings. Subsequently, various size-grade classes were subjected to ball milling, and the results were analyzed in terms of the kinetic grinding model. The mineralogical textures of the grinding products were analyzed using mineral liberation analysis. The distribution of iron content within the size fractions was characterized by the beta distribution combined with the Andrew–Mica diagram. It was found that the grinding characteristics of the iron ore samples varied slightly with the iron content. However, the liberation characteristics were well described by the same set of liberation model parameters, regardless of composition. The variation in grinding kinetics with composition and the liberation model parameters was used in the combined comminution–liberation model to predict the evolution of the size-composition matrix as grinding proceeded. The predicted results agreed well with the experimental results. The developed model can be used to construct the yield–recovery graph and to calculate the liberation efficiency to determine the size reduction threshold for efficient separation. INTRODUCTION In mineral processing, comminution is usually the first step that ores undergo to liberate valuable minerals from gangue minerals. Generally, as the particle size decreases, higher liberation can be achieved. However, excessively small particles are unfavorable to subsequent processes, such as separation. Moreover, comminution is a highly energy-consuming process itself that accounts for approximately 60% of all energy used for processing. Therefore, there is a definite need to increase energy efficiency by applying adequate stress so that a high degree of liberation can be acquired at the coarsest size without overgrinding. To this end, it is essential to develop a model to predict the liberation of minerals as a function of size reduction."

Jan 1, 2018