Search Documents

By R. J. Pruett

The Georgia kaolin district is the world’s largest producer of kaolin. Georgia production tripled from 2.87 Mt (3.17 million st) in 1968 to8.35 Mt (9.2 million st) in 1998. Development of the Georgia kaolin industry can be traced to the identification of the mineral resource, the adoption of innovative process technologies and the creation of markets for kaolin. Georgia kaolin is an abundant and high-quality resource that shows a range of advantageous properties. Technical developments in wet processing, delamination and calcination allowed production of high-value products. The use of kaolin pigments in the paper industry provided a market that absorbed the rapid growth in kaolin production.

Jan 1, 2000

By Normand Tassé

Reactive barriers, which consume oxygen, are prospective though unconventional alternatives to physical barriers for Acid Mine Drainage prevention. However, a reactive barrier implies a problem of duration. Pore gases were analysed in several wood waste piles in order to understand the factors which control wood degradation and help to determine the effective life span of such a cover. Long term efficiency seems to strongly depend on the degree of water saturation at the bottom of the pile, likely because the development of a microbial biomass in such an environment helps to keep the amounts of nutriments and readily metabolizable organic substrates at a high level, which in turn promotes oxygen consumption.

Jan 1, 2000

By R. Haecker, S. Gupta, P. Somasundaran

Rock disintegration processes are usually inefficient and costly operations in mineral beneficiation, mine development and oil well preparations. Thus, there is a strong need for improving the energy efficiency of unit operations such as drilling and comminution. The effects of selected cations and anions on drilling efficiency in a hard rock formation (Dakota Sandstone) were studied. The zeta potentials and the tensile strengths of the drilled samples were measured under similar chemical conditions. The chemicals tested included MgCl2, Na2CO3, AlCl3, NaCl and Dodecylammonium chloride. The results indicated that drilling rates can be enhanced or retarded depending on chemical conditions such as the solution pH and the type and concentration of reagents. Drilling data are correlated with mechanical (tensile strength) and interfacial (zeta potential) properties of the rock formation. The mechanisms involved are discussed in light of Rehbinder's and Westwood's theories.

Jan 1, 2000

By T. N. Singh, M. M. Singh, R. B. Singh

Fly rock is common when blasting shallow holes and during secondary blasting. Although the required quantity of explosives for secondary blasts is less, noise and fly rock can have an enormous environmental impact. This paper mainly deals with field experiments on blast-design parameters and addresses some precautionary measures that can be taken when pop shooting.

Jan 1, 2000

By B. K. Mishra, A. Datta

Estimating the power draw of a ball mill is of great importance from both operational and control standpoints. There are many factors that affect the power draw, and its prediction is particularly difficult in an operating plant. The important factors that affect power draw are the mill dimensions and operating parameters. Although mill dimensions remain the same for any given mill, the operational factors, such as ball load, mill filling and mill speed, may vary. This makes the modeling effort extremely cumbersome. It is for this reason that an artificial neural network is considered for the development of a black-box-type model to predict power draw. In this work, a total of 48 sets of plant data are used. Using these data, a neural network is built and trained. The trained network is used to predict power that is found to be in good agreement with operating mill power for many situations. In addition, the results of simulations are also com- pared to those obtained from a discrete-element method- based power-draw model.

Jan 1, 2000

By J. C. Yingling, R. Kumar, J. Sottile

The capability for on-line measurement of the quality characteristics of conveyed coal now enables mine operators to take advantage of the inherent heterogeneity of those streams and split them into wash and no-wash stocks. Relative to processing the entire stream, this reduces the amount of coal that must be washed at the mine and, thereby reducing processing costs, recovery losses and refuse-genera¬tion levels. In this paper, new ap¬proaches for optimal control of the segregation process using time-se¬ries models and empirical distribu¬tions are presented and demon¬strated using field data.

