Search Documents

By R. H. Rubisov

Sulphuric acid pressure leaching of nickeliferous laterites has attracted considerable attention from the nickel industry during the past five years. The process is especially advantageous for limonitic laterites that mostly contain goethite, because iron precipitates releasing acid and thus rendering low acid consumption. It is also applicable to mixtures of limonites and saprolites, although at higher acid consumption due to magnesium. Effective process design requires the solubility of metals that precipitate during the process to be known. In the present work, determination of metal solubilities is based on a simple speciation program that assumes the presence of only one dominant complex for each metal. The thermodynamic data for the precipitation reactions are extracted from high-temperature experiments with monometallic systems published previously. The validity of the approach is then tested against mixed bimetallic systems, and finally applied to calculate the solubility of aluminium, iron and magnesium in laterite leaching effluents "at temperature". In both cases of limonitic feed and limoniticfsaprolitic blends, the prediction closely follows metal solubilities measured experimentally at temperatures from 230 to 270°C and at terminal he acidities ranging from 10 to 75 g/L.

Jan 1, 1999

By P. Mottahed, E. De Souza

One of the major unsolved problems of safe, economical roof support in the evaporite industry has been that of obtaining and maintaining anchorages in relatively soft rock. This is due to the viscoelastic and viscoplastic behaviour of salt rock and associated deposits. This paper introduces a low-cost, yieldable support mechanism, consisting of a system of buckling disks, which provides viable solutions to dynamic support. The yieldable support system offers a number of advantages in comparison with existing dynamic support systems. It is characterized by its simplicity in design and installation, repeatability in behaviour and cost effectiveness. It also has the added advantage of providing the operator with a means of assessing support behaviour and ground performance by direct visual observation of changes in disk shape. Thus, the system can be utilized as a warning mechanism of ground stress and support load conditions. Such system not only provides a feasible and more effective rock mass stabilization strategy but improves mine safety.

Jan 1, 1999

By Pupazzoni P. D, Meissner D. C

Incorporating an iron ore pelletising plant, a MIDREX'"' Direct Reduction Plant, and a mini mill, the conversion of iron ore fines to high- quality steel slabs in Western Australia is among the lowest cost routes in the world. The cost and availability of iron ore and natural gas, government support, and proximity to the growing Southeast Asian market all contribute to the competitive position of the area. Owing to the lead-time required, this is an ideal time to develop a new project to supply semi-finished steel to Asia for rolling to a finished product. A project contracted now will start up in about three years, when the market should have recovered.

Jan 1, 1999

By F. McGravie, S. T. Solinski, W. W. Robertson

During this, the Centennial year of the discovery of the Hall-Heroult process, it seems appropriate to review some of the developments which have taken place in Canada and to explain why it has become an important world centre for the production of primary aluminum. For many years after it was recognized that the element aluminum existed, scientists were frustrated in their efforts to isolate it. In the early 1800s H. C. Oersted and Frederick Woehler prepared small quantities sufficient to measure some of the physical properties. A quasi-commercial process involving reduction with metallic sodium was developed by the French scientist H. St. Claire Deville in 1855 but the cost was very high ($30. 00 per kg). It was not until 1886 that Charles Martin Hall in the United States and P.L.T. Heroult in France, more or less simultaneously but completely independently, discovered the process which is essentially that in use today. Some of the early pioneers in the industry quickly recognized the potential of the hydro-electric resources in Canada as economic energy suppliers for aluminum production. The first commercial production in Canada was in Shawinigan, Quebec in 1901, only 15 years after the process was discovered. Subsequently operating plants were established at nine different locations in Canada (Quebec and British Columbia) (Table 1). Operations continue today in all locations except one (La Tuque). The table shows present plant capacity which for the older plants was reached in an evolutionary manner including replacement of obsolete capacity or upgrading and modernization of existing designs.

Jan 1, 1999

By G. H. Blackwell

Open pit mine management must ensure that sufficient trucks are available and are being used effectively for production, and that operating costs are under continued control and review for improvements. This paper describes methods for estimating truck fleet requirements which have been used effectively at large- and medium-sized open pit mining operations. Applied to commonly available data, multiple regression analyses can indicate when mine plans should be revised toward optimizing the number of trucks required. Prediction of major cost items for budgetary purposes is addressed, along with an example of how readily available production data can be used to reduce costs systematically.

