Search Documents

By John Ramsay, Frederick A. Edwards, J. Eric Belford, Clarence V. Amyotte

"DEVELOPMENT of the underground mine is carried out from a main ramp driven from surface to the 800 and 1200 levels and from a shaft sunk to 3050 ft. Sub-levels at approximately 100-ft vertical intervals, starting 300 ft above the 800 level, were collared from the ramp as it advanced and a considerable amount of development work was pursued. The lateral and ramp work provided an opportunity to train drift crews, test equipment and methods, assess ground conditions and advance the initial stope development. The development of an exhaust ventilation raise system closely followed the extension of the level development to the south end of the orebody (Fig. 26) . On completion of the shaft, temporary lip pockets were installed at the shaft stations on the 800, 12.00, 1600, 2000 and 2400 levels. The permanent loading pocket had been installed on the 2860 level as part of the shaft-sinking contract and the level had been connected to the 2800-level station by a small muck transfer raise. Development of the 2800-level area was given top priority at this stage. This included a 1000-ft cross-cut to the crusher location, the crusher excavation, storage bins, conveyor ways and a ramp to connect the 2800 level to the loading pocket, the rope changing station and the shaft sump. The development and installation of the rock handling system between the 2400 level and the shaft bottom was contracted to Macisaac Mining and Tunnelling Company, of Sudbury, Ontario."

Jan 1, 1974

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By M. Girard, E. Bourricaudy, M. Ashbury, M. Canizares, A. Mezei

Liquid-solid separation and slurry handleability relate directly to commercial plant ramp-up success or lack thereof. The paper provides a well-proven approach for testing, scale-up and commercial application of difficult processes. Emphasis is placed on practical applications of rheological concepts developed both academically and empirically. The cause-effect relationship between the process chemistry and possible physical implications on the metallurgical plant operability is presented in a simple, direct form. Examples include recent results in areas of mineral processing and extractive metallurgy. Technical process risk factors and their mitigation are included in the discussion.

Jan 1, 2011

"Liberation is a key requirement for efficient separation in mineral processing. As a consequence of this an understanding of the inherent textural features of an ore is no longer possible since during the process of liberation, texture is destroyed. Knowledge of key textural features, such as mineral grain size and distribution, prior to breakage processes provides the opportunity to understand the textural drivers for ore hardness. Modern characterisation methods, including automated SEM-based techniques, provide the possibility of measuring mineral characteristics at a range of scales. This paper discusses how textural features of two different ore types in a porphyry copper deposit can be measured and interpreted at a number of scales. Standard breakage tests conducted on the ores indicate that one of the ores can be characterised as hard and the other as soft. The impact of mineral grain size and the presence and scale of vein type structures in the two ores have been used to determine the extent to which these features influence ore hardness.INTRODUCTIONIn order to effectively convert ore into metal, knowledge of both the processing stages and the characteristics of the ore are essential. Prior to the advent of technologies that enabled the fundamental understanding of the sub-process at each stage of processing and the measurement of appropriate ore properties the most effective way to understand how an ore would respond to a process was to put it through that process, for example the way to determine how an ore would break was to first break it. Existing comminution models seek to predict the size distribution of rock fragments as the result of applied energy based on knowledge of the rock strength. It is common for these models to consider the rock as homogeneous and despite providing important data for the design and optimisation of industrial comminution circuits these models are only applicable within a narrow range of operation. In order for reliable predictive models to be developed that account for the inherent ore characteristics, a step change is required in the type of measurements that are carried out to characterise an ore and the type of data that is extracted and used as model inputs."

Jan 1, 2016

By C. M. Kleemann

The paper describes the present milling practice at Western Mining Corporation Limited's new nickel mine at Kambalda in Western Australia. It details the crushing, autogenous grinding, flotation and spray drying circuits for the production of a nickel concentrate. It also indicates some of the metallurgical problems which have been encountered in concentrating this ore.

Jan 1, 1973

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By W. H. Gauvin, N. J. Themelis

I N ADDITION to its practical importance in the beneficiation of iron ores and in direct-iron processes, the study of the reduction of iron oxides involves many aspects of challenging theoretical interest. The complexity of the reduction process combined with the fact that under different experimental conditions the controlling stage for the reaction may not necessarily be the same, has led experimenters in this field to a wide diversity of opinion regarding the reaction mecl1anism. As a rule, each investigation has been restricted to the study of one or two variables over a comparative]~• narrow range of experimental conditions, and consequently, it be-comes necessary to examine the significance of each published work in the light of the results of other experimenters in the field.

