Search Documents

By Joseph Cervik

Gas occurs in coalbeds in an adsorbed and a free gas state, Adsorbed gas is stored in the micropore structure and its transport is governed by Fick's law. The free gas occurs in the. fracture system and flows according to Darcy's law. These two modes of mass transport are interdependent. Production decline curves of coal-gas wells are of the constant percentage decline type and, thus, show no indications of flow characteristics peculiar to coal-gas reservoirs. The effectiveness of surface boreholes as a degasification scheme depends upon both good fracture permeability and a high fracture density. Conventional methods of reservoir engineering analysis are not applicable to coalbeds.

Jan 1, 1969

By F. P. Dewey

THE Falling Cliff Mine adjoins on the west the Bertha Mine, from which a large amount of first-class ore has been taken, producing the purest zinc known to commerce. The two mines are in the same hill, Bertha being on the northern 'slope and Falling Cliff on the top and opposite slope. The formation is No. 2 limestone. Although considerable exploration has been done by numerous shafts and' tunnels (there being over six hundred feet of the latter), no satisfactory determination of the dip and strike of the .vein could be made on account of its contortions, the ore descending from the top to the. bottom of the tunnels and rising again in very short distances; but enough has been done to indicate a very large mass of

Jan 1, 1882

THE irregularity of the Mount Morgan ore body presents problems other than those for mining only. For irregularity of outline is coupled with irregularity of grade, and the ore varies so rapidly from profitable to non-profitable, and from highly siliceous to highly pyritic, that the task of estimating quantities and values of ore reserves is manifestly rendered a difficult one, while the actual disposal Of the broken ore demands constant supervision.Four classes of ore are handled. The oxidized ore, cheaply mined and cheaply treated, is obtained by quarrying from the top of the mountain. Below the 315-ft. mine level (measured from the original summit) sulphide ore comes in, and this is divided into siliceous sulphide ore (too siliceous for economic smelting), sulphide ore suitable for smelting, and ore too poor either to be smelted or to be treated by wet process with the siliceous ore. It is with these three latter descriptions of ore that this paper principally deals.Although the output from most stopes in the mine may usually be presumed beforehand to be either smelting or wet-treatment ore...

Jan 1, 1910

By Lyda W. Hersloff

An environmental monitoring program was established to assess the baseline of parameters which may be impacted by a research and development hydraulic borehole mining operation. During the baseline program, two aquifers were identified at the borehole site with the overlying sand aquifer being distinct from the ore sand aquifer on the basis of radiological parameters. The direction of flow of groundwater was determined to be north 19° west at a rate of 1.82 feet per year. Tests to determine the effect of backfilling the boreholes indicated that using overburden from the open pit mining operation would not significantly increase the radiological consti¬tuents of the ore sand aquifer. Mining measurements of the- radon flux from the borehole indicated that the actual release rate of 0.035 pCi/sec was several orders of magnitude less than the calculated estimate by the Environmental Protection Agency. Finally, a gamma survey conducted at the site indicated that the terrestrial component of background radiation was consistent with that in areas near uranium deposits. The methodology used as well as the supporting data are given in this report.

Jan 1, 1981

By W. L. Dalmijn, J. M. Versteegen

During the production of silicon carbide, a byproduct is generated that contains a mixture of crystalline and amorphous silicon carbide. Utilizing the difference in density, shape, and surface properties of the crystalline and amorphous silicon carbide, separation tests were carried out with gravity concentration. The processing of the coarse fraction of the silicon carbide mixture by jigs resulted in a high grade crystalline SiC concentrate with the desired specifications. The separation was largely influenced by the shape factor. A jig with a newly designed hydraulic drive was used to carry out the test program.

Jan 1, 1991

By R. C. Moe

Pelletizing studies were conducted to find ways of improving the metallurgical properties of acid and fluxed pellets. In acid pellets, melting temperature was controlled by the formation of low melting temperature fayalite during reduction. Formation of a permeable metallic shell during reduction allows diffusion of reducing gas to the pellet core, decreasing fayalite formation. With fluxed pellets, slag chemistry had the main influence on metallurgical properties. Mineralogical, chemical and structural transformations that occur during reduction were studied at various intervals for a number of Mesabi Range pellet types. Six pellet types were selected for further investigation based on significant differences in softening/melting characteristics. Retention of porosity in the metallic shell was found to be the overriding factor in determining softening/melting behavior.

