Search Documents

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By Bian Xue, Wu Wenyuan

High quality, mono-dispersed, hollow CeO2 microspheres with high surface area were produced by a spray pyrolysis method at 700oC. CeCl3 was used as the raw material of the process rather than Ce(NO3)3 because the latter is relatively difficult to obtain in industrial quantities. X-ray diffraction and electron microscopy results confirm the high quality synthesis of hollow CeO2 microspheres with narrow size distribution, good mono-disperse, and good reproducibility. The process of the formation of mono-dispersive CeO2 microspheres was investigated by chemical dynamics and a possible mechanism is proposed. This simple method for synthesis of CeO2 microspheres is easily scaled up to fabricate other metal oxide nanostructured materials at industrial scale.

Jan 1, 2014

By L. Li

ABSTRACT Stope backfilling is a common operation in many underground mines, which requires a barricade at the base of the stope near the drift entrance to retain the backfill in place. In this paper, the distribution of pore-water pressure in barricades made of waste rock is analyzed. An analytical solution is introduced and applied to estimate the pore-water pressure along the base and full height of the barricade. Results show that the analytical solution generally accurately predicts the distribution of pore-water pressure obtained from the numerical calculations, especially in the upstream part of the barricade, where it is most critical.

Jan 1, 2013

By G. Q. Zhou, H. C. Liang, X. D. Zhao

"This study describes the strain behavior in vertical shaft lining (VSL) embedded in thick soil deposits and its application in assessment of concrete deterioration. The observed strain in VSL continuously decreased companied by a sinusoidal fluctuation due to the influences derived from negative skin friction (NSF) and temperature. The increase in strain increment between peak and trough at each year and compressive strain level as the servicing time continued and VSL depth increased implies that the concrete strength was attenuated, and this attenuation was significantly dependent on the existing compressive strain level in VSL. The reliability of the proposed approach was validated by Schmidt Hammer Technique (SHT) – based concrete strength, and is applicable in concrete assessment and then fracturing prediction of VLSs in thick soil deposits.Concrete strength, Field monitoring, Strain behavior, Vertical shaft liningINTRODUCTIONOver 100 VSLs in Southeastern China subjected to an unpredictable fracturing as shown in Figure1, and there are over 1,000 VSLs embedded in thick alluvium su?ering from challenges of damaging and potential fracturing (Cheng, Yang, Zhou, Li, & Hu, 1993; Zhou, Cui, Lv, Huang, & Chen, 1999; Li & Li,2005). Therefore, a reliable assessment of these VSLs is significant to the normal servicing of mine shafts and the recycle of underground space when these mine shafts were closed.The continuous increasing of NSF induced by the drainage of water–saturated deposits well interpreted such extensive fracturing phenomenon, and it is universally regarded as the governing indicator to determine the VSL stabilization (Cheng et al., 1993; Zhou et al., 1999). Based on this recognition, the fracturing prediction and VSL strengthening according to the field monitoring on hydrogeological characteristics, servicing environments, and mechanical behaviors of VSL were carried out (Zhao, Zhou, Zhong, Zhu, & Liang, 2009; Liang et al., 2009; Xie, Lv, & Wu, 2014). As known, the compressive strain level in VSL and the in–situ strength of VSL concrete were the main factors to perform such fracturing prediction. However, the existing studies in literatures were limited to the strain accumulating or releasing behaviors (Zhao, Zhou, Zhao, Kuang, & Hu, 2017), and lack of considering the VSL concrete strength and its attenuation. In this reported study, the in–situ monitoring data on the strain in typical VSLs and the VSL elevations between 2004 and 2014 were initially analyzed. Then, an observed strain behaviors–based approach was developed to quantitatively evaluate the VSL concrete deterioration."

