Search Documents

By H. W. Wevers

This paper is the result of an intensive literature search and practical study of the problems experienced by a mining company with the frame cracking of their large-tonnage haulage trucks. It explains the advantages of particular HSLA steels for applications in the welded structures of such equipment. Examples of existing welds in truck frames are analyzed. Modern fatigue models and linear elastic fracture mechanics techniques are explained.

Jan 1, 1978

By H. H. Bleakney

THIS paper presents evidence that in 3 1/2% nickel steel, the published temperature for the Ac1 transformation, l,275°F., represents the completion of that transformation, and that its inception occurs approximately 275°F. lower, at about l,000°F. The formation of austenite within this range, especially at the higher temperatures, and its subsequent decomposition to martensite, results in considerable impairment of the properties of the steel. That the solid solution found to occur below l,275°F. is austenite has been questioned, but the evidence herewith presented, while not decisive, appears to be reasonably convincing. INTRODUCTION The February, 1939, issue of Metals Technology contains a very interesting paper by I. N. Zavarine, Associate Professor of Metallurgical Engineering at the Massachusetts Institute of Technology. In that paper, Professor Zavarine presented photomicrographs illustrative of the microstructures produced by heating nickel steels to a temperature slightly below the carbon change point, and holding them at that temperature for various lengths of time. His illustrations show that the structures found after such treatment do not consist merely of ferrite and carbides, but are characterized by the presence of a third phase, which he describes as a' 'sub-critical solid solution'. The occurrence of this third phase in increasing amounts is accompanied by an increase in strength and a loss of ductility and impairment of elastic ratio of the steel. Some years ago, one of the authors encountered the above-mentioned phenomenon in treating large forgings of 3.5% nickel steel. After normalizing and then drawing at l,250°F., very poor mechanical properties were obtained. Investigation of the steel disclosed no inferiority in quality. Eventually, after considerable waste of time and money, a draw temperature of l,150°F. was tried. This treatment resulted in a very great increase in elastic ratio, over 5 per cent increase in percentage elongation, and proportionate improvement in reduction of area.

Jan 1, 1941

By R. J. Young, S. J. Tennant, A. D. Drummond

"Gibraltar Mines is located on the western slope of Granite Mountain, 230 air miles north of Vancouver, B.C. and 38 miles north of Williams Lake, B.C. There are four mineable zones within the copper-molybdenite deposit: Gibraltar East, Gibraltar West, Pollyanna and Granite Lake. Open-pit reserves are 358 million tons which average 0.37% Cu and 0.016% MoS2 at a 0.25% Cu cut-off. The Granite Mountain pluton is one of the several Jurassic-Cretaceous intrusions which outcrop along the east side of the Fraser River fault system between Williams Lake and Prince George, B.C. The original Granite Mountain quartz diorite has been metamorphosed by a cataclastic deformation which foliated the rock on a regional scale. Attendant to the development of the foliation, the rock was saussuritized such that the present mineralogy is compatible with that of the greenschist facies. The presence of garnet-bearing assemblages is explained by a restricted increase in water pressure. Pre-mineral intrusive phases within the saussuritized quartz diorite are: (1) leucocratic quartz diorite, (2) aplite and (3) quartz-feldspar porphyry. A late chloritized hornblende dacite dyke is post-mineral. Quartz-feldspar porphyry and leucocratic quartz diorite are locally present on the inner sides of the Gibraltar East, Pollyanna and Granite Lake pits. Their presence suggests a core around which occurs an elliptically shaped sulphide-bearing stockwork. The stockwork, which comprises four ages of vein development, is imposed on and partly controlled by the regional foliation of the samssuritized quartz diorite."

Jan 1, 1973

By S. Kaushik

The control room in a mineral processing plant has become increasingly complicated with complex unit operations coupled with rapidly evolving systems of sensors and control. Even with significant automation, human intervention is required to counter various scenarios that play out every day. A typical control room operator must monitor over 300 individual points of data in order to ensure the safe and efficient operation of the plant. At the same time, the experience of the workforce is decreasing as operators retire and the new generation enters the concentrators. Global competition for skilled operators continues to be strong and the opportunity to apprentice has diminished. The challenge is to provide a skill foundation for the operators so that they can be effective in the concentrator in a timely and safe manner. Progressively, the industry is turning to dynamic simulation tied into the control system. The simulator environment operates behind the control system to emulate the plant operation, reacting as the plant would when a change is made. The operator drives the process, with realistic feedback, which enables learning in a safe environment. This paper will take the reader through a green-field case study and discuss the effectiveness of integrating an operator training simulator (OTS) on the operator’s learning curve.

