Search Documents

By Stephan Fisch, Franz-Werner Gerressen

"The use of cut-off-walls (COW) for the open pit coal mines has been used for decades. They have been used to reduce the negative hydraulic impact to the surrounding area caused by the open pit mining. The pile-guided trench cutting system is a worldwide unique technique, originally developed by the engineers of the mining companies themselves. It guarantees a continuous, joint free, COW during a continuous installation process. At this specific site in Welzow, this technique has been pushed to new limits in order to address the local lake region. Depth capability has been designed to about 430 ft (130m), proven are already depth of about 360 ft (110m) at a constant trench width of 39 inch (1000 mm). This project is approximately. 6.8 miles (11 km) long of COW, scheduled to be completed in 12 years period. About 2.05 miles (3.3km) have been installed, which is equivalent of about 3.5 Million ft² (330,000 m²). The system flushes special clay which forms a filter crust at the inner surface of the trench. Only natural clay resources used, in order to achieve the cut-off effect (colmation effect). The paper explains the installation process of the cut-off-wall as well as the equipment systems developed specifically for this project. After a successful start of the first phase of the project, the next step in the advancement of the equipment is already underway to enable the installation of greater depth to approximately 490 ft (150 m +) and beyond. The next generation equipment system is scheduled to start operation around 2018 INTRODUCTIONThis Serbian saying “Bóh je stworil Lužicu a cert je zaryl brunicu – God created Lusatia and the devil buried brown coal underneath it.” captures local communities’ ambivalence towards lignite.Lusatia is an almost entirely flat stretch of land between the Elbe and Neiße rivers dominated by glacial sands. On the surface, the heathland and woodland is hardly noteworthy. However, three large lignite mining regions, two in Brandenburg and one in Saxony, in the east part of Germany, divert the attention to underground level, down to depths of up to 120 meters. Here, seams crisscross the earth like ribbons. They were formed in the Tertiary around 17 million years ago.The mining of the lignite started almost 200 years ago. To enable open pit mining, a suitable dewatering system was required. At first, wells and drainage system were used. With the increasing demand to go deeper to enable full use of the existing resources with greater mining depth, a decision taken back in the 60th of the last century, the amount of water which had to be pumped increased dramatically. In peak times, approx. 1.57 Billion cubic yards per year (1.2 Billion m³/year) had to be pumped. This led to a lowering of the groundwater level for up to 230 ft (70 m), impacting the regional lake landscape. In order to reduce the influence on the water balance, and bring the water level back to pre1970th, a first development took place to implement the use of specific COW system to depth of about 147 ft (45m)."

Jan 1, 2017

By Paul J. Sabatini, Robert C. Bachus, Terence P. Holman, Panos Andonyadis

A recent landslide comprising approximately 12 acres (4.86 hectare) and a displaced volume of more than 500,000 cy (382,000 m3) caused the shutdown of a four-lane state highway and two high-capacity freight railway lines. After completion of immediate landslide stabilization activities, various long-term slope stabilization measures were implemented that focused primarily on gradual slope unloading in areas near and upslope from the scarp of the landslide. Near the completion of the upslope excavation, an anchored soldier beam and lagging wall was constructed to allow for the temporary unloading of the toe of the main landslide area to facilitate installation of a permanent underdrain. The design of the anchored wall utilized information collected during the rehabilitation construction and included inclinometer data, site survey results, piezometer data, and field construction observations. Using the history of site-specific movements, results of back-analysis calculations from the landslide, and geometry/performance of the post-construction slope configurations, the fully softened and residual shear strengths along two potentially critical sliding surfaces were calculated. Owing to the high confidence in the values of shear strength as afforded by this information, the confidence in local groundwater conditions, and control of the loads, the designers selected a relatively low, calculated short-term factor of safety (FS) (i.e., FS ˜ 1.1 to 1.2) for the most critical unloading step. Long term calculated FS values on the order of 1.2 to 1.3 were anticipated. This paper describes the detailed evaluation of the landslide slope movement data associated with the shallow and deep potentially critical failure surfaces and selection of the associated values of design shear strength for these potentially critical surfaces. A description is presented of the analyses and design of the anchored wall, measures implemented during construction to minimize slope movements, and post-construction monitoring results during the unloading and subsequent installation of the underdrain.