Jan 1, 2019

By Edgar Dernedde

Cryolitic melts at a temperature of about 960 °C are used in reduction cells to dissolve alumina and to produce primary aluminium. At these temperatures cryolitic melts with an acidic composition have a significant vapour pressure, which contributes substantially to the evolution of fluorides from these cells, The Antoine equation is commonly used for relating vapour pressure data of liquids at different temperatures, It is also applicable to cryolitic melts, Published equations have at least 20 numerical constants, in order to allow for the effects of melt composition. In the present work a simplified equation with only 12 numerical constants was developed and is applicable for multiple additions to molten cryolite up to 30 wt %, The simplified equation was compared with the published equations of Haupin & Kvande and Gustaysen & Ostvold using 472 vapour pressure data of cryolitic melts. Results showed that the simplified equation has the same accuracy as the published equations in the composition range of interest to industry.

Jan 1, 2004

By R. B. Roberts, A. L. Mular

A simple way to determine the IEP of oxide minerals is described. The method is shown to apply for fine powders of Fe203 and ZnO. The IEP lies at pH 6.95 for Fe203 and at pH 9.08 for ZnO.

Jan 1, 1966

By Yasser Mohamed

Daily field management of earthmoving operations requires quick and regular decisions for allocating available equipment to different jobs on a project. A general foreman?s day starts with matching several activities with a suitable set of available equipment to achieve the highest productivity and lowest unit cost. Usually, this decision-making process needs to be quick, and depends to a great extent on the foreman?s experience, which varies from one individual to another. Many analytical solutions with various degrees of sophistication and optimization exist to address such decisions. However, adopting any of these solutions is contingent on how accessible and easy-to-use the solution is. This paper discusses the development process of a webaccessible solution for evaluating earthmoving fleet composition and allocation scenarios. The solution relies on discrete event simulation and an optimization backend engine, but introduces the user with a simplified and easy-to-use interface that is accessible from any mobile device, and is customized to specific user?s needs. The developed system gathers most equipment and site-related input data from a company?s information systems to minimize user input. The user mainly needs to formulate equipment and job combinations and allocation scenarios (e.g. soil type, quantity, and hauling distance), according to equipment availability each day. Then the system will evaluate the productivity and unit cost estimates for each scenario, allowing the user to choose the most suitable one. It may also be used to automatically recommend the optimum solution given an available list of equipment. The paper presents the process followed in prototyping the proposed system in collaboration with a major Canadian earthmoving contractor, and customizing it to the user needs within the company. It also describes the overall structure of the developed system and its core simulation model.

Aug 1, 2013

By Ernest Baafi

A simulation model RoadSIM using the ARENA modelling system has been developed to evaluate roadway development options for a given development panel configuration. The RoadSIM simulation system has provisions for variability/randomness in operations including cutting and loading at the face, tramming and discharge of coal to the boot end and availability of equipment. The modelling system provides a means for assessing the operational limitations of roadway development practices at a particular coalmine. It is a ?what if? tool that allows a range of equipment, configurations and operating practices to be assessed in terms of achievable advance rates and equipment utilisation. Output from the system is in the form of a dynamic visualisation as well as summary reports and detailed logs of operations over time.

