Search Documents

By Francis Breton, Daniel Larouche, Pierre Heugue, Rémi Martinez

"Nowadays, in order to fit environmental restrictions, automotive markets are demanding cast aluminum alloys working at high temperature (180–300°C). New generations of alloys are required for higher strength components in engine downsizing or start-stop systems which lead to higher loading and higher specific power and stretch current materials to their limits. Recently, transition metals, such as zirconium and vanadium, have been added as alloying elements into an AlSi7Cu3.5Mg0.1 alloy to improve physical, mechanical, thermodynamic properties with the aim of increasing service life of parts. In such alloys, the best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, including: solutionizing, quenching and artificial aging. This study is focused on the modified AlSi7Cu3.5Mg0.1 cast alloy with Mn, Zr and V additions for high temperature application. The characterization of the cast alloy in this study, firstly, helps to evaluate and understand its performance both chemically and structurally according to their physical state: as-cast or as-quenched. Comparison of precipitation kinetics between a binary Al-3.5%wt.Cu alloy and the AlSi7Cu3.5Mg0.1 (Mn, Zr, V) alloy has been characterized by differential scanning calorimetry, TEM observations and micro-hardness testing. The Kissinger analysis was applied to extract activation energies from non-isothermal DSC runs conducted at different stationary heating rates. The study focuses on the impact of the chemical composition such as Si content on the kinetics parameters.INTRODUCTION Pure metal Aluminum shows poor mechanical properties and its malleability is high, that is why alloying elements are added to the mixture before casting to improve physical, mechanical and thermodynamic properties (Javidani, 2015); such as Silicon (Si) for casting properties (castability, cold crack capability, wear resistance, shrinkage behavior), Magnesium (Mg) and Copper (Cu) to generate precipitation hardening systems. Aluminum hypoeutectic alloys (<12% Silicon) with Cu, Mg additions used in the automotive industry for manufacturing mechanical parts (Larouche & Javidani, 2014) are mostly subject, after casting, to precipitation hardening heat treatment (Mohamed & Samuel, 2012) according to specifications and associated standards. The best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, generally including: solutionizing, water quenching and artificial aging (Manente & Timelli, 2011). Hypoeutectic aluminum-copper alloy with amount of Cu around 1 to 4.5wt% is an elementary case for precipitation in heat treatable aluminum alloys. Researchers essentially focused their work on the full precipitation sequence of binary Al-Cu alloy during aging which is presented below."

Jan 1, 2018

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By M. A. Vasina, I. A. Matveeva, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"Using the calculated (Thermo-Calc software) and experimental methods (SEM, TEM, EMPA, DSC, XRD, etc.) the phase composition, structure and hardening of aluminium alloys of the Al-Ca-Zn-Mg system were studied in the following range: 2. 5%Mg, up to 10% Ca, and up to 14% Zn (wt%). Fragments of this quaternary phase diagram in the aluminium corner were constructed, including the liquidus surface, as well as some vertical sections. It was shown that the relatively large amount of zinc enters in the Ca-containing phase, which formula can be described as (Al,Zn)4Ca. An increase of Zn content leads to formation of Al4Ca primary crystals at lower concentrations of calcium. The eutectic (Al)+(Al,Zn)4Ca has a fine structure and aluminide particles are capable to spheroidization during the heat treatment at temperature 500 C. The maximal level of hardness observed on calcium containing alloys was higher than 200 HV, what gives the reason to expect good strength properties. With an example of an Al-9% Zn-2,5%Mg-3,5% Ca model experimental alloy based on the (Al)+(Al,Zn)4Ca eutectic, a principal possibility of manufacturing thin rolled sheets was demonstrated.INTRODUCTION Aluminum alloyed with calcium was first studied in 1970-80s by such authors as Piatti (1976), Moore (1978, 1980), Il'enko (1985), Swaminathan (1990), and Perez-Prado (1997) as superplastic materials. In particular, the alloy systems Al-Ca-Zn were studied (Il'enko, 1985, Swaminathan, 1990, Perez-Prado, 1997). For some time there was no new published works concerning the aluminum-calcium alloys. During the last years many works were published dedicated to the calcium alloying of magnesium alloys (Kim, 2011; Xu, 2011; Aljarrah, 2008; Bakhsheshi, 2014). This urged the authors (Belov, Naumova & Akopyan, 2016) to start studying cast and wrought aluminum-calcium alloys for construction (2008–2014). There is almost no information in the literature concerning triple and more complex diagrams of the aluminum-based system states with calcium and other elements. In recent work, parts of the state diagrams are plotted for the aluminum angle zone: Al-Ca-Mg-Sc (Belov, Naumova & Bazlova, 2016), Al-Ca-Ni-Sc (Belov, Naumova & Bazlova, 2017), Al-Ca-Si-Sc (Belov, Naumova & Akopyan, 2017) and others. Special attention was paid to the study of the system Al-Ca-Zn-Mg (Naumova, 2017). Based on this system creation of advanced extra-high tensile alloys is planned. Wrought extra-high tensile alloys series 7??? based on the system Al-Zn-Mg-Cu are well studied."

