Search Documents

The knowledge in the field has been reviewed by literature studies, and using experience from personal research in sublevel caving. There is a lot of material regarding gravity flow of fine grained materials in bins, but the theory of flow for these materials are normally not applicable for coarse blasted rock. This study was therefore concentrated towards coarse rock fragments created after blasting in orebodies. The goal for this study was to make a report of known knowledge, and identify what we have to learn more about. The Bergmark-Roos theory, which was a paradigm shift in the science of gravity flow, is today the best mathematical theory for calculation of the drawbody for a homogenous material or when we wish to simulate the mean drawbody for a large number of draws. The Bergmark-Roos theory must however be improved, so it can take into account the flow pipe effect. When this is done it will be possible to construct a 3D computer model for calculation of ore extraction versus amount of loaded ore and waste. It is also necessary to find the 3D shape of the flow cone to be able to calculate the 3D ore rest that normally develops on footwalls. Calculations should be done for the draw on several sublevels including determination of the ore losses and temporary ore rests. First when this computer model is developed optimisation of ore recovery and waste rock dilution can start for a given orebody. The author points out the importance for international co-operation and standardisation of methods for determination of material properties. More field tests and model blasting tests should also be done. When enough knowledge is gathered, a handbook of the optimisation of sublevel and block caving should be written.

Jan 1, 2000

By S. J. Dillingham

As we enter the new century and close out the old, it has become standard procedure for most blasters to complete a blasting log or shot report following a blast. However, how can you be sure these completed blasting logs are worth the paper or electronic space they occupy.3 Is the recorded data accurate and meaningful? Will the blasting logs stand up under investigation? This paper will attempt to define the purpose of a blasting log, illustrate common mistakes, discuss potential problems, and indicate steps that a company or individual blaster can take to improve and protect against costly errors. The end result will be a reminder of the importance of accurate documentation following a blast that must be given the same individual effort as went into the blasting itself. This paper will also attempt to achieve a proactive training resource to improve the use of blasting logs. A completed blasting log is, quite possibly, the only witness to the overall credibility of the work of the responsible blaster. The log may remain perpetually silent, only to end up in a file that is moved progressively with time to various levels of long-term storage. But, will this silent witness be ready to speak out should a concern arise from the blasting ? Will the blasting log communicate with authority and credibility, or will it be ridiculed by investigation and silenced in shame with costly adverse results for the blaster and company? It is not enough to simply complete a blasting log. The information it contains must be accurate enough to stand the test of time and arduous scrutiny. Unfortunately, most blasters and their associated blasting companies do not realize the status of the silent witness until it is too late.

Jan 1, 2000

By Steve Kral

Through advanced technology and innovative thinking, the mining industry has become one of the world’s leading industries in environmental protection. But it only takes one Summitville, Omai or, most recently, the Aurul gold tailings retreatment operation in Romania to provide ammunition to the industry’s critics in their attempts to sway public opinion against mining. So for the mining industry to continue operating with the public’s support, it must continue to improve its tailings waste-disposal processes and the dams that hold this waste. In January, about 120 specialists in the mine waste management field gathered together to discuss the available technologies and materials for controlling mine waste and mill tailings disposal. “Tailings and Mine Waste’00” was held at Colorado State University in Fort Collins, CO. This meeting, begun in 1978, is a continuing symposium. It provides a forum for environmental professionals to discuss the state-of-the-art in mill tailings and mine-waste disposal methods.