Jan 1, 2000

By O. H. Tuovinen, T. M. Bhatti

Microbiological leaching has been used as an alternative approach to conventional hydrometallurgical methods of uranium extraction. In the microbiological leaching process, iron-oxidizing bacteria oxidize pyritic phases to ferric iron and sulfuric acid, and uranium is solubilized from the ore due to sulfuric acid attack. If uranium in the ore material is in the reduced, tetravalent form (UIV), a red ox reaction is involved whereby uranium is oxidized to the hexavalent form (UvI) upon dissolution. In acid-leaching systems, the primary oxidant is ferric iron, which is reduced to ferrous iron by its chemical reaction with UIV. The ferrous iron thus formed is reoxidized to ferric iron by iron-oxidizing bacteria such as Thiobacillus ferrooxidans and Leptospirillum ferrooxidans. Nutritional requirements and responses to environmental extremes of acidophilic iron-oxidizing bacteria are appraised. The S-entity in Fe-sulfides is oxidized to sulfate by bacteria similar to Thiobacillus ferrooxidans and Thiobacillus thiooxidans. Pyrite and marcasite oxidation is a sulfuric acid forming reaction. Heap, dump and in situ leach techniques are feasible as bacterial leaching systems.

Jan 1, 2000

By Shawn Benner, David Blowes, Carol Ptacek

A full-scale reactive barrier was installed into an aquifer impacted by acid mine drainage in August 1995 at the Nickel Rim mine site near Sudbury, Ontario. The primary mechanism of water quality improvement is bacterially mediated sulfate reduction and metal sulfide precipitation. Dramatic changes in the groundwater chemistry are observed with up to 90% decline in Fe (from >18 to <2 mmol L-1) and increases in alkalinity from <1 to >10 mmol L-1 (as CaCO3). Over a 3 year period, the rate of Fe removal declines by approximately 35%. Primary controls on barrier performance are organic carbon reactivity, groundwater temperature, and variable residence time within the barrier.

Jan 1, 2000

By A. C. T. Bigg, Y. Kocak, N. K. Bodur

The Gumuskoy silver mine, owned by the Etibank, in the province of Kutahya, Turkey, has been operating since 1987 with primary, secondary and tertiary crushers, and two parallel single stage ball mill circuits. Continuing problems with crushing and feeding of the ore to the ball mills, because of the moisture retaining and sticky nature of the ore, prompted an investigation into the possibility of converting the grinding circuit to an autogenous or semiautogenous grinding circuit. This would remove the bottleneck associated with the secondary and tertiary crushing. At the same time the target feedrate is to be raised from 140 t/h to 175 t/h. This paper demonstrates the response of five ore types, and blends of ore types in an onsite pilot plant test program, and also suggests how the variations can be handled in a SAG mill/ball mill circuit incorporating just one of the present ball mills.

Jan 1, 2000

By Winfield G. Wright, Philip L. Verplanck, Philip L. Hageman, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

Geological, hydrological, and geochemical information synthesized in a Geographical Information System (GIS) for water and rock surrounding South and Middle Forks of Mineral Creek, northwest of Silverton Colorado, was analyzed to distinguish between the natural and the mining-related sources of metals to dace waters in the watershed An important natural source of metals to surface water emanates from a porphyry molybdenum deposit south and upslope from the Middle Fork of Mineral Creek. Interaction of surface and ground water with fractured, altered rocks and permeable, Quatemay-age surficial deposits produces downstream water quality that does not meet current State of Colorado water quality standards for metals and pH. GIS site characterization and three-dimensional modeling distinguish surficial deposits as volumetrically substantial, significant sources of naturally occurring metals that strongly influence water quality and complicate ongoing mine-site mitigation efforts. Our findings indicate that regional hydrologic and geologic information needs to be evaluated before realistic water quality guidelines are established and mitigation recommendations are confidently implemented.