Jan 1, 2014

By Robert B. Parsons

"There is a widespread concern that certain of Finance Minister Michael Wilson's Tax Reform proposals will likely lead to a significant decline in flow through funding after 1988. This does not bode well for the junior exploration sector, which relies heavily on flow-through to finance exploration programs. The exploration industry is actively pursuing various solutions to the problems posed by Tax Reform, in order to ensure that flow-through has a future.IntroductionWhile the proposals contained in Finance Minister Michael Wilson's Tax Reform White Paper may not be as far-reaching as some people had expected, nevertheless the combination of the existing tax rules and proposed new rules offers sufficient complexity to keep pencils sharpened for many months. After having had an opportunity to study Tax Reform since June 18, 1987, the sharpened pencils are suggesting that the White Paper is not without its shortcomings and pitfalls. Insofar as the mineral exploration industry is affected, there is widespread concern that adoption of certain Tax Reform proposals could spell near disaster for mineral exploration in Canada. More specifically, there seems to be a consensus among the industry, as well as some federal and provincial government officials, that the announced phase-out of the ""mining exploration depletion allowance"" (MEDA) would reduce the appeal of flow-through shares to the point where only a fraction of exploration funding would be financed in the future by flow-through."

Jan 1, 1987

By J. R. Fisher

"Uranium may be leached to some extent in situ from the Blind River conglomerate uranium ores by using the products of bacterial activity from the bacterium Thio-bacillus ferrooxidans his paper describes some of the laboratory techniques used to investigate the characteristics of the bacteria, and to utilize their properties in uranium leaching. The application of some of the laboratory results underground at the Milliken mine of Rio Algom Mines Limited are de-scribed, along with the method of uranium recovery from the mine waters."

Jan 1, 1966

By Jacek Paraszczak

As the deposits located closer to the surface are getting depleted, more and more Canadian mines produce ore from considerable depths. Deep mining represents a number of serious challenges including high rock temperature. Conventional diesel powered loadhaul- dump machines and trucks so widely used in metal mines constitute an additional source of heat and noxious gases. Due to this, they have a substantial adverse impact on a quantity of fresh air required and a cost of ventilation, particularly since the mines have to meet more and more stringent regulations in this respect. In this context, the paper examines possible alternatives for diesel powered equipment, both these commercially available as those at the stages of prototypes or under development. They are reviewed with regards to their principles, required infrastructure, stage of technology development and its progress. The questions of their flexibility, practicality and economic viability are also addressed. Following the above a potential for their implementation and possible benefits (if any) in the conditions of deep Canadian mines is discussed. The paper concludes with short to medium term predictions concerning the most promising drive alternatives for vehicles destined to operate in deep metal mines.

Feb 1, 2008

By T. Fekete, D. L. Flocks, R. T. Hart

The plugging effect of bacteria was investigated by injecting various concentrations of dead bacteria cells though sandstone cores. Pressure profiles along the cores were recorded periodically during the injection cycles. The plugging effect was analyzed using a plot of the ratio of reduced permeabilities to the initial permeability versus input volume. Results indicated that Tock permeability has little effect on plugging, but that the concentration of bacteria in the injection water has a significant effect on plugging characteristics. The pressure profile curves showed that bacteria penetrated several inches through the core but that the greater portion of the bacteria accumulated at the in-put end of the core.

Jan 1, 1960

By G. Binks

In 1997, the Zinifex Hobart Smelter ceased ocean disposal of jarosite and the flowsheet was converted to reject iron as paragoethite. This paper describes the evolution of the flowsheet since the changeover and considers future flowsheet developments. The major change to the flowsheet has been an increase in the silica content of the calcine resulting from treating increasing levels of Century concentrate. The high silica levels impacted on the paragoethite precipitation stage, causing a deterioration in the settling and filtration characteristics of the paragoethite and an increase in the contained zinc level. The implementation of a two stage neutral leach step has enabled the flowsheet to cope with the higher input silica levels. Future developments include an understanding of the form of the zinc in the paragoethite and options to lower the zinc level to improve the overall zinc recovery.

