Search Documents

The Boliden Aitik concentrator in Sweden processes 2,000 tph of low grade copper ore. The plant consists of five grinding lines feeding four bulk flotation banks with a scavenger concentrate regrind mill, and a column cleaner circuit with a regrind mill. The authors installed a model-based expert, optimizing control system to maximize copper recovery in the bulk flotation circuit while maintaining an appropriate copper grade in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent addition rates. It combines the power of a dynamic population balance model which estimates mineral liberation in each stream, an optimizer which computes appropriate set points and a rule-based module which implements the strategy. The benefits have been evaluated over three months. The model-based expert, optimizing control system generates a measurable increase in copper recovery, around 0.5 per cent and an optimized bulk concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 1998

Interactive data exploration is essential for visualising grade distribution and geological controls on orbodies. Quick and appropriate computer techniques for making daily 'value adding' decisions include routine imaging of numerical data suc

Jan 1, 1998

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

By Mike Higgins

"Data management is emerging as a major concern for miners. Engineers today are faced with anextensive array of data from varying sources, and are required to consolidate and analyse thisinformation to produce an effective and efficient mine plan. The viability of a mining operation canbe dependent on the outcomes of this process. With so much at stake, it is no surprise that mostengineers prefer a standard approach to blasting which is designed to minimise risk rather thanoptimise performance."

Jan 1, 1998

By David A. Jack

The Mission Valley Viaduct is located in San Diego, California. This structure is the intersection of Interstate 8 and 805. The project consists of the main viaduct, 8 connecting ramps, and one highway overpass. This job was originally built back in the 70's. After the Loma Prieta Earthquake in 1989, Caltrans began an aggressive program to seismic retrofit all of its bridges throughout the state. Most retrofit designs required major upgrades to the existing footings. These footing upgrades consisted of either driven or drilled shaft piling. The existing footings of the Mission Valley interchange were supported on driven H pile. The soils throughout the site were dense sands and gravels, cobbles, occasional boulders with a dense sandstone bearing strata, which varied through out the site. It was this sandstone strata that the engineers designed their pile tips around. High ground water in sandy soils created a high probability of liquefaction in all of the upper stratas.

Jan 1, 1998

By Patrick R. Taylor

Titanium nitride has been synthesized in a thermal plasma reactor from ilmenite ore concentrate using methane and ammonia as the reactive gases. The product has been characterized by x-ray diffraction and SEM. Results show that a high concentration of methane favors the formation of iron, titanium nitride and titanium carbonitride. The formation of titanium carbonitride can be minimized by controlling the concentration of methane. The formation of TiN proceeds by the progressive reduction of the oxides of titanium to titanium, which is converted to titanium nitride.

Jan 1, 1998

By M Cooper

Since its enactment in 1991, the Resource Management Act (RMA) has generated both praise and criticism. The major criticism is in relation to the costs the Act poses to industry and the time it takes to work through the process. In response to such criticisms the Minister for the Environment has initiated a review of the implementation of the RMA. The Minister's proposals for reform have not yet been released and the discussion that follows is based upon the report by the Minister's Review Group which was released in September.

Jan 1, 1998

By S. Liu

A general account of nitrogen-generating systems, including the surface fixed, surface-mobile and underground-mobile types is presented. These systems have recently been adopted in coal mines in China to prevent and extinguish fires. The paper stresses nitrogen -injection technology and relevant systems of monitoring and stopping air leakage.

Jan 1, 1998

By K J. Kidd

There is general understanding of hoisting systems throughout the mining industry. However, the relative importance of the various parameters influencing hoist selection and utilization is not completely understood. In order to determine if these parameters can be identified and prioritized, data covering 613 hoist installations were compiled. The 613 installations represent hoisting systems in 30 countries on six continents. This study compares data to historical trends, correlates design parameters in an attempt to identify underlying selection criteria, and comments on the apparent trends in recent developments in hoist design.