Jan 1, 2017

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By E. S. van Druten, M. C. Bekker

"The complete and successful closure of a mine in the South African environment remains problematic. Closure remains an elusive mining phase due to unclear roles and responsibilities, inaccurate closure management data, and the inability of stakeholders to conceptualize and integrate closure information into business processes. Currently there are no proven methods available to address the complexities encountered during a closure application, and to date no mine has been granted full closure. Many mines are left abandoned and unrehabilitated, resulting in risk to investors, surrounding communities, and regulators. This investigation aimed to determine, categorize, and rank reasons for unsuccessful mine closures. Focus groups consisting of public and private stakeholders were identified and surveyed through a structured, rank-order questionnaire to determine the relative importance of reasons why achieving formal and final mine closure remains elusive. Various requirements and aspects were identified and listed according to four categories: namely, primary, secondary, process drivers, and information sources. These aspects should be considered in the development of an integrated mine closure model.Background and rationalePrior to 1956, mine closures were not subject to legislative requirements, being merely governed by insufficient environmental regulations under the Mines and Works Act 27 (MWA) (Swart, 2003). In 1981 the Chamber of Mines (COM) published a document titled ‘The rehabilitation of land disturbed by surface coal mining’, which constituted the first notable contribution to environmental protection. This guideline was later referenced in the Minerals Act of 1991, which for the first time laid definite environmental burdens on the Mining Right Holder (MRH). The Minerals Act of 1991 was superseded by the current Mineral and Petroleum Resources Development Act (MPRDA) and the Mineral and Petroleum Resources Development Act Regulations (MPRDAR), which specify a regulatory process for mine closure applications and financial provisions."

Jan 1, 2017

By Katya V. Babenko, Victor V. Nazimko

We address the problem of the stochastic nature of ground pressure manifestation. Stress distribution in a rock mass and ground irreversible movement are governed with a set of random factors that affect the over-peak strength of the rocks, making them extremely sensitive to any perturbation of the external environment and to internal fluctuations of the thermodynamic state of the rock. We investigate the fluctuation evolution during a longwall face movement to find out whether the fluctuation dissipates or builds up. Five adjacent powered support failures simulate the ground pressure fluctuation. The main roof has been presented as a plate that reposed on the rigid base. The stiffness of the base depends on the thickness of the extracted coal seam and on the dilation of the caving roof. Maximum stiffness occurs in situ, and minimum stiffness is in the gob when the roof is highly flexible and subsides elastically, without caving. The more stress acts in the roof, the higher the cavity that occurs and the larger increment of the base stiffness. The wave of the fluctuation has extended both to the direction of the longwall advance and along the face from the point of the fluctuation agitation. There was an incubation period when the fluctuation was negligible, and the process of the main roof caving remained unaffected. The distance of the longwall advance during the incubation period was twice the longwall length when the fluctuation magnitude was 1% relative to the maximum possible disturbance and 0.76 of the longwall length for the magnitude of 24%. However, the pattern of the roof caving has dramatically changed during further movement of the longwall. All caving parameters have changed: step of the caving, ground pressure distribution, and the manifestation in the longwall and entries. A histogram of the fluctuation magnitude is symmetric in accordance with normal distribution. However, the distribution has abnormal excess. These findings are the first step toward answering the question whether it is possible to forecast the process of main roof caving and weighting consistently. Our preliminary conclusion is that the space and time intervals where this prediction can be made with certain reliability are limited, so further investigation is needed.

Jan 1, 2017

By Nicholas Dyriw, Georgy Cherkashov, Tamara Stepanova, John Parianos, Anna Firstova

