Search Documents

By Graham Bright

The rapid increase in reliability, the low cost of operation, the ready application of safety devices, and the growing availability of central-station power have made the question of installing a hoist of the electric type no longer debatable. Where adequate electric power is available, there are few cases where it would be advisable to install a steam or air hoist. The type of electrical equipment depends largely on the nature of the power supply, its capacity, and the form of the power contract under which power is purchased. In a large majority of cases, the available electric power is alternating current, three phase, 60 cycles. There is, however, considerable 25-cycle power in use; and in a few instances constant voltage direct current is the only power available for a small or an occasional medium-size hoist. Where a new hoist is to be installed, the designer of the mechanical parts can readily take care of the maximum stresses likely to be imposed by the motor. Where the hoist is already installed and operated by steam or air and it is desired to substitute an electric motor for the engine, a careful check should be made to determine the advisability of using the old mechanical parts. In most cases it is better to install a complete new hoist than to attempt to use old mechanical parts. A steam engine has a definite maximum torque, which the hoist has been designed to withstand, while a motor may be able to deliver momentary torques beyond the strength of the mechanical parts of the hoist. The selection of the proper type of electrical equipment can only be made after complete information is obtained and certain calculations made to determine the capacities required. There are several methods used in making hoist calculations, but no matter what method is utilized a fair degree of familiarity with hoists and hoisting conditions is necessary before an intelligent analysis and proper selection can be made. Forms Used in Hoisting Calculations Some of the hoist calculation methods are long and complicated. Where such calculations are seldom made, it is better to use the

Jan 1, 1922

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By William E. Ford, Edward Salisbury Dana

239, Contact-Gwiorneters. - The interfacial angles of crystals are measured by means of instruments which are called goniometers. The simplest form is the contact- or hand-goniometer one form of which is represented in Fig. 377. This contact-goniometer consists of a card on which is printed a semi- circular arc graduated to half degrees at the center of which is fastened a celluloid arm which may be turned to any desired position. The method of use of the goniometer is illustrated in Fig. 377. The bottom of the card and

Jan 1, 1922

By William E. Ford, Edward Salisbury Dana

Examination in the Wet Way Examination by Means of the Blowpipe 479. The complete investigation of the chemical composition of a .mineral includes, first, the identification of the elements present by qualitative analysis, and, second, the determination of the relative amounts of each by quantitative analysis, from which last the formula can be calculated. Both processes carried out in full call for the equipment of a chemical laboratory. An approximate qualitative analysis, however, can, in many cases, be made quickly and simply with .few conveniences. The methods employed involve either (a) the use of acids or other reagents " in the wet way," or (b) the use

Jan 1, 1922

By George Watkin Evans

During the past ten or twelve years, the average reader of newspaper and magazine articles has been led to believe that enormous deposits of high-grade coal exist in the northland and that these can be mined for practically nothing. But much of the reputed glitter and attractiveness of Alaskan coals disappears when viewed at close range. Many areas of coal-bearing rocks are widely distributed geographically from Cape Lisburne, on Bering Sea, to Admiralty Island, south of Juneau. Bituminous coal is found at Cape Lisburne, on the Bering Sea, at Five Finger Rapids on the upper Yukon, and at Herendeen Bay and Chignik Bay; lignite is found on the Kobuck River, along the Yukon River from points near the mouth to Tonakat, near Rampart, at Dawson, on the east shore of Cook Inlet, and in the Tanana Valley, 50 mi. south of Nenana. The Susitna and Matanuska Valleys contain coal ranging from lignite to anthracite, and in the Bering Lake district, there are coals ranging from semi-bituminous to anthracite. No effort will be made to describe all of these fields, but the writer will confine himself to the four principal fields, namely, the Nenana field! in the interior of Alaska, tributary to the Fairbanks district; the Matanuska field, in the Matanuska Valley; the Kachemak Bay field on the east shore of Cook Inlet; and the Bering River field, east of the mouth of Copper River. Nenana Coal Field The Nenana field occupies an area east of the Nenana River 70 mi. (112 km.) southwest of Fairbanks and approximately 50 mi, from the town of Nenana, which is located at the junction of the Alaskan Railway and the Tanana River. It is on the northern flank of the Alaskan Range and occurs within the foothills of that district. The elevations range from 1000 to 4000 ft. (304 to 1219 m.). Future developments may prove the field to extend from a considerable distance west of the Nenana River to the headwaters of the Tanana River. The coal measures are of Tertiary age and are probably Eocene. They are not badly deformed by folding, but portions of the field show

