Search Documents

By Rick Deschamps

"Fountain Slide is located approximately 10 mi (16 km) northeast of Lillooet, British Columbia, Canada, within the Coastal Mountain Range, and has been locally active since the 1970s. The project site is located near the base of the relic Tunnel Mountain landslide. The progressive movements have posed a significant challenge to British Columbia (BC) 99, the main north-south highway in the region. The slide began affecting the British Columbia Railway Company (BCR) tracks in the 1990s. In 2004, the Canadian National Railway Company (CN) acquired BCR and, during the next 11 years, undertook measures to stabilize the rail bed. Some of the measures undertaken include numerous track realignments, a shotcrete and soil nail wall, an anchored soldier pile-and-lagging wall, and adding a row of anchors to the wall. For many years, the measures had proved successful until mid-2014 when it was observed that the slide retrogressed uphill of the tracks. Since that time, the slide movements typically ranged between 5/32 and 0.4 in (4 and 10 mm) per day, leading to extreme distortion of the earth retention system and the need for frequent track realignment.In the spring of 2016, CN issued a request for proposals (RFP) for a designbuild solution with the expectations of: (1) a safety factor greater than 1.2, (2) considering only the currently identified retrogressive blocks that extend to about 200 ft (61 m) above the track; and (3) minimizing activities outside the current easement. It was also communicated that there was a possibility that a portion of the line may have to be abandoned if the proposed remediation was cost prohibitive.The fact that the existing slide was a small fraction of the relic slide was intimidating. The relic slide extended for approximately 1.0 mi (1.6 km) above the uppermost retrogressive block that was now affecting the rail line. Other areas of concern included:"

Jan 1, 2017

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By Tony Amis, Marco Barla, Alice Di Donna

"Energy geostructures are becoming an increasingly popular solution around the world for Developers looking to reduce CO2 and system running costs. Energy geostructures are geotechnical structures that provide both the important role of structural stability while also acting as a heat exchanger with the ground, enabling the supported buildings and or infrastructure to be heated and cooled using the principle of low enthalpy geothermal systems. The main advantage of this innovative technology with respect to standard geothermal plant is the reduction of the initial installation costs and construction schedule benefits, compared to installing conventional geothermal solutions, largely due to the additional use of structures which would be constructed in any case. However, it is important with respect to energy geostructures that additional aspects need careful consideration. For this very reason, several research studies have been carried out over the last decade on this subject and a number of real case studies have been monitored and analysed. The key difference with respect to conventional shallow geothermal systems are mainly related to the geometry, which is imposed by the geotechnical project, and the need to ensure that the primary structural role is always guaranteed. Special boundary conditions, the reduced depth, the influence of atmospheric external temperature can also play an important role for energy geostructures. They can affect, both energy efficiency and, the geotechnical behaviour because of the possible thermal induced mechanical effects. This paper presents a picture of the current situation regarding energy geostructures and their peculiar features, and collects available data to provide a reference framework. Data has been collected from literature and personal communications and then processed to provide easy-to-read charts useful for practical consultation at a glance. This paper provides, an indication of the distribution of such systems worldwide, their spread in time, and a global view of their actual efficiency from the structural, energy, economic and environmental point of view.1. IntroductionEnergy geostructures are becoming an increasingly popular consideration around the world. Energy geostructures are geotechnical structures with a dual role of providing structural stability and the ability to exchange heat with the ground, to provide low carbon heat and coolth to supporting and or adjacent buildings and infrastructure, using the principle of low enthalpy geothermal systems (Barla and Di Donna, 2016; Laloui and Di Donna, 2013). A closed circuit of high density polyethylene (HDPE) pipes is embedded in the concrete, and a heat carrier fluid circulates through them exchanging heat with the ground. The HDPE pipework circuit inside the geostructure is linked to one of the above buildings or infrastructure through a heat pump, which adapts the temperature of the circulating fluid to the heating (winter mode) and cooling (summer mode) needs. In this way, heat can be injected into the ground during summer and extracted from it during winter. In principle, all structures in contact with the ground can be used as energy geostructures. The first examples of energy geostructures date back to the eighties in Austria and were mainly piles and shallow foundations. A decade later, Henderson et al. (1999) reported on what would appear to be the first successful use of geothermal energy piles in the US, with loops incorporated into the foundation for a hotel in Geneva, New York. As was their use in this New York case history, the typical geothermal energy pile application is used in conjunction with additional closed loop boreholes to provide the required energy capacity for a structure. Interestingly the report concludes that the geothermal energy piles had a better heat transfer performance than the borehole field. The first energy walls appeared slightly later, while still today only a few experimental cas"