"Seafloor massive sulfide (SMS) deposits are a new frontier in global metal resources. Hydrothermal chimney’s (black smokers) precipitate Cu, Zn, Ag and Au rich from hot fluids (>250°C) during interaction with cold seawater ~2-4°C. Here we compare the sulfide mineralogy and geochemistry of Cu-sulfide chimney samples from two different tectonic locations: Solwara 1, a Cu-rich, transitional arc-back arc (Arc-BA) type SMS ore deposit and; Ashadze-1, a Cu-rich, ocean ridge type SMS deposit (Hannington et al., 2011).This work represents the first stage of a project aimed at investigating and understanding the significance of high Cu concentrations in SMS systems. Comparing these particular systems is significant because they share critical similarities despite being located at different seafloor depths, hosted in different rocks and are located in two different endmember tectonic environments. Critical similarities include: 1) age of mineralization, ~6000 years to current (Firstova et al., 2016; Johns et al., 2014); and 2) high copper contents, with chalcopyrite dominating sulfide mineralization (Firstova et al., 2016; Lipton, 2012). The reason for high Cu concentrations in both of these locations is still not entirely understood. The youthfulness (<6000y to current) of both locations is important because it reduces the possibility of increased zone refining, allowing us to understand the source characteristics better. This research will advance our understanding of the copper systematics of SMS systems by investigating and comparing the mineralogical and geochemical signatures from two, Cu-rich, end-member type SMS sites."

Jan 1, 2017

By Luiz Guilherme Isfer Maciel, Marilena Cardu, Fernando Golin, Jacopo Seccatore

"This study applies the concept of the difficulty of tunnelling by drilling an blasting (D&B) to selectedcases from the Brazilian tunnelling industry. The difficulty of tunnelling has been defined in previouswork as the difference of specific drilling (SD) from industrial average trend: easier when SD is lowerthan average, more difficult when SD is higher than average. Results show how tunnels in Brazil tend tobe unrealistically more difficult to excavate when compared to similar excavations in similar geologies elsewhere in the world. It is thoroughly discussed the reason for such anomaly (up to +90% SD compared to industrial average). One reason could be the lack of options amongst explosive products on the brazilian market. Only ANFO and explosive emulsions are available in Brazil. Lacking high VOD(Velocity of Detonation) products might result in reducing the maximum allowable burden amongstproduction holes, therefore increasing SD. Another reason could be found in the tunnel designers’tendency of choosing D&B as excavation method for weak rock masses that would benefit from mechanical excavation. The reason to this tendency can be partly found in the lack of availability of mechanical excavation machines in the brazilian market. Blasting in weak rock masses requires more careful smooth blasting, hence a closer spacing amongst contour holes to avoid costly overbreak: this increases SD. A third reason could be found in the lack of skill amongst the local workforce. When dealing with unskilled workers the blast designers naturally tend to avoid highly optimized blasts thatrequire very skilled workforce to be realized on field. The designer in this case tends to leave the blastdesign simpler but more robust, at the cost of higher specific drilling and specific charge. The conclusions suggest that this unrealistic difficulty when compared to world average could be a simptom of the so-called “Brazilian cost” within the tunnelling industry."

Jan 1, 2017

By Joey R. Kish, Shooka Mahboubi, Hatem S. Zurob, Gianluigi A. Botton

The kinetics of the Cr2O3-based scale oxidation and volatilization were studied in the presence of water vapour (H2O). A commercial Cr2O3-based scale forming Type 310S stainless steel was examined at the ambient pressure (0.1 MPa) and 550ºC in relatively low and high H2O containing environments of air- 10% H2O and air- 70% H2O, respectively. The increase in the partial pressure of H2O (pH2O) from 10% to 70% resulted in transition of the oxidation and volatilization kinetics from the parabolic rate law for air-10% H2O to the paralinear rate law for air-70% H2O. The kinetics transition was attributed to the increase in the Cr loss rate from the base scale after coupons exposure in air- 70% H2O. The significant role of the Mn alloying element in the base scale protectiveness was also discussed in the context of the Cr2O3-based scale stability.