Jan 1, 1922

Jan 1, 1922

By William E. Ford, Edward Salisbury Dana

IN the representation of crystals by figures it is customary to draw their edges as if they were projected upon some definite plane. Two sorts of projection are use8; the ah- graphic in which the lines of projection fell at right angles and the chirographic where they fall at oblique angles upon the plane of projection. The second of these projections is the more important, and must be tr2atcd here in some detail. Two points are to be noted in regard to it. In the first place, in the drawings of crystals the point of view is supposed to be at an infinite distance, and it follows from this that all lines which are parallel on the crystal appear parallel in the drawing. In the second place, in all ordinary cases, it is the complete ideal crystal which is represented, that is, the crystal with its full geometrical symmetry as explained on pp. 10 to 13 (cf. note on p. 13). In general, drawings of crystals are made, either by constructing the figure upon a projection of its crystal axes, using the intercepts of the different faces upon the axes in order to determine the directions of the edges or by constructing the figure from the gnomonic (or stereographic) projection of the crystal forms. Both of these methods have their advantages and disadvantages. By drawing the crystal figure by the aid of a projection of its crystal axes the symmetry of the crystal and the relations of its faces to the axes are emphasized. In many cases, however, drawing from a projection of the poles of the crystal faces is simpler and takes less time. The student should be able to use both methods and consequently both are described below.

Jan 1, 1922

By William E. Ford, Edward Salisbury Dana

A. Anhydrous Carbonates The Anhydrous Carbonates include two distinct isomorphous groups, the CALCITE GROUP and the ARAGONITE GROUP. The metallic elements

Jan 1, 1922

By Graham John Mitchell

In May, 1919, a crosscut on the 1400-ft. level of the Briggs mine, a Calumet, & Arizona property at Bisbee, Ariz., penetrated a deposit of pyrite and chaleopyrite that had replaced quartzite and limestone and was cut, especially in the quartzite, by numerous fractures. As the drift advanced through these fractured portions, they were found to be free from copper-sulfate minerals although '(sooty" chalcocite was present in the fractures and also as coatings and replacements of pyritc. Howcver, sulfate soon made its appearance in certain fractures, filled them, and began to form stalactites. Several centers of incipient growth were noted for subsequent study, observations in the drift at frequent intervals during the past 17 months affording the opportunity of determining the rate of formation of the stalactites. The one to attain the greatest growth during the period of observation measured 27 in. long and averaged 1 in. in diameter. A close study showed it to be composed of small interlocked crystals of chalcanthite radiating from a small central tube-like opening. The trielinic form of the crystals was evident with prism and pinacoid faces recognixable. Assuming that the supply of copper-sulfate solution was constant (luring the 17 months—-and such an assumption is supported by the fact that the number of drops of excess solution falling, per minute, from the tip of the stalactite at the times of observation checked closely—thc stalactite, it has been estimated, grew at the rate of 1.58+ in. per month. DISCUSSION James I?. Kemp," New Yolk City.—J. S. Curtiss, in the monogr:tpll on Eureka, Ncv., say:: that a stalactite formed in limestonc grew 5/8 in. in three weeks and continued to grow as long as it had a drop of water or solution at the lower end. Another grew at the rate of 3/8 in. in the same time. In the case cited by Mr. Mitchell, the growth was about 136 in. in three weeks. A year ago we had an instance of the formation of cubes of galena on a railroad spike. A mine in northeastern Oklahoma had been idle about two years but on account of pumping of neighboring properties, the circulation of water was active throughout the drift. A cube of galena,

Jan 1, 1922

By William E. Ford, Edward Salisbury Dana

In their action upon the senses a few minerals possess taste, and others under some circumstances give off odor. 444. Taste belongs only to soluble minerals. The different kinds of taste adopted for reference are as follows: 1. Astringent: the taste of vitriol. 2. Sweetish astringent: taste of alum. 3. Saline: taste of common salt. 4. Alkaline: tast'e of soda. 5. Cooling: taste of saltpeter. 6. Bitter: taste of Epsom salts. 7. Sour: taste of sulphuric acid.

Jan 1, 1922

By H. T. Mercer, A. C. Paulson

The composition of steel and the theory of its heat treatment have been so ably discussed elsewhere that it is unnecessary to go into the subject here. The purpose of this paper is to describe briefly the method of treating drill steel at the Copper Range mines, giving some of the troubles encountered and the manner in which they were overcome or corrected. To study the matter properly, it was necessary to devise a system of records that would show the actual underground performance of the drills. To illustrate this system, the records of the Champion mine are used, as it is at this mine that most of the work along these lines has been done. Reports from each drill machine are made daily by the shop and mine, and tables compiled from these reports show the footage drilled, steel broken, drills received and sent out at the shop, drills sharpened, and bits cut off. These data show what each machine or party is doing and whether the miners' supply of drills is kept up to date. There have been times when the supply of drills has been short and time lost by the miner in looking for drills. The daily records show the number and condition of drills on hand at all times. Under the old method of sharpening, the drills were heated in a coke furnace, the proper degree of heat being judged by color. Then they were sharpened in a machine, reheated in a second coke furnace where the proper heat was again determined by color, and quenched in water. While this method was fairly successful in the hands of a careful workman and for the solid steel used in the old piston drill machine, the introduction of the faster water machine, using hollow steel, produced changes both underground and in the shop. Much more was expected of the hollow-steel and hammer-type machine, with its improved method of rotation, but troubles due to breakage, burnt bits, uneven tempering, etc., at once appeared.