Jan 1, 2000

By Lars Olaf Höglund

MiMi has been set up to be i) visionary, ii) strategic and iii) long-term. The planning as well as the executive phases involves industry, academia and authorities in close co-operation. MiMi focuses on improved, economically efficient management of mining waste, a challenge that requires combined and integrated research efforts across discipline boundaries. The MiMi programme is financed by the Swedish Foundation for Strategic Environmental Research (MISTRA) with support from the mining industry. The first programme phase covers the period 1997 - 2000, with intentions for additional phases. Planning, experience and results from the first programme period are highlighted. INTRODUCTION Most of the mining activities in Sweden takes place in the No

Jan 1, 2000

By Robert L. Runkel, D. Kirk Nordstrom, James W. Ball

Low-flow reactive-transport processes in Wightman Fork downstream of the Summitville Mine, south-central Colorado were simulated using the OTIS and OTEQ solute-transport models. The simulation was calibrated using data from a synoptic study conducted during October, 1998. Discharge over the 8-km reach from just below the mine site to the Alamosa River confluence ranged from 0.077 to 0.17 m3/s; travel time was 10.7 hours; pH ranged from 4.6 to 5.7. Simulations revealed that mass balance for SO4 was maintained, and that pH, Fe, and Al were non-conservative. Simulations allowing hydrous ferric and aluminum oxide or hydroxysulfate precipitation matched observed water quality conditions more closely than simulations without precipitation.

Jan 1, 2000

By Tim O’Neil

The search for precious metals opened up the American West. And Nevada was right in the heart of this development. In the mid-19th century, prospectors seeking gold roamed the hills of Nevada and discovered the ComstockLode. The development of this huge silver and gold deposit began in1859 and was responsible for Nevada’s early entry to statehood. Mining was Nevada’s first industry. In more recent years, the Nevada mining industry has led the nation in gold, silver and barite production. Nevada also produces many other minerals. These include aggregates, clays, copper, diatomite, dolomite, gypsum, lime and limestone, lithium and magnesium compounds, perlite, salt and silica. Even today, Nevada’s mining industry continues to be a major economic force in the state. The mining industry has made more than $10 billion in capital investments in Nevada since 1985. And the value of Nevada’s mineral production last year was about $2.7 billion.

Jan 1, 2000

By M. H. H. Mahmoud, T. A. El-Barbary, E. A. Abdel Aal, I. A. Ibrahim, A. K. Ismail

Fertilizer-grade phosphoric acid with a P2O5 concentration of 50% should contain less than 1.5% Fe2O3, otherwise, the P2O5 water solubility of the fertilizers prepared from high-iron acids will be low. High-iron Egyptian phosphate concentrates fromAbu-Tartur and Sebaiya- West were leached with sulfuric acid and recycled phosphoric acid to produce 50%-P2O5 phosphoric acids containing 4.0% and 2.7% Fe2O3, respectively. The high iron contents were reduced to the industrially accepted limit of 1.5% Fe2O3 by precipitation with potassium sulfate. The factors affecting the effi¬ciency of the precipitation process, e.g., temperature, time and K2O/Fe2O3 ratio, were systematically studied, and the optimum conditions were achieved. The clarification of the prepared phosphoric acid from iron-containing sludges was also investigated by varying the time and temperature. The utilization of the separated sludges as fertilizer and recovery of P205 by pulping in water were also evaluated.

Jan 1, 2000

By Lewis Gordon, Alan Morrow, Aundra Nix

At the ASARCO Mission Mill, a multivariable, predictive controller was used to optimize parallel grinding circuits, improving throughput and product size. Using a dynamic model of the grinding circuit developed from on-line testing the software manipulates 4 variables to control 14 quality and constraint variables in each circuit. Traditionally, model-based control in grinding is difficult due to ore changes. This is addressed via a novel method to predict mill overload and automatic model switching.

Jan 1, 2000

By Erik A. Munroe, Nelia W. Dunbar, Virginia T. McLemore

In New Mexico, there are at least 100,000 abandoned mine waste rock piles with widely ranging geochemical and mineralogical compositions. A geochemical and mineralogical study was implemented for five waste rock piles, some which contained sulfides, in the Hillsborn Mining District. Chemical and physical characteristics of mineral grains and their secondary mineral oxidation rinds were examined with the electron microprobe. Pyrite and chalcopyrite appear to be the most reactive to oxidizing conditions. Clays, iron oxide, iron hydroxide, iron sulfate, and primary texture rinds exist in the waste rock piles analyzed.