Jan 1, 1990

By R. A. Alock

The character, occurrence and genesis of the three types of nickel deposits, sulfide, laterite and deep-sea nodule are described, highlighting the differences in mineralogy and chemical composition that effect the extractive metallurgy of nickel and associated byproducts. World nickel production and current resources by deposit type and geographic location are also reviewed.

Jan 1, 1988

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By R. Wharton, M. Bagley

Following a series of papers relating to the certification of explosives for sale in member states of the European Union presented at previous ISEE conferences, this poster paper has been prepared to stimulate discussion and debate on the recently published European Directive on Pyrotechnic Articles.

Jan 1, 2008

What is the best circuit to comminute primary crusher product to make beneficiation feed? Finding the best circuit to crush and grind minerals to beneficiation sizes is a complex problem that can lead to interminable discussion. Conclusions reached can be questioned. This will continue as long as the technology of comminution continues to expand, and is a mixture of many technical and economic factors in what is not a precise science. Laboratory and pilot plant procedures now exist that can help process engineers make sound decisions on which circuits are the best for crushing and grinding the specific ore being studied. It is the aim of this paper to discuss such procedures so a better under- standing of key decision parameters is avail- able, and to update comminution testing which has seen a. period of change in which new procedures have been introduced.

Jan 1, 1978

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

By C Paoletti

About 15 years ago the debate on the reliability of sampling procedures for agricultural food and feed commodities was initiated by a few brave scientists who questioned the representativeness of what, at the time, were routine sampling procedures established exclusively on the basis of tradition and practical feasibility. Over time several national and international organisations contributed to the discussion, developing standards and publishing papers either to underline the fact that sampling is always a source of error, in itself, which cannot be overlooked, or to minimise the relevance of sampling on the basis of argumentations linked to time and money limitations. The latter dominated, but is nevertheless impossible to accept from both a scientific and a responsible management perspective. Here the author presents an historical overview of these past 15 years, illustrating the most controversial issues, reporting major achievements in food/feed sampling, highlighting milestones, as well as unresolved problems that still need the attention and contribution from the sampling community. The need to incorporate Theory of Sampling (TOS) into food/feed safety assessment (pre-market), as well as into food/feed safety monitoring (post-market) has recently been highlighted, and the practical applicability of TOS to base food/feed safety decisions on representative sampling, has been explored and documented via concrete examples of risk analysis in different areas of food/feed industrial production chains. Now it is time to move forward and ensure that TOS is fully integrated into the well-established Food and Agriculture Organization (FAO) / World Health Organization (WHO) risk assessment approach, in order to guarantee a transparent and correct universal frame for risk assessment and the subsequent management decision-making process. WCSB8 offers the ideal platform to explore the best way to do so, switching from a theoretical discussion of correct sampling principles for food and feed agricultural commodities to practical recommendations in the interest of consumers, worldwide. These 15 years have also been a personal journey of interesting dimensions, indeed a veritable roller-coaster ride in-and-out of the scientific, technological, industrial and (last but not least) regulatory worlds. The start was WCSB2 in 2004, when I flew to Australia to discover if in other areas sampling had been identified as an unavoidable issue and, if so, what the solution was. There, I found a good travel companion who today is still on my side, to assemble the puzzle and explore how to shape the future, to concretely answer to the 15 years’ quest for proper sampling in the assessment and monitoring of food/feed safety.CITATION:Paoletti, C, 2017. Assessing and monitoring food and feed safety – a 15 year quest for proper sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 39–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Yoshihiro Kawarabata

INTRODUCTION With only about 30% of Japan's entire population served by sewer systems at the end of 1980, extensive sewerage construction programs have been implemented. As major sewer networks in large cities are near completion, construction of smaller sewer networks in less populated areas and branch sewers in urban areas is on the rise, where a demand for sewer tunnels of 600mm to 1500mm diameter is very heavy. The pipe jacking technique, usually employed to excavate such small diameter tunnels, therefore has become the subject of further technological development and sophistication to cope with the increasing volume of construction. At the 1979 RETC, the state of the art on the slurry shield tunneling method at that time was reported. This paper is a follow up to the last paper and discusses a newly developed boulder crushing equipment and automatic pipe jacking system for the slurry shield method and their application. Such technological advancement as high-degree mechanization and automation will significantly improve tunneling operations in response to the aging society to come. Through application of the technique on so called factory automation, this is a step towards field automation for the construction industry.

