Search Documents

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By Angus M. Henderson, Charles R. Lilley

Underground mining at Kanowna Belle commenced in July 1998, using a sublevel open stoping method. The use of this stoping method necessitated the use of a cemented fill material for filling primary and secondary stope voids. A detailed engineering study recommended the construction of a cemented aggregate fill (CAF) system for Block A, in favour of paste fill. The CAF system consisted of a crushing and screening plant, a surface binder preparation plant and an underground fill station. Conventional underground dump trucks were used for CAF delivery. Since CAF plant commissioning in March 1999, 1.2 million tonnes of CAF have been placed underground. CAF segregation was the most significant quality control issue during CAF system operation. At the hangingwalls of filled stopes, CAF segregation sometimes occurred to such the extent that the resulting fill material was essentially uncemented coarse aggregate. This caused some CAF dilution during the extraction of adjacent secondary stopes. Numerous CAF were prepared on site for strength testing. A relationship has been formulated that allows estimation of the CAF uniaxial compressive strength in MPa, based on the cement content (c) and porosity (n), as follows. [ ] Practice at Kanowna Belle has confirmed that laboratory testing results cannot be applied for optimising the mix design of cemented rock fills that do not exhibit debris flow behaviour during placement. The grain flow characteristics and consequent marked segregation dominate the in situ fill strength. A detailed review of backfill requirements for the lower mine indicated that the total net present cost of CAF and paste systems was similar. Several significant operational advantages offered by a paste system have resulted in its selection for the remaining mine life. The construction of a paste fill system at Kanowna Belle is currently in progress.

Jan 1, 2001

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. As part of the mining process, Coteau removes and replaces thin layers of suitable plant growth material (SPGM) generally ranging in thickness between one and five feet. Historically, tractor-scrapers completed this work; however, rising tractor-scraper costs and increasing haulage distances sent Coteau in search of a lower cost method resulting in the acquisition of a backhoe/truck fleet in 1995.

Jan 1, 1997

By V. Price

Abstract: Action of certain strains of bacteria has been implicated as a significant factor in the oxidation of ore deposits. Other bacteria are thought to be significant in the formation of syngenetic sedimentary ores and in supergene enrichment processes. A normal soil/ground-water regime provides all of the necessary pH and Eh conditions for several groups of bacteria which influence the sulfur cycle in nature. Limiting concentrations of nutrients such as sulfate ions can determine whether a particular microbial species is active at a given place. In the present study, ground water was analyzed from a mineralized area and from a presumed barren area. Trace metal content of the ground water gave no well defined clue as to the presence of a sulfide ore deposit. Sulfide producing bacteria (presumably sulfate users) were found in water from about 50% of wells sampled in the mineralized area and in about 30% of samples from the barren area. These bacteria are readily detected and may provide a useful tool for regional geochemical recon-naissance. Bacterially produced sulfide ions can remove metals such as copper and zinc from solution thus complicating the interpretation of hydrogeochemical prospecting.

Jan 1, 1972

By A. Gupta, S. C. Srivastava, K. K. Saroj

Bacterial degasification of methane and conventional methane drainage for generation of power have become accepted practice. Comparative economies of both the techniques have been described. Authors have discussed an alternative technique, involving complete methane biocycle. The first stage of the entire process involves gasification of coal using a consortia of bacteria to generate methane. The generated methane has been proposed to be pumped,as in conventional methane drainage. Technique described is basically similar to underground coal gasification, with the difference that in place of coal combustion, degradation of coal to lower molecular weight compounds by one set of bacteria and then methanogenesis by methanogens, producing methane have been described. Brief account of communities of bacteria that may be employed have been dealt with. Three arguments in favour of proposed technology as an alternative to conventional coal mining are: 1.Total elimination of hazardous operation. 2.Availability of power plants based on methane drainage, assuring comparative economies. 3.Possibility of utilisation of fuel cell technology for power generation giving higher efficiency. All the three phases of complete blocycle viz (1) methane generation from coal (ii) conversion of methane to hydrogen and oxygen (iii) conversion of products so obtained to methane, thereby completing the cycle have been discussed. INTRODUCTION Drainage of methane by conventional pumping process (Boxho,et.al.,1980) not only is helpful in maintaining safe extraction of coal, but with utilisation of extracted gas for power generation, also helps in over all economy of coal mining. This is gradually becoming standard practice for mining of coal in highly gassy mines. An alternative technique (Thakur et. al., 1991) of bacterial degasification of coal seams is also gradually gaining ground. The bye products of this process that is carbondioxide and water, do not contribute towards economy of coal extraction process. However the technique has its own advantage particularly in goaf area for avoiding fire hazard and drainage of methane from coal seams prior to initiation of mining operation. Either of these techniques could be applied in specific situations with success.