Jan 1, 1999

By M. Sahoo

The development of new alloys containing bismuth and selenium for potable water supplies are reviewed. The new alloys are replacements for the leaded red- and semi-red brasses by the low-lead alloys, SeBiLOYS I and II, for sand casting, and SeBiLOY III replaces the lead containing yellow brass, C85800, for permanent mold casting. As the new alloys use bismuth and selenium, the supply and demand of these elements are discussed. The key casting characteristics discussed are: tendency to dross formation, freezing range (liquidus and solidus temperatures), fluidity, resistance to hot tearing, microstructures, mechanical properties, machinability, grain refinement and corrosion behaviour.

Jan 1, 1999

By Alex Del Castillo

The mineral processing industry has followed the development of database control systems, and various systems have been installed in existing and new plants. The goal is to improve product quality, raise productivity and lower production costs. Improvements in different units for mineral .processing .have been applied. This has led to increasing information for the operators. To support the operators and for an easy overview of the process, a complete concept for an integrated process-control system is required. This paper describes the plant-wide [process control system for the Collahuasi copper project located in northern Chile. The total investment for the project was $1,700,000,000 and included a port area and two copper processing plants, an oxide plant with a cathode production of 50 tons per year and a sulfide plant with a concentrate production of 330 kilotons per year. The main characteristics of the plant-wide process control system include a 200- kilometer long redundant control network and a 24-kilometer long redundant serial network providing coverage for the entire plant. The plants are located around 4,700 meters above sea level, serial communication lids allow the integration of over 2,700 SCADA data units, and the system handles over 7,500 physical signals plus the SCADA data integration. The main equipment consists of 39 different sized controllers, 16 operator stations, 5 engineering stations, 2 information management systems and 4 X- terminals. The project management, control configuration, factory acceptance test, system integration test, training, commissioning and start-up were carried out in close cooperation with the customer. The result was completely satisfactory for the customer.

Jan 1, 1999

By Dolf Gielen

This paper discusses the results of a Western European energy and materials systems engineering study that analyses the impact of greenhouse gas (GHG) emission reduction on the future of the steel and aluminum industry. he technology selection will be significantly affected by future CO2 policies. The avail- ability of C02 removal and storage technology and the social acceptance of this strategy for GHG emission reduction is of key importance for the strategy selection. The use of coal based smelting reduction technologies is optimal in case of weak C02 policies or in case of strong C02 policies and low CO2 removal and storage costs. The selection of CCF or Corex technology depends on the penalty regime. However, if C02 removal proves to be problematic, CCF development fails and strong C02 policies are introduced, the gas based DRI production processes will become more attractive. In both cases, the energy efficiency of the iron and steel industry will further increase in the next decades. The impact of GHG emission reduction on aluminum prices and aluminum use can be significant. However contrary to common notions the aluminum production will be positively affected by GHG emission reduction, notwithstanding the currently high emissions in aluminum production. A combination of emission mitigation in production and significant GHG emission reduction effects further down the product chain cause this effect. A significant potential exists for improved materials efficiency. This potential is generally neglected in energy efficiency and CO2 reduction studies. However improved steel qualities are of similar importance for C02 emission reduction as increased energy efficiency. It remains to see if this potential will be used to its full extent in the next decades. Model calculations indicate that the impact of C02 policies on the competition with other materials will be limited. Greenhouse gas emission mitigation will have much more impact on materials production and waste handling than on materials consumption.

Jan 1, 1999

By Anton Sroka

The German hard coal production predominantly derives from underground multiseam mining activities. Beside common surface damages, ?inner mine damages? on underground infrastructures (i.e. main roads, cross cuts and shafts) due to mining excavations occur to an increasing extent. As these "inner mine damages" dramatically increased because of the development towards high performance longwall mining technologies, this matter raised to be a severe problem concerning mining economics. To protect durable and long lasting underground infrastructures, precautionary measures such as suitable mine layouts, adapted planning of mining operations and moderate face advances have to be considered. Some examples of "inner mine damages" recorded by means of mine surveying methods are given in this paper. An empirical-mathematical model based on the principles of mining subsidence engineering methods will be introduced. This model allows to minimize ?inner mine damages? and helps to support and optimize mining processes.

