Search Documents

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 19601s, is still proceeding. The largest mechanical flotation machines available today have unit volumes in the range of 38 to 42 m3 (1,350 to 1,500 cft). In fact, the motivating forces of increasing capital and energy costs and decreasing ore grades, which created the need for large flotation cells, not only still exist, but are becoming more critical. This paper reports the development of an improved mechanism for these large flotation machines. The starting point in the development of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1982

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 1960's, is still proceeding. The largest mechanical flotation machines avail-able today have unit volumes in the range of 38.2 to 43.9 M3 (1,350 to 1,550 cft). Designs for mechanical flotation cells of unit volumes as large as 70.8 m3 (2500 cft) are available. The development of these "giant" flotation machines has been and continues to be motivated by the increasingly critical forces of higher energy and capital costs, decreasing ore grades, and lower (real) prices for the products. As an expansion of a previous publication, this paper reports the further development of an improved mechanism for these large flotation machines. The starting point in the develop¬ment of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which s is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1983

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) has been used by the mining industry for early fire detection in underground mines. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to integrate real-time AMS sensor data with NIOSH’s mine fire simulation program, MFIRE 3.0, to simulate and predict the spread of smoke that would provide assistance to mine fire emergency response personnel. Determining the heat release rate of a fire using the monitored sensor data was a critical component of the successful completion of this project. NIOSH researchers developed a direct method to calculate the heat release rate when a fire is within close range of sensors. However, this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire heat release rate for complicated scenarios where a fire is distant from sensors and airflow splits and merges are present. The method was validated using a fullscale diesel fuel fire test conducted in the Safety Research Coal Mine at the Pittsburgh Mining Research Division and can help mine operators and safety personnel make informed decisions during a fire emergency.

Jul 31, 2020

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) is used in the mining industry for early fire detection. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) have developed a direct method to calculate the fire heat release rate (HRR) when a mine fire is close to the AMS sensors, but this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire HRR using AMS sensor data at any location downstream of the fire. The method was validated using a full-scale diesel fire test conducted in the Safety Research Coal Mine at NIOSH’s Pittsburgh Mining Research Division.

By Anthony G. Fonseca

The acid leach-solvent extraction processing of oxide copper ores can be improved when selected cation additives are utilized. Bench scale testing showed improvements in both sulfuric acid leaching and solvent extraction processing. Treatment with the method to be described shows improvement in copper recovery in the acid leaching section as well as reduced acid consumption and reduced iron and aluminum dissolution. Processing the copper bearing leach solution with LIX-64N shows increased loading of the LIX reagent which relates to reduced aqueous and organic flow rates, reduced organic loss and inventory as well as a reduction in the size of mixer-settlers. The use of selected monovalent cations controls fluctuations within the pro- cessing system to accomplish the above named improvements. Additionally, these cations are totally compatible throughout the processing system and are quite inexpensive. Bench scale recycle data will be presented both for the leaching section and the continuous solvent extraction processing section up to (but not including) processing the loaded electrolyte. Material balances as well as major solution component monitoring will also be presented.

Jan 1, 1975

By M. M. Fine

One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. To cite some of them, in May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.3/ More recently, November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials, Evian, France, May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then current interest must be at a high level. To the casual observer of the metallurgical scene, the abiding and recurring attention to iron ore reduction outside the blast furnace must be somewhat puzzling in that so much research endeavor has resulted in so little commercial activity.

Jan 1, 1968

By H. D. Freeman

The Pacific Northwest Laboratory (PNL) is developing cover technology for uranium mill tailings that will inhibit the diffusion of radon to the atmosphere. As part of this cover program, an improved radon flux measurement system has been developed. The radon measurement system is a recirculating, pressure-balanced, flow-through system that uses activated carbon at ambient temperatures to collect the radon. With the system, an area of 0.93 m2 is sampled for periods ranging from 1 to 12 h. The activated carbon is removed from the radon trap and the collected radon is determined by counting the 214Bi daughter product. Development of the system included studies to determine the efficiency of activated carbon, relative calibration measurements and field measurements made during 1980 at the inactive tailings pile in Grand Junction, Colorado. Results of these studies are presented.

Jan 1, 1981

By L. G. Austin

The model originally proposed by Austin, et al., has been modified in the light of further investigation of the breakage laws in SAG milling. The model uses a fully-mixed reactor for short L/D mills and calculates the breakage of small particles by the nipping action of balls and pebbles. The autogenous self-breakage of larger lumps is treated as an effective means of fast breaking rock and much slower breaking rock. Experiments show that fast autogenous breakage can be treated as a first-order breakage with an overall specific breakage rate which incorporates fracture and chipping. Similarly, slow breakage incorporates fracture and abrasion. Autogenous breakage is cushioned by the accumulation of fine material. Simulation results are compared to results from tests in a 2 m diameter continuous pilot-scale SAG mill. Future work is discussed.