Jan 1, 2018

By Ram Song, Yohei Harada, Shinji Kumai, Kazuho Otsuka

"Recently, vertical-type high-speed twin-roll casting (HSTRC) has been developed. The HSTRC shows extremely high cooling rates over 1,000 K/s even at the mid-thickness area. The fabricated strip has many metallurgical characteristics; super-saturation of alloying elements, fine solidified structure, and homogeneous distribution of fine constituent particles. In Al-Mn based alloys, the Mn alloying element can be supersaturated in the a-Al matrix and also form Mn-containing constituent particles during solidification. The Mn supersaturation and the distribution of primary/secondary particles in cast products affect the metallurgical behavior in the down-stream processing and can improve mechanical properties of the final products. In this study, Al-Mn based alloy strips were fabricated by HSTRC with various Mn contents. The solidified microstructure, constituent particles and its distribution, and Mn solubility were investigated in the as-cast condition. Due to the high cooling rate of HSTRC, fine constituent particles were homogeneously distributed, and coarse intermetallics were not observed. Mn solid solubility was estimated by electrical conductivity. The estimated Mn solubility was equivalent between strip surface and mid-thickness area.INTRODUCTION Al-Mn based alloys, as non-heat treatable wrought aluminum alloys, are widely used in packaging and heat exchanger for automobile industry. Besides Mn, Al-Mn based alloys often contain Fe and/or Si as alloying elements or natural impurities. During solidification, Mn can be super-saturated in the Al matrix, and also form Mn-containing constituent particles. Additionally, in the subsequent thermal-mechanical processes such as homogenization, rolling, and intermediate annealing, Mn in solid solution precipitates out of the Al matrix as secondary particles. The size, distribution, type, and the amount of dispersoids including constituent particles affect to texture evolution, recrystallization behavior, and final mechanical properties of wrought Al-Mn based alloys (Huang et al., 2016; Huang & Marthinsen, 2015; Engler et al., 1995; Muggerud et al., 2013). Therefore, controlling the initial level of Mn super-saturation and the distribution of constituent particles are important in the cast Al-Mn based alloys."