Jan 1, 2000

By Masayuki Kudoh, Kiyotaka Matsuura

"Molten aluminum and nickel cast onto a steel block exothermically react and produce molten nickel monoaluminide, NiAI, which is simultaneously joined to the steel. The heat of the exothermic reaction is transferred to the steel block, and steel near the surface of the block is melted. The depth of the melted steel increases with both the initial temperature of the steel block and the thickness of the produced NiAI. Iron from the melted steel dissolves in the molten NiAI, and an intermetallic compound of NiAI-Fe pseudo-binary system is produced. During solidification of the intermetallic compound, it is strongly joined to the steel. The Ni.Al-Fe intermetallic compound has an excellent resistance to oxidation and corrosion.IntroductionAn intermetallic compound of nickel monoaluminide, NiAl, offers many advantages over conventional superalloys, such as higher melting temperature, lower density, greater specific modulus and higher thermal conductivity [1]. NiAl also exhibits excellent high-temperature oxidation resistance when doped with zirconium or hafnium, and excellent high-temperature corrosion resistance when doped with chromium or yttrium, that are superior to existing high temperature alloys or coating materials [1-4]. On the other hand, NiAI is significantly brittle at temperatures below 600 K [5-7], which is the most sigriificant disadvantage of NiAI. A possible way to overcome the disadvantage and to utilize NiAl as an environmental-resisting high-temperature structural material may be joining of NiAl to a ductile material."

Jan 1, 2000

Before I begin this paper, I thought that it would be important to start with a brief background on myself. This will give some insight into where I am coming from with some of the ideas presented in the body of the paper. I studied mining engineering at the University of New South Wales, graduating with Honours in 1999. When I finished university I was offered a job with PricewaterhouseCoopers in Sydney, working in the Energy and Mining Group of the Audit practice; which I accepted. I have been working at PricewaterhouseCoopers now since January 1999, completing an accounting conversion course at the University of Technology Sydney along the way. I am currently beginning my Professional Year for Chartered Accountant qualification. During my later years at university, continuing on through the start of my working career, I have been involved with the Sydney Branch of The AusIMM; firstly, as a student representative and, now, as the Young Professional Representative. Therefore, you can probably see that I will have very different young professional experiences than some of my peers who have been working on mining sites. The purpose of this paper is to examine the challenges that face graduates who are entering the industry and what solutions are used to ensure that this entrance is as smooth as possible. A challenge has then been made to the industry and The Institute in the form of further observations on ways that this entrance may be improved and the development of graduates to be more effective. In preparing this paper I have discussed various graduate experiences with some of my colleagues in order to see what some of the challenges they, themselves, face now and, also, going forward. I also discussed with them what they see as solutions to these challenges, drawing on some of my own experiences in a different company environment.

Jan 1, 2000

By Wade L. Karlsen

"Revision surgery to replace joints in the human body requires materials that are strong, long-lasting, and biocompatible. Metallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an on-going effort to economically improve their performance. Alloying with inert nitrogen can enhance the mechanical properties of the alloy, enhance its corrosion resistance, and elevate the temperature at which the metallic implants can be thermally treated, without increasing the threat to the human body. The current work has produced a high-nitrogen Co-Cr-Mo alloy through HIP consolidation of metal powders that have undergone nitriding in a mechanically fluidized bed. The already fine microstructure of the powders combined with the increased nitrogen content resulted in significant property gains in the consolidated materials.IntroductionMetallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an ongoing effort to improve their performance. Research on a Stellite 21 cobalt-chromiummolybdenum alloy has shown that nitrogen alloying can be desirable from several standpoints [l]. Firstly, it has indicated that nitrogen can enhance the mechanical properties of the alloy, which could allow more demanding implant designs. The same work also demonstrated that nitrogen can elevate the temperature at which the metallic implants can be thermally treated, which is desirable in situations in which surface textures are to be sintered to the implant to enhance its fixation properties. Finally, that research work discovered that, not only does nitrogen not harm the corrosion resistance of the cobalt-chromium-molybdenum alloys, but it may in fact enhance it. Combining this with the fact that small amounts of nitrogen are not considered a threat to the human body, makes nitrogen alloying an attractive alternative for enhancing the properties of Co-Cr-Mo."