Jan 1, 1962

By J. -F. Lepage, M. A. Tomlinson, K. K. Murray

"The Éléonore mine, located in the James Bay region of Northern Quebec, generates a gold bearing flotation concentrate rich in pyrrhotite. Direct leaching of the finely ground concentrate results in high cyanide consumptions and poor recoveries, so effective pre-treatment to passivate the pyrrhotite is required before leaching. Following a number of process upsets at the mine, test work was performed to better understand the requirements for passivation so a more effective operational strategy could be implemented. This paper outlines the testing and implementation of the new strategy at Éléonore.ÉLÉONORE CONCENTRATOR The Éléonore mine is located 800 km north of Montreal, in the James Bay Region of Quebec, Canada. The ore, containing gold disseminated in sulfide minerals and free fine gold in silicate gangue, is crushed in a two-stage crusher plant before being ground in a single 9,000 kW ball mill. The ball mill is in closed circuit, with about 25% of the cyclone underflow passing through a gravity plant with two, 48” Knelson concentrators. Gold recovery in the gravity circuit varies between 15 and 20%, with gravity concentrate leached daily in an Acacia intensive leach reactor. Cyclone overflow, at a target P80 of 65 microns, flows to the flotation plant where the gold bearing sulfide minerals, mainly pyrrhotite and arsenopyrite, are recovered to concentrate with a mass pull of about 5%. The flotation concentrate, typically containing between 80 and 120 g/t of gold, is thickened and finely ground using a 1500 kW Isa Mill. The finely ground concentrate is diluted, to generate a slurry with about 32% solids by weight, before feeding the leach plant. Initially the concentrate slurry is pre-treated with oxygen and lead nitrate, to passivate the sulphide minerals before cyanide is added for gold dissolution. Gold is recovered from the leached slurry using carbon-in-pulp (CIP). The flotation tailings are also thickened and gold is recovered in a dedicated leach-CIP plant."

Jan 1, 2017

By F. Siciliano, D. Bai, S. Yue, A. M. Elwazri

The influence of niobium addition and very low temperature (`cool') deformation on the microstructure and properties of low carbon microalloyed steels was investigated. In this work, the specimens were heated at 1200°C and held at this temperature for 20 minutes. Some specimens were aged at 400°C for times ranging from 10 minutes to 10 hours followed by air-cooling. Others were subjected to deformation at 400°C (`cool deformation') prior to aging. It was observed that the proportion of acicular ferrite was increased as the amount of Nb was increased. It was found that cool deformation increased both yield and tensile strengths significantly compared to that of the aged only specimens.

Jan 1, 2005

By K. Shen, A. J. Sinclair, N. Champigny

"Fluid inclusion studies from the Cinola deposit indicate low salinities and low C01 contents of the ore fluid. This supports a suggestion that the mineralizing fluids originated from pore water in the fluviatile host rock (mid-Miocene Skonun Formation). Bimodal distribution of filling temperatures suggests the existence of at least two temperature regimes centred on 160°C and 270°C during mineral deposition. Independent age and stratigraphic evidence indicates that depth of mineralization is between 1.1 and 1. 8 km, corresponding to a hydrostatic load of between 110 and 170 bars.RESUMELes donnees sur les inclusions fluides du gisement Cinola indiquent de basses salinites et basses teneurs en C01 . Ceci confirme que les fluides mineralisants ont ete derives de l'eau interstitielle prise dans les sedimentsfluviatiles hates. La distribution bimodale des temperatures d'homogenisation implique !'existence de deux regimes de temperature concentrees vers 160°C et 270°C pendant Ia mineralisation. La profondeur alaquelle le gisement s'est forme est evaluee d'etre entre 1.1 et 1.8 km a partir d'informations stratigraphiques independantes: ceci correspond a des pressions hydrostatiques de 110 a 170 bars."

Jan 1, 1982

By A. Becker, C. Gauvreau, L. S. Collett

"A scale model was designed to simulate the airborne Barringer INPUT time domain electromagnetic system. The amplitude of the response to a vertical conductive dyke varies considerably with the conductor's thickness conductivity product (TCP). The response increases from a minimum detectable level at a TCP of about 2 mhos, rises to its maximum value at a dyke TCP of 15 mhos and then falls again so that conductors with a TCP exceeding 500 mhos would probably remain undetected. Measurements made with both standard receiver coil configurations (maximum or minimum coupled) indicate comparable effectiveness for both systems, either from the viewpoint of vertical conductor detection or from the viewpoint of discrimination against overburden anomalies."

Jan 1, 1972

By C. J. Newman, R. J. St. Eloi, G. Macfarlane

"The Kidd Creek copper smelter has been expanded from its original design of59000 tonnes of copper per year to over 120 000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and, generally, to optimize the operation.The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates. IntroductionThe Kidd Creek Division of Falconbridge Limited is a base-metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April 1964. Mining operations began in 1966 with a 9000 tonnes per day (t/d) concentrator corning on stream in November of that year. In April 1972, a 108 000 tonnes per year zinc plant was conunissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 t/d of ore. To expand zinc production, the world's second installation of the Commco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 136 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No. 3 tankhouse technology for the copper refinery."

Jan 1, 1994

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he's hurt. Maybe he's not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

Oct 1, 2010

By Zygmunt Kowalczyk

"A theory permitting the determination of expected surface deformations for planned underground exploitation is proposed and discussed in this paper. The relations between surface subsidence and various methods of mining are analyzed, and allowable horizontal .deformations for protected objects, according to the degree of their significance, are reviewed."