Jan 1, 2017

By D. H. Steve Zou, Cui Lin

"This paper first discusses the basic attributes of sustainable mining and the responsibilities of various steak holders including mining companies, governments, and engineers. It is followed by a brief overview of the current practice on regulations, inspections, waste management and mine closure planning in Canadian mining industry. A case study is then presented as an example of sustainable mining where mine planning, mineral recovery, environment protection, reclamation and community development were integral parts of the overall strategy. A comparison of the mine site before and after mining is made to demonstrate the ""best practice"" in modern mining.Sustainability in Mineral Resource Development Extraction of mineral resources and other natural resources on the Earth has been and will continue to be an essential activity necessary to support human’s life. We live on the planet and depend on the available resources to survive. The extracted materials form the base to support modern life. However, we must be aware of the fact that mineral resources are limited on the Earth and may not last forever. Every time we extract one ton of materials, there is one ton less. They are not able to regenerate or regrow. One can ask a simple question: How long will they last? Or, is there anything left for our great grandchildren and many generations to come? The answer is not simple. Some minerals have become scarce or about to deplete. Some minerals may last longer. The reserve of a type of minerals depends on what we have discovered and the minable amount depends on accessibility and technology we have. Even if there are minerals in the deep ground, we may be limited by our technological capability. At the same time, we also need to understand the action of mineral extraction from the ground and the consequences of that action. Mineral extraction is a very hard work. We must break the ground to extract the ore, either through surface mining or underground mining. This action means disturbance of the land where we live. The disturbance is much more visible in surface mining than underground mining. The disturbed land, if not properly reclaimed after mining, is not going to be reusable. The very purpose of extracting minerals from the ground is to support our life but the action has a negative impact on our life. How can we reduce and limit disturbance of land from the action of minerals extraction? How can we make the disturbed land reusable? These issues must be properly addressed and a balance achieved."

Jan 1, 2017

By I. Caraconcea, M. Cousineau, S. Gariepy

"Several base metal plants operate in low grade/high tonnage conditions which impose strict cost control on all fronts for their operations to remain profitable. This leads to decisions regarding plant design, procurement, operations and maintenance that often favor cost minimization over value optimization. This may hinder the representativeness of the metal accounting systems while this should be a priority in a low margin environment. Such poor representativeness not only creates confusion in plant scheduling but can also hide suboptimal metallurgical performance. Furthermore, this situation can run undetected for a while since one dominant feature of a poor metal accounting system is its poor self-awareness. During their practice, authors have particularly identified measurement bias and reproducibility, as well as their impact on metal recoveries as areas of concern. These issues have not been extensively reviewed in the specific context of precious metals in base metal plants. Pragmatic solutions are proposed either at the design stage for a new project or to retrofit an actual operation. These solutions should be based on a business analysis that set a value of information matching the contribution of precious metals as well as the potential to use such information to act toward increasing plant profitability. Conclusions are that trade-offs are an inherent part of the design/audit/retrofit of any metal accounting system in any plant processing either base or precious metals. However, compromises must be evaluated on economic/technical ground.INTRODUCTION Every mineral processing plant must produce metal accounting reports (Morrison, 2008) where estimated saleable metal flows and inventories are published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimization, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that state of the art metal accounting is instrumental for mining companies to reach and sustain high-quality corporate governance (Gaylard, Randolph, & Wortley, 2014). However, producing a metal accounting report involves much more than just printing it (Lachance, Leroux, & Gariépy, 2015a). The underlying metal accounting system (Figure 1) is responsible not only for the reliable production of the metal accounting reports but also for the quality of the outcome. As such, the crucial tasks of its design/audit/retrofit should neither be seen as ancillary nor be left as an afterthought."

Jan 1, 2017

By C. Debek, A. Wasilewicz, T. Czysz

"Both Polish and European hard coal mining nowadays faces the need of deepening shafts (significantly in some cases) or extending mining hoists, due to the exploitation of deeper coal deposits.In order to protect the crew working within a shaft, rope safety platforms (artificial shaft bottoms) are employed. Old solutions, based on rigid steel constructions with the external damping layers made of e.g. slag and up to several tens of metres long, are intended to absorb the energy of approximately 5 t mass falling a distance of 700 m. However, current requirements often assume a drop of 20 t to a depth of 1000 m or even more.More modern safety platform structures, made of one or more support rings with steel ropes stretched on them (rope platforms), are more compact (up to 3 m high) and lighter than traditional solutions. Multi-ring rope platforms with additional damping layers filling the empty spaces between the ropes are able to absorb sufficient energy to meet the current requirements.Single- and double-ring platforms have been employed in Poland to absorb the energy of approximately 5 t dropping to a depth of 900 m. They have been developed (and some have already been implemented) by SADEX Ltd. and are protected by various patents and patent applications.This paper presents a design for a triple-ring platform structure with six rope nets. FEM analysis was used to model the performance of the platform. According to the simulation, a 20 t mass falling from 1000 m (>100 m/s) will destroy all the nets, breaking most of the ropes and deforming the support steel boards placed on the nets, but will ultimately be stopped by the platform, as its kinetic energy falls to zero."