Oct 1, 2009

By N. P. Hristov, L. V. Kuzev

"A simulation study of the fill factor of a drum mill was conducted using two types of grinding media: balls and tetraballpebs. Each medium was composed of equal number of grinding bodies having equal weight but different shape. The difference was in the density of the two grinding media.Standard spherical grinding bodies (balls), which were used in practice, and equivalent (by weight) grinding bodies in the shape of spheroidal tetrahedrons (tetraballpebs) were studied. The simulation was conducted in a module of a 1.2 m diameter drum mill, whose length exceeded twice the diameter of the corresponding grinding body. The grinding balls had a few percent (3 to 6) higher fill factor than the grinding tetraballpebs in the same shell.Vertical sections of the grinding medium were taken across the studied shell module along its axis. They showed the location of each grinding body in the fill volume. Defects in the packing of the grinding bodies and the contacts between them and with the inner surface of the shell were also show. Differences in the contact points of the balls and the tetraballpebs were noted. For the tetraballpebs, we observed contacts both between the spherical surfaces and with the edges and vertices of the grinding bodies.The topography of the grinding media is shown visually.INTRODUCTIONThe grinding balls have been studied extensively. It is the traditional grinding medium in ore processing industry. The parameter characterising the grinding medium is its density. It is the mass of the grinding medium per unit of volume. The parameter may have a range of values. It depends on:• The physical properties of the material they are made of;• The shape of the grinding body;• The dimensions of the body;• Size distribution of the grinding bodies in the grinding media.In comminution, the fill factor of the mill shell is the process parameter that is representative of the grinding medium. Some publications have indicated the disadvantages of ball grinding. For example, Wu, Xiang, Glen, and Duan (2008) note in the analysis of the mechanism of grinding that the balls are not the best grinding media and disadvantages include among others:• Easy over-grinding resulting from the point contact between the balls;• Attrition surface is the smallest in the grinding media;• Poor selective exposure of minerals resulting from the accidental and often significantly more powerful impact on the feed;• The grinding efficiency drops as the fineness of grind is increased;In the Handbook of mineral processing, Polkin (1950) noted that the shape of the grinding bodies determines the volume of the void spaces therein and therefore the shape affects the grinding efficiency per unit of volume of the grinding medium."

Jan 1, 2016

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By G. Vibert Douglas

It often happens that the field geologist encounters a fault in ground where there is little to guide him with regard to the throw, or vertical displacement, and the heave, or horizontal displacement. The following construction gives both of these components of the fault, and the writers hope that it may prove a help to others. The construction is applicable to both normal and reversed faults. Briefly the procedure is as follows: Take a point which is common to the faulted geological feature and to the fault plane and on the downthrow side of the fault. Move this point in the horizontal plane in the direction indicated by the fault striæ. Rebat the point down to the plane of the fault and obtain its throw. Next consider the other side of the fault and truncate it down by the amount of the throw just determined. Then project the line of the geological feature through to the trace of the fault-plane at the lower horizon. The result is the relative positions of the two parts of the original geological feature as severed by the fault. In Figure r, let us consider a typical normal fault, that is, a fault in which the hanging-wall has gone down relative to the footwall. This characteristic, or its alternative, the reversed fault, is determined by observation on the ground. Let AB be the line of any geological feature such as the edge of a dyke, vein, or bedded sediment. The plane of which AB is the trace may have any dip; in the present case let us say 70° right. Let FF be the trace of a fault-plane which may have any dip; let us say 35° left in this case.

Jan 1, 1928

By S. V. Burr

"IntroductionOne of the more puzzling geological enigmas, in the writer's opinion, is how rock can move sideways with respect to other rock. In the writer's study of regional northwest-southeast folding in North America (Burr, 1980), he may have found the answer to horizontal offset.Horizontal OffsetSideways movement or horizontal offset does not mean that the movement was, or is, horizontal. As indicated below, the actual movement may be at a high angle from the horizontal. However, it is the horizontal VECTOR, or offset, which is measured on surface by geologists. Vertical movements (thrust, normal, reverse) can be understood, as they involve blocks of rock , generally separated on four to six sides, which have been pushed up or subsided. Vertical faulting across dipping strata can produce APPARENT horizontal offsets. However, this thesis deals only with ACTUAL offsets.The ProblemFigure 1 is a plan view of a simple hypothetical horizontal offset. Three vertical dykes are intersected by a fault lineament. Two dykes exhibit no movement; the middle dyke has been offset a distance (a). Vertical faulting would have produced no horizontal offset. How can a horizontal distance (a) disappear or appear? Rock expands or contracts in infinitesimal amounts.SolutionThe map (Burr, 1980) shows the writer's interpretation of regional northwest-trending folds in Ontario. The writer made two observations about horizontal offsets during his thirty year study of these folds:1) All major horizontal fault lineaments strike at a high angle to the northwest fold axes. Many of the northwest-trending lineaments are fault s, but their movement is essentially vertical.2) Close to many of the known horizontal offsets (and several lineaments), there are areas where plunge reversals are so frequent and close together it is impossible to draw in all the fold axes at a scale of 1 inch = 4 miles, and, in the highly faulted Espanola area southwest of Sudbury, Ontario, all the indicated folds cannot be easily separated at a scale of 1 inch = 1 mile. The writer has observed folds less than 30 feet apart next to the strong Puskitamica-Chibougamau fault in northern Quebec."