Jan 1, 1993

By R. A. MacGregor

The Stanreck mine of Stanreck Uranium Mines Limited in located on Quirks Lake in the Elliot lake - Blind River area of Northern Ontario. It is approximately 25 miles north of the north shore of Lake Huron, equidistant between the cities of Sudbury and Sault Ste. Marie. The property was developed ad brought into production at a rate of 3,000 tens of ore/day during the uranium boom of the mid 1950's. By 1960 mine waters were becoming quite acid through the activity of bacteria. Treatment of this water was begun for pollution control and a small amount of uranium which had been leached from the ore by these acid waters was recovered. Development of bacterial leaching with a view to increasing production by this method commenced in December 1962. Subsequently, it was succeesfull in producing 10,000 - 15,000 lbs. of U308/month. Since late 1964 uranium production has been obtained solely from bacterial leaching. A rare earth concentrate was also made for its yttrium content during 1966 and 1967. This paper describes the development, operation and methods used in the underground bacterial leaching process.

Jan 1, 1969

By Wolfgang Sand, Alex Schippers, Tilman Gehrke, Thore Rohwerder, Peter-Georg Jozsa

Metal sulfides are degraded via thiosulfate (pyrite) or via polysulfides and sulfur (sphalerite, galena, chalcopyrite) by leaching bacteria The attack on the crystal lattice is either effected by only iron(III) ions or by iron(III) ions and protons, respectively. Consequently, different endproducts are formed. For a control of ARD-processes, these reactions need to be hown to regulate them. Experiments in percolators up to 65 m3 with inorganic compounds like fluoride, concrete, or SDS resulted in differently lasting inhibition. Microcalorimetric measurements of microbial leach activity allow monitoring of these effects with respect to active bacterial cells, and, in addition, the amount or rate of dissolved metal sulfide allowing prediction of possible endangerment by ARD.

Jan 1, 2000

By M. Stefanakis, A. Kontopoulpus, K. Adam

The application of Bacterial Oxidation as a pretreatment step for the extraction of gold from the Olympias refractory pyrite concentrate is described. A wide review of Bio-oxidation is presented focusing on the current process developments and commercial applications relevant to the treatment of gold bearing sulphide ores and concentrates. Preliminary batch and semi- continuous tests on the Olympas concentrate indicated that with Bacterial Oxidation quantitative gold liberation may be achieved. fie effect of such parameters as pH, Eh, temperature, particle size, operating pulp density and retention time on the extent of sulphur oxidation and subsequent gold extraction by conventional cyanidation are also examined. Finally, a preliminary evaluation of Bacterial Oxidation as a potential process alternative for the treatment of the Olympias concentrate is presented.

Jan 1, 1989

By Ü. Atalay, G. Alaeddinoglu, G. Özcengiz, G. Özbayoglu, Z. Özdemir

In this study, bacterial pre-treatment was applied before cyanidation in order to enhance the solubilization of silver from Artvin-Kafkasör ore Direct cyanidation process was found inefficient to recover silver from the ore. Only 40.36% silver recovery was obtained with direct cyanidation while silver recoveries of above 60% were obtained after bacterial treatment. Thiobacillus ferrooxidans was used as the microorganism in pretreatment tests. Effects of various parameters such as pulp density, duration, inoculum size and particle size on silver recovery have been investigated in this study.

Jan 1, 2001

By J. R. Parga

In mineral processing, poor froth-flotation performance translates into both an enormous loss of revenue and an unnecessary waste of the ore reserve. In this context, Bacís Mining Company developed a versatile new, high-performance flotation-cell design that can be incorporated into various flotation circuits. The main feature of this circular cell is that it is comprised of two separate sections, namely, a flotation cell that uses wash water to minimize the entrainment of fine gangue particles into the froth product and an external bubble generator that produces small bubbles of relatively uniform size at a specified aeration-rate. The air/water mixture is blended with the pulp by gentle agitation, so as to enhance particle-bubble aggregate-stability. Comparative metallurgical performance with conventional flotation cells show that the power requirements and operating costs for precious metal flotation are three times lower, while the concentrate grade is 7% higher and the recoveries of precious metals are 5% higher.