Jan 1, 1998

Hydraulic transport of coal has been used for many years on the West Coast of New Zealand to extract small blocks of steeply dipping coal. Recent development at Strongman 2 Mine has seen the use of high pressure monitors to cut coal and a corresponding increase in the scale of production.This paper provides a brief introduction to hydraulic mining, describes the present system used at Strongman 2 and discusses future potential development.

Jan 1, 1998

By Margarete Kalin

"Biotechnological approaches to decommissioning of mine waste management areas are presented in the context of sustainable environmental management. Improved design of waste sites and environmental management paves the way for the application of new technological approaches. Mining wastes are better confined, effluent quantity is reduced and the quality is expected to improve in the future. The biologically mediated treatments focus on the creation of conditions inside the waste management area which lead to the confinement of the contaminants in the inactive tailings ponds and seepage collection ponds, as well as pits or other disturbed areas which were part of the operating conditions.Biogeochemical reactions lead to three fundamental water treatment steps mediated biogeochemically , alterations in chemistry which lead to formation of particles, which then have to flocculate and be assisted to collect in the bottom of the ponds. Microbially active sediments are installed to assist particulate formation and serve as sinks for metals. In deeper sediment strata, stable forms of metals are created. Biological polishing is used to collect the particulates and relegate them to the sediment. Examples will be given of the application of these processes, to waste rock piles, open pits and tailings ponds. This paper attempts to show that, through the integration of applied biotechnological advances and the application of new approaches to decommissioning, reductions of environmental impacts by mining are possible. * Note: this paper has been presented at the 13th Annual Meeting of BIOMINETIntroductionThe role of biotechnology in decommissioning of mining waste management areas should be placed in the context of sustainable development. The concept of sustainable development as defined by the Brundtland Commission (1987) for the restoration/ reclamation of mining operations could be translated as follows: The increasing demand for the resources by the world population must be met in a manner which does not compromise the earth's environment over the long term (Brooks et al., 1995)."

Jan 1, 1998

By Paul Clifford

The Florida Institute of Phosphate Research (FIPR) is an independent, state of Florida research agency. It was created in 1978 to conduct research to enhance the competitiveness of the Florida phosphate industry. The institute also conducts research to prevent, minimize or rectify environmental impacts caused by the industry. And it helps educate the public concerning phosphate-related technology and issues. FIPR is funded by a severance tax on the industry and is governed by a five-member board of directors appointed by the governor. FIPR's research is playing a role in enhancing the competitiveness of the Florida phosphate industry. Its technology research program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. It is developing new and improved methods of beneficiation and fertilizer production. This includes new process flowsheets and on-line analyzers and process control methods. FIPR is also developing uses for the phosphogypsum byproduct of phosphoric acid production and evaluating the risks associated with its uses.

Jan 1, 1998

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998

By Scott A

This paper summarises some of the results of the ACARP-JKMRC project 'Optimisation of Dozer Operations in Open Cut Mines'. The work has involved an industry review, design and conduct of field trials of coal seam preparation using dozers, nume

Jan 1, 1998

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By Toshiro Kuji, Masakazu Fujita, Tetsuji Saito

