Search Documents

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

By Torres F, Cerda I, Gimenez P, Gonzalez G, Castelli L

Slurry density measurement, specially in cyclone feed streams, is fundamental to grinding circuit control. With the purpose of increasing the availability of such a measurement, the design of a soft-sensor in an actual grinding plant is addressed in this paper. The system is designed to substitute the momentary unavailability of the real density sensor, either because it has failed or because it has been removed for any other reason. The ARMAX model structure is determined using the stepwise regression method. Starting with a list of the candidate variables, the method selects, one by one, and in a systematic manner the variables which best model the measurement to be replaced, choosing them from the set of presumably correlated candidate variables. In this paper not only the single measurements are included in the list of candidates, but also combinations of such measurements having physical significance. A phenomenological model has been built with the purpose of determining these combinations. It turned out that in most of the cases the components of combined measurements having physical significance were selected by the stepwise regression method, instead of the single measurements. Actual grinding plant data is used to determine the model structure, to estimate the model parameters and to test the predictive capability of the developed soft-sensors. Good results are shown to be obtained during periods of up to 30 hours of the density soft-sensor operation.

Jan 1, 1995

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By Hellsten K, Eshuys E

The best long-term approach to exploration involves the use of extensive quality data and the integration of many different factors, methods and techniques. The successful exploration manager needs to integrate people, area selection and exploration methods, with the use of descriptive and genetic geological models. Based on a syn-metamorphic genetic model for Archaean gold, successful exploration in Western Australia requires the integration of data on anomalous gold, alteration, lithology and structure. Many other parameters such as geophysics, geochemistry and regolith studies provide additional, indirect information that needs to be integrated into the overall exploration programme. Timely access to research findings and ability to integrate these into immediate exploration has contributed considerably to the success of the gold industry in Western Australia since 1980. Extensive and deeper drilling, and the ability of computers to handle the volume of data generated have enabled effective testing of many more geological targets.

Jan 1, 1996

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

By P N. Martens

In the course of the development of the Report of the World Commission on Environment and Development (WCED) in the 1980s an expression was introduced in the public discussion on environment and development that influenced the international and national policies of the last 20 years in all areas: sustainable development. The UN decided in 1992 to implement a program with the Agenda 21 which contains the demand for developing indicators for sustainable development. In this context an indicator is understood as a quantitative or qualitative measure that can be measured or described throughout time and which moreover is able to depict the current status and changes. In order to enable for a simple holistic assessment of sustainable development, highly aggregated indicators are required, which integrate the criteria identified as relevant within a framework to be defined. In the presented paper, sustainability indicators for the mining industry are developed that account for the allowances of the sustainable development concept and the Agenda 21. The indicators are quantifiable and traceable through time so that developments can be traced and assessed. Furthermore, the indicators account for the multidimensional aspect of sustainable development. They are designed to allow for the integration of several dimensions in one indicator. The premises that are underlying the development of the indicators are the minimisation of negative impacts on the environment and society while simultaneously considering the maximisation of social and economic factors. Moreover, the participative momentum that is part of the sustainability idea is safeguarded in explicitly integrating the social acceptance of certain measures into the assessment. The indicators presented are based on the logical combination of statements through the use of Boolean algebra. Starting with basic statements for which the logical value is oriented on the sustainability paradigm, complex multidimensional statements can be constructed and assessed.  

Jan 1, 2009

By Reichman J, Chapman G

The features of seam gas drainage from the point of view of mathematical modelling are outlined and discussed: 1. The use of conventional single phase gas reservoir simulator for very simplified modelling. 2 Alteration of a conventional petroleum reservoir simulator into a specialised simulator for seam gas drainage. 3. Application. of a conventional petroleum reservoir simulator for modelling of seam gas drainage by the way of pseudo-functions and sacrifying one dimension.

Jan 1, 1982

By Leggate J

In the past many coal mining projects commenced without any consideration being given to eventual site rehabilitation. Now that site rehabilitation is assuming greater importance with changing community expectations, and standards are becoming less negotiable, it cannot be ignored in either the development of mine working plans or economic models. The "unspecified" rehabilitation measures associated with many existing projects will be the subject of debate for some time to come yet. It would be wise to plan for the future. Once an agreeed standard of rehabilitation is accepted, good management involves considering practices which will facilitate eventual rehabilitation at least cost. Without planning for rehabilitation, many mines have adopted practices which are likely to result in very expensive rehabilitation measures and impact significantly on the overall profitability of the ventures. With adequate planning, procedures can be developed which achieve the same short term goals without significantly effecting cash flow but with very significant impacts on the final rehabilitation cost. This paper looks at the disposal of tailings and overburden in the coal mining process. The industry has in the past had an obvious preference for the "perceived" cheaper procedures for waste management such as wet disposal of tailings and high dumping of overburden. There are alternatives. The paper discusses the principles which should be incorporated into tailings and overburden disposal systems and identifies viable alternatives.