Jan 1, 1985

By Thomas E. Ban

The continuous sintering process was invented more than 60 years ago by two metallurgists, Arthur S. Dwight and Richard L. Lloyd, who saw a need for automation in mineral processing. Their specific objective was to beneficiate copper ore by desulfurizing and agglomerating it for copper blast furnace smelting at the Cananea plant in Mexico1. Since their early development the process expanded widely in scope, size, and application. The current worldwide sintering applications exceed 250 million tons per year for agglomerating ores of lead, manganese, zinc, and iron. Sintering is also widely used for production of sintered lightweight aggregate from clays, shales, and fly ash. The continuous sintering process took on wide expansion during the 1960's in foreign countries. Plants for production of approximately 135 million tons per year were built in these countries for sintering iron ore fines as shipped from new iron ore projects of Canada, Liberia, India, Brazil, and Australia. This expansion represented construction of approximately 80 new sintering plants, some as large as 15 thousand tons per day production on a single large sintering machine. Sized self-fluxing or highly fluxed sinter has become recognized as a premium blast furnace charge and has enabled blast furnaces of Japan and Europe to produce upwards of 10,000 tons of metal per day with coke rates less than 1,000 pounds per ton of metal. This coke requirement is practically 50 percent of the ordinary rates achieved during the early 1950's when the peak blast furnace production was less than 113 of the current records.

Jan 1, 1975

By Richard R. Radel, Jack Barry

Contract required excavating 2,000 If of 14' horseshoe tunnel in rock, a 95' deep work shaft on shore, and a 50' deep intake shaft located in the middle of the Niagara River just above Niagara Falls. Large quantities of H2S were encountered in the range of 20 PPM with ventilation. Peak levels of 40 PPM were recorded. The original designed ventilation system required only a volume of 10,000 CFM to meet OSHA requirements. The volume of air was increased to 50,000 CFM to dilute the H2S to al- low workmen to work and comply with OSHA H2S action levels. The second phase of the tunnel consisted of placing 72" ID X 20 foot long concrete reinforced pipe in the tunnel. When the tunnel was holed through and both shafts were open, a substantial amount of work was required to take place in the shafts which eliminated the possibility of placing a bulkhead to secure proper ventilation. The ventilation team designed a jet system airlock. The design of this system was to bring fresh air down the work shaft in two duct systems; one 30" diameter and one 24" diameter. Following the excellent work of Jan Wolski (7th Mine Ventilation Symposium chapter 58) our design incorporated nozzles located approximately 100' in by the work shaft. The velocity of the 24" diameter duct was 6,365 FPMD2.2 MPH. The velocity of the 30" diameter duct was 6,117 FPMl69.5 MPH. Both systems were on blow and being that air expands at 3112 degrees per side this high velocity of air expanded and created an air bulk head through which men and the large sections of concrete pipe could be passed without any delay or additional cost to the project.

Jan 1, 1997

By J. Leonard Frame

A coal-fired fluidized bed combustion (FBC) system will be installed at the Owatonna Tool Company, Owatonna, Minnesota. Two FBC combustors will burn solid fuels: coal, petroleum coke, and wood and paper wastes. Crushed dolomitic limestone will be used to control sulfur emissions to EPA limits. The combustors will supply indirectly heated hot air and hot water for paint drying operations, washing processes, and space heating. The program is sponsored by the United States Department of Energy and the Owatonna Tool Company, and is one of five programs designed to demonstrate industrial applications of coal-fired fluidized bed equipment. The paper will describe the combustion system and the results of development tests with dolomitic limestone for sulfur emission control.

Jan 1, 1978

By D. W. Ashman

Today the electrolytic zinc industry is facing unprecedented environmental pressure and low metal prices. Zinc plants have to decide how they will dispose of iron residues in an environmentally friendly way without major capital expenditures. Only low-cost producers will survive, so companies must continuously improve to stay competitive. Therefore, the challenge of the process engineer is to find innovative solutions to the industry's problems. This paper reviews the status of electrolytic zinc processing and provides some insight into how the industry will respond to the pressures facing it

Jan 1, 1993

By Norm Greenwald

The Environmental Protection Agency ("EPA") has been attempting to develop a federal regulatory program for mine waste under Subtitle D of the Resource Conservation and Recovery Act since 1986. Recent regulatory and legislative events are now bringing this goal closer to reality. This paper discusses the mining industry's perspective on a number of the issues currently being addressed at EPA's Policy Dialogue Committee and in Congressionally-sponsored negotiating sessions.