Jan 1, 2000

By S. Finsterle, R. C. Trautz

We performed numerical modeling studies to investigate water seepage into underground openings excavated in unsaturated fractured rock. Water seepage is a key factor affecting the performance of a nuclear waste repository such as the one proposed at Yucca Mountain, Nevada. The amount of water dripping into an underground opening depends on the connectivity and permeability of the fracture network as well as on the capillarity of individual fractures intersecting the opening. We developed a high-resolution numerical model of an unsaturated fracture network and examined the appropriateness of seepage predictions using a fracture-continuum model. Model calibrations to liquid-release tests performed at Yucca Mountain are also discussed.

Jan 1, 2000

By Kim A. Lapakko, David A. Antonson, Jon R. Wagner

This study examined the potential of mixing rotary kiln fines (RK fines), a waste product generated when limestone is converted to lime (CaO), with acid producing mine waste to provide 1) short-term mitigation by neutralizing acid produced by iron sulfide oxidation and 2) long-term mitigation by facilitating the passivation of iron sulfide mineral surfaces. Five loadings of RK fines were mixed with 75 g of Duluth Complex rock to produce neutralization potential (NP) added: acid potential (AP) quotients of 0,0.11,0.22,0.66 and 1.1. The mixtures were subjected to wet-dry cycling laboratory testing for 585 weeks. The rock alone produced acidic drainage, with pH decreasing below 4 after about 20 weeks of reaction and ultimately reaching the approximate range of 3.3 to 3.5; sulfate release did not decrease over time. The RK fines elevated pH and inhibited sulfate release for time periods which increased with the mass of RK fines present. The pH of drainage from the 0.11 quotient (NP added1AP) loading decreased below 6.0 after 75 weeks of dissolution and decreased to 3.6 after 117 weeks, at which time the reactor was terminated. The duplicate 0.22 quotient loadings of RK fines decreased below 6.0 after 95 and 170 weeks. The former was terminated after 117 weeks, and the latter reached a minimum pH of 2.8 after 512 weeks. Drainage pH from the 0.66 quotient decreased below 6 after 581 weeks. For the drainages which acidified, the cumulative calcium release prior to pH decreasing below 6.0 was 92 to 103 percent of that initially present as calcium carbonateloxide in the RK fines. The pH of drainage from the 1.1 quotient typically remained above 8.0 throughout the period of record. Sulfate concentrations in the drainages decreased while the neutralizing fraction of the RK fines was present, but increased after this fraction was depleted.

Jan 1, 2000

By Edmond O’Donovan

Selection of conveyor drives is an area of great confusion that frequently leads to poor system performance or overcapitalization. Many papers have dealt with the performance characteristics of different drive types, but users have often found that this only leads to further confusion. This paper presents the drive requirements from the "conveyor&apos;s" point of view. The drive requirements of different classes of conveyors are examined to illustrate why some drive types work well in certain situations but poorly in others. The appropriateness and shortcomings of different drives are examined in this context, along with the recurrent issue of load sharing.

Jan 1, 2000

By Michael J. Rinker, R. V. Nicholson

Waste rock and tailings from a proposed nickel-copper mine were evaluated extensively for potential on-land and under water disposal. Standard humidity cell and column tests were conducted over a two year period and underwater tests were conducted for more than one year. Nickel concentrations or release rates from the waste were consistent with nickel to sulphur ratios in the solids. This relationship provided a tool to assess the risk of metal leaching in wastes using nickel and sulphide assays. Nickel release and mobilization was found to occur for both oxidizing leach tests and under water tests even when pH values exceeded 7.0. Geochemical model calculations showed that iron oxyhydroxide solids can scavenge nickel from leachate and that the nickel inventory can be released from solids at relatively lower, but neutral pH values.

Jan 1, 2000