"The magnetic properties of the magnetic materials were deeply dependent on the microstructures. In this study, the novel technique to produce the desired microstructures in a controlled manner was proposed. The technique consisted of the production of the amorphous alloys and the control of the crystallization process. The technique was applied to improve the magnetic properties of Nd-Fe-B permanent magnets. The microstructural control of the magnets exhibited the excellently high energy-products of higher than 430 kJm-1. The relationship between the magnetic properties and the microstructures of the Nd-Fe-B permanent magnets was discussed.IntroductionThe intrinsic properties of the materials are basically determined by the properties of the constituent elements or the compounds. However, it is often noticed the difference between the observed properties and the theoretical values expected from the intrinsic properties of the materials. This indicates that the observed properties of the materials are determined not only by the properties of the constituent elements. In other words, the observed properties of the materials are also strongly dependent on the morphology of materials. This means that the microstructural control may creates a great improvement of the properties of materials.In Nd-Fe-B permanent magnets, the superiority arises from the uniaxial intermetallic Nd2Fe14B compound which has a large saturation magnetization and a high anisotropy field [1,2]. The magnetic properties of the Nd-Fe-B permanent magnets are dependent on the microstructure, that is, the size, shape and degree of the crystallographic alignment of the Nd2Fe14B phase. Currently, the Nd-Fe-B permanent magnets have been produced by either sintering or melt-spinning [3,4]. In the sintered magnets, alignment of the Nd2Fe14B phase is achieved by the prior green compaction of the crushed ingot powders in an applied magnetic field [3]. In the melt-spinning approach, alignment of the Nd2Fe14B phase is achieved by hot deformation [5]. Amorphous melt-spun ribbons are comminuted and then are consolidated into bulk form by hot pressing before hot deformation. As-hot-pressed magnets have randomly oriented Nd2Fe1~ grains [6]. Subsequent die upsetting of as-hot-pressed magnets gives rise to the crystallographic alignment of the Nd2Fe14B phase."

Jan 1, 1998

By R. Larry Grayson

In the October 1998 issue of the Holmes Safety Association Bulletin, NIOSH authors Mark Stephenson and Carol Merry wrote the article Hearing loss among miners and measures to protect hearing, which focused on the extensiveness of hearing loss among miners and the use of hearing protection to prevent hearing loss. While the primary importance of engineering controls in preventing hearing loss was discussed, since miners do not generally have control over their work en­vironment or assignments, the article focused on the importance of consis­tent use of hearing protection. In this article, all aspects of a compre­hensive approach to the prevention of hearing loss in miners will be covered. The discussions will do the following: ? describe application of the hierarchy of controls in preventing hear­ing loss in miners, ? give an example for each type of control measure and its impact, ? explain the major provisions, be­yond the hierarchy of controls, of the recent NIOSH document en-titled Criteria for a Recommended Standard: Occupa­tional Noise Exposure, Revised Criteria 1998 relative to a hearing loss prevention program, and ? summarize important points on control of noise exposure for every miner to remember, equipment in most facets of operations. Miners are well aware of noisy areas in or around equipment, icluding extraction machinery such as draglines, power shovels, longwall shearers, and continuous mining machines; powered haulage equipment such as load-haul-dumps, shuttle cars, large trucks, and continuous haulage units; roof bolting machines; jackleg drills and stopers; auxiliary equipment such as compressors, fans, and pumps; size reduction equipment, etc. They are not well aware of the insidious nature of pro­gressive hearing loss, which is per­manent, but they are generally aware of what levels of noise are hazardous and what measures can be taken to reduce their personal noise exposure. Behaviorally, however, there are many reasons why miners choose not to use hearing protection faithfully.

Jan 1, 1998

By G York

South African gold reserves extend to great depths. However, strategies for the mining of such deposits have changed only slightly over the past number of years. Regional support at depth is currently provided by rock pillars and backfill. Many problems have been experienced with these regional support practices at deeper levels. In this paper several alternative forms of regional support are described which include the use of concrete, the use of back area caving and confinement to strengthen pillars. These new concepts are supported by numerical and laboratory modelling and in situ results.

Jan 1, 1998

By R. R. Klimpel

The efficiencies of plant scale comminution processes are often evaluated by various indices that are calculated and/or measured somewhat independent of the performance of any associated downstream froth flotation processes. In order to compare some specific comminution factors such as energy utilization, media consumption, equipment utilization time, etc. comparisons of comminution efficiency independent of flotation behavior are appropriate. However, as more and more detailed plant level information is gathered on the joint and highly interactive nature of comminution and froth flotation, it is becoming increasingly obvious that knowing and using simple efficiency indices are not enough. What is needed are more performance related measures of the efficiencies of the combined size reduction -froth flotation system for effective plant level economic optimization to occur. The purpose of this paper is to present some examples of important interactions that influence the joint efficiencies of size reduction and froth flotation processes.

Jan 1, 1998