Jan 1, 1982

By A Frostick

Ranger uranium mine is surrounded by the World Heritage listed Kakadu National Park and offsite impacts resulting from mining at Ranger would affect the Magela Creek catchment first. Radionuclides, lead isotope ratios and metal concentrations were measured in sediment cores from the Magela Creek catchment around Ranger to investigate the dispersion of mine-derived particulates. The study found a localised area within the Ranger mineral lease, where upper sediments had elevated levels of radionuclides and trace metals and radiogenic Pb isotope ratios. There is no current evidence of sediment dispersion from Ranger further downstream within the Magela Creek catchment.

Aug 1, 2010

By E. Stansfield

Coal samples are sometimes taken from a wet spot in a mine, or from an open car or pile shortly after rain, and submitted for analysis in a dripping wet condition. Other samples are taken from a dry spot in the mine, or from an open car or pile after a period of dry weather. Comparison of the analyses obtained in the two cases would be absurd, although the samples might be of essentially the same coat apart from the surface moisture on the one. The analyst therefore attempts to reduce all samples to an equal basis by the operation known as air-drying. Air-drying is practised by the chemist for three reasons: (1) To make it possible to grind the coal to powder. (2) To bring the coal sample to a condition in which it will not change in weight rapidly whilst portions are being weighed out for analysis -in other words, to bring it into equilibrium with the air in the laboratory. (3) To determine the water-retaining power of the coal. Any kind of drying is satisfactory for (1); the coal should be dried more or less according to the humidity at the time in the laboratory for (2); whilst it should be always dried to the same extent for (3). In other words, no method can be satisfactory for both (2) and (3). In this paper the only question considered is (3) -that is, air-drying the coal under standard conditions so that strictly comparable results can be obtained for the water content of coals after air-drying. After a sample of wet coal is exposed, it loses moisture until it is in equilibrium with the air at the time: thus the coal will loose distinctly more water in air of 20 per cent relative humidity, for example, than it would in air of 80 per cent.

Jan 1, 1923

By Peter Cunningham

General Description of Projects The objective is to streamline data transfer within our Process Control and Business Systems for the purposes of tracking actual production, reducing manual record keeping, improving process control and improving vehicle maintenance. This presentation focuses on two implementations of mobile equipment data acquisition systems which make use of industry standard data models and data transport protocols. Pilots are part of the Mines Technology Roadmap to improve our mining operations ?Enabling technologies and pilot of key systems

May 1, 2013

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

By W. L. Goodwin

Twenty-five years ago mining engineering in Canada was not a profession. To-day the members of the mining fraternity can fairly claim for 10themselves the professional status. If their pretension is not fully warranted by fact it is not for lack of any technical attainment or service to the public but by reason merely of their neglect to cultivate the cohesion and consciousness that are the outward and visible signs of a professional body. This paper is an attempt, first to sketch briefly the course of the events during the past thirty-five years that have resulted in organizing the mining industry of this country in its present form; then to notice the principal features of the professional organization of this day; and finally to point out that an important part of the work of the mining engineer remains in the state of chaos that characterized the whole of it three or four decades ago, and to suggest a remedy. Thirty years ago there came a great wave of interest in mining in Canada, based principally upon the discovery of gold-quartz and gold-copper throughout wide areas in Nova Scotia, Ontario and British Columbia.