Jan 1, 1991

The complete life cycle of a production facility has many phases requiring many different skills and many different personalities. It is not unlike the life cycle of a person and many parallels can be drawn from it. I leave some of these analogous situations to your fertile minds. The author, having worked in operations, plant design, plant commissioning, marketing and many other interesting situations through the industry has drawn from this experience and examples given by many associates in the industry.The phases seen are as follows: Concept Studies û someone has a bright idea of how to make a dollar. Scope Studies û what possible processes/options that could make a dollar. Prefeasibility Study û the æviableÆ scope options are studied to develop feasible options. Feasibility study û defines the concepts that should be designed to make a viable project thus enabling financing and project commitment to be made. Detailed Design û an intermediate step that consolidates the inputs to give a robust plant that can be constructed.Construction û people can see what they thought was going to occur and start to understand the plant. Commissioning û the hand-over of æownershipÆ from the conceiverÆs to the operators. Operations û the ætoyÆ has become reality and money must be made. De-commissioning û the plant has seen out the useful life of the ore deposit, it now goes through a further process required by society.Across these phases of plant design run several countervailing management requirements that can influence the outcome of the plant design. Some of the management rigours that have to be applied to the various phases are as follows: costing basis of the various phases; operational and maintenance reviews; sustainable development; risk assessment; reliability reviews; equipment availability; commissioning time; and environmental review.This paper endeavours to awaken people to the phases that projects require for a successful outcome and the management rigour that has to be applied throughout the phases to ensure the correct intellectual horsepower is applied at the right time to ensure the best outcome.Many of you would be parents and realise this is not unlike the development of children, teenagers, adults, retirees and ongoing.

Jan 1, 2002

By B, J Bianchini, N Voermann, C Crowe

Operational and economic imperatives in the metallurgical industry have led to numerous advancements in furnace design. Modern furnaces provide high production rates, high percentage online time, long campaign life between rebuilds and safe operating conditions. Current trends for maximising plant efficiency include increasing the throughput of existing process vessels (often by a factor of two or more) and the use of newer, highly intense processes. In both instances, the process intensity results in the generation of higher heat fluxes to the crucible walls. High-intensity furnace operation with the objectives mentioned above has become possible with the following furnace design features: Strong sidewall cooling systems, using copper coolers, to accommodate the high heat fluxes encountered while protecting the crucible refractories; Robust, spring-loaded furnace horizontal and vertical binding systems which maintain tight brick joints through-out all stages of operation; and Well-designed, intensely cooled tapholes for metal, matte and slag. The integration of these features along with properly selected refractories, appropriate instrumentation systems and efficient water-cooling systems is also highly critical. These design features have been successfully implemented in electric smelting furnaces, flash smelting and converting furnaces (Outokumpu and INCO types) and lance injection furnaces (Mitsubishi, Ausmelt and Isasmelt types). This paper will discuss design aspects and operating results for several installations.

Jan 1, 2002

By S R. Grano, J Duan, T A, D Fornasiero

We have determined the experimental rate constants for chalcopyrite particles floated from a complex sulfide ore and compared them with those calculated using a recently developed flotation model. The model incorporates contributions from the efficiencies of collision, attachment and stability between particles and bubbles, as well as their frequency of collision. For these calculations, the contact angle of the chalcopyrite particles in the ore was obtained independently using a surface spectroscopic approach. The calculated flotation rate constants were in good agreement with the experimental data and able to reproduce the characteristic maximum in flotation rate constant for particles of intermediate size. The values of bubble velocity and turbulent dissipation energy derived from these calculations are relatively low and may well correspond to mean values of these parameters inside the flotation cell. We have extended this approach through the application of a property based model to an operating plant, with a satisfactory outcome.

Jan 1, 2005

The Joint' Venture Method is a procedure for assessing the value of exploration properties, particularly those for which resources have yet to be delineated. It aims to convert the terms of an actual or synthetic joint venture into the equivalence of an arms- lengths cash transaction between a willing seller and a willing buyer. This paper sets out one approach to achieving that conversion. It discusses both simple and complex cases and gives some examples from both public and private documents. It also includes some case studies in which the Joint Venture Method of valuation can be compared with values derived for the same project using other methodologies including actual cash deals. The Method has failings in both mathematics and logic. However because it does reflect or simulate an arms-length deal which takes into account past exploration effort and expenditure and an assessment of prospectivity at a particular point in time, it is felt that it can provide a reasonable approximation of trade value or asset value of a prospect, particularly if used in conjunction with other methods.