Jan 1, 2000

By Don W. Murphy, Don M. Larsen

Advanced process control has been implemented at the Jerritt Canyon Mill. Plant production prior to 1997 was limited by grind circuit capacity. The installation of additional mill horsepower and an optimizing supervisory control system achieved a throughput increase in excess of 12 percent. The controller application utilized a seamlessly integrated fuzzy logic expert system for real-time mill control coupled with a neural network predictor for closed-loop feedback of particle size constraints. In late 1998, a second supervisory controller was installed to operate the fluidized bed roasters. The second controller optimized roasting conditions, increased plant throughput and improved metallurgical recovery.

Jan 1, 2000

By Alun J. Davies

This paper describes a design-build project for the construction of a tanker wharf for 150,000 dwt vessels. The tankers deliver oil from offshore oil fields to a Transshipment terminal on the south coast of Newfoundland. The project described is an expansion to a previously constructed facility, adding an additional berth. The first berth was designed conventionally as concrete structures supported on groups of independent, single piles. The second berth was awarded to Peter Kiewit Sons' Co. Ltd. based on an alternate design which utilized a "jacket" concept whereby prefabricated steel frames are placed on the seabed and serve as permanent templates and also give lateral support to the piles, thereby increasing their load capacity. This led to economies and time savings. Discussed herein is the design process and the field installation, covering the jackets, driven pipe piles, and the rock anchors.

Jan 1, 2000

By T. Goda, H. Kiuchi, M. Iguchi

"IntroductionThe utilization of silver in the electronic industry has been increasing in recent years. It is desirable that valuable metals are recovered from the used scraps of these industrial goods. Condensor chips, for example, contain silver, palladium, and Ag-Pd alloy. The dissolution behavior of silver was studied assuming that scraps such as used condensor chips in which Ag-Pd paste is used are subjected to wet treatment.ExperimentalIn this study the powder, granules, and flakes of silver were used in these nitric acid leaching experiments. The nitric acid solution was agitated in a glass reactor with a magnetic stirrer and heated to the required temperature. The experiment was started by putting the silver sample in the solution. After the leaching, the solution was filtered and the concentration of silver in the filtrate was analyzed by ICP.ResultsIn dilute nitric acid of less than 5 N, silver powder dissolved easily with increase in the concentration of nitric acid and temperature. However, the more intensive the stirring of the solution was, the lower the dissolution quantity became. Fig. 1"

Jan 1, 2000

By Jaroslav Horskoý, Miroslav Raudenský, Bogdan Filipic, Božidar Sader

This paper describes main elements and practical use of the computational system for automated setting of optimized casting conditions in the continuous casting of steel. The system consists of the heat transfer model of the process, empirical metallurgical criteria, and optimization algorithm. The physical model of the, strand temperature distribution relies on the classical Bennon-Incropera mixture continuum formulation for the convective-diffusive heat transport. Fluid flow effects are considered through enhanced thermal conductivity of the liquid phase. The model is solved by the operator-splitting Crank-Nicolson finite volume version of the Voller-Swaminathan scheme. The solution procedure is coupled with the IDS solidification analysis package. Boundary conditions for the strand cooling rely on combination of the generic and plant-specific mold, spray, and roll heat transfer coefficients ' by coping the effects of the casting speed, casting temperature, casting powder, mold oscillation mode, steel grade, water or air-mist spray type, running water, trapped water on the rolls, and radiation. The caster safety and productivity and the quality of the strand are related to nine empirical metallurgical criteria. The criteria ensure the caster safety and economy as well limit the internal, longitudinal, and transversal surface cracking possibility. The problem of finding optimum casting parameter values is stated as a minimization problem based on the analytical form of the cooling criteria evaluated from the steady-state temperature distribution of the strand. To solve the optimization problem, a genetic algorithm is employed. The algorithm explores process parameters settings heuristically by applying the principles of biological evolution. It starts with a random set of solutions and iteratively improves them through selection and variation. Solutions are evaluated by running the heat transfer model of the process and extracting the values of the empirical metallurgical criteria.