Jan 1, 2017

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By H. R. Taber

The extensive subject area "Engineering Practice of Ground Improvement" will be treated within the limitations of space and the writer on the basis of personal practice and experience?largely in Northern California over a period of some thirty-six years and, in "ground improvement" work, with an emphasis on transportation facilities. The stress is on improvement of ground conditions, rather than on techniques of improving inherent earth materials characteristics. "Ground improvement" is discussed as engineering resolution of existing or emergent earth materials defects or deficiencies?that is, as the technically feasible procedures best adapted to achieving a required level of service within physical, economic, social and other constraints. A "required level of service" concept is presented as a tool in evaluation of appropriate ground improvement work.

Jan 1, 2010

By M. Melih Demirkan, Juan J. Gutierrez, Raghav Ramanathan

"As the capital of the United Arab Emirates (UAE), Abu Dhabi is one of the world’s fastest-developing cities. To sustain its significant growth rate, Abu Dhabi must surmount challenging engineering problems in the most efficient manner. One of the challenges facing Abu Dhabi is ground settlement caused by poor groundwater control practices in inherently difficult subsurface conditions. For construction projects in Abu Dhabi located near the Arabian Gulf, groundwater is frequently encountered and must be accounted for and addressed during design and construction. Abu Dhabi City CenterRecently, the Abu Dhabi government developed a geodatabase by digitizing, processing and qualifying an extensive amount of existing information (i.e., more than 26,000 borehole logs). Because of the evaluation and processing of the geodatabase, detailed maps of geotechnical and hydrogeological surface features were generated using 3D modeling. Ultimately, the geodatabase was used to develop risk maps indicating geohazards, such as sabhka (or salt flats), uncontrolled fill and cavities. This information identifies the location and extent of the areas vulnerable to surface subsidence. Dewatering can change pore water pressure, which, in turn, alters the effective vertical stress in a soil mass and can affect groundwater chemistry. Changes in pore water pressure and groundwater chemistry can significantly affect soil and rock. The potential effects of dewatering include:• Change in effective stresses and shear strengths in soils• Increase in seepage velocities and pressures• Erosion or transport of soil particles and piping• Settlement• Collapse of subsurface cavities or voids• Transport of groundwater containing contaminants• Dissolution of soluble materials, such as rock salt or gypsum"

Jan 1, 2017

"What can we do in ground engineering to reduce damage to the environment, to repair historic pollution, to reduce our demand on basic resources and to reduce the carbon footprint of our industry? Some developments in geotechnical engineering are already heading in the right direction. These include reductions of ground pollution from grouting, improved dewatering procedures and advances in mix-in-place processes, ground improvement and jet grouting.There is increased interest in certain promising technologies (for example, drilled partial or full displacement piles), but this approach remains for the moment somewhat avant-garde. These piles require substantially greater power to install, and the overall sustainability balance for general application has yet to be shown to be in their favour. They are particularly suited to polluted sites where the problem of dealing with spoil would be costly and where, in the past, driven cast in-situ piles would have been employed. Drilled displacement piles offer some environmental benefit over driven piles in that they cause far less drawdown of potentially contaminated near-surface ground into sensitive, underlying aquifers.There is also great interest in various means of increasing the frictional capacity of bored piles, both conventional auger and continuous flight auger (CFA) piles, by threading or ribbing the soil/pile interface. The increase in adhesion capacity allows reduction in the pile dimensions necessary for a specific load. This obviously leads to less construction waste, but also to less permanent material consumption in the piles and also in the pile caps.The role of ground improvement remains significant for brown land sites and lower capacity foundations. Information technology (IT) has improved the quality assurance of stone column construction, for example. From the sustainability point of view, this is a good news method; here is no cement, no pollution and little obstruction to future redevelopment. We now need to introduce recycled crushed materials instead of natural aggregate as general practice and the technique’s green credentials will be really compelling."