Jan 1, 2009

By Ralf Plinninger, Pafos Busch, Richard Gradnik

This paper presents the details of the Bad Bergzabern tunnel project. This tunnel is the main part of the B427 federal road bypass, intended to improve the regional traffic infrastructure and to reduce the traffic load in the historic city centre of the health resort Bad Bergzabern. Located in the south-western part of Germany, the project area is situated at the eastern margin of the so-called Palatinate Forest, a low mountain region of mainly triassic sediments with a complex and variable geological history. The German federal government, represented by the office of mobility of Rhineland- Palatinate, awarded the contract to BeMo Tunnelling, a specialized Tunnelling company with a long history of innovation and success in NATM tunnelling. The contract includes the construction of two separate tubes with a length of approximately 1,44 km (0.9 mi)—the road (main) tunnel with a cross section of 101 m2 (1,090 sq ft) and a parallel rescue tunnel with a cross section of ca. 23 m2 (250 sq ft.) Both are connected by six cross passages. Tunnels and cross passages are excavated according to the principles of the New Austrian Tunnelling Method (NATM). Due to BeMo Tunnelling’s technical expertise and capabilities, the project team was able to engineer a speed-up concept that saves money and time for the construction team and client. This paper presents the innovative approach BeMo Tunnelling made to optimize the execution of the tunnelling works and the challenges the project team is facing with regard to a complicated geological situation, countermeasures against an increasing effect of climate change and volatile prices for construction materials.

Jun 13, 2023

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

By S. K. Kawatra

It is common in coal-cleaning operations to produce a fine waste stream which contains a considerable amount of coal, but which is not economical to recover both because it is mixed with large amounts of difficult-to-remove clay slimes, and because the fines are often heavily oxidized. Conventional froth flotation machines cannot produce an acceptable product from such material in a single stage of flotation, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and was installed and tested in a coal-cleaning plant in Ohio. The feed coal contained 39.8% ash as fine clay, and 2.83% total sulfur, and was 80% passing 176 micrometers. The coal was a thickener product which had oxidized for some time, and was very difficult to float. However, using the new column it was possible to recover up to 85% of the calorific value in a product containing less than 11% ash, and up to 60% of the calorific value in a product of less that 8% ash. The bulk of the pyritic sulfur was rejected from the coal as well. Multistage flotation tests showed that the flotation column was able, in a single stage, to produce the best froth flotation product that it was possible to recover from this coal.

Jan 1, 1994

By Peter Amelunxen, Craig Lockhart

Significant effort was made in 2003 and 2004 to upgrade the existing instrumentation and process control infrastructure at the Phelps Dodge Bagdad copper concentrator. Specifically, • cameras were installed on the feed belt for online image analysis data, • ultrasonic level sensors were installed for froth height and sump level control, • a trial froth image system was installed on one of the rougher rows, and • a new expert system to tie everything together was integrated and tuned in-house. Control philosophy, observations, opinions, and general tips and tricks are discussed with the hope of assisting other plant personnel and expert system integrators.

Jan 1, 2005

By Edmund C. Bitzer

The unit costs of dry crushing, within the efficient reduction ranges of equipment now available, are considerably less than those for the reduction of the same material in the same size range by wet mills using grinding media. This is a commonly recognized fact which cannot be disputed; still we find considerable imbalance in costs between the crushing and grinding sections of many operating mills. In other words, there are many instances where more reduction could be accomplished in the lower cost area of dry crushing. In addition, equipment is now available which enlarges this area and makes it possible to consider much finer crushing than has been heretofore economically feasible. There has been a tendency for the past two decades to utilize wet rod-¬milling in the reduction step. This actually amounts to a fourth stage of crushing in a size range formerly served by roll crushers which have fallen from favor on account of high operating costs, Some investigations have indicated that there is not sufficient difference in the operating costs of rolls and rod-mills to give a clear cut advantage to either method, There has for some time been a need and an opportunity for a dry crushing process to improve costs in the range now served by these two systems.

Jan 1, 1965

By S. Chander

A mineral or metallurgical process uses various inputs, such as ores, energy and other raw materials, to make different products that fulfill societal needs. The processing of raw materials has changed in recent years due to the increased complexity of processing low-grade ores, intensifying competitiveness and greater constraints. For process improvement, various plant optimization and process modifications must be conducted under environmental, social, political and economic constraints. Processing research and education&apos;s success in meeting the process industry&apos;s future needs depends on an adequate balance between micro- and macro-engineering approaches. In its simplest form, macro-engineering is concerned with the "big picture," while micro-engineering requires looking at a subset of the process. So macro-engineering may be defined as an investigation of the larger or "whole" system to achieve the desired goals. And micro-engineering may be viewed as a quantitative investigation of a subset of the process, to determine cause-and-effect relationships within the subset. Two different approaches might be used in macro-engineering analysis. In one, the big picture may be viewed without a detailed knowledge of the subunits. With this approach, statistical tools are used to relate input and output parameters. Also, actual plant data or analog models might be used to obtain the desired information. The usefulness of such an approach increases with problem complexity. To attain the desired goals using the second, "model-based," approach, a detailed knowledge of the subunits is often useful and their interactions may be considered. In complex process analysis, the first of these approaches is more useful since less information is needed. However, it is also less exact and more likely to fail if there are significant changes in conditions and interactions. The second approach, on the other hand, is more exact, with greater predictive ability within the narrow subset being considered. Consequently, it is difficult and costly to conduct.