Jan 1, 2000

By Toshihide Takenaka, Takashi Matsui, Nao Murakami, Masahiro Kawakami

"Electrowinning of Ti have been investigated in a LiF-NaF-KF melt including K2TiF6 at 773-923K by applying electrochemical oxidation ofH2 gas as an anodic reaction. The cathodic behavior of titanium and the anodic behavior of H2 gas were studied by voltammetry in detail to clarify the electrolytic condition for the process. The electrowinning of Ti was carried out by potentiostatic _electrolysis. Steady electrolysis was achieved under the suitable electrolytic condition without breaking out the anode effect. Titanium metal was electrodeposited on a Ti cathode though the deposits were usually powdery. It is concluded that this process is potential if the morphology of the deposit can be improved.IntroductionTitanium has such good properties as high specific strength and high corrosion resistance. However, the availability of Ti has been limited because the price of Ti is much higher than those of other common metals, such as Fe and Al. The production process of Ti ingot from its ore is rather intricate so that the production cost is high. If the simpler process is developed, the production cost should be retrenched. Titanium metal is usually produced by the Kroll process, which consists of the electrowinning of Mg metal in molten salt and the chemical reduction of TiCl.i by Mg metal. The Kroll process is very elabrate, but not simple. Because the chemical reduction ofTiCl4 by Mg metal is highly exothermic, a considerable amount of energy is wasted.Titanium metal can be electrowon in molten salt bath in principle. A simpler and more effective process than the Kroll process may be realized by the direct electrowinning so that the electrowinning of Ti metal has been studied widely[ 1]. Some researchs progressed to a pilot plant stages [2], but the electrowinning of Ti has not been industrialized yet."

Jan 1, 2000

By Norihiko Fukatsu, Takashi Iwamoto, Noriaki Kurita, Koji Katahira, Kunihiro Koide, Teruo Ohashi

"The galvanic cell-type hydrogen sensor employing CaZro.9Ino.t03-a. as the solid electrolyte was designed for the measurement of hydrogen activities in molten copper under industrial .conditions. The sensor probe consists of the cap-shaped solid electrolyte with porous platinum electrode on the inside and alumina refractory tube. The gas mixture of the composition 4%H2-0.5%02-Ar was made to flow on the inside electrode. The hydrogen sensor probe was inserted directly into molten copper and the melt was used as the outer electrode. The effect of oxygen activity gradient to EMF was eliminated theoretically by measuring the oxygen activity in the melt simultaneously with an oxygen sensor. The high stability of output and excellent response to the change of hydrogen activity were obtained over the wide range of industrial copper melting conditions.IntroductionIn the metal casting process, hydrogen easily dissolves in molten metals from water vapor in the surrounding atmosphere. Owing to the large difference in hydrogen solubility between liquid and solid metal, dissolved hydrogen becomes a cause of the defects of blowholes in castings or ingots. It is necessary to control the hydrogen content in the molten metals [l]. Using proton-conducting ceramics as a solid electrolyte, high temperature-type hydrogen sensor can be constructed [2]. SrCe03- and BaCe03-based perovskite-type oxides exhibit appreciable proton conduction under hydrogen containing atmosphere at high temperature [3-5]. A hydrogen sensor for molten aluminum using CaZro.91no.103-a. has been developed and widely used in the ·process control in the aluminum melting industry [6,7]. The same type of hydrogen sensor has also been expected in the copper melting industry. .. However, CaZro.91no.103-a shows ·not only proton but also oxide ion conduction in the high temperature and at low oxygen activies like the copper melting· conditions. Then we studied the oxide ion conduction in CaZro.91no.103-a. iit · detail [8]. From the consideration on the EMF of the galvanic cell employing this material as electrolyte, it was shown that the unknown hydrogen activity may be precisely determined from cell potential which is corrected for the effect of oxygen potential gradient And the hydrogen sensor based in this principle was constructed and tested in laboratory-scale [9,10]. We repeated the similar tests in factory-scale and developed the sensor system for practical uses [11, 12]. In this report, the structure and system of the hydrogen sensor for molten copper will be introduced first. The reliability of the sensor will then be demonstrated from the results of experiments for sensor probes carried out in TYK's laboratory."