Jan 1, 1966

By George P. Demopoulos

For more than 20 years the author had the privilege of working closely on a number of R&D projects with Lucy Rosato and her team at CEZinc. Several of these projects were driven from the sustainability agenda that Lucy Rosato championed as an innovation leader that supported research collaborations. Highlights from this highly rewarding collaboration are to be presented in this paper. In particular we will deal with the following works-topics: (a) iron control via solvent extraction as alternative to jarosite precipitation; (b) production of high-density gypsum by controlled neutralization of simulated zinc plant process/waste waters; (c) selenium removal from weak acid solutions; (d) electrolyte purification by cementation; and (e) manganese control by oxidative precipitation with SO2/O2.

Jan 1, 2015

By P. Scinto, P. Hudson

"Modern day ore bodies are becoming increasingly harder, more abrasive and lower grade. The Mako deposit is located in Senegal and consists predominantly of primary mafic and felsic lithology that are both very competent and very abrasive ores (Axb < 30, BWi >20 and Ai >1.0). The deposit was initially discovery in 2010 and the Toro Gold management team fast tracked the Mako Project through development and into production to achieve its first gold pour in January 2018. The comminution circuit comprises primary crushing single stage SAG milling with recycle crusher (1oCR SS-SAC). The mill reached design throughput and grind size seven weeks after first ore. The Mako project marks another successful international application of single stage milling, which represents a simple and easy to operate comminution circuit for small-to-mid size projects with a low capital cost. This paper describes the ore interpretation, comminution modelling, grinding circuit selection and design, as well as an overview of the commissioning and ramp-up of the mill.INTRODUCTION The Mako Gold Project is operated by Toro Gold Ltd., which holds a 90% interest in the project. The project is located in south-eastern Senegal in the Kedougou region, close to the Gambia river and township of Mako. The Mako deposit lies in the “Kenieba Window” of eastern Senegal and western Mali, which hosts a number of gold mining operations and development projects. The Mako Gold Project has an estimated life of 8 years with overall recoverable gold estimated at 924 koz. The process plant is designed to treat 1.8Mt/a of ore and produce 128 – 143 koz of gold per annum. Lycopodium Minerals Pty Ltd (Lycopodium) was appointed to provide feasibility studies and EPCM services for the greenfield project. Forming part of consultancy services provided by Lycopodium, Orway Mineral Consultants (OMC), a subsidiary of Lycopodium, was involved in the design, commissioning, ramp up and ongoing post commissioning support of the comminution circuit."

Jan 1, 2019

By A. Deneys

This paper reviews industrial gases used in primary copper production. Copper smelting industrial gas demand has steadily increased since the first commercial oxygenconcentrate smelting in 1952 [1]. In copper production oxygen for smelting is the dominant industrial gas use followed by oxygen for converting. Nitrogen is finding increased use in copper smelters. Nitrogen is used for porous plugs for copper converting and anode refining [2-5]. Nitrogen can be used for concentrate drying [6,7] and is also used in some Ni-Cu smelters as a coolant in Peirce-Smith converting [8,9]. Industrial gas supply options of cryogenic or adsorbent based on-site plant or cryogenic liquid delivery are detailed.

Jan 1, 2007

By Mansoor Barati, Xue Yin, Yanhui Sun, Alex McLean, Yindong Yang

The formation and evolution of inclusions in Ti-Stabilized, 17Cr Austenitic Stainless Steel produced by the ingot casting process were investigated through systematic sampling of liquid steel and rolled products. Analysis methods included total oxygen and nitrogen contents, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results indicate that the composition of inclusions was strongly dependent on the types of added alloying agents. During the AOD refining process, after the addition of ferrosilicon alloy and electrolytic manganese, followed by aluminum, the composition of inclusions changed from manganese silicate-rich inclusions to Al2O3-rich inclusions. After tapping and titanium wire feeding, pure TiN particles and complex inclusions with Al2O3-MgO-TiOx cores coated with TiN were found to be the dominant inclusions when [%Ti] was 0.307 in the molten steel. These findings were confirmed by thermodynamic calculations which indicated that TiN inclusions could be formed in the liquid phase due to the high contents of [Ti] and [N] in the molten steel. From the start of casting to the rolled bar, there was no obvious change in the composition of inclusions compared to the titanium addition stage. Stringer-shaped TiN inclusions elongated along the rolling direction with lengths varying from 17 to 84µm were observed in the rolled bar, which could detrimentally impact the mechanical properties of the stainless steels.

Jan 1, 2015

The New Zealand opportunity NZ?s only significant phosphate deposit 1 million tonnes imported annually - mostly from Morocco US $180/t + $75/t freight

May 1, 2013

By D. -A Tremblay

Dynamic wetting spread factors and interfacial heat transfer coefficients were determined for aluminum droplets solidifying on copper substrates, The spread factors were determined from the droplet geometries while the heat transfer coefficients were obtained by solving inverse heat conduction problems, 1-D and 2-D heat transfer models are presented and the results they provided are compared, For the latter, a sensitivity analysis was also performed to determine the influence of thermophysical properties and boundary conditions. Experiments were alternatively carried out with three different gaseous atmospheres and the dynamic wetting spread factors were correlated to the interfacial heat transfer coefficients.

Jan 1, 2005