Jan 1, 2018

By F. Andrieux

"Extruded aluminum profiles are increasingly used for lightweight vehicle construction. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles, not only the stress state but also the orientation influenced both the deformation and damage behavior. For the material characterization smooth tensile tests were performed in six orientations, both stress-strain curves and r-values were registered. Moreover notched tensile and shear-tension tests were performed in three directions. Finally punch specimens were tested to investigate biaxial loading. Digital image correlation (DIC) analyses were performed to determine local strain values such as critical values at failure. Numerical investigations were conducted with the strain based damage model GISSMO, which is well suited and widely applied for crash simulation. For a strain based failure model the choice of the deformation model is crucial. Deformation models with increasing complexity were investigated to find the best compromise over all experiments. It was found that there is still a great requirement on development of a material model which describes the orientation dependence of the hardening behavior over all stress states in order to be able to use a strain based failure model reliably.INTRODUCTION Weight reduction is an important step for less energy consumption and as a consequence aluminium is increasingly used in automotive parts. An important field of application is the well-established aluminium extrusion which allows the realisation of quite complex shapes of profiles required for an innovative lightweight design with integrated functions. Typical applications are chassis parts, bumpers, crash elements, air bags, etc. Especially the Al–Mg–Si medium strength alloys of the 6000 series can be easily extruded to form complex profiles and prevail for extrusion. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles not only the influence of the stress state but also the orientation with respect to the extrusion direction have an influence on both the deformation and damage behavior and need to be characterized. The effect of orientation on deformation behavior has been intensively investigated in the last decades and material models haves been proposed (e.g. Barlat & Lian, 1989; Barlat, Lege, & Brem, 1991; Barlat et al., 2003) to describe accurately anisotropic behavior. However it can be noticed that the parameters of anisotropic material models often rely on the yield stress in different directions, which means that the effect of strain hardening is not automatically accounted for. The accuracy of the models at large deformation is not guaranteed and has to be verified. In contrast to deformation models both the characterisation and the modeling of anisotropic damage behavior are not systematically studied. Isotropic failure models based on a critical strain as function of stress triaxiality (ratio of the hydrostatic stress to von Mises equivalent stress) are widely used for crash application (e.g., Bai & Wierzbicki, 2010; Sun, Andrieux & Feucht, 2009; Sun et al., 2013). The mechanisms of failure are manifold and not fully understood; to develop an anisotropic failure model it is mandatory to also have experimental data in different orientations for loading scenarios other than uniaxial tension, e. g. shear, biaxial tension, which implies an extensive experiment plan. This makes the development of failure models more challenging than deformation models for which it is possible to develop a reasonable anisotropic model using the framework of yield function and calibrate the material parameters based on results of tensile tests in different directions. Moreover the development of deformation and failure models are intricate as the variables governing the damage evolution are predicted by the def"

Jan 1, 2018

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By G. Scamans, J. Lazaro-Nebreda, Z. Fan, J. B. Patel

"Melt quality is crucial for both continuous and shape casting of light alloys and in order to improve it, removal of excessive inclusions, accumulated impurities and unwanted gases becomes necessary. To address this problem, a new multi-purpose high shear liquid metal treatment technology, based on intensive melt shearing by a rotor/stator unit, has been developed. The device ensures achieving uniform temperature and chemical composition and an efficient dispersion of gas and solid phases in the melt with minimal disturbance of melt surface, and can be used, among other things, for de-gassing and de-ironing of Al-alloy melts. Efficient degassing is achieved by dispersing each argon bubble into many small ones, which significantly increases the overall surface area of the bubbles and the time they remain in the melt capturing hydrogen before reaching the surface. This allows using much lower inert gas flow and mixing times than conventional rotary degassing. When applied to Al-alloy scrap, with accumulated iron, the high shear melt treatment speeds up the nucleation and growth of primary Fe-rich intermetallic particles, allowing a faster removal rate. Therefore it reduces processing times, increasing recycling productivity, and facilitates full metal circulation of secondary Al-alloys.INTRODUCTION Aluminium and magnesium alloys are widely considered in various industrial sectors for the purpose of weight saving (Polmear, 1995). In particular, they are used in the automotive sector, where components are mostly manufactured by high pressure die casting (HPDC) because of its simplicity and relatively low cost, but efficiency and mechanical properties are quite low compared with other processes. To date, the main focus to overcome this problem has been for improving the HPDC machinery (Dahle, 2001) but little attention has been paid to the opportunities of controlling the nature and quality of the molten metal supplied to the die. In this way, liquid metal treatment, which involves a variety of physical and/or chemical processing methods to improve melt quality prior casting, is crucial for both continuous and shape casting products."