Jan 1, 2009

By Ken MacLeod

A development at 83 Queens Road in Melbourne, Australia required construction of a three level basement. The normal geotechnical constraints of excavating adjacent to an existing relatively new building were challenging enough for the complicated soils profile occurring at the site. An additional significant challenge faced by the designers, was the requirement to excavate underneath the entire footprint of an existing heritage listed building, known locally as the Mansion, in the centre of the site. Maintaining the structural integrity of that building was afforded the highest priority during the 10m excavation. This paper describes geotechnical aspects of the analysis, design and construction of the secant retention system adjacent the new building and support of the Mansion enabling the 10m excavation to proceed without causing damage to the structure. The secant wall comprised hard-soft interlocking piles constructed using CFA methods. CFA piles along the length of the Mansion provided short term support, with the building load being transferred to the piles by large steel beams jacked under the building. Survey results confirmed that movements of the retaining wall and also the load bearing piles were minimal and well within design expectations.

Jan 1, 2006

By Carl D. Ealy

Work is being done to web enable the FHWA Deep foundation Load Test Database. Originally designed to function in the client server environment via modem, access to the database both for data maintenance and user queries has been upgraded to take advantage of the Internet and current and future information technology innovations. The DFLTD will be part of an Automated Geotechnical Information and Design Aid System, the object of which is to assist those involved with managing and maintaining our nation's highway infrastructure. The system will also meet the needs of university and other research institutions for a statistically meaningful source of high quality data for the development and verification of improved analysis methods, in-situ testing methods, etc.

Jan 1, 2002

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By James V. Errico

On October 1, 1993 the regulations for assessing and cleaning up contaminated soil and groundwater in the Commonwealth of Massachusetts were revised. These new regulations, known as the Massachusetts Contingency Plan (MCP) 310 CMR 40.0000, were developed to keep routine releases out of the regulatory system and rely on private parties to handle most releases without Department of Environmental Protection (DEP) oversight. An integral part of the new MCP is the Licensed Site Professional (LSP). An LSP is required to handle activities and render opinions once a site enters the MCP. These regulations must be adhered to where ever a release has occurred, including construction sites. A brief overview of the new MCP is given below; see attached MCP Flowchart for graphical summary. Entering the MCP Process A release of oil or hazardous material (OHM) to the soil or groundwater above applicable reportable quantities (RQ's) or reportable concentrations (RC's) will require notification to the DEP and compliance with applicable provisions of the MCP. RQ's and RC's are listed in the MCP (310 CMR 40.1600) for most compounds that are typically encountered. For each compound there are two RC's for soil (S-1 and S-2) and two for groundwater (GW-1 and GW-2). The S-1 and GW-1 RC's apply to sites that are environmentally more sensitive, as a result they are lower than the S-2 and GW-2 RC's.

Jan 1, 1994

By Uwe Hess

For the Danish landworks for the coming fixed link between Denmark and Sweden across the Øresund the focus has been on the environmental aspects of the construction and operation of the facilities. This paper describes how the environmental objectives pertaining to the project have influenced the design and construction of one of the major elements of the Danish landworks, i.e. the tunnel in Sydhavnsgade and under Sydhavn Station. The chosen construction methods for the construction pit bracing and the groundwater lowering will be described along with the observed effects on the environment as shown by simulated or measured values for noise impact, settlements, pumped groundwater and extension of the drawdown cone.

Jan 1, 1996

By Deshmukh A. M.

Existence of human beings and their relationship with the nature is symbiotic. The lack of perspective and negligence of nature disturbs the equilibrium of environment and causes unprecedented disasters. Geotechnical engineers are directly concerned with hazards of nature as elements of foundation and of nature are inter related. Rational design and construction of foundation can be accomplished only after properly assessing influence of environment This paper briefly delineates impacts of environment and human activities and presents salient features of management of impacts through the system of deep foundation. Limitation of negative effects and enhancement of positive developments necessitates eco-consistent planning of engineering projects based on the geotechnical aspects of environmental impact management.

Jan 1, 1996

By Tony P. Suckling

This paper presents a case study of a piling contract undertaken at Keble College in Oxford in the year 2001. Unusually, and for the first time in the United Kingdom, piles were successfully constructed containing a network of plastic pipes, which are subsequently to be connected to the heating and cooling system for the new building. The pipes cast in the piles facilitate the transfer and storage of geothermal energy between the structure and the underlying ground mass, allowing the new building to be both heated in winter and cooled in summer economically and in an environmentally friendly way. The philosophy of the geothermal pile technology is presented, together with the modified pile construction techniques employed on the site.