Jan 1, 2006

By Mohan R. Srivastava

- OUTLINE - apologies and explanations - a quick bit of history - the wisdom of Wikipedia - ?Matheronian geostatistics continued to convert Bre-X?s bogus grades and Busang?s barren rock into a massive phantom gold resource?? - variogram analysis for Busang - would variogram analysis (or variance analysis) have revealed the fraud? - what went right, what went wrong

May 1, 2007

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By H. Huang, R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic to neutral solutions, over the pH range 1-7, to determine a potential range for co-dissolution. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated EH-pH diagrams for the copper-arsenic-sulfur-water system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Jan 1, 2014

By Edward R. T. Tiekink

Metal complexes continue to find therapeutic applications for the treatment of a wide variety of human ailments. Amongst these, gold(I) thiolates are used to treat rheutmatoid arthritis but, usually in combination with other treatment or as a last resort. New therapeutic uses of gold, both as gold(I) and gold(III), are being sought, including against cancer, the focus of the present contribution. It will be demonstrated that certain gold(I) complexes show exciting cytotoxicity profiles, rivalling those of cisplatin and standard chemotherapeutic agents. More importantly, anti-tumour activity is demonstrated in vivo, albeit in a mouse model. The presentation will give a brief overview of ?metals in medicine? with a focus on gold and will summarise some recent advances in the development of goldbased anti-tumour agents.

Oct 1, 2003

By M. Matsuda

The Hitachi refinery of Nikko Smelting & Refining Co. Ltd. began its electrolytic copper refining operations in 1911. In December 2002, the refinery changed its operation scheme by introducing the ISA permanent cathode technology for the first time in Japan. The change resulted in higher productivity, better cathode quality, and lower operational costs. The operation has been continuously improved to reach a 20% higher production capacity than the original one. For the electrolyte purification process, the Hitachi refinery has developed a new process for removing impurities. The process involves As, Sb and Bi adsorption from the electrolyte by means of chelating and ion exchange resin. The new resin process will achieve higher efficiency in removing impurity.

Jan 1, 2007

By Perry L. Christian

"Mana/ta Coal Ltd. 's Costello Mine, located seven kilometres east of Estevan, Saskatchewan, has been operating at the present location since 1960. During the past twenty-three years, annual production of lignite coal has averaged 590 000 tonnes. The coal is used for power generation and for industrial and domestic use. Markets, operating techniques, facilities in place and reclamation are discussed. Introduction The Costello Mine (formerly the Klimax Mine) is located in southeastern Saskatchewan, approximately 210 kilometres southeast of Regina and 5 kilometres from the United States' border, as shown in Figure 1. The present mine, 7 kilometres east of the city of Estevan, has been operating since 1960. The history, however, of the Costello Mine and of the Estevan Coalfield dates from the initial settling of the area in the 1880s. Mining initially consisted of burrowing into the side of the Souris River Valley or other hillsides where the coal seam was exposed. Eventually, slopes were put down in the Estevan/Bienfait area and vigorous underground activity existed. In the late 1920s surface strip mining was introduced. The use of strip mining progressed to the point where it completely replaced underground mining in the 1950s and it is the only method in use today. During the past 23 years annual production has averaged 590 000 tonnes. The lowest production was in 1960 when the mine was starting up at 167 000 tonnes and the highest production was in 1977 when production was 1 509 000 tonnes. The Costello Mine controls approximately 11 400 hectares of mineral rights in the Estevan area. This is made up of 4 900 hectares of freehold coal and 6 500 hectares of leases. The area forms a large, irregular shaped configuration. Most holdings are contiguous and adjacent. The mine also owns some 8 400 hectares of surface rights. The lands under the Costello Mine's surface rights control, which are not being used in the mining operation, are leased to local farmers and ranchers. This ensures that the land is used to its full potential, both before and after mining."

Jan 1, 1985

By L. Zeng, Q. Feng, Z. Qiu, L. Ou, Central South University

It is well-known that the use of nanobubbles can significantly improve the flotation efficiency of ultra-fine particles. However, this is mainly focused on coal and phosphate rock flotation. In the field of nonferrous metal processing, the related research is few. In this paper, a small laboratory mechanical cell associated with a specially-designed nanobubbles generator was used to investigate the effects of nanobubbles on enhancing ultra-fine scheelite flotation. Nanobubbles were created and based on the hydrodynamic cavitation principle through Venturi tubes. Comparative flotation tests were performed using different tubes to evaluate the nanobubbles impact on the ultra-fine scheelite particle flotation recovery. In order to better understand the nanobubbles enhanced ultra-fine scheelite flotation, nanobubbles potential and size distribution were measured. The effect of nanobubbles on the particle aggregation and scheelite particles potential were also studied through the turbidity tests, microscope tests and zeta potential measurements. According to the results, the mean size of nanobubbles was about several hundred nanometers, and the surface of nanobubbles was of highly negative charge in alkaline conditions. The flotation recovery of ultra-fine scheelite particles was increased in the presence of nanobubbles. The zeta potential measurements indicated that the repulsive forces between scheelite particles decreased when nanobubbles existed. Through the turbidity tests and microscope tests, the promotion effect of nanobubbles on particle coagulation could be verified more directly. The existence of nanobubbles in flotation system promotes the particle aggregation, thus increasing particles apparent size and particles capture by bubbles, which may be the fundamental reason why nanobubbles enhance ultra-fine scheelite flotation.