Jan 1, 1992

By Leping Liu, Sachin Urade, Li-Ting Chen, Pengbo Chu

This study aims to provide industrial perspectives on the current U.S. metal mining engineering education and areas for improvement. An online survey was designed to seek opinions from the U.S. mining industry. Findings indicated a shortage of qualified graduates from the current U.S. metal mining engineering education system. The qualifications that need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications, such as the ability to acquire and apply new knowledge as needed and sufficient field experience. Respondents recommended enhancing collaborations between industry and academia.

Oct 1, 2023

By Leping Liu, Li‑Ting Chen, Sachin Urade, Pengbo Chu

Mining industry requires constant adaptation to its practices in response to the dynamic change of the societal demand. Little information exists regarding how the US metal mining engineering education is prepared to meet with its industry needs due to the increase in critical minerals driven by the green energy transitions. This study aims to provide industrial perspectives on the current US metal mining engineering education and areas for improvement. An online survey with both closed- and open-ended questions were designed to seek opinions from the US mining industry. Findings indicated a shortage of qualified graduates from the current US metal mining engineering education system. The qualifications need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications. The most desired ones in the next 5 years include an ability to acquire and apply new knowledge as needed and sufficient experience in the field. Respondents, regardless of the nature of their affiliated mining companies, unanimously recommended that collaborations between the industry and academia should be enhanced. The analysis of the results concluded four recommendations: (1) involve more multiple stakeholders in reforming mining education programs, (2) reinforce field experiences as a key part of mining engineering education programs, (3) enhance a closer collaboration between academia and industry, and (4) integrate emerging technologies (e.g., artificial intelligence/virtual reality) guided by pedagogical theories into new mining engineering curriculums.

Jun 26, 2023

By James R. Jones

The purpose of these opening remarks is to establish a viewpoint, which will form part of the basis for later discussion between panel members and between the panel and the audience. Important issues will be identified. These ideas in the form of questions and answers, hopefully, will provide the necessary background for the ensuing dialogue. Is There An Urgency? We do not believe there is the urgency for immediate control legislation that has been depicted by some Congressional sources, environmental groups, and certain segments of the press. Emissions of sulfur oxides in the United States have decreased 15% during the 19701s, even though the use of coal by electrical utility power plants increased nearly 80%. That trend will continue as the older plants are phased out of operation and are replaced with newer plants, which must meet the New Source Performance Standards (NSPS) requiring the use of "scrubbers" to reduce sulfur dioxide emissions by 70% or 90%. The present Clean Air Act Amendments of 1977, by allowing the logical progression of economic events- -depreciation, retirement, replacement, and growth--will produce approximately a 50 % reduction in SOX emissions by the year 2015.

Jan 1, 1984

By David P. Kimball, Dalva L. Moellenberg

On May 21, 1990, EPA released its Strawman II draft program for mining wastes. It proposes to expand RCRA regulation of mining operations to include materials other than wastes. Strawman I1 would establish strict standards for the states to follow, rather than technical guidance. It proposes to establish performance standards; design criteria; monitoring requirements; and corrective action, closure, post-closure, and financial assurance requirements. It suggests "pollution prevention" concepts for mining operations. This paper explores the Strawman II proposals, particularly the technical criteria, and addresses several of the important concerns raised by industry.

Jan 1, 1991

By III Kimball

Mining wastes have received individual attention under the Resource Conservation and Recovery Act (RCRA) since its inception, in recognition of the special characteristics that distinguish mining wastes from other solid wastes. The Environmental Protection Agency (EPA) has recognized that: - Mining wastes are generated in much larger volumes than other industrial wastes. Most material handled in mining is waste (over 99% in many cases) and not marketable product, whereas waste is a small portion of raw materials used in most industries. Consequently, controls used for hazardous wastes may be technically infeasible or economically impractical. - Nearly all mining waste is managed at the site of generation and is land-disposed. . - Mining wastes typically pose lower hazards than other industrial wastes. Mining operations are located predominantly in sparsely populated areas and in arid or semi-arid areas with little surface water runoff and deeper water tables.

Jan 1, 1990

By Snehamoy Chatterjee, Dharmasai Eshwar, Aref Majdara, Rennie Kaunda, HUGH MILLER

The U.S. mining industry has made progress in reducing accidents and injuries, but interpreting safety data remains difficult due to changes in workforce size and productivity. The Mine Safety and Health Administration (MSHA) uses tools like the pattern of violation (POV) and significant & substantial (S&S) calculator to monitor safety, though these have limitations. To address this, we developed an information entropybased risk (IER) index that combines various safety metrics, including citations, penalties and injuries. Using data from 2011 to 2020, the IER index was validated with statistical methods and clustering algorithms to ensure it accurately reflects risk levels. The analysis showed clear differences in risk across mining sites, proving the index’s usefulness. The IER index was then applied to a coal mine to demonstrate its effectiveness. This new tool can help mining companies better assess their safety risks and take action to improve workplace safety.

Nov 1, 2024

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009