Jan 1, 2018

By J. Fixter, P. Prangnell, Z. Pinter, E. Eimer, B. Chehab

"High deposition rate Wire and Arc Additive Manufacture (WAAM) can provide benefits to the aerospace industry, including a reduction in lead time, reduced material waste and, through higher solidification rates, refinement of the as-built microstructure relative to a cast material. However, candidate 2xxx series high strength alloys for this process normally require a solution treatment, which is problematic for large near-net-shape components, and age hardening to achieve maximum mechanical properties. With each layer being subject to multiple thermal cycles, exploiting the thermal conditions in the WAAM process to avoid post-build solution treatment is therefore of interest. A solutionisation model has been developed for the WAAM process, based on diffusion controlled dissolution using DICTRA, which was validated through thermal simulations combined with 2D and 3D image analysis. The model has subsequently been used to simulate the solutionisation behavior during a typical WAAM thermal cycle and to explore what could theoretically be achieved by, for example, refining the starting microstructure.INTRODUCTION There is currently great interest in exploiting additive manufacturing (AM) in the aerospace sector due to several benefits it can potentially provide; including reduced material waste, shorter product lead times and greater design freedom (Herzog, Seyda, Wycisk, & Emmelmann, 2016). However, with aluminium alloys the material properties obtained are generally inferior to those of conventional high-strength wrought products; therefore more research is required to explore the potential for exploiting the unique process conditions in AM to improve the as-deposited microstructure. A range of AM techniques are now available (Debroy et al., 2018), which differ in terms of the feedstock type and power source and it is necessary to match the appropriate technology to a particular application. This generally requires a compromise between the build rate and shape resolution. Wire and plasma-arc additive manufacturing involves using an electric arc to melt wire onto a substrate, and fabricates a part by building up overlapping layers of deposited weld beads (Addison et al., 2015; Williams et al., 2015). The benefits of this process over other AM methods are the much higher deposition rates (e.g. kg’s/hour) achievable and lower capital equipment costs relative to powder bed techniques, which makes it suitable for large scale applications. However, limitations include a lower part complexity, lower solidification rates and a greater need for post-process machining (Frazier, 2014)."

Jan 1, 2018

"Conveyed coal flows have been diverted on the basis of real time ash analysis since the 1980s. Many coarse particle separation methods are available through screens, jigs, heavy media separation, particle sorters, to name a few, however bulk diversion requires a representative, continuous analysis to ensure diversion decisions can be made with confidence. Sensors also need to be able to provide measurements at useful time increments so that small tonnages can be diverted for maximum selectivity. Particle separation typically requires high capital costs and there are limitations either in throughput tonnage or particle size or both. Few techniques are able to provide robust and representative analysis of conveyed flows in a useful time basis. Prompt Gamma Neutron Activation Analysis provides multi-elemental analysis of conveyed bulk materials and has been proven in the minerals industry since 2003. This paper outlines the success of this technology in minerals applications in iron ore, phosphate rock and most recently in copper-gold ores, including its use in bulk diversion.INTRODUCTION Naturally occurring quality variability, or heterogeneity, in mineral deposits enables separation and recovery of the valuable components through mining and processing operations. There are distinct advantages in processing the minimum quantity of material to achieve the highest possible yield. Unfortunately, declining ore grades has resulted in larger scale operations and a subsequent loss in selectivity for mining operations. As limits are approached on the practical size of equipment, there is more motivation to investigate alternative solutions. Mining companies are subject to increasing social resistance to growing waste disposal requirements in addition to higher energy and transport costs. Major savings are available by reducing the quantities of material processed where pre-concentration can be effectively applied at early stages in the process. One of the simplest ways to pre-concentrate is to measure the bulk material and reject waste soon after mining so that minimal expense is incurred and that only higher quality material is sent to processing operations. This bulk sorting can occur within the mining operations and has major benefits through energy and other consumables savings. This paper discusses the application of real time analysis technologies suitable for bulk sorting within the minerals industry. Technology that has proven representative for conveyed material bulk analysis and its successful applications to date is explained. Analysis using a sensing technique is only one component of a successful bulk sorting process; the importance of effective diversion systems and a bulk sorting strategy are also discussed. The bulk sorting stage may be one component of a system that could include additional downstream technologies such as particle based sorting systems on a diverted stream."