Jan 1, 1999

By P To, A Sharp-Paul, S Jones, C Monahan

A key environmental management issue associated with mining projects is tailing disposal. In high rainfall environments this is particularly challenging and generally requires the discharge of excess water from a tailing dam to adjacent streams or coastal waters. Such discharges can potentially have adverse impacts on downstream water quality and the environmental values associated with these waters, such as providing a drinking water supply for local villagers, maintaining a fisheries resource or protecting a fish species of high conservation significance. An alternative to the construction and operation of a conventional tailing dam is Deep Sea Tailing Placement (DSTP). The key features of such a system are:Discharge of the tailing slurry at considerable depth (approximately 120 - 150 m) below the oceanÆs surface. This requires a pipeline to be laid from the process plant to a mix tank, where the tailing is mixed with seawater and entrained air released. The pipeline then continues down the ocean floor to the required discharge depth, which is below the surface mixed layer and the euphotic zone. After discharge, formation of a density current which continues to descend along the ocean floor as long as the slope is sufficiently steep. Final deposition of the tailing in an area where the slope of the ocean floor is insufficient to maintain the density current. This typically occurs at depths of more than 800 m. Water quality issues associated with DSTP include: Impacts on the oceanic water column due to the formation of subsurface plumes which break away from the descending density current. The occurrence of elevated concentrations of contaminants in the interstitial waters of the deposited tailing solids. Fluxes of contaminants from the tailing deposits into the overlying oceanic water column. This paper discusses the water quality aspects of DSTP with particular reference to a case study in Papua New Guinea. The evaluations undertaken as part of the DSTP impact assessment included consideration of both the short- and long-term chemical behaviour of contaminants and bioassays, within the appropriate water quality assessment framework.

Jan 1, 1999

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

By F. F. Peng, Z. Lu

Employing a combination of two types of polyelcctrolyte might become necessary to enhance both the settling rate of the flocs and the water clarity of a fine-particle suspension in a high-capacity thickening process. The sequence of addition, mixing, type and dosage of polymer all affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance, i.e., a high settling rate of the flocs and the deisired underflow density and overflow water clarity. The required performance can be achieved by either adjusting the pH prior to anionic polyelectrolvte flocculation or using a combination of polymer flocculant and coagulant (dual-polymer system). The dynamic thickening test results showed that only the approach using a dualpolymer system is capable of meeting the required performance. The effects of polvelectrolvte dosage, the sequence and numbers of polyelectrolyte addition, the feed concentration, the bed level and the rake speed on the settling rate, underflow percent solids and water clarity were studied in cylinder tests and in a laboratory dynamic thickening unit. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively using total suspended solids in supernatant, underflow density and capacity per unit of settling area per unit of time. The objective of this study was to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1999

By Y. Prévost

The Noranda Continuous Converting Process was commissioned in November 1997 at the Home smelter in Rouyn-Noranda, Quebec, Canada. It has completed over 18 months of successful operation. Excellent team work and technical expertise contributed to achieve targeted production levels and environmental goals after only a few months of operation. The operating results have demonstrated the flexibility of the process in producing blister copper from a variety of copper feed materials including a combination of molten and solid copper matte, reverts and fluxes. This paper describes the startup activities and process optimization tasks performed during the first year of operation of the new Noranda Converter.

Jan 1, 1999

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999

By Sharon L. Eyer

"FTIR spectroscopy is employed to define mineable ore deposits based on exploration samples. The RAMBO (Robotic Assessment of Mineable Bauxite Ore) technology is operating successfully at an alumina refinery in K winana, Australia, for assessment of a number of critical ore attributes including available alumina, extractable organic carbon and total iron. Classical methods of analyses for these properties require laboratory-scale digestion of alumina ore (bauxite) or XRF analyses.Multivariate calibration is used in the RAMBO system to generate robust mathematical models that are able to estimate classical data from FTIR spectral data. Furthermore the models can highlight regions of ore that are relatively unusual. Unusual ore may be investigated for potential impacts on refinery processes well in advance of mining.The components of the technology are described and some results for an example application (bauxite) are presented. Challenges and difficulties are discussed. The potential to apply the technique to process control is introduced."