Jan 1, 1983

By V. Pasupathi, R. E. Hummel, J. W. Koger

Specimens of P1 brass were plastically deformed at room temperature to various degrees of deformation and subsequently cooled in order to transform them to low-temperature martensite. Deformation shifts Ms. A, , and the temperature of minimum resistivity to lower temperatures, and also decreases the temperature coefficient of electrical resistivity. These properties change rapidly up to about 15 pct reduction but vary very little with higher deformation. The possible relationships between martensite formed by deformation and the M, temperature of low-temperature martensite are discussed. Evidence is given that deformation martensite delays the formation of low-temperature martensite. BETA' brass undergoes at least two different types of martensitic transformations. One of these transformations (B1- B2) was first observed by Kaminski and ~urdjumov' and occurs when 81 brass with a zinc content between 38 and 42 wt pct (quenched from the single-phase region) is cooled below room temperature. Jollev and Hull' determined the structure of 0" from X-ray and electron-diffraction data as ortho-rhombic. Kunze came to the conclusion that the super-lattice cell of 0" is one-sided face-centered triclinic (pseudomonoclinic). The second martensitic transformation (B1-A1) occurs when the specimens are deformed at or somewhat above room temperature. This type of martensite will be called deformation martensite. Horn-bogen, Segmuller, and Wassermann4 determined the structure of deformation martensite to be bct. (An intermediate phase, az, occurs before the final phase appears.) At deformations higher than 70 pct, a, transforms into a.4 A critical temperature Md exists above which no transformation occurs during deformation and is estimated to be around 400°C in P1 brass.5 This martensite has elastic properties.6 When the sample is stressed, martensitic plates appear; when the stress is released, the plates disappear. The present paper studies the effect of deformation martensite on the formation of low-temperature martensite. The experiments involved samples of 8, brass which were plastically deformed by various amounts and were subsequently cooled below the transformation temperature. EXPERIMENTAL PROCEDURE The 13 brass investigated was made from 99.999 pct pure copper and 99.9999 pct pure zinc and contained 38.8 wt pct Zn. The specimens, consisting of foils 0.1 mm in thickness, were heat-treated at 8'70°C for 15 min in an argon atmosphere and then quenched into ice water. They were then deformed by cold rolling and subsequently cooled at a rate of 1°C per min. The martensitic transformation that occurred during cooling was followed by electrical resistivity measurements. The resistance measurement technique and its accuracy have been described in a previous paper. Because the transformation 81 —-8" occurs below room temperature, the samples were placed in a cryo-stat which contained isopentane as a cooling medium. The isopentane was cooled by liquid nitrogen pumped under pressure through a 15-ft coil of copper tubing which was immersed in the isopentane. The nitrogen flow was regulated by a temperature controller using two thermistors in the cooling medium. The cryogenic liquid could be heated with an immersion heater. The useful temperature range with this device was from +25° to approximately -155~C. EXPERIMENTAL RESULTS Resistivity Measurements. The following abbreviations are used in this paper to label the characteristic temperatures during the martensitic transformation. M, is the starting point of the martensitic transformation and is defined as that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line. Mf is the temperature at which the martensitic transformation is completed. On reheating, the transformation from martensite to the parent phase starts at a temperature A, and ceases at a temperature Af. Fig. 1 presents five different resistivity vs temperature curves corresponding to the transformation of brass from Dl to 8" after different degrees of reduction in thickness. The following observations can be made from these curves. 1) With increasing degree of deformation the Ms temperature is shifted to lower temperatures. This shift ranges up to 35°C compared to the undeformed state. This is also indicated in Fig. 2, where AM, (the shift of Ms, compared to the undeformed state) is plotted vs the degree of deformation. AM, increases rapidly until a reduction of about 15 pct is reached. With higher deformations, no additional increase in AM, was found. 2) With increasing degree of deformation the temperature of minimum resistivity (M) is also shifted to lower temperatures. The shift, attains a maximum of about 61°C compared to the undeformed state. In Fig. 3, AM is plotted as a function of deformation. It can be seen that, as in 1 above, AM increases rapidly and no further shift of M occurs for deformations greater than 15 pct. 3) The temperature coefficient of resistivity, is given by the slopes (dp/dT) of the linear portions of