Jan 1, 2017

By K. Boakye, T. Newman, P. Bláha, M. B. Toelle

"This paper presents a quarry optimization plan using a block model and an in-house development quarry scheduling and optimization software (QSO Expert) to help improve quarry operations at Crystal River. The Crystal River Quarry is an underwater quarrying operation that barges limestone via the Gulf of Mexico, as the main source of raw material to a cement plant in Theodore, Alabama. To improve the quarry operation, an evaluation was completed to optimize the quarry planning and extraction procedures of the quarry. In order to achieve this, additional exploration drilling campaign was implemented, a new block model was re-calculated and the latest version of QSO Expert software was used. The primary economic impact is a higher recovery of limestone reserves; sustainability of resources, corresponding longer quarry life. Secondarily as the limestone is mined underwater and stockpiled above water, drainage reduces moisture content achieving direct cost reduction on limestone shipping. In addition, a considerable reduction in operational cost was achieved due to a significant decrease in consumption of electrical energy, reduced dragline maintenance costs and reduced dragline movements within the operation. INTRODUCTION Holcim is a Swiss-based global building materials and aggregates company. Founded in 1912, the company expanded into France and then throughout Europe and Middle East during the 1920s. In 1922, Holderbank, as the company was then known, expanded beyond the Swiss borders into France. By the end of the decade Holderbank held stakes in Belgium, Germany, the Netherlands, and Egypt (Holcim History 1912-2012) Positions in Lebanon and South Africa soon followed.. Holder bank later expanded in North America in the 1950’s. In the late 1970s and early 1980s, Holderbank continued its expansion in Latin America, Asia and Spain for the first time. The company expanded into Eastern Europe and experienced a boom in Spanish construction preceding the 1992 Summer Olympics. By 1986, Holderbank was the world's largest cement manufacturer. In the 1990s, the company consolidated its European holdings as the American market drove growth. Expansion into Eastern Europe and Russia continued (Holcim History 1912-2012). In 2001, the company changed its name from ""Holderbank Financière Glaris"" to Holcim (short for Holderbank ciment) (Holcim History 1912-2012). Holcim expanded by purchasing Aggregate Industries entering into the United Kingdom for the first time. That year, the company also expanded into India by acquiring a stakes in The Associated Cement Companies (ACC) and Ambuja Cement Eastern. In 2008, Holcim became the largest shareholder of China's Huaxin Cement with a 40% stake. In 2009, they acquired Cemex Australia. In 2014, Holcim and Lafarge announced they had agreed to terms on a ""merger of equals"" valued at nearly $50 billion in 2015. The new company LafargeHolcim based in Switzerland has a manufacturing capacity of 427 metric million tons a year."

Jan 1, 2017

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By Orestis Zarzouras, Amalia Giannakou, Jacob Chacko

"When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.IntroductionThe Izmit Bay bridge, a 3-km-long suspension bridge that crosses Izmit Bay in Turkey, is planned to be constructed in one of the most seismically active places in the world. The south approach structures for the Izmit Bay Bridge along the western side of the Hersek peninsula bring the bridge down from on the order of El. 60 meters at the South Anchorage to an elevated embankment approximately 1.3 km farther south (Figure 1). The south approach structures are located within a zone of secondary deformation around the primary trace of the North Anatolian Fault. The concept design team has developed a concept design for a “viaduct” structure that consists of 10 spans with lengths varying between 136 m and 100 m and two back spans one of 125 m, attached to the main bridge and the other of 74 m attached to the south embankment."

Jan 1, 2017

By Calvin Konya, Anthony Konya

Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industries, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, and the optimization of explosive load for the technique of Precision Presplitting.