Jan 1, 1999

By Weber P, Sneyd S

The total world steel production in 1998 amounted to approximately 780 000 000 t. The share of electric steelmaking was in the range of 35 per cent and is expected to increase further to over 40 per cent of the world's production within the next ten years. As electric steelmaking is primarily based on the use of scrap and as it is progressing more and more into higher steel grades the need for low-residual metallics will become increasingly important. Consequently, the demand for scrap substitute material will increase, reflected in the world wide spate of interest for DRI (Direct Reduced Iron) and HBI (Hot Briquetted Iron). The increased significance of DRI/HBI as a substitute for steel scrap has obviously emanated also from its comparatively lower and more predictable costs per ton and definable chemistry. In 1998 already 37 million tons of DRI/HBI were globally produced.

Jan 1, 1999

By Gerald H. Luttrell, Jaisen N. Kohmuench, Michael J. Mankosa

A new separator, known as the Hydrofloat cell, has been developed to overcome limitations of traditional flotation cells in recovering coarse particles. In this process, small air bubbles are introduced into a hindered "teeter" bed of fluidized solids to create light bubble-particle aggregates that can be separated based on differences in density. Laboratory tests conducted with coarse phosphate feeds indicate that the Hydrofloat cell is capable of increasing BPL recoveries by nearly 20% over conventional flotation methods. Based on these encouraging results, a pilot-scale Hydrofloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the plus 35 mesh plant feed can be increased by more than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the plus 16 mesh particles in the Hydrofloat concentrate. This article describes the theoretical basis for the development of the Hydrofloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 1999

By M. H. Rogers

Coal has been at the forefront of mankind?s drive to improve his quality of life and also for sustainable development, from the Industrial Revolution onwards. The international coal industry today is large, with some 3,7 billion tons being produced and consumed in 1997. South Africa is an important participant in the coal industry, selling some 220 million tons in 1997 of which 64 million tons were exported. It is the second-largest thermal coal exporting country in the world. Despite the size of the world coal industry, it is not immune to change. The address examines growth projections for the industry and the change drivers that will impact on it in the future. Environmental pressures, the most important of which being the climate change debate, the Kyoto Protocol arising from this debate and the development of clean coal technologies, to reduce the impact of coal production and usage on the environment are considered. Other major change drivers considered are competition from other sources of energy and that between coal producers, the deregulation of the electric power industry, corporate restructuring and for the South African producer, legislative reform. The declining (real term) coal price, the consequent squeeze on margins and the need for producers to actively contain costs is covered. Technology has, in the past, been the driver behind the growth and change of the South African coal industry and its future role in ensuring that coal is the fuel of choice for continued improvement in standards of living and economic development is addressed.

Jan 1, 1999

By Ning Liu, Xuming Wang, Yongqiang Lu, Jan D. Miller

Bench-scale flotation experiments have been conducted to study the effect of nonionic polyethylene oxide (PEO) polymer surfactants on the flotation of Florida phosphate rock. It has been found that PEOs having a molecular weight from 1,200 to 8,000 are effective. Flotation results demonstrate that the addition of nonionic PEO has a favorable effect on phosphate flotation, especially on the flotation of coarse phosphate feed. At about the same collector level, phosphate recovery can be improved by 10-30% with PEO addition. The surface chemistry of phosphate flotation using the fatty acid/fuel oil/PEO system has also been studied to better understand the phenomena involved. The increase in phosphate recovery with PEO addition has been attributed to improved dispersion of fatty acid, which leads to better froth stability and a more hydrophobic surface state.

Jan 1, 1999

It has been proven theoretically and experimentally that the use of 10 - 30 per cent DRI in blast furnace along with iron ore or sinter results in lower coke rate and higher productivity. However, to-date this remains unpractised on a regular basis mainly because of economic reasons. The DRI produced by several methods are expensive and difficult to store/handle in large quantities because of its reactive nature and thus DRI in blast furnace remains unacceptable.

Jan 1, 1999