Jan 1, 2016

By Somchet Vongpaisal

This paper presents the R&D results on the development of a new knowledge-based system for predicting stope instability and associated unplanned dilution in deep underground mining operations. A new prototype was developed based on databases generated from 3D non-linear elasto-plastic finite element stress analysis, heuristic rules, and case histories. This prototype aims to assist mine operators to make decisions on strategic mine planning and feasibility in a quick and efficient manner thereby minimizing risk on ground failure and optimizing mining costs.

Jun 1, 2012

By A. Alfantazi, E. Asselin

"The corrosion of commercially pure titanium (CP-Ti) was studied from room temperature up to medium temperature (~160°C) under conditions relevant to medium temperature chalcopyrite leaching processes. The corrosion rates were measured by immersion and electrochemical tests in sulfuric acid. The influences of chloride, cupric and ferric ions on the corrosion rate and behavior were also investigated. Corrosion of the CP-Ti did not account for the total current density measured by linear polarization tests. The corrosion rates of CP-Ti under medium temperature leaching conditions were surprisingly high. The corrosion rate measured in ferric containing solution at 160°C was approximately 20 mm/yr.INTRODUCTIONTitanium exhibits excellent corrosion resistance in many aggressive environments because of the formation of a very chemically stable, highly adherent, and protective oxide film on its surface (Mitsuo et al., 2002). Because titanium is the only metal available at a reasonable cost that resists the high temperature corrosive slurries in many leaching processes, it is often chosen as autoclave liner material where it is subjected to severe conditions of acidity, temperature and pressure (Grauman and Say, 2000).A number of distinctly different hydrometallurgical processes for the pressure leaching of chalcopyrite have been developed and patented by various companies and they can be classified into low, medium and high temperature regimes (McDonald and Muir, 2007). For example, chalcopyrite concentrate may be processed at medium temperatures (115-175°C) and pressures of 800-2200 kPa (Dreisinger, D., 2006; Sahu and Asselin, 2011). The lixiviant may contain 20 to 55 g/L sulfuric acid, 8 to 12 g/L chloride ions, 10-25 g/L Cu2+ (Jones, 1995, 1997, 1999), and less than 1 g/L Fe3+ (Defreyne et al., 2005). The amount of these additions is determined by the grade of the ores and details are shown in Table 1."

Jan 1, 2012

By Yin Wang, Lin Li, Zhongwei Bi, Like Wei, Wen Li, Shaogang Li, Bin Zhang, Hongjie Li

Presently,Many long-wall fully-mechanized faces in shallow depth coal seams are below room and pillar goaf in Shendong mining area. When the working face is advanced out of concentrated coal pillar in upper room and pillar goaf, strong strata behaviors often cause support crushing accident. Aiming at a support crushing accident which happened in Shigetai coal mine of Shenhua group in Shendong mining area, this paper analyses the stress transfer process while mining out of concentrated coal pillar by numerical simulation software FLAC3D. According to the feature, simplifying the roof of upper room and pillar goaf as supporting-beam structure explains mechanism of large area collapse in room and pillar goaf roof. Based on the feature of supporting-beam structure, deep-hole blasting concentrated coal pillar technology is proposed to control the strong strata behaviors in Shigetai coal mine. The blasting control effect is confirmed through characteristics of strata behaviors, growth circumstance of ground crack and multi-point extensometer monitoring results. By using control technology, Shigetai coal mine has been successfully avoided support crushing accident.

Jan 1, 2015

By M. Côté, H. Pépin, Y. Richer, C. Gingras

Rolls-Royce Canada has been nominated as a Rolls-Royce Center of Excellence for repair of fan blades in 2003. One of the challenges of the Rolls-Royce Canada Component Repair Center of Excellence team is to reduce cost and time of inspection while ensuring trace ability and quality of the inspection performed on the fan blades. In the context of the dimensional control process optimization, and following the positive conclusions of initial trials carried out in 2003, the technical authorities at RRC have selected the SPG data 3D(TM) technology as a development base for dimensional control programs. The main goal of this development initiative is to develop and support an inspection system to perform the dimensional control and inspection of different components at the Montreal Fan Blade Repair Center of Excellence. The final objective of the program is to build a server platform capable to support different inspection sites within the Montreal facility for the future. This paper presents the certification process of the technology according to the VDI-VDE 2633 certification standards and some results of the fan blade inspection program of the BR 710, BR 715 and TAY according to the JES 195 engineering standards specification.

Jan 1, 2006