Jan 1, 2017

By Jian Li, Robbie McDonald, David Robinson

"The pressure oxidation of sulfide minerals at temperatures above 200°C enables the extraction of base metals, improves the extractability of gold from refractory ores, enables solubilisation of PGEs and can be used to hydrothermally upgrade base metal-containing feeds. Fundamental studies reveal that the solution chemistry (and mineralogy of the solids) during pressure oxidation can be manipulated with outcomes that include (1) increased leaching rates, (2) lower oxygen requirements and (3) the formation of chemically more stable residues. This paper presents examples describing how these outcomes might be achieved based upon fundamental investigations.INTRODUCTION The application of pressure oxidation to the processing of gold ores and concentrates dates back several decades and continues to be the process of choice at operations such as Pueblo Viejo (pyritic gold) which host the largest autoclave of its kind in the world (Barrick Gold Corporation, 2016). Commercial application to the processing of base metals and PGMs resides with long established processes such as the Sherritt process, ore specific applications such as by Noril’sk, at Sepon etc. or has not proceeded to date beyond pilot scale testing (e.g. Phelps Dodge, CESL, Activox, Platsol). Recently there has been significant interest in hydrothermal upgrading options for concentrates including the NONOX and Toowong processes (Rohner et al., 2016; Weidenbach et al., 2016). The latter options suggest directions where sound knowledge of the underlying fundamentals enables novel outcomes and efficiencies to be obtained. It comes as no surprise that investigations similar to those underpinning these developing processes can be traced back several decades. It is not the subject of this paper to provide a historical perspective of the relevant autoclave chemistries but rather, to present some potential opportunities suggested by studies in our laboratories. Topics to be discussed in this paper include (1) control of metal extraction rates, (2) control of iron-residue composition and (3) control of sulfur oxidation and hence acid generation and oxygen requirements. The work described will focus upon the pressure oxidation of a nickel concentrate."

Jan 1, 2017

By J. R. Kadambi, C. Shingote, J. Furlan, R. Ke

"Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multi-phase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations, based in some part on the respective current-available theoretical models, and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone was explored with the aid of both computational and experimental techniques (Particle Image Velocimetry). In this study, the flow field with an air core has been investigated; in essence, the research was a two-phase problem, which caused some challenges on both the computational and experimental sides. Two turbulence models were used in the numerical calculations: the Reynolds Stress Model and Large Eddy Simulation. The computational studies are mainly focused on the prediction of the dimensions and shape of the air core. Different section planes of the hydrocyclone were selected as planes of interest and then were divided into several fields of view (FOV) for PIV measurements. Two dimensional experimental velocity vector maps were obtained in each of the fields of view. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. Keywords: Computational fluid dynamics (CFD); Hydrocyclone; Particle image velocimetry (PIV); Reynolds Stress Model (RSM); Large Eddy Simulation (LES). INTRODUCTION A hydrocyclone is a device used to separate a solid-liquid, liquid-liquid, solid-gas, or liquid-gas suspensions into at least two separate density or particle size components. Hence, the flow field of the hydrocyclone is generally considered a multi-phases flow system. Application of hydrocyclones have been used in numerous industries including oil, drilling, metal working, and mineral processing since 1891, when E. Bretney obtained the first patent for the predecessor design of all contemporary hydrocyclones. A modern hydrocyclone typically consists a cylindrical section at the top where the liquid is being fed tangentially, and a conical chamber attached to the bottom of the cylindrical section, as shown in Figure 1. The characteristics of the feed stream that is injected into the cylindrical chamber play a significant role in hydrocyclone operation. The inlet is tangential relative to the cylindrical chamber and hence causes a centripetal force in the flow field which is considered as the primary separation mechanism."