Jan 1, 2002

By A. Paviani

The subject of this session is "Equipment Installa­tion, Recent Developments". This is a subject which is not usually addressed at conferences of Foundation Engineering. It is rare to find sessions dealing with the technological side of deep foundations, a subject which only recently seems to have aroused sufficient interest at national and international conferences. It is therefore natural for the subject of "Equipment", or the tools used to implement the various "technologies", to be over­looked or mentioned only occasionally during the discussion of other issues. At conferences, most of the attention is attached to research and to the theoretical interpretation of the performance and behaviour of deep foundations, as well as to establishing the most suitable calculation algorithms and approaches for the study, design and control of foundation structures. It is almost as if the subject of equipment is felt to be less important or, perhaps, that it is considered to belong more strictly to mechanical engineering than to civil engineering.

Jan 1, 1994

Volume 1 pages 665-671 Title should read as Dynamic pile testing of H-piles at HDB sites J.Wei, Y. S. Heng, C. S. Lok, M. K.Chong Housing and Development Board, Singapore 'tons' should read as 'tonnes' Para 3.2 fourth equation (page 667) [TC = t2 v.dt t = 0 should read as TC = t2 v.dt - s t = 0]

Jan 1, 1994

By A. J. Partos

Table 4, Page 311 Table 4 Experimental Parameters from Straight Line Interpretation of Mohr Failure Envelope [ ]

Jan 1, 1991

By H. Meseck

Dynamic pile test methods to establish the bearing capacity of driven piles were developed in the USA more than 20 years ago. In the Federal Republic of Germany, the first dynamic pile tests were carried out at the end of the 70's. Today dynamic pile tests are successfully used to establish the integrity and bearing capacity of driven and bored piles. The Institute of Foundation Engineering and Soil Mechanics at the Technical University of Braunschweig has developed its own method of measuring and evaluation for the execution of dynamic pile tests. The principles of the dynamic pile tests, the measuring and evaluation plant as well as the experience gained with it in the examination of cast-in-place piles are presented in this contribution.

Jan 1, 2010

By Cem Akgüner

The displacements of axially loaded single piles are analyzed with an approach based on elasticity. Young?s modulus and Poisson?s ratio of the soil encompassing a pile are the unknowns required as input to obtain predictions based on the elastic method. Attention is directed towards Young?s modulus because the range and variability of Poisson?s ratio is not significant in displacement calculations. A database of axial pile load tests established for the California Department of Transportation (Caltrans) is investigated. All of the tested piles were driven into the ground. Measurements of displacements and loads were made only at the top of the pile. First the magnitude of displacements is determined up to loads that are half of the failure load measured from pile load tests. Various correlations for Young?s modulus are then employed to determine how accurately each predicts the actual measured displacement. The chosen correlations utilize the routinely available parameters of laboratory triaxial undrained shear strength for cohesive soils and standard penetration test blowcount for cohesionless soils.

Jan 1, 2008

By Arash Khosravifar Ph. D. P. E., Thomas Torkelson P. E., Milad Souri Ph. D. P. E.

Kinematic demands from lateral ground deformations can be a major cause of damage to maritime and highway transportation structures such as wharves, piers, and bridges. These kinematic demands are different from the ground deformations in the free field in that the resisting forces from piles will reduce the ground deformations to some extent (i.e., pile pinning effect). Current design codes for wharf structures allow the beneficial resisting forces from pile pinning effects to be incorporated in pseudostatic slope stability analysis (e.g., ASCE/COPRI 61-14). While design guidelines that are specifically developed for bridge foundations provide recommendations on how to incorporate the pile pinning effects (e.g., Caltrans 2012), their applicability to wharf structures need to be evaluated. This study uses the results of a large-scale centrifuge test on a pile-supported wharf structure to evaluate the accuracy of available Newmark sliding block analysis in estimating the lateral ground deformations. Pile pinning effects are incorporated based on the approach outlined by Caltrans. The results of this study support the use of existing pile pinning methods that were primarily developed for bridge foundations in maritime structures (e.g., wharves and piers). It was found that median Newmark displacements provide a good estimate of the permanent end-of-shaking displacements and that the median plus 1 standard deviation Newmark displacements provide a good estimate of the peak transient displacements. Design considerations for use in the Newmark sliding block analysis to estimate the kinematic demands on piles are discussed.

Oct 1, 2022