Jan 1, 1969

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By Christopher J. Bise

INTRODUCTION Before a mine is planned in detail, a preliminary analysis is often conducted. This preplanning permits the mining engineer to make a rapid assessment as to whether or not a particular mining property warrants further consideration. In fact, a properly conducted preplanning phase can come within 10% to 20% of the actual results, thereby saving the mining engineer valuable time before committing himself to a fine-tuned analysis. The questions to be answered by mine preplanning are (1) What will be the operating conditions for the mine? and (2) How long will it take to complete the project? To answer these questions, calculations dealing with reserve estimation, production planning, man- power planning, and project scheduling are conducted. The following sections discuss these various phases of mine preplanning in greater detail. RESERVE ESTIMATION The estimation of the various characteristics of a reserve, such as quantity, grade, and thickness, is an ongoing process throughout the life of a mining venture. However, the reserve-estimation phase of mine planning is more closely associated with the preplanning phase. There are many different techniques employed in reserve estimation of solid mineral deposits; variations among them are introduced because of such considerations as ease of application or level of accuracy. In any event, each technique is developed in the following manner: (1) the mineral body is represented pictorially and then subdivided into blocks related to one or more samples of exploration data, (2) the area and volume of each block is determined, (3) the volumes are converted to representative tonnages (or, for example, grades), and (4) the results are tabulated. To illustrate this procedure, the polygonal (area-of- influence) technique will be presented due to its ease of application, flexibility in dealing with different deposits, and general acceptance. The polygonal method assumes that all characteristics of a mineral body extend halfway between a point of observation and any other point of observation. The explored portion of the mineral body is represented by polygonal prisms whose depths relate to the characteristic in question (grade, thickness, etc.) and whose plane bases relate to the area of influence of each point of observation (drill hole, etc.) as shown in Fig. 1. The polygons must be constructed in a definite order, usually clockwise and from the periphery to the center of the deposit. Table 1 can then be used to calculate the characteristics in question. Since, by definition, the polygonal method assumes that the characteristics of a mineral body extend half- way between points of observation, it becomes readily apparent that the evaluation of a vertical-drill hole exploration program requires that the sides of the polygons be formed by the intersection of perpendicular bisectors (Fig. 2). Figs. 3 and 4 show correct and incorrect construction of the polygons. The criterion for correct construction of the polygons is that all points within a particular polygon must be closer to its rallying point than those located in any other polygon. This is clearly not the case for certain points that are located in the polygon containing rallying point B in Fig. 4. Although this method can be used where the drill holes are irregularly spaced, calculations become less tedious when a square net (Fig. 5) or a chessboard (Fig. 6) grid is adopted. The numbers shown in Figs. 5 and 6 represent the relative weight for each of the shaded areas. In general, the greater the number of polygons, the more continuous the mineral body, and the more regular the grid, then the more accurate the computations will be. PRODUCTION PLANNING Before an acceptable evaluation of the production potential of a mine can be determined, a thorough exploration program should be conducted. It seems obvious that the nature and properties of the deposit and adjacent strata, the presence of impurities, and other mining conditions should be adequately determined prior to production planning and equipment selection. The lack of sufficiently detailed knowledge of the many mining parameters has led to the failure of numerous operations. For example, targeted production tonnages and equipment sizes for a coal mine are intimately related to the seam thickness. Needless to say the quality of information that is gathered from an exploration program can have a tremendous impact on the production plan. Production plans are developed initially by determining reasonable shift tonnages per operating section. Most of the time these values are developed from his-