Jan 1, 2018

By W. Lodge, G. Rasmussen

"The carbon-in-pulp (CIP) process has been the dominant gold recovery technology since the 1980s. During all this time carbon measurement, and control of the carbon transfer pumps has been largely manual in nature. Such manual operation inevitably limits process efficiency, potentially resulting in higher gold solution losses, and higher cost of circuit operation. Based on the authors’ experience, average plant solution loss is in the range of 0.02-0.03 ppm Au, as opposed to the general industry target of 0.01 ppm Au or less. Gekko Systems, in conjunction with Curtin University’s Gold Technology Group, has developed a carbon concentration meter, the ‘Carbon Scout’ meter. The meter automatically measures carbon concentration in all tanks, providing more frequent and more precise data. Combined with SIMCIL, a CIP circuit process model which is used to determine the optimum set points for the circuit, the meter should ensure lower gold solution losses, and more efficient operation of the carbon circuit. This paper will review they critical factors for good carbon management, the development of the meter and results from the first plant installation. Additional benefits of the Carbon Scout, including improved health and safety and the opportunity to measure other key variables in the leach/adsorption circuit from one central location will also be described.INTRODUCTION The carbon-in-pulp (CIP) process was first introduced to the gold industry in the early 1950s at the Carlton Mill in the USA (Fast, 1988), with the modern version of CIP becoming fully developed with large scale installations in South Africa in the late 1970s (Laxen, 1982). CIP quickly became the technology of choice for new operations, and for the retrofitting or upgrading of existing operations. In the 1980s the carbon-in-leach (CIL) circuit configuration became the process design of choice due mainly to its lower capital costs. With 40 years of operational experience, CIP/CIL for gold recovery is now mature a technology, whose operations and limitations are well understood. To extract further efficiencies from such technologies, by improving recoveries and/or reducing operating costs, is challenging and may require new approaches to circuit management. Gekko Systems, in association with the Gold Technology Group at Curtin University, has developed the Carbon Scout, an automated carbon measurement device. This device replaces manual measurement of carbon concentration in carbon adsorption tanks, providing more frequent and more accurate data for control of the CIP process. Data from the Carbon Scout can be used to automatically control the carbon forwarding pumps."

Jan 1, 2018

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By C. Tong, B. Hilscher

"Sensor based ore sorting is being rapidly adopted by the mining industry. The ability to boost mill feed grade by rejecting waste grade rocks early in the process has proven revolutionary for some operations.This paper briefly reviews the current position of ore sorting in the industry, as well as abridged results from specific operations such as Barrick, McEwen, New Gold, and two others. The paper also introduces the concept of “Profit Recovery™”, the measuring of recovery based on rock profitability rather than just metal content.IntroductionSensor based ore sorting is being rapidly adopted by the mining industry. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes have been too invaluable to be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. In addition, the advent of ore sorting has also called for a new standard of recovery analysis. The answer to this is the creation of a new term and concept - Profit Recovery™.This paper evaluates the most recent results of ore sorting in the mining industry, and presents the results from five different mining operations. Additionally, this paper will discuss and evaluate the Profit Recovery™ of each of these operations. The goal of this paper is to address common concerns regarding ore sorting rejects and their actual impact on project economics.State Of The ArtOre Sorting is a sensor-based sorting and pre-concentration technology implemented before the processing stage that is used to reduce the amount of waste reporting to the mill feed. This technology can also be utilized to recover ore from previously uneconomic waste, as well as reduce the mill energy and reagent consumption (Tong, 2012). In greenfield projects, sensor-based sorting can further provide value by reducing processing capital costs. The decline of available high grade orebodies and decreasing head grades has further increased the attractiveness of pre-concentration, and subsequently ore sorting (Lessard et al., 2014).There are currently two notable types of sensor-based sorting: bulk and rock-by-rock. Bulk sorting consists of live, high tonnage sorting that can be installed on a scoop or on a conveyor belt with a diverter. Rock-by-rock is a selective sorting method that scans and sorts individual rocks on a conveyor belt, and rejects rocks using air jets or mechanical levers. Figure 1 shows a diagram for a typical air jet sorter."