Jan 1, 1922

MARSHAL Foch has been made an honorary member of the four national American societies of civil, mining and metallurgical, mechanical, and electrical engineers. The governing bodies of these societies, aggregating 45,000 members, conferred this signal honor in expression of the appreciation of American engineers for the unmatched services of this master of engineering principles. At Engineering Societies Building, in New York City, on Tuesday afternoon, Dec. 13, the presidents of the four societies presented one beautifully engrossed certificate of honorary membership in the four societies. The auditorium was filled so that not even standing room was left, more than a half hour before the cere-monies began, and the main entrance on the street had to be closed. J. Vipond Davies, president of the United Engineering Society, made the opening address. Col. William Barclay-Parsons, 'who was commander of the first engineer regiment to go abroad, addressed Marshal Foch in French. Colonel Parsons said: The art of engineering was defined a long time ago as "the art of directing the great sources of power in nature for the use and convenience of man." No better definition can be found today. Of all the sources of power in nature, the greatest, the most valuable, and at the same time the most difficult to direct, is the energy of man himself. He who can direct human energy and turn it to the service of mankind is a great engineer. You, Marshal, have directed a greater mass of human energy than any other man has ever done. And you have successfully directed this mass for the highest uses of mankind, in that you by its aid have preserved for him one of the most precious of human possessions-liberty-liberty not only for your own illustrious country, but for all the nations of the world. The four national engineering societies, of the United States now desire to make record of their appreciation of this fact and to convey to you an expression of their most profound admiration for the great leader of men by conferring on you honorary member-ship in all the societies, the highest honor in their gift and one hitherto never conferred on a single individual. Four thousand members of these societies were enrolled in the armed service of the United States, the greater part of whom had the glorious distinction to serve the common cause in France under your orders. They heard the voice and they saw the hand of the master as he led them through battle to victory. Now we desire that you will still continue to lead us, but in peace, by permitting us to inscribe your name at the head of our roll of honor, where it will be, as your deeds have been, an example to us to do better work, and where it will remain forever a noble inspiration for all future generations. Marshal, in the name of those members of the societies who served under your orders and particularly .in the name of those who fell on the field of honor in France, I salute you.

Jan 1, 1922

By H. N. Eavenson

The eleven mines of the United States Coal and Coke Co. in the Pocahontas coal field are situated in McDowell County, W. Va., which is a mountainous region. The valleys rarely exceed 200 ft. (60 m.) in width, the hillsides slope from 25°to 33°, and the tops, from 600 to 900 ft. above the valleys, carry practically no level land. At least 80 per cent. of the area is covered with timber. All the workings are drift mines; and while the average grades of the seams worked are ample for drainage, local dips and swamps necessitate the use of a large number of local pumps or of numerous drainage ditches to keep the mines free from water during heavy rains. The water handled in any mine is not great, compared with the coal output, and usually causes little trouble except during extremely wet periods. In new workings, the water encountered, except in rare cases, is trifling; it is only after rib drawing has started and the surface has been broken that water troubles begin. The strata overlying the coal are sandstone, shales, and slates; as the soil is thin and sandy, it does not tend to puddle and stop the cracks, which remain open for a long time. As mining progresses and the robbed area increases, the broken area becomes larger, increasing the openings into the mined territory. The cover over the robbed portions of the mines varies from 30 to 750 ft. (9 to 228 m.). When the ground is saturated, considerable water finds its way into the mines the day after a heavy rainfall and for three or four days it tends to fill the low places, wash the tracks, etc. and unless from three to four times as many pumps are installed as are normally needed, considerable output is lost. In most cases the water will flow from the mines, and the obvious solution is to provide drainage ditches of ample size to carry the maximum flow expected, so that the inflow will have no opportunity to flood the working places. Laying out the drainage headings on the proper average grades was an easy matter but where blasting was necessary to provide uniform grades, as was frequently the case, it was important that the maximum flow to be expected and the size of ditches to be provided should be known so that only rock work necessary to provide proper drainage