Jan 1, 1994

Part of a four-year course in metallurgy, dealing with metallurgical process engineering, was designed for students to acquire knowledge and skill from physical science, metallurgy, process engineering, and social science. Principles of education, and guidelines obtained from a study of professional practice, indicated that students may learn effectively through a planned sequence of problem-solving exercises based on the diverse functions of metallurgists in industry. The more important characteristics of the curriculum and a few illustrations of the problems are included. An outline is given of the current procedures used to develop parts of the curriculum, and of the students' diffic- ulties and achievements.

Jan 1, 1984

This paper carries on from an earlier paper 'Cemented fill practice and research at Mount Isa' and reports further on the laboratory programme at Mount Isa to develop a cheap cem- ented fill using Company waste products. The practical economic significance of availability of cheap cementing agents is re- viewed, with the various alternative approaches available The basic approach adopted within this paper is that use of reactive pozzolans such as ground slags to replace a proportion of the Portland cement in the fill can make mining methods employing cemented fill more economic- ally competitive with other mining methods.

Jan 1, 1973

Railway cuttings require the highest care in design and construction, as the pro- bability of failure concept does not allow any risks to be taken with hundreds of lives being dependent on continued stability. The usual geological influences on stability such as bedding dip and faulting are often discus- sed, but other major problems may come from the presence of sheet joints, cross joints differential weathering and seasonal or daily changes of ground water level. The design of rail cuttings has taken little note of the problems imposed by cons- truction methods, and low cost quarrying methods may seriously weaken a designed shape. The presence of berms and drainage ditches is often difficult to achieve as blasting imposes cumulative stresses and jointing on rocks. Contractors face difficulties in bidding extensive rock cuttings as variations in rock properties are often concealed and overshoot- ing the toe of a batter can easily occur. Modern blasting methods offer some solutions, but the best guide to safe successful cuttings is extensive investigation and the continued involvement of engineering geology at the stages of feasibility, design, construction and maintenance. Two case histories show the influence of folding, faulting and construction methods in the case of slope failure and slope stability.

Jan 1, 1979

By Lunardi P, Pelizza S

The link between the Lecco bypass and major road SS36 (Italy) requires the construction of a double two-way tunnel (through the mount San Martino carbonatic massif). The tunnel excavating section is about 90 sqm through mount San Martino carbonatic rocks. The mountain sides are unstable and are often the scene of large collapsing landslides (tens of thousand cubic metres). The tunnels are very close to the mountain sides. The use of blasting induces vibrations which may reach the Lecco built-up area. With a view to avoiding such dangers the excavating operations were carried out in two successive stages: - opening a pilot tunnel, whose section is about 10 square metres, by a full face TBM to eliminate the more intense vibrations which are generated by the first opening charges; - successive enlargement by blasting.

Jan 1, 1987

In many mining operations, the truck and loader equipment represents the bulk of the invested capital and the majority of the mine operating cost. The profitability of these mines is therefore critically linked to the efficiency of the truck and loader operations. The various factors which affect the productivity of trucks and loaders are analysed by computer simulation, and the results presented in a form allowing assessment of the importance of each factor on overall productivity.

Jan 1, 1983

By P H. Warton

It is proposed to construct a gold extraction plant at Matatoki, near Thanes. Ore to be processed at the mill will come from reopened and enlarged underground mines north of Thanes. The project has been described in some detail in environmental impact reports (Worley Consultants Ltd 1984, 1987), and is now at an advanced stage in terms of obtaining the required statutory approvals.

Jan 1, 1987

Some of the major factors affecting ore reserve estimation in gold mines are discussed together with their impact on computational methods.The major priority in ore reserve estimation is to get sampling and geological problems resolved. Poor basic information cannot be remedied by mathematical methods.Generally the more complex a deposit becomes the greater the need for subjective assessment and the less applicable are more complex ore reserve methodologies.

Jan 1, 1984

There is very little in Australian mining law that sets out the rights of mining tenement and exploration licence holders as against other parties who wish to carry out ground or aerial surveillance over those areas.There have already been several legal actions arising out of this lack, and more can be expected as the public places more rigorous constraints on corporate and individual behaviour. Field personnel, who are mainly fairly junior and less experienced, are entitled to some guidance from the minerals industry, guidance which up to now appears to have been either lacking or covering such a wide range of standards from corporation to corporation as to be virtually useless.Because each State writes its own laws there is no consistency, and the laws generally are lagging behind developments in the industry. In particular, the practice of granting mining tenements for sporadic exploration, a practice that is a leftover from much earlier mining law, has dotted the Australian continent with unattended and unmarked or poorly marked tenements that are difficult to find but confer on the holder prior rights to the minerals under them. Entry onto those areas in most jurisdictions is an offence and their existence compromises the efforts of regional explorers.This clearly unsatisfactory situation requires remedying, which is the purpose of these proposals. A more systematic approach to the granting of reconnaissance, regional and detailed exploration, mining, and retention rights will eliminate much of the problem. For the rest, a code of practice needs to be adopted as soon as possible.

Jan 1, 1996