Jan 1, 2018

By Z. Zhang, X. -G. Chen, F. Breton, A. Arici

"The microstructure of Al-10Si-0.3Mg-0.5Mn alloy with 0.27% Zr and 0.19% V addition was quantitatively analysed and compared to the base material. The addition of Zr and V in the AlSi10Mg alloy exhibit a beneficial effect on the Si modification, resulting in the reduction of the size of eutectic Si particles on both as-cast and T6 conditions. The quantitative image analysis results show that the Zr and V addition and T6 treatment can reduce the size of the intermetallic phases. In addition, the presence of Zr and V is favour to the partial dissolution of the intermetallic phases during the T6 treatment. Different heat treatment procedures were tested to optimize treatment parameters. The mechanical properties of the alloys were evaluated using hardness measurements and tensile tests. The results show that the addition of Zr and V can remarkably improve the mechanical properties on as-cast and T6-treated conditions. The correlation between the microstructure and mechanical properties of the alloys is discussed.INTRODUCTION Al-Si-Mg foundry alloys have been widely used in automotive and aerospace industries due to their high strength-to-weight ratio, heat-treatable capability and excellent castability. The alloying elements such as Cu, Mn, Fe are traditionally added into Al-Si-Mg alloys to improve their mechanical properties (Mohamed, Samuel, Samuel & Doty, 2009). In recent years, the attention has been paid to the effect of the transition elements such as Zr, V, Ti, etc, as minor alloying additives, on the properties of aluminum alloys (Elhadari, Patel, Chen, & Kasprzak, 2011; Kasprzak, Amirkhiz & Niewczas, 2014; Shaha, Czerwinski, Kasprzak, Friedman & Chen, 2015; Shaha, Czerwinski, Kasprzak & Chen, 2014; Mahmudi, Sepehrband, Ghasemi & 2006; Meng, Cui, Zhao & Zuo, 2013). Kasprzak et al., (2014) and Shaha et al., (2015) reported that additions of Zr, V, and Ti in Al-Si-Cu-Mg cast alloys can improve the alloy mechanical properties at high temperature by forming stable intermetallics and precipitates on as-cast and heat treatment conditions. On the other hand, the mechanical properties of near-eutectic and eutectic Al–Si cast alloys depend not only on the chemical composition but also, even more importantly, on microstructural features such as the morphology and size of eutectic silicon and intermetallic particles, which are present on both as-cast and heat treatment conditions (Mohamed et al., 2009). However, there is rather limited information on the effect of Zr and V on the microstructure features and mechanical properties of near-eutectic Al-Si-Mg cast alloys."

Jan 1, 2018

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By N. O. Lotter

The connection between mineralogy and metallurgical performance in a plant was recognised long ago (Gaudin, 1939; Petruk, 1976; Petruk and Hughson, 1977; Cabri, 1981; Petruk and Schnaar, 1981; Kinloch, 1982; Peyerl, 1983, Baum et al 1989 for example). The modern toolbox that we now routinely use for flowsheet development took decades to develop (Lotter et al., 2002; Baum and Lotter, 2004; Lotter, 2011 for example). Many workers contributed considerable time and effort to this overall mission of connecting sampling, mineralogy and mineral processing to integrate the flowsheet development activities. Certain key milestones marked this journey, such as Gy’s treatise on the sampling of particulate materials in 1979, which was later added to by François-Bongarçon, Pitard, Minnitt, and Holmes for example. The development of QEM*SEM by Gottlieb et al. of the MLA by Gu et al. constituted a huge leap forward in accuracy and mineral measurement capacity, as well as a reduction in standard errors of mineral characterisation. The advancement of the microprobe to an automated platform made a significant difference to detailed compositional mineralogy. This led to a strong position from which to draw meaningful processing implications from the mineralogical data. Reproducible flotation testing and reliable plant survey material for characterisation was dealt with by, amongst others, High Confidence Flotation Testing ( Lotter, 1995: Runge, 2010, and Bradshaw, 1997); and Statistical Benchmark Surveying (Lotter, 2005), with earlier prototypes which were steadily improved (Lotter, 1994; Restarick, 1976). The sterling work of Napier-Munn in engaging sound statistical methods with mineral processing led to the successful design and use of methods that could identify and quantify small recovery gains in plant scale trials. This history and present capability are reviewed, including leverage into asset management.