Jan 1, 1922

Joseph William Richards, was born in Oldbury, Worcestershire, England, on July 28, 1864, of English-Scotch parents, Joseph and Bridget (Harvey) Richards. In 1871, he came to this country with his parents. He attended the public schools of Philadelphia, Pa., where his father was a manufacturing metallurgist, and in 1882, graduated from the Central High School with the degree of A. B. The same year he entered Lehigh University, from which he received the degree of A. C. (Analytical Chemist) in 1886; M. S. in 1891, and Ph. D. in 1893. His connection with the university was continuous from 1887 until his death, and he therefore adds another to the list of names of men Prominent in the A. I. 11. E. who have helped to develop Lehigh University to the important position which it now occupies in mining and metallurgical education in respect of world-wide fame. It is fitting to recall in this connection that, Eckley B. Coxe, a fonnder of the A. I. M. E., four times its vice-president,, and president in 1878-79, was literally a pillar of the university for several years prior to his death; Thomas M. Drown, founder, vice-presi(lent, secretary for 11 years, honorary member, and president in 1897, was president of Lehigh University from 1895 to 1904; and Henry S. Drinker, founder, manager, vice-president, and honorary member, was president of the university from 1905 to 1920. Doctor Richards was no less active in both institutions. With the exception of the years 1886 to 1887, when he was superintendent of the Delaware Metal Refinery of Philadelphia, his professional life was devoted to the upbuilding of the metallurgical department of the university, in part through his continuous services as a member of the teaching staff, and in part through the international renown won for the department by his achievevements as author, investigator, expert and rerognizcd authority in metallurgy, especially the metallurgy of aluminum, metallurgical-chemical calculations, and electrometallurgy. He was assistant instructor in metallurgy and blowpiping in 1887; instructor, 1888-90; instructor in metallurgy, mineralogy and blowpiping, 1890-97; assistant professor, 1897--1903; professor of metallurgy, 1903-1921. He died at his home in Bethlehem, Pa., on Oct. 12, 1921, of heart failure. To the A. I. M. E., for a continuous period of a dozen years, his services were equally loyal and effective. He was vice-president, 1910-11, and 1916-17; councilor, 1912; dirctor, 1913-15; chairman of the Iron and Steel Clommittee, 191-1-21; he was one of the framers of the Insti-

Jan 1, 1922

By William E. Ford, Edward Salisbury Dana

This section includes the common calcium titano-silicate, Tiianite; also a number of silicates which contain titanium, but whose relations are not altogether clear; further the titanate, Perovskite, and niobo-titanate, Dysanalyte, which is intermediate between Perovskite and the species Pyrochlore, Micro- lite, Koppite of the following section. In general the part played by titanium in the many silicates in which it enters is more or less uncertain. It is probably in most cases, as shown in the preceding ages, to be taken as replacing the silicon; in others however, it seems to play the part of agaaic element; in schorlomite (p. 510) it may enter) in both relations.

Jan 1, 1922

By William E. Ford, Edward Salisbury Dana

Twin crystals are those in which one or more parts regularly arranged are in reverse position with reference to the other part or parts. They often appear externally to consist of two or more crystals symmetrically united, and sometimes have the form of a cross or star. They also exhibit the composition in the reversed arrangement of part of the feces, in the striae of the surface, and in re-entering angles; in certain cases the compound structure can only be surely detected by an examination in polarized light. The above figures (Figs. 384-386) are examples of typical kinds of twin crystals, and many others are given on the pages following.

Jan 1, 1922

By J. Ellzey Hayden, Lucien Eaton

The Cliffs Shaft mine of the Cleveland Cliffs Iron Co., located in the city of Ishpeming, Mich., is the largest producer of hard hematite ore on the Marquette iron range. The two shafts, A and B, lying 820 ft. (250 m.) apart on the east-west trend of the ore formation, were sunk in the early eighties, and, except for four years, have been steady producers of iron ore. Their location, on a hill overlooking the general offices of the company on the one side and the city of Ishpeming on the other, has made the shaft houses landmarks. In the spring of 1919, as the old wooden shaft houses had become shaky and out of line, and would soon be unsafe, it was necessary to replace them with the least possible delay. Three plans of construction were, therefore, considered: To replace the old shaft houses by somewhat similar structures made of wood; to use steel and radically change the design; or to build reinforced-conerete shaft houses outside of the wooden structures, completely enclosing them. The first plan was disapproved, because it is anticipated that the mine will have a long life and the proximity of other buildings makes the danger from fire rather great. Delay in receiving material, and the necessity for closing the shafts during erection, were other factors in the situation. The second plan was disapproved on account of the high cost of steel, slow delivery, and interference with hoisting during the period of erection. The presence near one of the shafts of a large bed of hard gravel suitable for concrete made the cost of the third plan considerably less than the second, and little, if any, delay in hoisting was expected. Our expectations in this regard were fully realized. Furthermore, the work could be done by unskilled labor, which was plentiful, and the erection could be quickly started. When the proposition was submitted to W. G. Mather, president of the company, he recommended that, on account of the prominence of the buildings due to their location, an effort should be made to combine in the design as far as practicable something of architectural beauty. Following his recommendation, the original plans were submitted to the

Jan 1, 1922

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922

Jan 1, 1922

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922