Jan 1, 1926

By J. E. Tupper

"This paper will discuss strategies for the introduction of computer technology in the mine environment. More specifically, it will focus on issues such as: (a) make or buy; (b) programmer less mines; and (c) support from corporate groups.The paper relates these strategies to systems for mine operations. These will be illustrated by considering the implementation of some phases of these systems at Teck Corporation.IntroductionThis presentation addresses some of the major considerations in a strategy for mine computerization and then relates these considerations to the computerization cycle and Teck Corporation.Strategy is defined as a conceptual framework or plan to accomplish a goal. For purposes of this paper, the goals can be more simply defined for operational purposes as either increasing revenue or decreasing costs.The strategy will allow us the framework for measuring tactical decisions such as computer and software acquisitions.The Mine Life CycleTo start with, let us look at the mine life cycle from a computer systems point of view:-Exploration-Property Development-Feasibility-Construction-OperationFrom a systems point of view, the exploration cycle is oriented to geophysical and geochemical computing. Property development starts with drilling and building the geological data base. The feasibility cycle includes all stages of evaluating the decision to proceed with mine development: ore reserve calculations; mine planning; and financial projections. Construction includes project management and project accounting systems. Systems required for operation are those needed by personnel at the mine site."

Jan 1, 1982

By A. Hutwalker, T. Plett

"Blast fumes are one of the major sources for NOx in underground mines. In 2016, the Occupational Exposure Limits for NOx in Germany were reduced by 90%. The task is to keep re-entry times after blasting at the present level and thereby ensure an economic operation of the mine. Measurements show that using ventilation solely is not sufficient. A new approach to reduce NOx from blast fumes is described. Laboratory experiments were performed and a reduction of NOx was observed. Measurements were conducted at an explosive factory’s testing facility and in an underground mine at blasting operations. INTRODUCTION Whether for production of ore or for drift development, the processes in an underground mine are always the same: 1) fracturing the rock, 2) loading the pile, 3) support the resulting cavity. The fracturing of the rock can be done mechanically, by cutting, for example by using continuous miners or tunnel boring machines, or by drilling and blasting. Drilling and blasting is more flexible than mechanical driving, as it can be used independently of the rock strength. Furthermore, this driving method allows a more flexible reaction to changes in geological and/or operational conditions. Thus, underground mining and blasting are almost inextricably linked with each other, and regardless of the size and level of technology of the mine, blasting is hardly avoidable. Depending on the mining method chosen and the existing framework conditions, such as the mechanical properties of the rock or the availability of machinery, blasting is an integral part of daily operations. Even in mines where blasting is not part of regular operations, it cannot be completely avoided. The blast fumes generated by the explosions are, in addition to diesel engine emissions, one of the two main sources of emissions of nitrous gases underground. Up to now, state of the art for dealing with blast fumes is ventilation. The fumes are diluted with fresh air and ventilated out of the mine. This treatment of blast fumes is more than sufficient with the former German Occupational Exposure Limits (OEL). The adaption of the OEL in Germany to the recommendations of the Committee on Occupational Exposure Limits (SCOEL), a committee of the European Commission, leads to big challenges for the mining industry in reducing the concentrations of these gases at the workplaces underground. On its meeting on May 2nd and 3rd 2016, the Committee on Hazardous Substances (Ausschuss für Gefahrstoffe, AGS), an advisory body of the German Federal Ministry of Labour and Social Affairs (BMAS), advised the BMAS to copy the OEL, as recommended by the SCOEL, to the Technical Rules for Hazardous Substances (TRGS 900). BMAS followed this advice, consequently the new OEL where published on November 4th 2016 and became part of the TRGS 900. Table 1 shows the former and new OEL for Germany. These new OEL became law after publishing, but two exceptions were made: For tunneling operations, they became law on October 31st 2017, for mining operations they will become law on October 31st 2021 (BAuA, 2004, 2016, 2017)."

Jan 1, 2019