Jan 1, 2018

By F. Bélanger, P. A. Fournier

"Modelling and optimization techniques used in the operation of the Detour Lake Mine leach circuit are contrasted to a 1973 review of contemporary techniques used by a major gold producer. The leach circuit at the Detour Lake Mine was modelled using a full factorial Design of Experiment of stirred tank reactor leach tests using circuit feed. Contour plots of extraction were applied in the plant to optimize addition rates of cyanide and the newly-commissioned lead nitrate system. Contour plot sections were used to understand the impact of sulphur in circuit feed at different operating dissolved oxygen concentrations. The 1973 review paper offers insight into industrially-applied modelling and optimization techniques. In particular, a mathematical model of plant data was developed using multilinear stepwise regression analysis. The model was presented using graphical representations available at the time and applied to optimize the rates of cyanide addition. Off-the-shelf software solutions of today allow mineral processors to quickly and easily visualize data, allowing them to re-allocate time and resources spent processing data to generating raw data and extracting actionable information.IntroductionModelling and optimization in mineral processing is the art of reducing reality through judicious use of assumptions to understand a process and leverage this knowledge to engineer practical solutions to metallurgical problems. Data analysis is at the core of this enterprise.While this paper showcases the modelling work done at the Detour Lake Mine (DLM), the primary objective is to pause and reflect on how far the field has progressed since the 1970’s. A snapshot of state-of-the-art gold cyanidation modelling at that time is a review paper of the Anglo American Group’s capabilities (Brittan & van Vuuren, 1973). The objective of this paper is not a play-by-play of the evolution of modelling and optimization since that time. Rather, it is a comparison of the field at two points in time.In 2016, DLM undertook an extensive bench-scale leach circuit modelling program to better understand the impact of cyanide, dissolved oxygen, lead nitrate, grind size, density, and pH on gold cyanidation (Fournier, 2016). Two major capital expenditure projects were anticipated for 2017: improvements to oxygen control and a lead nitrate distribution system. While the lead nitrate system was planned for construction, the design parameters had not yet been selected. Following the development of the model, plant trials were executed to validate aspects of the model and the methodology was expanded to address other plant issues, in particular the effect of talc chlorite and pyrrhotite in leach feed.The variables of the bench-scale study are summarized in Table 1. Dependent variables were varied using a full factorial design of experiment with two repetitions for each test condition, yielding a total of 300 tests. Test order was randomized to eliminate bias from independent variables."

Jan 1, 2018

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By A. Yaghini, Y. Pourrahimian

"Human factors (HFs) play an important role in the mining and mineral industry, affecting operational and maintenance efficiency and safety. Despite the introduction of new technologies and automation in this sector, it is well known that a significantly large proportion of total human errors occur during the operation and maintenance phase. A comprehensive literature review of HFs across several industries is provided. From this review, the impact of HFs on operation and maintenance is summarized, with a focus on what the mining industry is currently doing and what opportunities exist for additional improvements. Future research directions and themes are also identified.RÉSUMÉ Les facteurs humains (FH) jouent un rôle important dans l’industrie des mines et des minéraux, en ce qu’ils affectent l’efficacité et la sécurité de l’exploitation et de l’entretien. Malgré l’apparition de nouvelles technologies et de l’automatisation dans ce secteur, il est bien connu qu’une grande partie des erreurs humaines (EH) se produisent durant une phase d’exploitation et d’entretien. Cet article propose une analyse documentaire approfondie des FH dans plusieurs secteurs. L’impact des FH sur l’exploitation et l’entretien est résumé à partir de cette analyse, une attention particulière étant accordée à l’évolution de l’industrie minière et aux possibilités d’améliorer davantage ses activités. Sont également identifiés les futurs thèmes et voies de recherche.INTRODUCTIONDuring the past several decades, the mining industry has focused on improving equipment, machinery, and methods that have led to more advanced hardware and software, equipment with higher reliability and productivity, and other technological advancements. These actions have improved safety and productivity and have reduced casualties and maintenance workload. Although today’s mining equipment and machinery are technologically advanced and highly reliable, the risk of accidents is still relatively high and key performance indicators have not improved significantly compared to other industries (Sorensen, 2012). A prominent reason could be due to insignificant integration of human factors (HFs) as part of planning, operation, and maintenance activities. The current mining system is a people system, and inevitably HFs and human error (HE) figure prominently in all aspects of this industry. Even the most advanced technologies and innovations require operators and maintainers with significant knowledge and skill, which could increase the potential for HE."

Jan 1, 2018