Jan 1, 1986

By T. A. Rickard

Our Transactions contain two notable papers descriptive of the stamp-milling practice of the Black Hills and of Grass Valley, namely, the elaborate and complete treatise of Prof. H. 0. Hofman, on " Gold-Milling in the Black Hills,"" and the paper describing the North Star mill, by E. R. Abadie, its superintendent. Having visited and examined the stampmills of both localities, I venture to offer here such comment as more recent information or a different point of view has suggested.†

Jan 1, 1896

By G. C. Lindeque

"A downward trend in tyre life on haul trucks at an open pit iron ore mine prompted an investigation into the current tyre management strategy in order to improve tyre life. ‘Best practice’ was compared to the current tyre management strategy at the mine to determine aspects that could be improved. Aspects that showed significant room for improvement included employee tyre awareness, tyre pressure maintenance, and road conditions. For each of these aspects a plausible alternative was suggested.A new tyre management strategy was formulated as a step-by-step guide on how to implement the proposed changes. Each step introduces new initiatives but at the same time builds on the previous step’s success. A sensitivity analyses was performed to determine the impact of the proposed changes, with the variables being the reduction in the percentage of premature tyre failure, and the reduction of the site wear rate.The ‘most likely’ scenario showed an increase in tyre life of 41% for the Komatsu 730 trucks and 105% for the CAT 777 trucks if the entire tyre management model is implemented. This would result in a possible annual saving related to tyre usage of R9.2 million. OverviewThe study focused on the tyre life on the main haul fleet at an open pit iron ore mine. The haul fleet consisted of 17 Komatsu 730 (180 t) haul trucks and 12 CAT 777 (90 t) haul trucks.The haulage operation consists entirely of tyre-based haul trucks. Five per cent of the total mining budget is related to tyre costs. Since 2012 there has been a steady decrease in tyre life as measured in operating hours (Figure 1) due to the high percentage of tyres that fail prematurely. In 2014 a total of 41% of all tyres failed prematurely and 61% were classified as ‘worn out’."

Jan 1, 2016

By W. J. Bennett

WHEN Dr. Horace Fraser, your President, invited me to speak to you today I advised him in confidence that I was leaving my present positions on April 30th. In the circumstances it seemed to me that this audience might prefer to have as its speaker one who wo.uld J1ave a continuing association with the atomic energy programme. Dr. Fraser was kind enough to suggest that my re-marks might he of special interest to you, since I would be able to sum up my views on the atomic energy programme. I hope that I will not disappoint him or you on that score. I am particularly pleased that my last public appearance in my present positions should be at the Annual Convention of the C.I.M. since, as all of you know, a very important part of my work has been in the mining field. As it happens, my first public address on the subject of atomic energy and its raw material -uranium -was made at your Annual Convention in Montreal in April, 1949. It seems fitting that my final address should also be made at this convention -nine years later.

Jan 1, 1958

W. ROWLAND Cox,* New York, N. Y. (written discussion?).-The process described by Mr. Malcolmson undoubtedly represents a great stride toward conservation of our natural resources. Without discussing the subject from an economic standpoint, I wish further to emphasize the fundamental principles of the Smith process in order that its economic value may be fully appreciated. The process is essentially a means of producing an ideal fuel, as regards its combustion qualities, by the removal of the so-called volatile matter from the coal, in the form of byproducts, which have value for other purposes far in excess of their fuel value. In other words, coals which contain. large amounts of gas, tar, and ammonia, and are not suitable for domestic or industrial fuel, or for treatment in byproduct coke ovens or gas retorts; because they possess poor coking qualities, can he prepared for commercial use by the. Smith process with a very high degree of efficiency. Much work has been done along this line, both in this country and in Europe, in developing a means of preparing coal, as the economic advantages have long been recognized. To the best of my knowledge, the Smith process is the only one that has proved its commercial adaptability. Distillation of coal at 900° to 1000° F. (480° to 540° C.) yields a large amount of tar and oils. The residue of the distillation, however, is a very friable semi-coke, wholly unsuitable for use as a fuel, unless it can be charged directly into a byproduct gas producer. The problem which confronted the inventor was then to convert this carbon residue into a commercial product, and it is in this step that the Smith process has overcome the obstacles which prevented a number of other methods from becoming commercially practicable.

Jan 10, 1918