Jan 1, 2000

By G Lane, S Morrell

The design of the 12 m diameter SAG mill installed at the Cadia Hill Mine in New South Wales followed after two years of extensive laboratory and pilot plant testwork. The testwork showed the Cadia ores to be hard and competent necessitating the use of both a variable speed SAG mill drive and pebble crushing. The grinding power requirements for the SAG mill was based on engineering in-house grinding software, pilot plant data and simulations using JK SimMet software. Surveys of the SAG mill operation during the first four weeks showed the feed size distribution, transfer size and pebble rate to be lower or less than those for which it was designed. To compensate for the lower pebble rate, the SAG ball load was increased. This resulted in the total comminution circuit power being some 0.5 kWh/t higher than predicted. The JK SimMet SAG model has been modified to take account of these variations.

Jan 1, 2000

Increasingly specialized blasting needs require that the explosive energy available in a borehole be reliably known for representative blasting conditions. The underwater test, when properly performed, can yield such information and thus provide a reliable rating of explosives in terms of energy release. This paper reiterates the stringent experimental conditions to be satisfied, and data analysis and interpretation techniques to be followed to achieve this. This is supported by detailed experimental studies involving select parameters in both detonator and booster sensitive explosive compositions. The paper also illustrates the inadvisability of equating blasting performance with the commonly calculated energy values.

Jan 1, 2000

By R. Hiebert, M. Canty, S. Beckman

An innovative biological process is described for the treatment of cyanide-, metals- and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and to immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process-waste stream at a mine in Nevada. The demonstration was performed jointly under the Mine Waste Technology Program (MWTP), funded by the US Environmental Protection Agency (EPA) and jointly administered by the US De¬partment of Energy's (DOE) Western Environmental Technology Office (WETO) under Interagency Agree¬ment Number DW89938513-01-0. The Superfund Innovative Technology Evaluation (SITE) demonstration program was also involved in the project. MSE Technology Applications Inc. (MSE), Butte, MT, was the contractor responsible for conducting the project, and Pintail Systems Inc., Aurora, CO, was the technology provider. The pilot-scale unit was field-tested at Echo Bay's McCoy/Cove Mine southwest of Battle Mountain, NV. The biotreatment process was considered successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed from the mine process water. From the results of these pilot-scale tests, it was concluded that the biotreatment process potentially of¬fers an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 2000

By Leo Brewer, Kazuyoshi Shimakage, Mamoru Mitomo, Toshiyuki Nishimura, Yoichiro Uemura, Shinji Hirai