Jan 1, 1992

One of the core tenets of Sustainable Development is transparency and information sharing, i.e., government and corporate reporting. Governments report on issues within their sphere of responsibility to the degree that their constituents demand that they do so. Firms undertake reporting for two reasons: they are required to do so by law, and doing so makes good business sense. In recent years, stakeholders have come to see themselves as having a right to information about government actions and business operations that have the potential to affect their lives, health, community and environment. As a result, disparate groups, including industry associations, non-profit groups, academics, and individual firms, attempted to lay out what governments and firms should report. There are many types of sustainability reporting. In this paper we focus on three of them that both governments and firms utilize. We discuss the benefits of each. We argue that while the goal of complete and perfect data is not achievable or feasible, sustainability reporting of all three types is necessary to ensure that sound public and private decisions are made.

Jan 1, 2007

By Frank W. Reinrniller

Mill ball charging systems have undergone little change during the past two decades. Most operations utilize a locomotive/ball car combination to load and haul charges from the ball storage bin to the mill charging boxes or, alternatively, transport charges to the charging boxes by means of a ball bucket handled by bridge crane. This paper describes a new concept in ball handling systems that is in operation at the Island Copper Concentrator of Utah Mines, Ltd. at Port Hardy, B.C. This system employs a narrow belt conveyor to convey a weighed charge to each of nine belt unloading stations at the mills. In operation, the system has proved to be practicable, trouble-free and economical of operating labor.

Jan 1, 1977

By Tom F. Deems

The term ball clay is applied to plastic sedimentary clays that have a high content of kaolinite and that possess white firing properties and high green strength (Mitchell and Stentiford, 1973). However, the name ball clay is not derived from any specific property of the clay. Instead, it comes from the original method of production in southwestern England (Scott, 1929). From open pits, the clay was cut into cubes with hand tools. The sides of the cubes were about 220 to 250 mm (9 to 10 in.) and weighed 14 to 16 kg (30 to 35 lb.). The eventual rounding of the corners with handling before sale gave rise to the term ball clay. Ball clays provide the workability and green strength required by the whiteware section of the world&apos;s ceramic industry. The main applications are in the sanitaryware, tile and tableware sectors. Each, though, requires particular technical properties in the ball clay component. The clay has to be as white firing as possible for all applications. However, for sanitary-ware, the rheological properties are most important. For tableware, fired whiteness and freedom from specking are the main criteria. Tiles need a reasonable green strength but the clay also needs to be cost-effective. The technical properties of the individual clays in any deposit depend on the clay mineral assemblage. This, in turn, depends on the geological formation of the deposits. Hence, it is the latter that largely determines the market sector for which the clay blends from a particular deposit are suited. Formation of ball clays Ball clays are formed from three main components - kaolinite, micaceous minerals and quartz - while carbonaceous material is also often present. The crystallinity of the kaolinite and mica varies. There are also occasional minor occurrences of feldspar, chlorite, montmorillonite andmixed. layer minerals. Marcasite, siderite and anatase also occur in small amounts. The properties of the clay depend on its mineralogical composition and its particle size distribution, particularly in the lowest size ranges. The original source rocks and the environment of deposition of the clay are the controlling factors. The importance of weathering processes in the formation of ball clays has long been recognized (Bristow, 1968). The diversity of source rocks produces considerable variation in the clay minerals formed. Therefore, each deposit is unique, with time-related variation within it. The greatest development of a weathering mantle takes place in a tropical climatic environment. Plant remains confirm that most ball clay deposits were formed under hot and wet conditions. Sedimentation of the clays had to be in fresh or low salinity water or clay minerals detrimental to whiteware manufacture would have been formed. Fresh water traps for the ball clay, sand and lignite sequences depended -on tectonic features, such as basin development along fault zones or lakes and lagoons on the edge of a large scale embayment. These factors for Devon ball clays were discussed by Vincent (1983). The combination of suitable source rocks, tropical climate, significant fresh water sedimentary environment

Jan 1, 1997

By T. F. Deems

The nature, usage and comparatively rare occurrence of ball clay is described. The importance of these white firing plastic clays in ceramics, particularly in the production of industrial sanitary ware and tiles, is emphasized. The US deposits are briefly discussed. What is known about relevant deposits in Brazil, Argentina, Colombia and Venezuela (the four largest ceramic producers in South America) is also described. The ceramic plants have been sited near the centers of population rather than the plastic clay deposits. At present, extraction is probably concentrated on surface residual deposits and lenses which require minimum investment. Native plastic clays are used exclusively in the tile plants, but in sanitary ware, they are often used as extenders of imported ball clays.

Jan 1, 1997