Jan 1, 2017

By M. Kumral, E. Dilhuydy, B. Ozdemir

"In-pit crushing and conveyor (IPCC) systems have become increasingly popular in the mining industry as an alternative to truck-and-shovel systems. Deciding whether to haul waste rock by truck or IPCC represents an important gap to be investigated in semi-mobile IPCC systems. A cost analysis is presented to evaluate the feasibility of crushing and conveying waste material in IPCC systems, along with sensitivity and risk assessments through Monte Carlo simulation. Although the capital expenditure is higher, results showed waste crushing will be feasible in deep pits and over long mine life and haul distances.RÉSUMÉ La popularité des systèmes de concassage et de transport dans la fosse minière (IPCC, de l’anglais In-pit crushing and conveyor) n’a cessé de croître dans l’industrie minière ; ils constituent en effet une option intéressante de remplacement des systèmes par camions et pelles mécaniques. Le choix entre le transport des stériles par camions ou par IPCC est encore difficile à faire et devra faire l’objet d’une étude approfondie au niveau des systèmes d’IPCC semi-mobiles. Une analyse des coûts est présentée pour évaluer la faisabilité du concassage et du transport des stériles par les systèmes d’IPCC, de même que des évaluations de la sensibilité et des risques par le biais de la simulation de Monte Carlo. Si les dépenses en immobilisations s’avèrent être plus élevées, les résultats ont cependant montré que le concassage des stériles sera envisageable dans des fosses profondes ainsi que sur une longue durée de vie et de longues distances de transport. INTRODUCTIONThe mining industry is currently facing many challenges such as low commodity prices, increasing environmental concerns and regulations, lower grades, deeper mines, and greater waste-rock quantities. As a result, the profitability of mining operations has decreased, with many mines stopping or suspending operations, and many new projects being postponed. Mining companies have therefore focused on improvements and innovations to increase the cost effectiveness of operations, for example, increasing production capacity to take advantage of the economies of scale (Crowson, 2003) and decreasing the unit operation cost. Changes in production capacity force mining companies to evaluate alternative material handling systems.During the past few decades and within material handling systems, significant improvements have been made to truck performance and capacity. Consequently, operating expenditures (OPEX) associated with fuel and maintenance have risen swiftly. In a mining operation, truck hauling systems now represent 40–50% of the capital cost and approximately 45% of the OPEX (Tutton & Streck, 2009). Additionally, material transportation costs are expected to increase due to longer haul distances arising from deeper and larger mines (Fleet et al., 2015). Finally, large fluctuations in fuel prices result in high risks associated with truck OPEX. According to the United States Energy Information Administration (2015), the cost of crude oil—the largest component of the retail price of diesel fuel—increased from US$24.31/barrel in 1986 to US$46.92/barrel in 2016, peaking at US$151.72/barrel in 2008 (Macrotrends, 2016)."

Jan 1, 2017

By Kegomoditswe Koitsiwe, Tsuyoshi Adachi

"This paper characterizes quarterly LME copper price fundamentals from 1995 to 2011 by analyzing the transformation of the market mechanism based on structural change perspective. Using chow test for structural change based on the least square multiple regression, we divide the price fluctuation into: Stable price period (1995Q3-1999Q2), Low stable price period (1999Q3 – 2003Q3) and Price fluctuation period (2003Q4 – 2011Q2). The results show the existence of structural breaks disproves the investigation of the full sample period as a whole. In different structural breakpoints the main drivers of copper prices changes and their impact are significantly different. Moreover, the paper examines the role of speculation in copper price fluctuations.Introduction The rise in commodities price volatility and financial and economic crisis have led to questions over the organisation of futures and physical commodities markets. Spikes in commodity prices and volatility have coincided with a surge in financial speculators in the commodity markets inspiring a polarised and hotly debate among academics and practitioners about the role of investors in the development of physical markets. In his seminal work Kaldor (1939) focused primarily on whether speculative activity in the futures markets reduces the variance of commodity spot prices. Yet, part of the literature finds that the introduction of futures contracts destabilizes the spot market. IMF (2006) studied commodities boom and its causes concluding that there is little support for the hypothesis that speculative activity affects either price levels over the long run or price swings in the short-run. The impact of speculative activity on commodity prices remains a highly contentious topic. Other market analysts take the view that the supply and demand for physical commodities remain the major determinants of market trends (Krugman 2008). It is the aim of this study to contribute to the literature by examining the drivers of copper price changes from a structural change perspective. In this context we are attempting to answer to: What are the main drivers leading to copper price fluctuations? Are these factors having the same effect in different periods or not? It is meaningful to understand drivers of copper prices and thereby, their fluctuations because it will help developing countries depending on copper export to anticipate market situation and avoid bad economic development challenges that can result from price fluctuations. Moreover, this can ensure sustainable mineral supply."

Jan 1, 2017