"In the synthesis process of ß -La2S3 via the sulfurization of La2O3 powder using CS2 gas, La2O2S was formed. This occurred at an initial stage of the reaction for sulfurization temperatures below 973K, and ß -La2S3 was also formed at a shorter period for higher sulfurization temperatures. It was found that the oxygen content in ß -La2S3 powders decreased gradually with an increase in sulfurization temperature. On the other hand, the carbon content in these powders increased gradually with an increase in the sulfurization temperature. Though it has been reported that ß -La2S3 was transformed to Y -La2S3 at 1723K± 50K, the sintered compact of double-phase Y -La2S3 and ß. -La2S3 was formed at a rather higher temperature of 1973K when the synthetic powder of ß -La2S3 containing a high amount of oxygen was used. However, phase transformation of -La2S3 to Y -La2S3 progressed preferentially with a decrease in the oxygen content of synthetic ß -La2S3 powder. The Seebeck coefficient of the sintered double-phase Y -La2S3 and -La2S3 was higher than that of the single-phase Y -La2S3, reported previously.Introduction La2S3 exists in three polymorphic forms that are similar to a series of Ce2S3, Pr2S3 and Nd2S3: a, ß , and Y'. The a -La2S3, which is stable at low temperature, is irreversibly transformed to ß -La2S3 of various compositions in the solid-solution range between La2S3 and La3S4, at 923 ± 50K. The -La2S3 may also be an oxysulfide of La10S14O2. Moreover, the ß .-La2S3 phase is transformed to Y -La2S3 ,which has a Th3P4 structure, at 1573 ± 100K. The melting point of Y -La2S3 is 2398 ± 30K where this temperature is similar to those of common refractory materials such as silica and alumina. Therefore, it can be predicted that y -La2S3 which has a high melting point and a thermodynamic stability due to the strong affinity of La for S, would have &high refractory character and chemical inertness in many molten metals. The y -La2S3, colored vivid faint yellow is stable up to 623K in air, where oxidation starts. y -La2S3 is frequently used as pigments for plastics and paints3. Furthermore, Y -La2S3 which is a semiconductor, is considered to be useful as a thermoelectric conversion materials, because it has a high Seebeck coefficient."

Jan 1, 2000

By M Delaney

Alliancing is a contractual relationship in which organisations with an interest in a project are brought together in an atmosphere of co-operation to produce superior results to benefit all of the participants. Fundamental to the concept is the management of the risks associated with the project. The traditional risk management strategy adopted by clients has been to transfer this risk to others in the belief that this will result in the lowest overall project cost. It is assumed that competition in the market place will allow these risks to be transferred without paying a premium. However, this approach often results in the development of an adversarial climate, a high level of litigation, time and cost overruns and an overall poor project outcome. Under an alliancing arrangement the parties (client, designer and contractor) are aligned through shared interests in the projectÆs success by linking profitability to performance. Under such an arrangement, an atmosphere is created whereby the participants are motivated to focus on cost-savings, pursue best value and to innovate. Successful alliancing can result in highly motivated project teams and realisation of extraordinary productivity and cost-savings flowing from increased efficiencies. The situations in which alliancing can be successful are discussed with particular reference to the Wandoo Alliance which successfully completed the $375 million Wandoo B offshore oil platform in record time and with considerable savings to the project budget.

Jan 1, 2000

By S Jahanshahi, T Norgate

In single stage copper making appreciable amounts of copper report to the slag phase. Various strategies are available to minimise copper losses to the slag. However a slag treatment stage is likely to be required in an economically viable process. A number of slag treatment process options are available and include: flotation, leaching and thermal reduction. In the design of an industrial process some type of economic as well as technical analysis of these options will be required. In this paper an outline of the techno-economic analysis procedure used to design a single stage copper making process is presented. The calculated operating and capital costs of industrial copper making processes are compared and used to determine the optimum single stage copper making flowsheet. The most economic slag treatment options is flotation of slags containing low amounts of copper.

Jan 1, 2000

By Y. Ide, K. Kishitake

It is expected that an Al-Cr-N composite nitride film may have a higher resistance to oxidation at elevated temperatures than the well-known Ti-Al-N films. The formation conditions of Al-Cr-N films by a de reactive sputtering method and their properties were studied in this study. The films characterized with respect to their high temperature properties such as chemical composition, crystal structure, microhardness, wear and· friction. The crystal structure of the Al-Cr-N films changed from hexagonal phase to cubic phase with an increase in Cr content in the films. The resistivity to thermal oxidation of the Al-Cr-N films is superior to that of usual TI-Al-N films. A half of the friction coefficient in the Al-Cr-N film was obtained comparing with that in the ordinary TI-Al-N film at room temperature and the wear rate of Al-Cr-N film was 2 order smaller than that of TI-Al-N film. The Al-Cr-N films show a small friction coefficient at 500°C and then they are recognized to have good tribological characteristics.

Jan 1, 2000

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000